Changes on emitter discharge under different water temperature and pressure

The study was conducted at the Research Laboratory of Hydraulic and Irrigation Group in the Rural Engineering Department, Technical University of Madrid (Universidad Politecnica de Madrid), Madrid, Spain. Water temperatures of 20, 30, 40 degrees C and system pressures often encountered in irrigation practices of 80, 90, 100, 110, 120, 130, 140, 150, 160, 170, 180, 190 and 200 k Pa were applied to determine the effects of different water temperatures and pressures on emitter discharge. Non-pressure compensating in-line emitter which has turbulent flow regime with a long-path (labyrinth), emitter discharge was 4 L h(-1) at system pressure of 100 kPa according to the manufacturer recommended, was used. Emitters were spaced 20 cm along the drip laterals with 16 mm diameter. Discharge equations and coefficients of variation related to temperatures of 20, 30 and 40 degrees C were obtained as q = 0.375H(0.51), q = 0.358H(0.52), q = 0.346H(0.53) and 2.68, 2.09, 3.65, respectively. Discharge of the emitter was affected by different system pressures and increased as potentially (R = 0993-0996). In general. the emitter discharge increased with increasing temperature. However, especially in the common system pressures of 90-120 k Pa, differences of obtained emitter discharges between the different water temperatures were not significant (1%).

Analysis of Semi-solid Processing for Metal Matrix Composite Synthesis Using Factorial Design

The main goal in this work is to conduct a quantitative analysis of the mechanical stir casting process for obtaining particulate metal matrix composites. A combined route of stirring at semi-solid state followed by stirring at liquid state is proposed. A fractional factorial design was developed to investigate the influence and interactions of factors as: time, rotation, initial fraction and particle size, on the incorporated fraction. The best incorporations were obtained with all factors at high levels, as well as that very long stirring periods have no strong influence being particle size and rotation the most important factors on the incorporated fraction. Particle wetting occurs during stirring at semisolid state, highlighting the importance of the interactions between particles and the alloy globularized phase. The role of the alloying element Mg as a wettability-promoting agent is discussed. The shear forces resulting from the stirring system is emphasized and understood as the effect of rotation itself added to the propeller blade geometry.

Relation among optical, thermal and thermo-optical properties and niobium concentration in tellurite glasses

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Delay from fracture to hospital admission: a new risk factor for hip fracture mortality?

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Física estatística aplicada a sistemas sociais através do estudo de redes complexas

In this work a study of social networks based on analysis of family names is presented. A basic approach to the mathematical formalism of graphs is developed and then main theoretical models for complex networks are presented aiming to support the analysis of surnames networks models. These, in turn, are worked so as to be drawn leading quantities, such as aggregation coefficient, minimum average path length and connectivity distribution. Based on these quantities, it can be stated that surnames networks are an example of complex network, showing important features such as preferential attachment and small-world character

Determinação das castas em Scaptotrigona postica (Latreille) (Hymenoptera, Apidae, Meliponini): diferenciação do ovário

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Three New Species of Salacia from Mesoamerica (Celastraceae, Salacioideae)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Gravitational and quantum bounds on the photon mass

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Simultaneous Determination of Two Groups of Elements in Milk by Electrothermal Atomic Absorption Spectrometry: Evaluation of Ruthenium Modifiers

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Comparative description and discussion of spermiogenesis and spermatozoal ultrastructure in some species of Heptapteridae and Pseudopimelodidae (Teleostei: Siluriformes)

Os dados obtidos no presente estudo sobre a ultraestrutura da espermiogênese e dos espermatozóides de Pseudopimelodidae e Heptapteridae mostram que eles compartilham algumas características, mas são bastante diferentes uns dos outros. As principais diferenças são a ocorrência de espermiogênese do tipo I em Pseudopimelodidae e do tipo III em Heptapteridae, a presença de fossa nuclear em Pseudopimelodidae e sua ausência em Heptapteridae, a presença de uma peça intermediária longa em Pseudopimelodidae e uma peça intermediária curta em Heptapteridae, a presença de um canal citoplasmático em Pseudopimelodidae e sua ausência em Heptapteridae, a presença de muitas vesículas grandes na peça intermediária de Pseudopimelodidae, e a presença de vesículas muito alongadas e dispostas em posição periférica distal em Heptapteridae e mitocôndrias distribuídas em toda a peça intermediária de Pseudopimelodidae e muito próximas ao núcleo em Heptapteridae. Heptapteridae e Pimelodidae compartilham várias características como a espermiogênese do tipo III, o mesmo padrão de condensação da cromatina e a ausência de fossa nuclear e projeções laterais ou fins. O espermatozóide de Pseudopimelodidae é mais similar aos dos Siluridae, porém a ausência de dados adicionais sobre a espermiogênese e o espermatozóide de outros siluriformes ainda limitam uma discussão mais ampla na ordem.

Determinação de rotina do crômio em fezes, como marcador biológico, pelo método espectrofotométrico ajustado da 1,5-difenilcarbazida

O objetivo deste estudo foi ajustar o método espectrofotométrico da 1,5-difenilcarbazida à determinação do crômio em fezes, como marcador biológico, adequando-o à rotina laboratorial. Fatores que poderiam exercer interferência na transformação do crômio (III) à crômio (VI) foram testados, como a recuperação do metal, quantidade de amostra, quantidade e ordem de emprego dos ácidos oxidantes da digestão úmida, temperatura e tempo de digestão e perda por volatilização do crômio como cloreto de cromila, porém não se determinou estatisticamente interferência destes fatores. No método ajustado, a amostra é digerida pela clássica mistura ácida nítrica/perclórica, levando a oxidação do crômio (III) a crômio (VI), e alíquota do extrato diluído é usado para reação com 1,5-difenilcarbazida; as absorbâncias são medidas a 550nm, utilizando-se de cubetas de um centímetro de caminho óptico, contra prova em branco conduzida simultaneamente. Dicromato de potássio foi empregado como substância de referência para obtenção da curva padrão na faixa de 0,25 - 2,5mg.mL-1 de Cr2O3 (1mg Cr2O3 º 1,9355mg K2Cr2O7).

INSULATOR-TO-METAL TRANSITION IN POLYTHIOPHENE

In the present work, the electronic structure of polythiophene at several doping levels is investigated by the use of the Huckel Hamiltonian with sigma-bond compressibility. Excess charges are assumed to be stored in conformational defects of the bipolaron type. The Hamiltonian matrix elements representative of a bipolaron are obtained from a previous thiophene oligomer calculation, and then transferred to very long chains. Negative factor counting and inverse iteration techniques have been used to evaluate densities of states and wave functions, respectively. Several types of defect distributions were analyzed. Our results are consistent with the following: (i) the bipolaron lattice does not present a finite density of states at the Fermi energy at any doping level; (ii) bipolaron clusters show an insulator-to-metal transition at 8 mol% doping level; (iii) segregation disorder shows an insulator-to-metal transition for doping levels in the range 20-30 mor %.

Thermal-optical properties of Ga : La : S glasses measured by thermal lens technique

In this work the quantitative theoretical treatment for two beam mode mismatched thermal lens spectrometry is applied to investigate the thermo-optical properties of chalcohalide (chalcolgenides and halides mixture) glasses. For the three kinds of glass studied the thermal diffusivity varied between 2.5 and 2.7 x 10(-3) cm(2) s(-1). Using these results and supposing Dulong-Petit specific heats we estimated the thermal conductivity and temperature ratio of optical path length (ds/dT) and temperature coefficient of refractive index (dn/dT). All samples had positive ds/dT(similar to 3.3 x 10(-6) K-1) and negative dn/dT (similar to -26 x 10(-6) K-1). The difference between these parameters and the change of signal are consequences of the expansion coefficient (13 x 10(-6) K-1) and refractive index (n similar to 2.6) of chalcohalides. (C) 1999 Elsevier B.V. B.V. All rights reserved.

Temperature and wavelength dependence of the thermo-optical properties of tellurite and chalcogenide glasses

The refractive index and the temperature coefficient of the optical path length change of tellurite (80TeO(2):20Li(2)O) and chalcogenide glasses (72.5Ga(2)S(3):27.5La(2)O(3)) were determined as a function of temperature (up to 150 degrees C) and wavelength (in the range between 454 and 632.8 nm). The tellurite glass exhibits the usual refractive index dispersion in the wavelength range analyzed, while anomalous refractive index dispersion was observed for the chalcogenide glass between 454 and 530 nm. The dispersion parameters were determined by means of the single-effective oscillator model. In addition, a strong dependence of the temperature coefficient of the optical path length on the photon energy and temperature was found for the chalcogenide glass. The latter was correlated to the shift of the optical band gap (or electronic edge) with temperature, which was interpreted by the electron-phonon interaction model. (C) 2007 American Institute of Physics.

Thermo-optical characterization of tellurite glasses by thermal lens, thermal relaxation calorimetry and interferometric methods

In this work the thermal lens, thermal relaxation calorimetry and interferometric methods are applied to investigate the thermo-optical properties of tellurite glasses (in mol%: 80TeO(2)-20 Li2O(TeLi), 80TeO(2)-15Li(2)O-5TiO(2) (TeLiTi-5) and 80TeO(2)-10Li(2)O-10TiO(2) (TeLiTi-10)). Thermal diffusivity, thermal conductivity, specific heat and the temperature coefficients of refractive index, optical path length, thermal expansion and electronic polarizability were determined. The use of three independent methods was useful for a complete characterization of the studied tellurite glasses. In addition, our results showed that the thermal expansion coefficient and the temperature coefficient of the optical path length (dS/dT) were significantly modified with the introduction of titanium, which may be relevant for the application of these glasses in the photonic area. (c) 2006 Elsevier B.V. All rights reserved.