Estudo térmico e de materiais de um compósito à base de gesso e EPS para construção de casas populares

A housing unit was built to study the thermal performance, and of material using a composite made of gypsum and EPS ground. We used two techniques of construction, using blocks, and filling on the spot. Two compositions of the composite were studied. The blocks were fixed using conventional mortar. In the technical of filling on the spot were used PET bottles up inside the walls to provide mechanical and thermal resistance. Compression tests were realized according to the ABNT standard of sealing bricks. It is going to be shown an analysis of the thermal comfort through the use of thermocouples placed on the walls of the building, internally and externally. The manufacturing viability of houses, using recyclable materials, through the use of composite materials proposed will be demonstrated. The constructive aspects showing the advantages and disadvantages of the technique used also will be broached. The block used presents structural functions and thermal insulating, is low cost and represents an alternative to the use of EPS and PET bottles which are materials that end up occupying much space in the landfills, giving than an ecologically correct use. The results of thermal analysis shows the thermal comfort provided by the composite by the obtainment of a difference between the internal and external surfaces of the walls more exposed to the sun around 7º C. The average temperature of the air inside the building, around 28.0 º C was below the zone of thermal comfort recommended for countries with hot weather

Efeito de adições poliméricas na aderência de pastas de cimento a tubos metálicos após ciclagem térmica

Thermal recovery methods, especially steam injection, have been used to produce heavy oils. However, these methods imply that the metallic casing-cement sheath interface is submitted to thermal cycling. As a consequence, cracking may develop due to the thermal expansion mismatch of such materials, which allows the flow of oil and gas through the cement sheath, with environmental and economical consequences. It is therefore important to anticipate interfacial discontinuities that may arise upon Thermal recovery. The present study reports a simple alternative method to measure the shear strength of casing-sheath interfaces using pushthrough geometry, applied to polymer-containing hardened cement slurries. Polyurethane and recycled tire rubber were added to Portland-bases slurries to improve the fracture energy of intrinsically brittle cement. Samples consisting of metallic casing sections surrounded by hardened polymer-cement composites were prepared and mechanically tested. The effect of thermal cycles was investigated to simulate temperature conditions encountered in steam injection recovery. The results showed that the addition of polyurethane significantly improved the shear strength of the casing-sheath interface. The strength values obtained adding 10% BWOC of polyurethane to a Portland-base slurry more than doubled with respect to that of polyurethane-free slurries. Therefore, the use of polyurethane significantly contributes to reduce the damage caused by thermal cycling to cement sheath, improving the safety conditions of oil wells and the recovery of heavy oils

Estudo térmico e de materiais na construção de casas populares com blocos confeccionados a partir de um composto a base de cimento, gesso, eps e raspa de pneu

We built an experimental house on an UFRN´s land using blocks made by a composite consisting of cement, plaster, EPS, crushed rubber and sand. Several blocks were made from various compositions and we made preliminary tests of mechanical and thermal resistance, choosing the most appropriate proportion. PET bottles were used inside the block to provide thermal resistance. In this work, a second function was given to the bottles: to serve as a docking between the blocks, because the ends of the cylinders came out of each block on top as well as at the bottom, with the bottom cut, allowing to fit of the extremities of the upper cylinder of a block in the lower holes of the other one, which were formed by the cutting already mentioned. Minimum compression tests were performed according to ABNT standards for walls closing blocks (fence). With that house built, we did studies of thermal performance in order to ascertain conditions of comfort, checking external and internal temperatures in the walls and in the ambient, among other variables, such as wind speed and relative humidity. The resulting blocks provided adequate thermal insulation to the environment, where the walls presented differences up to 11.7 ºC between the outer and inner faces, getting the maximum temperature inside the house around 31 °C, within the so-called thermal comfort zone for warm climates. At the end of the experiments it was evident the effectiveness of that construction in order to provide thermal comfort in the internal environment of the house, as well as we could confirm the viability of building houses from recyclable materials, reducing the constructive costs, becoming a suitable alternative for low- incoming families. Moreover, besides the low cost, the proposal represents an alternative use of various recyclable materials, therefore considered an ecological solution

Análise de desempenho de um fogão solar construído a partir de sucatas de antena de tv

Given the growing environmental crisis caused by degradation, mainly due to the use of polluting energy sources, increasing the growing use of renewable energies worldwide, with emphasis on solar energy, an abundant supply and available to everyone, which can be harnessed in several ways: electricity generation; dehydration of food; heating, disinfection and distillation and cooking. The latter has as its primary feature the viability of clean, renewable energy for society, combating ecological damage caused by large-scale use of firewood for cooking foods, use in tropical countries with high solar radiation, and has funding NGOs throughout the world with the goal of achieving low-income population. The proposed project consists of a solar cooker for concentration, working from the reflection of sunlight by a hub that they converge to a focal point at the bottom of the pot, getting lots of heat. The solar cooker under study consists of two elliptical reflecting parabolas made from the recycling of scrap TV antenna, having 0.29 m² of surface area for each antenna, which were covered by multiple mirrors of 2 mm thick and mounted on a metal structure, with correction for the mobility of the apparent movement of the sun. This structure was built with the recycling of scrap metal, possessing a relatively low cost compared with other solar cookers, around US$ 50.00. This cost becomes negligible, since that will involve a great benefit to not have fuel costs for each meal, unlike the use of gas or firewood for cooking food. The tests show that the cooker has reached the maximum temperature of 740 ° C, for boiling water in an average time of 28 minutes, cooking various types of foods such as potatoes, rice and pasta in an average time of 45 minutes and still going as a solar oven, making pizza baking and meat. These cooking times do not differ much from the cooking times on a gas stove, it becomes the solar cooker as a good consumer acceptance, and furthermore not to deliver the same gases that can poison the food as with the wood stove. Proves the viability of using the stove to cook or bake in two daily meals for a family, still presenting a position to improve his performance with the addition of new materials, equipment and techniques

Palhada do sorgo de guiné gigante no estabelecimento de plantas daninhas em área de plantio direto

A palhada na superfície do solo pode interferir na infestação de plantas daninhas das culturas de verão. O objetivo deste trabalho foi avaliar o efeito da quantidade de palhada do sorgo de guiné gigante sobre a população de plantas daninhas em área de plantio direto. O delineamento experimental foi de blocos ao acaso com quatro repetições. Os tratamentos constaram de 0, 6.100, 7.100, 19.500, 26.700, 28.100 e 30.200 kg ha-1 de palhada do sorgo de guiné sobre os quais foi realizada a semeadura de soja cultivar Monsoy-6101 na densidade de 25 sementes por metro e no espaçamento de 0,45 m entre linhas. Trinta dias após a semeadura, realizou-se o levantamento de plantas daninhas, em quatro amostras por parcela, por meio de moldura metálica de 1 m². Houve redução significativa do número de plantas daninhas estabelecidas com o incremento da palhada. A partir de 15.000 kg ha-1,o controle de plantas daninhas é superior a noventa por cento.

Análise térmica e mecânica de um compósito de matriz cerâmica com carga de EPS e raspa de pneu para construção de casas populares

Space Science was built using a composite made of plaster, EPS, shredded tires, cement and water. Studies were conducted to thermal and mechanical resistance. Inside the mold EPS plates were placed in order to obtain a higher thermal resistance on the wall constructed, as well as to give it an end environmentally friendly in view of both the tire and the EPS occupy a large space in landfills and year need to be degraded when released into the environment. Compression tests were performed according to ABNT blocks to seal, measurements of the temperature variation in the external and internal walls using a laser thermometer and check the temperature of the indoor environment using a thermocouple attached to a digital thermometer. The experiments demonstrated the heat provided by the composite values from the temperature difference between the internal and external surfaces on the walls, reaching levels of 12.4 ° C and room temperature in the interior space of the Science of 33.3 ° C, remaining within the zone thermal comfort for hot climate countries. It was also demonstrated the proper mechanical strength of such a composite for sealing walls. The proposed use of the composite can contribute to reducing the extreme housing shortage in our country, producing popular homes at low cost and with little time to work

Viabilidade térmica de um forno solar fabricado com sucatas de pneus

The proposed design provides a solar furnace alternative, box-like, low-cost operation to be used in cooking, comprising three scrap tires to make the recycling thereof. The tires were coupled to each other, forming an enclosure, which stood on its bottom covered by a parable multiple mirrors made from a urupema (sieve indigenous) and the inner sides of the oven aluminum sheet painted black, obtained from beer cans, thus being made to obtain the increase in the concentration of solar radiation incident on the inside of the prototype studied. Two tires were attached, leaving an air layer between them, with the function of thermal insulation. The third tire aimed to support the other two and thermally insulate the bottom of the oven. Externally was placed a metal frame with flat mirrors to reflect the incident rays into the oven, having a mobility to correct the apparent motion of the sun. Its primary feature is the viability of clean, renewable energy to society by tackling the ecological damage caused by the large-scale use of wood for cooking food. The tests show that the furnace reached the maximum temperature of 123.8 °C and baking various foods such as pizza, bun, and other lasagne in an average time 50 minutes. Proves the feasibility of using the oven. Presenting still able to improve their performance with the addition of new materials, equipment and techniques

Manutenção da umidade do substrato durante o teste de germinação de Brachiaria brizantha

Para avaliar procedimentos para a manutenção da umidade do substrato durante o teste de germinação de Brachiaria brizantha. Estudou-se o efeito da posição das caixas plásticas na câmara de germinação sobre a perda de água semanal, testando-se nove posições verticais (bandejas) e três posições horizontais (porta, meio e fundo do germinador). Foi também avaliado o efeito de procedimentos para manter a umidade do substrato, sobre a germinação, a perda de água semanal e o tempo despendido para a instalação do teste. Os procedimentos testados foram: (a) vedação da caixa plástica com vaselina, (b) vedação com saco plástico dobrado em quatro e colocado entre a tampa e a caixa, (c) colocação da caixa tampada dentro de saco plástico, (d) espuma sob o papel de germinação e (e) testemunha, caixa apenas tampada. Concluiu-se que a câmara de germinação promove a desidratação desigual do substrato conforme a posição das caixas; aquelas localizadas na primeira bandeja superior são as mais prejudicadas. Entre os procedimentos, a vedação com vaselina, a colocação da caixa dentro de saco plástico e a vedação com saco plástico dobrado em quatro entre a tampa e a caixa são eficientes na manutenção da umidade do substrato em taxas que não alteram os resultados do teste de germinação de B. brizantha; os dois últimos procedimentos são os mais rápidos e práticos, adaptando-se à rotina de um laboratório de análise de sementes.

Avaliação da eficiência de catalisadores comerciais na obtenção de biodiesel de algodão (Gossipium hisutum L.)

The increasing demand for energy and the environment consequences derived from the use of fossil energy, beyond the future scarcity of the oil that currently is the main power plant of the world, it stimulated the research around the production of biodiesel. In this work the synthesis of biodiesel of cotton in the methyl route was carried through, for had been in such a way used catalyst commercial homogeneous, Na-Methylat and the K-Methylat, aiming to the evaluation of the efficiency of them. An experimental planning 23 was elaborated aiming to evaluate the influence of the variable (molar reason oil/alcohol, % of catalyst and temperature) in the process as well as indicating the excellent point of operation in each case. The biodiesel was analyzed by gaseous chromatography, indicating a conversion of 96,79% when used Na-Methylat® as catalytic, and 95,65% when the K-Methylat® was used. Optimum result found with regard to the conversion was obtained at the following conditions: molar reason oil/alcohol (1:8), temperature of 40°C and 1% of catalyst Na-Methylat, reaching a 96,79% conversion, being, therefore, above of the established for the European norm (96.5%). The analysis of regression showed that the only significant effect for a confidence level of 95%, was of the changeable temperature. The variance analysis evidenced that the considered model is fitted quite to the experimental response, being statistically significant; however it does not serve inside for make forecasts of the intervals established for each variable. The best samples were analyzed by infra-red (IR) that identified the strong bands of axial deformation C=O of methylic ester, characterized through analyses physicochemical that had indicated conformity with the norms of the ANP, that with the thermal and rheological analyses had together evidenced that biodiesel can be used as combustible alternative in substitution to diesel

Síntese e caracterização de tungstatos de cério e estrôncio para fins catalíticos

The main goal of this work was to produce nanosized ceramic materials of the family of the tungstates (tungstates of cerium and strontium), and test them for their catalytic activity in processes involving the transformation of methane (CH4). The methodology used for the synthesis of the ceramic powders involved the complexation combining EDTA-citrate. The materials characterization was performed using simple and differential thermogravimetry, x-ray diffraction, transmission electron microscopy, and energy dispersive spectroscopy (EDS). The microstructure analysis was performed using the refinement by the Rietveld method, and the crystallite size and distribution of the materials was elucidate by the Scherrer and Williamson-Hall methods. The conditions of the synthesis process for the three envisaged materials (SrWO4, SrWO4 using tungsten oxide concentrate as raw material, and Ce2(WO4)3) were adjusted to obtain a single phase crystalline material. The catalytic tests were carried out in the presence of methane and synthetic air, which is composed of 21% O2 and 79% N2. The analysis of the conversion of the reaction was done with the aid of an fourier transform infrared device (FTIR). The analysis showed that, structurally, the SrWO4 produced using raw materials of high and poor purity (99% and 92%, respectively) are similar. The ideal parameters of calcination, in the tested range, are temperature of 1000 °C and time of calcination 5 hours. For the Ce2(WO4)3, the ideal calcination time and are temperature 15 hours and 1000°C, respectively. The Williamson-Hall method provided two different distributions for the crystallite size of each material, whose values ranged between the nanometer and micrometer scales. According to method of Scherrer, all materials produced were composed of nanometric crystallites. The analyses of transmission electron microscopy confirmed the results obtained from the Williamson- Hall method for the crystallite size. The EDS showed an atomic composition for the metals in the SrWO4 that was different of the theoretical composition. With respect to the catalytic tests, all materials were found to be catalytically active, but the reaction process should be further studied and optimized.

Avaliação cinética e potencial do Nb2O5 obtido a partir de um complexo de nióbio para formação do oleato de metila através da reação de esterificação do ácido oleico

Among the heterogeneous catalysts materials made from niobium show up as an alternative to meet the demand of catalysts for biodiesel production. This study aims to evaluate the potential of a heterogeneous catalyst derived from a complex of niobium in the reaction of methyl esterification of oleic acid. The catalyst was synthesized after calcination at different temperatures of a niobium complex ((NH4)3[NbO(C2O4)3].H2O) generating a niobium oxide nanostructure with a different commercial niobium oxide used to synthesize the complex. The commercial niobium oxide, the complex niobium and niobium catalyst were characterized by thermogravimetry (TG and DTA), surface area analysis (BET), scanning electron microscopy (SEM) and X-ray diffraction (XRD), showing the catalyst has researched morphological and crystallographic indicating a catalytic potential higher than that of commercial niobium oxide characteristics. Factorial with central composite design point, with three factors (calcination temperature, molar ratio of alcohol/oleic acid and mass percentage of catalyst) was performed. Noting that the optimal experimental point was given by the complex calcination temperature of 600°C, a molar ratio alcohol/oleic acid of 3.007/1 and the catalyst mass percentage of 7.998%, with a conversion of 22.44% oleic acid in methyl oleate to 60 min of reaction. We performed a composite linear and quadratic regression to determine an optimal statistical point of the reaction, the temperature of calcination of the complex at 450°C, the molar ratio of alcohol/oleic acid 3.3408/1 and mass percentage of catalyst of 7.6833% . Kinetic modeling to estimate parameters for heterogeneous catalysis it set well the experimental results with a final conversion of 85.01% with 42.38% of catalyst and without catalyst at 240 min reaction was performed. Allowing to evaluate the catalyst catalytic studied has the potential to be used in biodiesel production

Equilíbrio líquido-líquido para o sistema biodiesel de óleo de semente de melão (Cucumis melo l.) + metanol + glicerina

Rio Grande do Norte, northeast state from Brazil, it is the greatest producer and exporter of yellow melon, well known as Spanish melon. Despite the consumption of this fruit to be mainly its pulp, melon seeds are an important source of lipids considered an industrial residue it has been discharge product. The use of oilseeds in order to produce biodiesel establishes an important raw material and the increase of its production promotes the national development of the agriculture. In this background, the aim of this work has been to use oil from seeds of yellow melon to produce biodiesel and to accomplish a study of the phase equilibrium of the system evolving biodiesel, methanol and glycerin. The biodiesel was obtained by oil transesterification through methylic route with molar ratio 1:9.7 (oil:alcohol) and with a mass of NaOH of 0.5% from the oil mass; the reaction time was 73 minutes at 55 °C. A yield of 84.94% in biodiesel was achieved. The equilibria data present a well-characterized behavior with a great region of two phases. The tie lines indicate that methanol has a best solubility in the phase that is rich in glycerin. Consistency of the experimental data was made based on Othmer-Tobias and Hand correlations which values above 0.99 were found to correlation coefficients, this fact confers a good thermodynamic consistency to the experimental data. NRTL and UNIQUAC models were employed to predict liquid-liquid equilibrium of this system. It was observed a better concordance of the results when NRTL was applied (standard deviation 1.25%) although the UNIQUAC model has presented a quite satisfactory result either (standard deviation 2.70%). The NRTL and UNIQUAC models were also used to evaluate the effect of temperature in the range of 328 K to 358 K, in which a little change in solubility with respect to the data obtained at 298 K was observed, thus being considered negligible the effect of temperature

Efeito Kerr magneto-óptico; Ressonância ferromagnética; Acoplamento bilinear; Acoplamento biquadrático

In this work, we investigated the magnetic properties of a monocrystalline Fe thin film and of Fe(80 Å)/Cr(t)/Fe(80 Å) tri-layers, with the nonmagnetic metallic Cr spacer layer thickness varying between 9 Å < t < 40 Å. The samples were deposited by the DC Sputtering on Magnesium Oxide (MgO) substrates, with (100) crystal orientation. For this investigation, experimental magneto-optical Kerr effect (MOKE) magnetometry and ferromagnetic resonance (FMR) techniques were employeed. In this case, these techniques allowed us to study the static and dynamical magnetization properties of our tri-layers. The experimental results were interpreted based on the phenomenological model that takes into account the relevant energy terms to the magnetic free energy to describe the system behavior. In the case of the monocrystalline Fe film, we performed an analytical discussion on the magnetization curves and developed a numerical simulation based on the Stoner-Wohlfarth model, that enables the numerical adjustment of the experimental magnetization curves and obtainment of the anisotropy field values. On the other hand, for the tri-layers, we analyzed the existence of bilinear and biquadratic couplings between the magnetizations of adjacent ferromagnetic layers from measurements of magnetization curves. With the FMR fields and line width angular dependencies, information on the anisotropy in three layers was obtained and the effects of different magnetic relaxation mechanisms were evidenced. It was also possible to observe the dependence of the epitaxy of the multilayers with growth and sputtering parameters. Additionally it was developed the technique of AC magnetic susceptibility in order to obtain further information during the investigation of magnetic thin films

Avaliação do comportamento em fadiga de juntas estruturais de ligas de Al2024T3 coladas com adesivo epóxi

Ligas de alumínio são extensamente usadas em partes aeronáuticas devido às boas propriedades mecânicas e baixa densidade. Estas partes devem ser unidas para formar conjuntos maiores. Uma junta estrutural é definida como um segmento de estrutura que provê um meio de transferir carga de um elemento estrutural para outro. A maioria das juntas aeronáuticas é mecanicamente fixada com múltiplos prendedores (parafusos ou rebites). Estas juntas apresentam uma alta concentração de tensões ao redor do prendedor, porque a transferência de carga entre elementos da junta acontece em uma fração da área disponível. Por outro lado, as cargas aplicadas em juntas adesivas são distribuídas sobre toda a área colada e reduz os pontos de concentração de tensão. Juntas são a fonte mais comum de falhas estruturais em aeronaves e quase todos os reparos envolvem juntas. Portanto, é importante entender todos os aspectos de projeto e análise de juntas. O objetivo deste trabalho é comparar estaticamente juntas estruturais de ligas de Al2024-T3 em três condições: juntas mecanicamente rebitadas, juntas coladas e uma configuração híbrida rebitada e colada. Foi usada a norma NASM 1312-4 para confecção dos corpos-de-prova. Além disso, foram conduzidos testes de fadiga, sob amplitude de carregamento constante e razão de tensão igual a 0,1 para avaliar a eficiência dos elementos estruturais durante sua vida em serviço. Os resultados mostraram que a configuração híbrida apresenta maior resistência estática e uma vida em fadiga superior à configuração colada.

Avaliação do comportamento termoanalítico e oxidativo do biodiesel de mamona

In this work biodiesel was gotten through the transesterification reaction using the oil of castor as source of triglycerides and using the methylic route for obtaining of esters. For the characterization of biodiesel and its mixtures with mineral diesel oil, physical chemical parameters and several analytical techniques had been used, as well as: gas chromatography (GC), nuclear magnetic resonance of proton (1H NMR), infrared spectroscopy (IR) and thermal analysis. The chromatography confirmed the complete reaction of esters in biodiesel presenting a 97,08% conversion. The 1H - NMR presented singlet in 3,6 ppm corresponding to the hydrogen of the group ester RCOO CH3. The infrared presented a strong band in 1741 cm-1 referring to stretching C=O of ester and an average band in 1175 cm-1 referring C O deformation. With the data of thermal analysis it was possible to observe the thermal and oxidative stability of the samples changing the atmospheres of synthetic air and nitrogen, where stages of the thermal decomposition had been verified and had been attributed to the volatilization and/or decomposition of the triacylglycerides. The thermal degradation of the samples was carried through 150 and 210°C during 1, 12, 24 and 48 hours and was observed change in the thermogravimetric profile, therefore an increase in the number of stages of the thermal decomposition also occurred indicating characteristic intermediate composites of polymerization, being this confirmed through the rheological study that presented brusque increase of viscosity. The kinetic study showed that the activation energy has the following order: biodiesel > mineral diesel oil > mixtures biodiesel/diesel