Enhancement of optical absorption by modulation of the oxygen flow of TiO2 films deposited by reactive sputtering

Oxygen-deficient TiO2 films with enhanced visible and near-infrared optical absorption have been deposited by reactive sputtering using a planar diode radio frequency magnetron configuration. It is observed that the increase in the absorption coefficient is more effective when the O-2 gas supply is periodically interrupted rather than by a decrease of the partial O-2 gas pressure in the deposition plasma. The optical absorption coefficient at 1.5 eV increases from about 1 x 10(2) cm(-1) to more than 4 x 10(3) cm(-1) as a result of the gas flow discontinuity. A red-shift of similar to 0.24 eV in the optical absorption edge is also observed. High resolution transmission electron microscopy with composition analysis shows that the films present a dense columnar morphology, with estimated mean column width of 40nm. Moreover, the interruptions of the O-2 gas flow do not produce detectable variations in the film composition along its growing direction. X-ray diffraction and micro-Raman experiments indicate the presence of the TiO2 anatase, rutile, and brookite phases. The anatase phase is dominant, with a slight increment of the rutile and brookite phases in films deposited under discontinued O-2 gas flow. The increase of optical absorption in the visible and near-infrared regions has been attributed to a high density of defects in the TiO2 films, which is consistent with density functional theory calculations that place oxygen-related vacancy states in the upper third of the optical bandgap. The electronic structure calculation results, along with the adopted deposition method and experimental data, have been used to propose a mechanism to explain the formation of the observed oxygen-related defects in TiO2 thin films. The observed increase in sub-bandgap absorption and the modeling of the corresponding changes in the electronic structure are potentially useful concerning the optimization of efficiency of the photocatalytic activity and the magnetic doping of TiO2 films. (C) 2012 American Institute of Physics. [http://dx.doi.org/10.1063/1.4724334]

Direct Determination of Sugar Cane Quality Parameters by X-ray Spectrometry and Multivariate Analysis

Current methods for quality control of sugar cane are performed in extracted juice using several methodologies, often requiring appreciable time and chemicals (eventually toxic), making the methods not green and expensive. The present study proposes the use of X-ray spectrometry together with chemometric methods as an innovative and alternative technique for determining sugar cane quality parameters, specifically sucrose concentration, POL, and fiber content. Measurements in stem, leaf, and juice were performed, and those applied directly in stem provided the best results. Prediction models for sugar cane stem determinations with a single 60 s irradiation using portable X-ray fluorescence equipment allows estimating the % sucrose, % fiber, and POL simultaneously. Average relative deviations in the prediction step of around 8% are acceptable if considering that field measurements were done. These results may indicate the best period to cut a particular crop as well as for evaluating the quality of sugar cane for the sugar and alcohol industries.

Influence of the Sol-Gel pH Process and Compact Film on the Efficiency of TiO2-Based Dye-Sensitized Solar Cells

The influence of pH during hydrolysis of titanium(IV) isopropoxide on the morphological and electronic properties of TiO2 nanoparticles prepared by the sol-gel method is investigated and correlated to the photoelectrochemical parameters of dye-sensitized solar cells (DSCs) based on TiO2 films. Nanoparticles prepared under acid pH exhibit smaller particle size and higher surface area, which result in higher dye loadings and better short-circuit current densities than DSCs based on alkaline TiO2-processed films. On the other hand, the product of charge collection and separation quantum yields in films with TiO2 obtained by alkaline hydrolysis is c. a. 27% higher than for the acid TiO2 films. The combination of acid and alkaline TiO2 nanoparticles as mesoporous layer in DSCs results in a synergic effect with overall efficiencies up to 6.3%, which is better than the results found for devices employing one of the nanoparticles separately. These distinct nanoparticles can be also combined by using the layer-by-layer technique (LbL) to prepare compact TiO2 films applied before the mesoporous layer. DSCs employing photoanodes with 30 TiO2 bilayers have shown efficiencies up to 12% higher than the nontreated photoanode ones. These results can be conveniently used to develop optimized synthetic procedures of TiO2 nanoparticles for several dye-sensitized solar cell applications.

Photocatalytic activity of nanostructured anatase coatings obtained by cold gas spray

[EN] This article describes a photocatalytic nanostructured anatase coating deposited by cold gas spray (CGS) supported on titanium sub-oxide (TiO22x) coatings obtained by atmospheric plasma spray (APS) onto stainless steel cylinders. The photocatalytic coating was homogeneous and preserved the composition and nanostructure of the starting powder. The inner titanium sub-oxide coating favored the deposition of anatase particles in the solid state. Agglomerated nano-TiO2 particles fragmented when impacting onto the hard surface of the APS TiO22x bond coat. The rough surface provided by APS provided an ideal scenario for entrapping the nanostructured particles, which may be adhered onto the bond coat due to chemical bonding; a possible bonding mechanism is described. Photocatalytic experiments showed that CGS nano-TiO2 coating was active for photodegrading phenol and formic acid under aqueous conditions. The results were similar to the performance obtained by competitor technologies and materials such as dip-coating P25 photocatalysts. Disparity in the final performance of the photoactive materials may have been caused by differences in grain size and the crystalline composition of titanium dioxide.

Multiscale fabrication of functional materials for life sciences

Regenerative medicine claims for a better understanding of the cause-effect relation between cell behaviour and environment signals. The latter encompasses topographical, chemical and mechanical stimuli, electromagnetic fields, gradients of chemo-attractants and haptotaxis. In this perspective, a spatial control of the structures composing the environment is required. In this thesis I describe a novel approach for the multiscale patterning of biocompatible functional materials in order to provide systems able to accurately control cell adhesion and proliferation. The behaviour of different neural cell lines in response to several stimuli, specifically chemical, topographical and electrical gradients is presented. For each of the three kind of signals, I chose properly tailored materials and fabrication and characterization techniques. After a brief introduction on the state of art of nanotechnology, nanofabrication techniques and regenerative medicine in Chapter 1 and a detailed description of the main fabrication and characterization techniques employed in this work in Chapter 2, in Chapter 3 an easy route to obtain accurate control over cell proliferation close to 100% is described (chemical control). In Chapter 4 (topographical control) it is shown how the multiscale patterning of a well-established biocompatible material as titanium dioxide provides a versatile and robust method to study the effect of local topography on cell adhesion and growth. The third signal, viz. electric field, is investigated in Chapter 5 (electrical control), where the very early stages of neural cell adhesion are studied in the presence of modest steady electric fields. In Chapter 6 (appendix) a new patterning technique, called Lithographically Controlled Etching (LCE), is proposed. It is shown how LCE can provide at the same time the micro/nanostructuring and functionalization of a surface with nanosized objects, thus being suitable for applications both in regenerative medicine in biosensing.

Untersuchung des Reorientierungsverhaltens und Strukturierung dünner amphiphiler Blockcopolymerfilme zum Aufbau von Kompositen

Grundlage für die hier gezeigte Arbeit stellt die Eigenschaft von amphiphilen Blockcopolymeren dar immer den Block mit der niedrigsten Grenzflächenenergie zum angrenzenden Medium an die Oberfläche zu bringen. Durch einen Austausch des Mediums an der Grenzfläche zum Blockcopolymer kann eine Reorientierung erzwungen werden, wenn die Grenzflächenenergie des anderen Blocks nun die niedrigere Grenzflächenenergie besitzt. Dieses Verhalten von dünnen amphiphilen Blockcopolymerfilmen wurde zur Strukturierung von Oberflächen ausgenutzt und in nachfolgenden Synthesen weiter verstärkt. Um dies zu erreichen wurde das zur Strukturierung erforderliche Poly(4-Octylstyrol)block(4-hydroxystyrol) durch kontrollierte radikalische Polymerisationsmethode mit dem Tempo Unimer (2,2,6,6-Tetramethyl-1-1(1-phenyl-ethoxy)-piperidin) synthetisiert. Für die geplanten Reorientierungen und Modifizierungen von Oberflächen wurden dünne Filme durch Schleuderbeschichtung auf verschiedenen Substraten (Siliziumwafern, Glassubstraten und Goldoberflächen) hergestellt. Das Verhalten der Oberflächen von diesen Filmen wurde durch Kontaktwinkelmessungen untersucht. Auf diese Weise konnte gezeigt werden, dass die Oberfläche von Polymerfilmen nach der Präparation aus dem hydrophoben Block des Polymers gebildet wird. Durch Kontakt des Polymerfilms mit Wasser kann dieser zur Reorientierung gebracht werden, so dass der hydrophile Block des Polymers an der Oberfläche erscheint. Dieses Verhalten wurde zur Strukturierung mit softlithographischen Techniken genutzt. Dazu wurden hydrophil/hydrophob strukturierte Oberflächen durch Aufsetzen von hydrophoben PDMS-Stempeln, die Teile der Oberfläche selektiv abdeckten, und Einbringen von Wasser in die dabei entstehenden Kapillaren hergestellt. Dies ermöglichte es die Oberfläche selektiv im Größenbereich von 500nm bis zu 50µm zu strukturieren und an den reaktiven Bereichen Materialien, wie z.B. Kupfer, Titandioxid, Polyelektrolyte, photonische Kristalle und angegraftete Polymere, mit verschiedenen Methoden selektiv auf die Oberfläche aufzubringen. Um den Reorganisationsprozess der Oberfläche genauer zu studieren, wurde ein für diese Aufgabe besser geeignetes Polymer (Poly(Styrol)-block-poly(essigsäure-2-(2-(4-vinyl-phenoxy)-ethoxy)ethylester)) synthetisiert. Aus diesem Blockcopolymer wurden wieder dünne Filme durch Spincoaten hergestellt. Die Reorientierung dieses Polymers in 70°C warmen Wasser konnte durch Kontaktwinkelmessungen und NEXAFS Spektroskopie nachgewiesen werden. Mit Hilfe der NEXAFS Spektroskopie konnte festgestellt werden, dass die Geschwindigkeit der Reorientierung durch eine exponentielle Funktion beschrieben werden kann. Eine Auswertung der Geschwindigkeitskonstante für die Reorientierung einer hydrophilen zu einer hydrophoben Oberfläche des Polymers bei 60°C führt zu =75min. Aufgrund des exponentiellen Charakters der Reorientierung macht es den Anschein, dass die Reorientierung bei verschiedenen Reorientierungstemperaturen bis zu einem gewissen Grad erfolgt und dann stoppt. Eine weitere Reorientierung scheint erst wieder bei einer Temperaturerhöhung zu beginnen. Aus AFM Messungen ist ein Beginnen der Reorientierung durch Bildung kleiner Löcher in der Polymeroberfläche zu erkennen, die sich zu runden Erhöhungen und Vertiefungen vergrößern, um letztendlich in ein spinodales Entmischungsmuster über zu gehen. Dieses heilt dann im Laufe der Zeit langsam durch Verschwinden der hydrophilen Bereiche langsam aus. Der Beginn des zuvor beschriebenen Reorientierungsprozesses einer hydrophilen Oberfläche in eine hydrophobe konnte sowohl in den AFM, als auch in den NEXAFS-Messungen zu ca. 50°C bestimmt werden.

Application of a hybrid blocking layer in dye-sensitized solar cells

In dye-sensitized solar cells a blocking layer between the transparent electrode and the mesoporous titanium dioxide film is used to prevent short-circuits between the hole-conductor and the front electrode. The conventional approach is to use a compact layer of titanium dioxide prepared by spin coating or spray pyrolysis. The thickness of the blocking layer is critical. On one hand, the layer has to be thick enough to cover the rough substrate completely. On the other hand, the serial resistance increases with increasing film thickness, because the layer acts as an ohmic resistance itself. In this thesis an amphiphilic diblock copolymer is used as a functional template to produce an alternative, hybrid blocking layer. The hybrid blocking layer is thinner than the conventional, compact titanium dioxide film and thereby possesses a higher conductivity. Still, this type of blocking layer covers the rough electrode material completely and avoids current loss through charge recombination. The novel blocking layer is prepared using a tailored, amphiphilic block copolymer in combination with sol-gel chemistry. While the hydrophilic poly(ethylene oxide) part of the polymer coordinates a titanium dioxide precursor to form a percolating network of titania particles, the hydrophobic poly(dimethylsiloxane) part turns into an insulating ceramic layer. With this technique, crack-free films with a thickness down to 24 nm are obtained. The presence of a conductive titanium dioxide network for current flow, which is embedded in an insulating ceramic material, is validated by conductive scanning force microscopy. This is the first time that such a hybrid blocking layer is implemented in a solar cell. With this approach the efficiency could be increased up to 27 % compared to the conventional blocking layer. Thus, it is demonstrated that the hybrid blocking layer represents a competitive alternative to the classical approach.

Lichtsammler hinter Glas : Stabilisierung und Funktionalisierung des pflanzlichen Hauptlichtsammelkomplexes (LHCII) durch biomineralische Einbettung in Nanopartikel

Der Haupt-Lichtsammelkomplex des Fotosystems II (LHCII) setzt sich aus einem Proteinanteil und nicht-kovalent gebundenen Pigmenten – 8 Chlorophyll a, 6 Chlorophyll b und 4 Carotinoide - zusammen. Er assembliert in vivo zu einem Trimer, in dem die Monomereinheiten ebenfalls nicht-kovalent miteinander wechselwirken. Die ausgesprochen hohe Farbstoffdichte und die Tatsache, dass der Komplex rekombinant hergestellt werden kann, machen den LHCII zu einem interessanten Kandidaten für technische Anwendungen wie einer Farbstoffsolarzelle. Allerdings muss hierzu seine thermische Stabilität drastisch erhöht werden.rnDer Einschluss von Proteinen/Enzymen in Silikat erhöht deren Stabilität gegenüber Hitze signifikant. LHCII sollte als erster rekombinanter Membranproteinkomplex mittels kovalent verbundener, polykationischen Sequenzen in Silikat eingeschlossen werden. Hierzu wurde der Komplex auf zwei Weisen polykationisch modifiziert: Auf Genebene wurde die Sequenz des R5-Peptids in den N-terminalen Bereich des LHCP-Gens eingeführt und ein Protokoll zur Überexpression, Rekonstitution und Trimerisierung etabliert. Außerdem wurde eine kovalente Modifikation des trimeren LHCII mit dem Arginin-reichen Protamin über heterobifunktionelle Crosslinker entwickelt. Beide resultierenden LHCII-Derivate waren in der Lage, Silikat autogen zu fällen. Die Stabilisierung der so in Silikat präzipitierten Komplexe war jedoch deutlich geringer als bei nicht-modifizierten Komplexen, die durch eine Spermin-induzierte Copräzipitation eingeschlossenen wurden. Dabei zeigte sich, dass für den Anteil der eingebauten Komplexe und das Ausmaß an Stabilisierung die Größe und klare partikuläre Struktur des Silikats entscheidend ist. Kleine Partikel mit einem Durchmesser von etwa 20 nm führten zu einem Einbau von rund 75 % der Komplexe, und mehr als 80 % des Energietransfers innerhalb des Komplexes blieben erhalten, wenn für 24 Stunden bei 50°C inkubiert wurde. Nicht in Silikat eingeschlossene Komplexe verloren bei 50°C ihren Komplex-internen Energietransfer binnen weniger Minuten. Es war dabei unerheblich, ob die Partikelgröße durch die Wahl des Puffers und des entsprechenden pH-Wertes, oder aber durch Variation des Spermin-zu-Kieselsäure-Verhältnisses erreicht wurde. Wurden die polykationisch veränderten Komplexe in solchen Copräzipitationen verwendet, so erhöhte sich der Anteil an eingebauten Komplexen auf über 90 %, jedoch wurde nur bei der R5-modifizierten Variante vergleichbare Ausmaße an Stabilisierung erreicht. Ein noch höherer Anteil an Komplexen wurde in das Silikatpellet eingebaut, wenn LHCII kovalent mit Silanolgruppen modifiziert wurde (95 %); jedoch war das Ausmaß der Stabilisierung wiederum geringer als bei einer Copräzipitation. Die analysierten Fällungssysteme waren außerdem in der Lage, Titandioxid zu fällen, wobei der Komplex in dieses eingebaut wurde. Allerdings muss das Stabilisierungspotential hier noch untersucht werden. Innerhalb eines Silikatpräzipitats aggregierten die Komplexe nicht, zeigten aber einen inter-trimeren Energietransfer, der sehr wahrscheinlich auf einem Förster Resonanz Mechanismus basiert. rnDies und das hohe Maß an Stabilisierung eröffnen neue Möglichkeiten, rekombinanten LHCII in technischen Applikationen als Lichtsammelkomponente zu verwenden.rn

Oxidative stress and inflammation response after nanoparticle exposure: differences between human lung cell monocultures and an advanced three-dimensional model of the human epithelial airways

Combustion-derived and manufactured nanoparticles (NPs) are known to provoke oxidative stress and inflammatory responses in human lung cells; therefore, they play an important role during the development of adverse health effects. As the lungs are composed of more than 40 different cell types, it is of particular interest to perform toxicological studies with co-cultures systems, rather than with monocultures of only one cell type, to gain a better understanding of complex cellular reactions upon exposure to toxic substances. Monocultures of A549 human epithelial lung cells, human monocyte-derived macrophages and monocyte-derived dendritic cells (MDDCs) as well as triple cell co-cultures consisting of all three cell types were exposed to combustion-derived NPs (diesel exhaust particles) and to manufactured NPs (titanium dioxide and single-walled carbon nanotubes). The penetration of particles into cells was analysed by transmission electron microscopy. The amount of intracellular reactive oxygen species (ROS), the total antioxidant capacity (TAC) and the production of tumour necrosis factor (TNF)-alpha and interleukin (IL)-8 were quantified. The results of the monocultures were summed with an adjustment for the number of each single cell type in the triple cell co-culture. All three particle types were found in all cell and culture types. The production of ROS was induced by all particle types in all cell cultures except in monocultures of MDDCs. The TAC and the (pro-)inflammatory reactions were not statistically significantly increased by particle exposure in any of the cell cultures. Interestingly, in the triple cell co-cultures, the TAC and IL-8 concentrations were lower and the TNF-alpha concentrations were higher than the expected values calculated from the monocultures. The interplay of different lung cell types seems to substantially modulate the oxidative stress and the inflammatory responses after NP exposure.

Biomechanical effects of environmental and engineered particles on human airway smooth muscle cells

The past decade has seen significant increases in combustion-generated ambient particles, which contain a nanosized fraction (less than 100 nm), and even greater increases have occurred in engineered nanoparticles (NPs) propelled by the booming nanotechnology industry. Although inhalation of these particulates has become a public health concern, human health effects and mechanisms of action for NPs are not well understood. Focusing on the human airway smooth muscle cell, here we show that the cellular mechanical function is altered by particulate exposure in a manner that is dependent upon particle material, size and dose. We used Alamar Blue assay to measure cell viability and optical magnetic twisting cytometry to measure cell stiffness and agonist-induced contractility. The eight particle species fell into four categories, based on their respective effect on cell viability and on mechanical function. Cell viability was impaired and cell contractility was decreased by (i) zinc oxide (40-100 nm and less than 44 microm) and copper(II) oxide (less than 50 nm); cell contractility was decreased by (ii) fluorescent polystyrene spheres (40 nm), increased by (iii) welding fumes and unchanged by (iv) diesel exhaust particles, titanium dioxide (25 nm) and copper(II) oxide (less than 5 microm), although in none of these cases was cell viability impaired. Treatment with hydrogen peroxide up to 500 microM did not alter viability or cell mechanics, suggesting that the particle effects are unlikely to be mediated by particle-generated reactive oxygen species. Our results highlight the susceptibility of cellular mechanical function to particulate exposures and suggest that direct exposure of the airway smooth muscle cells to particulates may initiate or aggravate respiratory diseases.

A New Reactor Concept for Efficient Solar-Thermochemical Fuel Production

We describe and analyze the efficiency of a new solar-thermochemical reactor concept, which employs a moving packed bed of reactive particles produce of H-2 or CO from solar energy and H2O or CO2. The packed bed reactor incorporates several features essential to achieving high efficiency: spatial separation of pressures, temperature, and reaction products in the reactor; solid-solid sensible heat recovery between reaction steps; continuous on-sun operation; and direct solar illumination of the working material. Our efficiency analysis includes material thermodynamics and a detailed accounting of energy losses, and demonstrates that vacuum pumping, made possible by the innovative pressure separation approach in our reactor, has a decisive efficiency advantage over inert gas sweeping. We show that in a fully developed system, using CeO2 as a reactive material, the conversion efficiency of solar energy into H-2 and CO at the design point can exceed 30%. The reactor operational flexibility makes it suitable for a wide range of operating conditions, allowing for high efficiency on an annual average basis. The mixture of H-2 and CO, known as synthesis gas, is not only usable as a fuel but is also a universal starting point for the production of synthetic fuels compatible with the existing energy infrastructure. This would make it possible to replace petroleum derivatives used in transportation in the U. S., by using less than 0.7% of the U. S. land area, a roughly two orders of magnitude improvement over mature biofuel approaches. In addition, the packed bed reactor design is flexible and can be adapted to new, better performing reactive materials.

Interaction of fine particles and nanoparticles with red blood cells visualized with advanced microscopic techniques

So far, little is known about the interaction of nanoparticles with lung cells, the entering of nanoparticles, and their transport through the blood stream to other organs. The entering and localization of different nanoparticles consisting of differing materials and of different charges were studied in human red blood cells. As these cells do not have any phagocytic receptors on their surface, and no actinmyosin system, we chose them as a model for nonphagocytic cells to study how nanoparticles penetrate cell membranes. We combined different microscopic techniques to visualize fine and nanoparticles in red blood cells: (I) fluorescent particles were analyzed by laser scanning microscopy combined with digital image restoration, (II) gold particles were analyzed by conventional transmission electron microscopy and energy filtering transmission electron microscopy, and (III) titanium dioxide particles were analyzed by energy filtering transmission electron microscopy. By using these differing microscopic techniques we were able to visualize and detect particles < or = 0.2 microm and nanoparticles in red blood cells. We found that the surface charge and the material of the particles did not influence their entering. These results suggest that particles may penetrate the red blood cell membrane by a still unknown mechanism different from phagocytosis and endocytosis.

Electron energy-loss spectroscopy as a tool for elemental analysis in biological speciments.

A transmission electron microscope (TEM) accessory, the energy filter, enables the establishment of a method for elemental microanalysis, the electron energy-loss spectroscopy (EELS). In conventional TEM, unscattered, elastic, and inelastic scattered electrons contribute to image information. Energy-filtering TEM (EFTEM) allows elemental analysis at the ultrastructural level by using selected inelastic scattered electrons. EELS is an excellent method for elemental microanalysis and nanoanalysis with good sensitivity and accuracy. However, it is a complex method whose potential is seldom completely exploited, especially for biological specimens. In addition to spectral analysis, parallel-EELS, we present two different imaging techniques in this chapter, namely electron spectroscopic imaging (ESI) and image-EELS. We aim to introduce these techniques in this chapter with the elemental microanalysis of titanium. Ultrafine, 22-nm titanium dioxide particles are used in an inhalation study in rats to investigate the distribution of nanoparticles in lung tissue.

Visualization and quantitative analysis of nanoparticles in the respiratory tract by transmission electron microscopy

ABSTRACT: Nanotechnology in its widest sense seeks to exploit the special biophysical and chemical properties of materials at the nanoscale. While the potential technological, diagnostic or therapeutic applications are promising there is a growing body of evidence that the special technological features of nanoparticulate material are associated with biological effects formerly not attributed to the same materials at a larger particle scale. Therefore, studies that address the potential hazards of nanoparticles on biological systems including human health are required. Due to its large surface area the lung is one of the major sites of interaction with inhaled nanoparticles. One of the great challenges of studying particle-lung interactions is the microscopic visualization of nanoparticles within tissues or single cells both in vivo and in vitro. Once a certain type of nanoparticle can be identified unambiguously using microscopic methods it is desirable to quantify the particle distribution within a cell, an organ or the whole organism. Transmission electron microscopy provides an ideal tool to perform qualitative and quantitative analyses of particle-related structural changes of the respiratory tract, to reveal the localization of nanoparticles within tissues and cells and to investigate the 3D nature of nanoparticle-lung interactions.This article provides information on the applicability, advantages and disadvantages of electron microscopic preparation techniques and several advanced transmission electron microscopic methods including conventional, immuno and energy-filtered electron microscopy as well as electron tomography for the visualization of both model nanoparticles (e.g. polystyrene) and technologically relevant nanoparticles (e.g. titanium dioxide). Furthermore, we highlight possibilities to combine light and electron microscopic techniques in a correlative approach. Finally, we demonstrate a formal quantitative, i.e. stereological approach to analyze the distributions of nanoparticles in tissues and cells.This comprehensive article aims to provide a basis for scientists in nanoparticle research to integrate electron microscopic analyses into their study design and to select the appropriate microscopic strategy.

Translocation of particles and inflammatory responses after exposure to fine particles and nanoparticles in an epithelial airway model

ABSTRACT: BACKGROUND: Experimental studies provide evidence that inhaled nanoparticles may translocate over the airspace epithelium and cause increased cellular inflammation. Little is known, however, about the dependence of particle size or material on translocation characteristics, inflammatory response and intracellular localization. RESULTS: Using a triple cell co-culture model of the human airway wall composed of epithelial cells, macrophages and dendritic cells we quantified the entering of fine (1 mum) and nano-sized (0.078 mum) polystyrene particles by laser scanning microscopy. The number distribution of particles within the cell types was significantly different between fine and nano-sized particles suggesting different translocation characteristics. Analysis of the intracellular localization of gold (0.025 mum) and titanium dioxide (0.02-0.03 mum) nanoparticles by energy filtering transmission electron microscopy showed differences in intracellular localization depending on particle composition. Titanium dioxide nanoparticles were detected as single particles without membranes as well as in membrane-bound agglomerations. Gold nanoparticles were found inside the cells as free particles only. The potential of the different particle types (different sizes and different materials) to induce a cellular response was determined by measurements of the tumour necrosis factor-alpha in the supernatants. We measured a 2-3 fold increase of tumour necrosis factor-alpha in the supernatants after applying 1 mum polystyrene particles, gold nanoparticles, but not with polystyrene and titanium dioxide nanoparticles. CONCLUSION: Quantitative laser scanning microscopy provided evidence that the translocation and entering characteristics of particles are size-dependent. Energy filtering transmission electron microscopy showed that the intracellular localization of nanoparticles depends on the particle material. Both particle size and material affect the cellular responses to particle exposure as measured by the generation of tumour necrosis factor-alpha.