Soil thermal diffusivity estimated from data of soil temperature and single soil component properties

Under field conditions, thermal diffusivity can be estimated from soil temperature data but also from the properties of soil components together with their spatial organization. We aimed to determine soil thermal diffusivity from half-hourly temperature measurements in a Rhodic Kanhapludalf, using three calculation procedures (the amplitude ratio, phase lag and Seemann procedures), as well as from soil component properties, for a comparison of procedures and methods. To determine thermal conductivity for short wave periods (one day), the phase lag method was more reliable than the amplitude ratio or the Seemann method, especially in deeper layers, where temperature variations are small. The phase lag method resulted in coherent values of thermal diffusivity. The method using properties of single soil components with the values of thermal conductivity for sandstone and kaolinite resulted in thermal diffusivity values of the same order. In the observed water content range (0.26-0.34 m³ m-3), the average thermal diffusivity was 0.034 m² d-1 in the top layer (0.05-0.15 m) and 0.027 m² d-1 in the subsurface layer (0.15-0.30 m).

Heat pulse line-source method to determine thermal conductivity of consolidated rocks

An instrument designed to measure thermal conductivity of consolidated rocks, dry or saturated, using a transient method is presented. The instrument measures relative values of the thermal conductivity, and it needs calibration to obtain absolute values. The device can be used as heat pulse line source and as continuous heat line source. Two parameters to determine thermal conductivity are proposed: TMAX, in heat pulse line source, and SLOPE, in continuous heat line source. Its performance is better, and the operation simpler, in heat pulse line-source mode with a measuring time of 170 s and a reproducibility better than 2.5%. The sample preparation is very simple on both modes. The performance has been tested with a set of ten rocks with thermal conductivity values between 1.4 and 5.2 W m¿1 K¿1 which covers the usual range for consolidated rocks.

Light induced defects in thermal annealed hydrogenated amorphous silicon

The metastable defects of a-Si:H samples annealed at temperatures in the 300-550°C range have been studied by photothermal deflection spectroscopy (PDS). The light-soaked samples show an increase in optical absorption in the 0.8 to 1.5 eV range. The metastable defect density decreases when the annealing temperature increases, while the defect density increases. This decrease in the metastable defect density shows an almost linear correlation with the decrease in the hydrogen content of the samples, determined by IR transmission spectroscopy and thermal desorption spectroscopy.

Computer-aided procedure for optimization of layer thickness uniformity in thermal evaporation physical vapor deposition chambers for lens coating

A computer-aided method to improve the thickness uniformity attainable when coating multiple substrates inside a thermal evaporation physical vapor deposition unit is presented. The study is developed for the classical spherical (dome-shaped) calotte and also for a plane sector reversible holder setup. This second arrangement is very useful for coating both sides of the substrate, such as antireflection multilayers on lenses. The design of static correcting shutters for both kinds of configurations is also discussed. Some results of using the method are presented as an illustration.

Heat transfer between nanoparticles: Thermal conductance for near-field interactions

We analyze the heat transfer between two nanoparticles separated by a distance lying in the near-field domain in which energy interchange is due to the Coulomb interactions. The thermal conductance is computed by assuming that the particles have charge distributions characterized by fluctuating multipole moments in equilibrium with heat baths at two different temperatures. This quantity follows from the fluctuation-dissipation theorem for the fluctuations of the multipolar moments. We compare the behavior of the conductance as a function of the distance between the particles with the result obtained by means of molecular dynamics simulations. The formalism proposed enables us to provide a comprehensive explanation of the marked growth of the conductance when decreasing the distance between the nanoparticles.

Test-retest reliability of thermal quantitative sensory testing on two sites within the L5 dermatome of the lumbar spine and lower extremity.

INTRODUCTION: Quantitative sensory testing (QST) is widely used in human research to investigate the integrity of the sensory function in patients with pain of neuropathic origin, or other causes such as low back pain. Reliability of QST has been evaluated on both sides of the face, hands and feet as well as on the trunk (Th3-L3). In order to apply these tests on other body-parts such as the lower lumbar spine, it is important first to establish reliability on healthy individuals. The aim of this study was to investigate intra-rater reliability of thermal QST in healthy adults, on two sites within the L5 dermatome of the lumbar spine and lower extremity. METHODS: Test-retest reliability of thermal QST was determined at the L5-level of the lumbar spine and in the same dermatome on the lower extremity in 30 healthy persons under 40 years of age. Results were analyzed using descriptive statistics and intraclass correlation coefficient (ICC). Values were compared to normative data, using Z-transformation. RESULTS: Mean intraindividual differences were small for cold and warm detection thresholds but larger for pain thresholds. ICC values showed excellent reliability for warm detection and heat pain threshold, good-to-excellent reliability for cold pain threshold and fair-to-excellent reliability for cold detection threshold. ICC had large ranges of confidence interval (95%). CONCLUSION: In healthy adults, thermal QST on the lumbar spine and lower extremity demonstrated fair-to-excellent test-retest reliability.

Thermal and back-action noises in dual-sphere gravitational-wave detectors

We study the sensitivity limits of a broadband gravitational-wave detector based on dual resonators such as nested spheres. We determine both the thermal and back-action noises when the resonators displacements are read out with an optomechanical sensor. We analyze the contributions of all mechanical modes, using a new method to deal with the force-displacement transfer functions in the intermediate frequency domain between the two gravitational-wave sensitive modes associated with each resonator. This method gives an accurate estimate of the mechanical response, together with an evaluation of the estimate error. We show that very high sensitivities can be reached on a wide frequency band for realistic parameters in the case of a dual-sphere detector.

Propagation in a thermal graviton background

It is well known that radiative corrections evaluated in nontrivial backgrounds lead to effective dispersion relations which are not Lorentz invariant. Since gravitational interactions increase with energy, gravity-induced radiative corrections could be relevant for the trans-Planckian problem. As a first step to explore this possibility, we compute the one-loop radiative corrections to the self-energy of a scalar particle propagating in a thermal bath of gravitons in Minkowski spacetime. We obtain terms which originate from the thermal bath and which indeed break the Lorentz invariance that possessed the propagator in the vacuum. Rather unexpectedly, however, the terms which break Lorentz invariance vanish in the high three-momentum limit. We also found that the imaginary part, which gives the rate of approach to thermal equilibrium, vanishes at one loop.

MERCURY QUANTIFICATION IN SOILS USING THERMAL DESORPTION AND ATOMIC ABSORPTION SPECTROMETRY: PROPOSAL FOR AN ALTERNATIVE METHOD OF ANALYSIS

Despite the considerable environmental importance of mercury (Hg), given its high toxicity and ability to contaminate large areas via atmospheric deposition, little is known about its activity in soils, especially tropical soils, in comparison with other heavy metals. This lack of information about Hg arises because analytical methods for determination of Hg are more laborious and expensive compared to methods for other heavy metals. The situation is even more precarious regarding speciation of Hg in soils since sequential extraction methods are also inefficient for this metal. The aim of this paper is to present a technique of thermal desorption associated with atomic absorption spectrometry, TDAAS, as an efficient tool for quantitative determination of Hg in soils. The method consists of the release of Hg by heating, followed by its quantification by atomic absorption spectrometry. It was developed by constructing calibration curves in different soil samples based on increasing volumes of standard Hg2+ solutions. Performance, accuracy, precision, and quantification and detection limit parameters were evaluated. No matrix interference was detected. Certified reference samples and comparison with a Direct Mercury Analyzer, DMA (another highly recognized technique), were used in validation of the method, which proved to be accurate and precise.

Thermal evolution of gene expression profiles in Drosophila subobscura

Background: Despite its pervasiveness, the genetic basis of adaptation resulting in variation directly or indirectly related to temperature (climatic) gradients is poorly understood. By using 3-fold replicated laboratory thermal stocks covering much of the physiologically tolerable temperature range for the temperate (i.e., cold tolerant) species Drosophila subobscura we have assessed whole-genome transcriptional responses after three years of thermal adaptation, when the populations had already diverged for inversion frequencies, pre-adult life history components, and morphological traits. Total mRNA from each population was compared to a reference pool mRNA in a standard, highly replicated two-colour competitive hybridization experiment using cDNA microarrays.Results: A total of 306 (6.6%) cDNA clones were identified as 'differentially expressed' (following a false discovery rate correction) after contrasting the two furthest apart thermal selection regimes (i.e., 13°C vs . 22°C), also including four previously reported candidate genes for thermotolerance in Drosophila (Hsp26, Hsp68, Fst, and Treh). On the other hand, correlated patterns of gene expression were similar in cold- and warm-adapted populations. Analysis of functional categories defined by the Gene Ontology project point to an overrepresentation of genes involved in carbohydrate metabolism, nucleic acids metabolism and regulation of transcription among other categories. Although the location of differently expressed genes was approximately at random with respect to chromosomes, a physical mapping of 88 probes to the polytene chromosomes of D. subobscura has shown that a larger than expected number mapped inside inverted chromosomal segments.Conclusion: Our data suggest that a sizeable number of genes appear to be involved in thermal adaptation in Drosophila, with a substantial fraction implicated in metabolism. This apparently illustrates the formidable challenge to understanding the adaptive evolution of complex trait variation. Furthermore, some clustering of genes within inverted chromosomal sections was detected. Disentangling the effects of inversions will be obviously required in any future approach if we want to identify the relevant candidate genes.

Task 6: Material Thermal Input for Iowa Materials, May 2008

The present research project was designed to determine thermal properties, such as coefficient of thermal expansion (CTE) and thermal conductivity, of Iowa concrete pavement materials. These properties are required as input values by the Mechanistic-Empirical Pavement Design Guide (MEPDG). In this project, a literature review was conducted to determine the factors that affect thermal properties of concrete and the existing prediction equations for CTE and thermal conductivity of concrete. CTE tests were performed on various lab and field samples of portland cement concrete (PCC) at the Iowa Department of Transportation and Iowa State University. The variations due to the test procedure, the equipment used, and the consistency of field batch materials were evaluated. The test results showed that the CTE variations due to test procedure and batch consistency were less than 5%, and the variation due to the different equipment was less than 15%. Concrete CTE values were significantly affected by different types of coarse aggregate. The CTE values of Iowa concrete made with limestone+graval, quartzite, dolomite, limestone+dolomite, and limestone were 7.27, 6.86, 6.68, 5.83, and 5.69 microstrain/oF (13.08, 12.35, 12.03, 10.50, and 10.25 microstrain/oC), respectively, which were all higher than the default value of 5.50 microstrain/oF in the MEPDG program. The thermal conductivity of a typical Iowa PCC mix and an asphalt cement concrete (ACC) mix (both with limestone as coarse aggregate) were tested at Concrete Technology Laboratory in Skokie, Illinois. The thermal conductivity was 0.77 Btu/hr•ft•oF (1.33 W/m•K) for PCC and 1.21 Btu/hr•ft•oF (2.09 W/m•K) for ACC, which are different from the default values (1.25 Btu/hr•ft•oF or 2.16 W/m•K for PCC and 0.67 Btu/hr•ft•oF or 1.16 W/m•K for ACC) in the MEPDG program. The investigations onto the CTE of ACC and the effects of concrete materials (such as cementitious material and aggregate types) and mix proportions on concrete thermal conductivity are recommended to be considered in future studies.

Temporal and spatial dynamics of benthic invertebrate communities in an alpine glacier-fed alluvial system

Summary The present thesis work focused on the ecology of benthic invertebrates in the proglacial floodplain of the Rhone in the Swiss Alps. The main glacial Rhone River and a smaller glacial tributary, the Mutt River, joined and entered a braiding multi-thread area. A first part concentrated on the disruption of the longitudinal patterns of environmental conditions and benthic invertebrate fauna in the Rhone by its tributary the Mutt. The Mutt had less harsh environmental conditions, higher taxonomic richness and more abundant zoobenthos compared to the Rhone upstream of the confluence. Although the habitat conditions in the main stream were little modified by the tributary, the fauna was richer and more diverse below the confluence. Colonisation from the Mutt induced the occurrence of faunal elements uncommon of glacial streams in the upper Rhone, where water temperature remains below 4°C. Although the glacial Rhone dominated the system with regard to hydrology and certain environmental conditions, the Mutt tributary has to be seen as the faunal driver of the system. The second part of the study concerned the spatio-temporal differentiation of the habitats and the benthic communities along and across the flood plain. No longitudinal differentiation was found. The spatial transversal differentiation of three habitat types with different environmental characteristics was successfully reflected in the spatial variability of benthic assemblages. This typology separated marginal sites of the flood plain, left bank sites under the influence of the Mutt, and the right bank sites under the influence of the Rh6ne. Faunistic spatial differences were emphasized by the quantitative structure of the fauna, richness, abundances and Simpson index of diversity. Seasonal environmental variability was positively related with Simpson index of diversity and the total richness per site. Low flow conditions were the most favourable season for the fauna and November was characterized by low spatial environmental heterogeneity, high spatial heterogeneity of faunal assemblage, maximum taxonomic richness, a particular taxonomic composition, highest abundances, as well as the highest primary food resources. The third part studied the egg development of three species of Ephemeroptera in the laboratory at 1.5 to 7°C and the ecological implications in the field. Species revealed very contrasting development strategies. Baetis alpinus has a synchronous and efficient egg development, which is faster in warmer habitats, enabling it to exploit short periods of favourable conditions in the floodplain. Ecdyonurus picteti has a very long development time slightly decreasing in warmer conditions. The high degree of individual variation suggests a genetic determination of the degree-days demand. Combined with the glacial local conditions, this strategy leads to an extreme delay of hatching and allows it to develop in very unpredictable habitats. Rhithrogena nivata is the second cold adapted species in Ephemeroptera. The incubation duration is long and success largely depends on the timing of hatching and the discharge conditions. This species is able to exploit extremely unstable and cold habitats where other species are limited by low water temperatures. The fourth part dealt with larval development in different habitats of the floodplain. Addition of data on egg development allowed the description of the life histories of the species from oviposition until emergence. Rhithrogena nivata and loyolaea generally have a two-year development, with the first winter passed as eggs and the second one as larvae. Development of Ecdyonurus picteti is difficult to document but appears to be efficient in a harsh and unpredictable environment. Baetis alpinus was studied separately in four habitats of the floodplain system with contrasting thermal regimes. Differences in success and duration of larval development and in growth rates are emphasised. Subvention mechanisms between habitats by migration of young or grown larvae were demonstrated. Development success and persistence of the populations in the system were thus increased. Emergence was synchronised to the detriment of the optimisation of the adult's size and fecundity. These very different development strategies induce a spatial and temporal distribution in the use of food resources and ecological niches. The last part of this work aimed at the synthesis of the characteristics and the ecological features of three distinct compartments of the system that are the upper Rhone, the Mutt and the floodplain. Their particular role as well as their inter-dependence concerning the structure and the dynamics of the benthic communities was emphasised. Résumé Ce travail de thèse est consacré à l'écologie des invertébrés benthiques dans la zone alluviale proglaciaire du Rhône dans les Alpes suisses. Le Rhône, torrent glaciaire principal, reçoit les eaux de la Mutt, affluent glaciaire secondaire, puis pénètre dans une zone de tressage formée de plusieurs bras. La première partie de l'étude se concentre sur la disruption par la Mutt des processus longitudinaux, tant environnementaux que faunistiques, existants dans le Rhône. Les conditions environnementales régnant dans la Mutt sont moins rudes, la richesse taxonomique plus élevée et le zoobenthos plus abondant que dans le Rhône en amont de la confluence. Bien que les conditions environnementales dans le torrent principal soient peu modifiées par l'affluent, la faune s'avère être plus riche et plus diversifiée en aval de la confluence. La colonisation depuis la Mutt permet l'occurrence de taxons inhabituels dans le Rhône en amont de la confluence, où la température de l'eau se maintient en dessous de 4°C. Bien que le Rhône, torrent glaciaire principal, domine le système du point de vu de l'hydrologie et de certains paramètres environnementaux, l'affluent Mutt doit être considéré comme l'élément structurant la faune dans le système. La deuxième partie concerne la différentiation spatiale et temporelle des habitats et des communautés benthiques à travers la plaine alluviale. Aucune différentiation longitudinale n'a été mise en évidence. La différentiation transversale de trois types d'habitats sur la base des caractéristiques environnementales a été confirmée par la variabilité spatiale de la faune. Cette typologie sépare les sites marginaux de la plaine alluviale, ceux sous l'influence de la Mutt (en rive gauche) et ceux sous l'influence du Rhône amont (en rive droite). Les différences spatiales de la faune sont mises en évidence par la structure quantitative de la faune, la richesse, les abondances et l'indice de diversité de Simpson. La variabilité saisonnière du milieu est positivement liée avec l'indice de diversité de Simpson et la richesse totale par site. L'étiage correspond à la période la plus favorable pour la faune et novembre réunit des conditions de faible hétérogénéité spatiale du milieu, de forte hétérogénéité spatiale de la faune, une richesse taxonomique maximale, une composition faunistique particulière, les abondances ainsi que les ressources primaires les plus élevées. La troisième partie est consacrée à l'étude du développement des oeufs de trois espèces d'Ephémères au laboratoire à des températures de 1.5 à 7°C, ainsi qu'aux implications écologiques sur le terrain. Ces espèces présentent des stratégies de développement très contrastées. Baetis alpinus a un développement synchrone et efficace, plus rapide en milieu plus chaud et lui permettant d'exploiter les courtes périodes de conditions favorables. Ecdyonurus picteti présente une durée de développement très longue, diminuant légèrement dans des conditions plus chaudes. L'importante variation interindividuelle suggère un déterminisme génétique de la durée de développement. Cette stratégie, associée aux conditions locales, conduit à un décalage extrême des éclosions et permet à l'espèce de se développer dans des habitats imprévisibles. Rhithrogena nivata est la seconde espèce d'Ephémères présentant une adaptation au froid. L'incubation des oeufs est longue et son succès dépend de la période des éclosions et des conditions hydrologiques. Cette espèce est capable d'exploiter des habitats extrêmement instables et froids, où la température est facteur limitant pour d'autres espèces. La quatrième partie traite du développement larvaire dans différents habitats de la plaine alluviale. Le développement complet est décrit pour les espèces étudiées de la ponte jusqu'à l'émergence. Rhithrogena nivata et loyolaea atteignent généralement le stade adulte en deux ans, le premier hiver étant passé sous forme d'oeuf et le second sous forme de larve. Le développement de Ecdyonurus picteti est difficile à documenter, mais s'avère cependant efficace dans un environnement rude et imprévisible. Baetis alpinus a été étudié séparément dans quatre habitats de la plaine ayant des régimes thermiques contrastés. La réussite et la durée du développement embryonnaire ainsi que les taux de croissance y sont variables. Des mécanismes de subvention entre habitats sont possibles par la migration de larves juvéniles ou plus développées, augmentant ainsi la réussite du développement et le maintien des populations dans le système. L'émergence devient synchrone, au détriment de l'optimisation de la taille et de la fécondité des adultes. Ces stratégies très différentes induisent une distribution spatiale et temporelle dans l'usage des ressources et des niches écologiques. La dernière partie synthétise les caractéristiques écologiques des trois compartiments du système que sont le Rhône amont, la Mutt et la zone alluviale. Leurs rôles particuliers et leurs interdépendances du point de vue de la structure et de la dynamique des communautés benthiques sont mis en avant.