Caratterizzazione di membrane metalliche e ionomeriche per applicazioni energetiche

The work of this thesis has been focused on the characterization of metallic membranes for the hydrogen purification from steam reforming process and also of perfluorosulphonic acid ionomeric (PFSI) membranes suitable as electrolytes in fuel cell applications. The experimental study of metallic membranes was divided in three sections: synthesis of palladium and silver palladium coatings on porous ceramic support via electroless deposition (ELD), solubility and diffusivity analysis of hydrogen in palladium based alloys (temperature range between 200 and 400 °C up to 12 bar of pressure) and permeation experiments of pure hydrogen and mixtures containing, besides hydrogen, also nitrogen and methane at high temperatures (up to 600 °C) and pressures (up to 10 bar). Sequential deposition of palladium and silver on to porous alumina tubes by ELD technique was carried out using two different procedures: a stirred batch and a continuous flux method. Pure palladium as well as Pd-Ag membranes were produced: the Pd-Ag membranes’ composition is calculated to be close to 77% Pd and 23% Ag by weight which was the target value that correspond to the best performance of the palladium-based alloys. One of the membranes produced showed an infinite selectivity through hydrogen and relatively high permeability value and is suitable for the potential use as a hydrogen separator. The hydrogen sorption in silver palladium alloys was carried out in a gravimetric system on films produced by ELD technique. In the temperature range inspected, up to 400°C, there is still a lack in literature. The experimental data were analyzed with rigorous equations allowing to calculate the enthalpy and entropy values of the Sieverts’ constant; the results were in very good agreement with the extrapolation made with literature data obtained a lower temperature (up to 150 °C). The information obtained in this study would be directly usable in the modeling of hydrogen permeation in Pd-based systems. Pure and mixed gas permeation tests were performed on Pd-based hydrogen selective membranes at operative conditions close to steam-reforming ones. Two membranes (one produced in this work and another produced by NGK Insulators Japan) showed a virtually infinite selectivity and good permeability. Mixture data revealed the existence of non negligible resistances to hydrogen transport in the gas phase. Even if the decrease of the driving force due to polarization concentration phenomena occurs, in principle, in all membrane-based separation systems endowed with high perm-selectivity, an extensive experimental analysis lack, at the moment, in the palladium-based membrane process in literature. Moreover a new procedure has been introduced for the proper comparison of the mass transport resistance in the gas phase and in the membrane. Another object of study was the water vapor sorption and permeation in PFSI membranes with short and long side chains was also studied; moreover the permeation of gases (i.e. He, N2 and O2) in dry and humid conditions was considered. The water vapor sorption showed strong interactions between the hydrophilic groups and the water as revealed from the hysteresis in the sorption-desorption isotherms and thermo gravimetric analysis. The data obtained were used in the modeling of water vapor permeation, that was described as diffusion-reaction of water molecules, and in the humid gases permeation experiments. In the dry gas experiments the permeability and diffusivity was found to increase with temperature and with the equivalent weight (EW) of the membrane. A linear correlation was drawn between the dry gas permeability and the opposite of the equivalent weight of PFSI membranes, based on which the permeability of pure PTFE is retrieved in the limit of high EW. In the other hand O2 ,N2 and He permeability values was found to increase significantly, and in a similar fashion, with water activity. A model that considers the PFSI membrane as a composite matrix with a hydrophilic and a hydrophobic phase was considered allowing to estimate the variation of gas permeability with relative humidity on the basis of the permeability in the dry PFSI membrane and in pure liquid water.

Trasporto di materia in membrane polimeriche e nanocomposite per la separazione di gas

Membrane-based separation processes are acquiring, in the last years, an increasing importance because of their intrinsic energetic and environmental sustainability: some types of polymeric materials, showing adequate perm-selectivity features, appear rather suitable for these applications, because of their relatively low cost and easy processability. In this work have been studied two different types of polymeric membranes, in view of possible applications to the gas separation processes, i.e. Mixed Matrix Membranes (MMMs) and high free volume glassy polymers. Since the early 90’s, it has been understood that the performances of polymeric materials in the field of gas separations show an upper bound in terms of permeability and selectivity: in particular, an increase of permeability is often accompanied by a decrease of selectivity and vice-versa, while several inorganic materials, like zeolites or silica derivates, can overcome this limitation. As a consequence, it has been developed the idea of dispersing inorganic particles in polymeric matrices, in order to obtain membranes with improved perm-selectivity features. In particular, dispersing fumed silica nanoparticles in high free volume glassy polymers improves in all the cases gases and vapours permeability, while the selectivity may either increase or decrease, depending upon material and gas mixture: that effect is due to the capacity of nanoparticles to disrupt the local chain packing, increasing the dimensions of excess free volume elements trapped in the polymer matrix. In this work different kinds of MMMs were fabricated using amorphous Teflon® AF or PTMSP and fumed silica: in all the cases, a considerable increase of solubility, diffusivity and permeability of gases and vapours (n-alkanes, CO2, methanol) was observed, while the selectivity shows a non-monotonous trend with filler fraction. Moreover, the classical models for composites are not able to capture the increase of transport properties due to the silica addition, so it has been necessary to develop and validate an appropriate thermodynamic model that allows to predict correctly the mass transport features of MMMs. In this work, another material, called poly-trimethylsilyl-norbornene (PTMSN) was examined: it is a new generation high free volume glassy polymer that, like PTMSP, shows unusual high permeability and selectivity levels to the more condensable vapours. These two polymer differ each other because PTMSN shows a more pronounced chemical stability, due to its structure double-bond free. For this polymer, a set of Lattice Fluid parameters was estimated, making possible a comparison between experimental and theoretical solubility isotherms for hydrocarbons and alcoholic vapours: the successfully modelling task, based on application of NELF model, offers a reliable alternative to direct sorption measurement, which is extremely time-consuming due to the relevant relaxation phenomena showed by each sorption step. For this material also dilation experiments were performed, in order to quantify its dimensional stability in presence of large size, swelling vapours.

EXAFS-Untersuchungen zur Rolle von Silicium bei der Sorption von umweltrelevanten Schwermetallen (Zn, As, Pb) in Speichermineralen (FeOOH,CSH)

Bei den Sorptions- und Desorptionsmechanismen an Mineraloberflächen ist oft nicht bekannt, durch welchen Mechanismus bestimmte Spurenelemente gebunden werden (Adsorption, Ionenaustausch, Ausfällung). Heterogene Reaktionen an der Fluid/Mineral-Grenzfläche sind im Allgemeinen sehr komplex. Ein Grund dafür ist, dass mehrere Mechanismen simultan ablaufen können. Da verschiedene Reaktionstypen räumlich getrennt ablaufen, d.h. im mikroskopischen Maßstab an unterschiedlichen Reaktionsplätzen, müssen die individuellen Reaktionsmechanismen auf atomarem Maßstab untersucht werden, um die Komplexität der Gesamtreaktion zu verstehen. Mit Hilfe der EXAFS Spektroskopie wurde die Bindungsform und -art der eingelagerten Zink- und Blei-Atome in die synthetische Calciumsilikathydratphase (CSH) und des adsorptiv gebundenen Arsens an der Oberfläche der natürlichen Eisenhydroxidphase bestimmt. Hierbei spielt Silizium eine relevante Rolle für die Immobilisierung von Schwermetallen. In beiden Fällen, in denen das Silizium einerseits als Adsorbat an der Oberfläche der Eisenhydroxidphase und andererseits in die Struktur der Mischphase gebunden vorliegt, trägt es wesentlich zur Form und Art der Bindung der Schwermetalle in die neugebildete Phase bei.

New regularization method for EXAFS analysis: Application to uranium and plutonium sorption onto kaolinite

Die Röntgenabsorptionsspektroskopie (Extended X-ray absorption fine structure (EXAFS) spectroscopy) ist eine wichtige Methode zur Speziation von Schwermetallen in einem weiten Bereich von umweltrelevanten Systemen. Um Strukturparameter wie Koordinationszahl, Atomabstand und Debye-Waller Faktoren für die nächsten Nachbarn eines absorbierenden Atoms zu bestimmen, ist es für experimentelle EXAFS-Spektren üblich, unter Verwendung von Modellstrukturen einen „Least-Squares-Fit“ durchzuführen. Oft können verschiedene Modellstrukturen mit völlig unterschiedlicher chemischer Bedeutung die experimentellen EXAFS-Daten gleich gut beschreiben. Als gute Alternative zum konventionellen Kurven-Fit bietet sich das modifizierte Tikhonov-Regularisationsverfahren an. Ergänzend zur Tikhonov-Standardvariationsmethode enthält der in dieser Arbeit vorgestellte Algorithmus zwei weitere Schritte, nämlich die Anwendung des „Method of Separating Functionals“ und ein Iterationsverfahren mit Filtration im realen Raum. Um das modifizierte Tikhonov-Regularisationsverfahren zu testen und zu bestätigen wurden sowohl simulierte als auch experimentell gemessene EXAFS-Spektren einer kristallinen U(VI)-Verbindung mit bekannter Struktur, nämlich Soddyit (UO2)2SiO4 x 2H2O, untersucht. Die Leistungsfähigkeit dieser neuen Methode zur Auswertung von EXAFS-Spektren wird durch ihre Anwendung auf die Analyse von Proben mit unbekannter Struktur gezeigt, wie sie bei der Sorption von U(VI) bzw. von Pu(III)/Pu(IV) an Kaolinit auftreten. Ziel der Dissertation war es, die immer noch nicht voll ausgeschöpften Möglichkeiten des modifizierten Tikhonov-Regularisationsverfahrens für die Auswertung von EXAFS-Spektren aufzuzeigen. Die Ergebnisse lassen sich in zwei Kategorien einteilen. Die erste beinhaltet die Entwicklung des Tikhonov-Regularisationsverfahrens für die Analyse von EXAFS-Spektren von Mehrkomponentensystemen, insbesondere die Wahl bestimmter Regularisationsparameter und den Einfluss von Mehrfachstreuung, experimentell bedingtem Rauschen, etc. auf die Strukturparameter. Der zweite Teil beinhaltet die Speziation von sorbiertem U(VI) und Pu(III)/Pu(IV) an Kaolinit, basierend auf experimentellen EXAFS-Spektren, die mit Hilfe des modifizierten Tikhonov-Regularisationsverfahren ausgewertet und mit Hilfe konventioneller EXAFS-Analyse durch „Least-Squares-Fit“ bestätigt wurden.

Speziation von Plutonium bei der Sorption und Diffusion in Opalinuston

Die vorliegende Arbeit wurde im Rahmen des BMWi-Verbundprojektes Wechselwirkung und Transport von Aktiniden im natürlichen Tongestein unter Berücksichtigung von Huminstoffen und Tonorganika – Wechselwirkung von Neptunium und Plutonium mit natürlichem Tongestein“ durchgeführt. Um die langfristige Sicherheit der nuklearen Endlager beurteilen zu können, muss eine mögliche Migration der radiotoxischen Abfälle in die Umwelt betrachtet werden. Wegen seiner langen Halbwertszeit (24000 a) leistet Pu-239 einen wesentlichen Beitrag zur Radiotoxizität abgebrannter Kernbrennstoffe in einem Endlager. Das redox-sensitive Pu tritt in Lösung unter umweltrelevanten Bedingungen in den Oxidationsstufen +III bis +VI auf und kann nebeneinander in bis zu vier Oxidationsstufen vorliegen. Tonsteinformationen werden als mögliches Wirtsgestein für Endlager hoch-radioaktiver Abfälle betrachtet. Deshalb sind ausführliche Informationen zur Mobilisierung und Immobilisierung des Pu durch/in das Grundwasser aus einem Endlager von besonderer Bedeutung. In dieser Arbeit wurden neue Erkenntnisse über die Wechselwirkung zwischen Pu und dem natürlichen Tongestein Opalinuston (OPA, Mont Terri, Schweiz) mit Hinblick auf die Endlagerung wärmeentwickelnder radioaktiver Abfälle in einem geologischen Tiefenlager gewonnen.rnDer Fokus der Arbeit lag dabei auf der Bestimmung der Speziation von Pu an der Mineraloberfläche nach Sorptions- und Diffusionsprozessen mittels verschiedener synchrotronbasierter Methoden (µ-XRF, µ-XANES/EXAFS, µ-XRD, XANES/EXAFS). rnDie Wechselwirkung zwischen Pu und OPA wurde zunächst in Batch- und Diffusionsexperimenten in Abhängigkeit verschiedener experimenteller Parameter (u.a. pH, Pu-Oxidationsstufe) untersucht. In Sorptionsexperimenten konnte gezeigt werden, dass einige Parameter (z.B. Temperatur, Huminsäure) einen deutlichen Einfluss auf die Sorption von Pu haben.rnDie Speziationsuntersuchungen wurden zum einen an Pulverproben aus Batchexperimenten und zum anderen an OPA-Dünnschliffen bzw. Diffusionsproben in Abhängigkeit verschiedener experimenteller Parameter durchgeführt. Die EXAFS-Messungen an der Pu LIII-Kante der Pulverproben ergaben, dass eine innersphäriche Sorption von Pu(IV) an Tongestein unabhängig von dem Ausgangsoxidationszustand des Plutoniums in Lösung stattgefunden hat. Durch die Kombination der ortsaufgelösten Methoden wurde erstmalig mittels μ-XRF die Verteilung von Pu und anderen in OPA enthaltenen Elementen bestimmt. µ-XANES-Spektren an Pu-Anreicherungen auf OPA-Dünnschliffen und in Diffusionsproben bestätigen, dass das weniger mobile Pu(IV) die dominierende Spezies nach den Sorptions- und Diffusionsprozessen ist. Darüber hinaus wurde zum ersten Mal ein Diffusionsprofil von Pu in OPA mittels µ-XRF gemessen. Die Speziationsuntersuchungen mittels μ-XANES zeigten, dass das eingesetzte Pu(V) entlang seines Diffusionspfades zunehmend zu Pu(IV) reduziert wird. Mit µ-XRD wurde Illit als dominierende Umgebung, in der Pu angereichert wurde, identifiziert und Siderit als eine redoxaktive Phase auftreten kann. Die Ergebnisse dieser Arbeit zeigen, dass die Sicherheit von OPA als Wirtsgestein eines Endlagers hoch-radioaktiver Abfälle positiv zu bewerten ist. rn

DEVELOPMENT OF A CONCEPTUAL MODEL AND PARAMETERIZATION OF A MATHEMATICAL MODEL FOR SEDIMENT PHOSPHORUS DIAGENESIS, SORPTION AND RELEASE FROM ONONDAGA LAKE SYRACUSE, NEW YORK

Eutrophication is a persistent problem in many fresh water lakes. Delay in lake recovery following reductions in external loading of phosphorus, the limiting nutrient in fresh water ecosystems, is often observed. Models have been created to assist with lake remediation efforts, however, the application of management tools to sediment diagenesis is often neglected due to conceptual and mathematical complexity. SED2K (Chapra et al. 2012) is proposed as a "middle way", offering engineering rigor while being accessible to users. An objective of this research is to further support the development and application SED2K for sediment phosphorus diagenesis and release to the water column of Onondaga Lake. Application of SED2K has been made to eutrophic Lake Alice in Minnesota. The more homogenous sediment characteristics of Lake Alice, compared with the industrially polluted sediment layers of Onondaga Lake, allowed for an invariant rate coefficient to be applied to describe first order decay kinetics of phosphorus. When a similar approach was attempted on Onondaga Lake an invariant rate coefficient failed to simulate the sediment phosphorus profile. Therefore, labile P was accounted for by progressive preservation after burial and a rate coefficient which gradual decreased with depth was applied. In this study, profile sediment samples were chemically extracted into five operationally-defined fractions: CaCO3-P, Fe/Al-P, Biogenic-P, Ca Mineral-P and Residual-P. Chemical fractionation data, from this study, showed that preservation is not the only mechanism by which phosphorus may be maintained in a non-reactive state in the profile. Sorption has been shown to contribute substantially to P burial within the profile. A new kinetic approach involving partitioning of P into process based fractions is applied here. Results from this approach indicate that labile P (Ca Mineral and Organic P) is contributing to internal P loading to Onondaga Lake, through diagenesis and diffusion to the water column, while the sorbed P fraction (Fe/Al-P and CaCO3-P) is remaining consistent. Sediment profile concentrations of labile and total phosphorus at time of deposition were also modeled and compared with current labile and total phosphorus, to quantify the extent to which remaining phosphorus which will continue to contribute to internal P loading and influence the trophic status of Onondaga Lake. Results presented here also allowed for estimation of the depth of the active sediment layer and the attendant response time as well as the sediment burden of labile P and associated efflux.

Identifiability of diffusion and sorption parameters from in situ diffusion experiments by using simultaneously tracer dilution and claystone data

In situ diffusion experiments are performed in geological formations at underground research laboratories to overcome the limitations of laboratory diffusion experiments and investigate scale effects. Tracer concentrations are monitored at the injection interval during the experiment (dilution data) and measured from host rock samples around the injection interval at the end of the experiment (overcoring data). Diffusion and sorption parameters are derived from the inverse numerical modeling of the measured tracer data. The identifiability and the uncertainties of tritium and Na-22(+) diffusion and sorption parameters are studied here by synthetic experiments having the same characteristics as the in situ diffusion and retention (DR) experiment performed on Opalinus Clay. Contrary to previous identifiability analyses of in situ diffusion experiments, which used either dilution or overcoring data at approximate locations, our analysis of the parameter identifiability relies simultaneously on dilution and overcoring data, accounts for the actual position of the overcoring samples in the claystone, uses realistic values of the standard deviation of the measurement errors, relies on model identification criteria to select the most appropriate hypothesis about the existence of a borehole disturbed zone and addresses the effect of errors in the location of the sampling profiles. The simultaneous use of dilution and overcoring data provides accurate parameter estimates in the presence of measurement errors, allows the identification of the right hypothesis about the borehole disturbed zone and diminishes other model uncertainties such as those caused by errors in the volume of the circulation system and the effective diffusion coefficient of the filter. The proper interpretation of the experiment requires the right hypothesis about the borehole disturbed zone. A wrong assumption leads to large estimation errors. The use of model identification criteria helps in the selection of the best model. Small errors in the depth of the overcoring samples lead to large parameter estimation errors. Therefore, attention should be paid to minimize the errors in positioning the depth of the samples. The results of the identifiability analysis do not depend on the particular realization of random numbers. (C) 2012 Elsevier B.V. All rights reserved.

THE CHLOREX TREATABILITY STUDY: ENVIRONMENTAL FATE IN FACULTATIVE ANAEROBIC AND AEROBIC WASTE STABILIZATION PONDS (BIODEGRADATION, VOLATILIZATION, SORPTION, PRIORITY POLLUTANTS)

The efficacy of waste stabilization lagoons for the treatment of five priority pollutants and two widely used commercial compounds was evaluated in laboratory model ponds. Three ponds were designed to simulate a primary anaerobic lagoon, a secondary facultative lagoon, and a tertiary aerobic lagoon. Biodegradation, volatilization, and sorption losses were quantified for bis(2-chloroethyl) ether, benzene, toluene, naphthalene, phenanthrene, ethylene glycol, and ethylene glycol monoethyl ether. A statistical model using a log normal transformation indicated biodegradation of bis(2-chloroethyl) ether followed first-order kinetics. Additionally, multiple regression analysis indicated biochemical oxygen demand was the water quality variable most highly correlated with bis(2-chloroethyl) ether effluent concentration. ^

Composition and sorption capacity of oceanic and marine ferromanganese nodules

Experimental data obtained show that oceanic and marine ferromanganese nodules and crusts are natural ion-exchangers. Exchange capacity of oceanic ferromanganese aggregates is much higher than that of shallow-water marine ones, whereas reactivities of exchange cations (Na, K, Ca, and Mg) are almost equal in both.

Polpa de guavira (Campomanesia cambessedeana Berg) desidratada em spray dryer: efeitos das condições de processo e composição da alimentação nas propriedades físico químicas e atividade antioxidante

O objetivo desse trabalho foi obter polpa de guavira desidratada por atomização, utilizando maltodextrina ou goma arábica como agentes carreadores. Inicialmente, avaliou-se a influência das condições de processo, temperatura do ar de secagem (130, 155 e 180) °C e vazão volumétrica da mistura (20 e 40) mL/min, o tipo e concentração de agente carreador (10 e 20) % nas características físicas, físico-químicas e atividade antioxidante do produto obtido. As propriedades analisadas foram umidade, atividade de água, higroscopicidade, solubilidade, cor, distribuição e tamanho médio de partículas, morfologia, compostos fenólicos totais e atividade antioxidante. A temperatura do ar de secagem e a vazão volumétrica de alimentação influenciaram significativamente todas as propriedades da guavira em pó. A umidade e atividade de água apresentaram os menores valores na temperatura intermediária, independentemente do tipo e concentração do carreador usado. A solubilidade das amostras adicionadas de maltodextrina foram superiores às amostras com goma arábica. O aumento da concentração de agente carreador, em geral, proporcionou um aumento no parâmetro L* e diminuição dos parâmetros a* e b*, tornando as amostras mais claras e reduzindo as tonalidades vermelha e amarela. A guavira em pó apresentou coloração próxima do amarelo e marrom, com grande variação nos parâmetros de cor C* e H* em função das diferentes condições de secagem. A distribuição do tamanho de partículas não teve um padrão definido e o tamanho médio das amostras com maltodextrina foram maiores do que as com goma arábica para a temperatura do ar a 130 °C. No entanto, para as outras temperaturas (155 e 180) °C não houve um comportamento específico do tamanho das partículas em função da vazão de alimentação, tipo e ou concentração de agente carreador. A análise de microscopia eletrônica de varredura permitiu observar que as partículas obtidas tanto com maltodextrina como goma arábica apresentaram formato esférico, superfície rugosa e com adesão de partículas menores nas de maior tamanho, sendo que a superfície das partículas com goma arábica também apresentaram concavidades. A atividade antioxidante foi superior quando utilizada a temperatura de secagem intermediária. A partir das condições selecionadas na primeira etapa (temperatura do ar de 155 °C, vazão volumétrica da mistura de 40 mL/min e 10% de maltodextrina ou goma arábica) a polpa de guavira em pó foi caracterizada quanto a temperatura de transição vítrea, as isotermas de adsorção e a estabilidade à estocagem do ácido ascórbico, compostos fenólicos totais e da atividade antioxidante da polpa de guavira em pó produzida por spray drying ao longo de 120 dias. As temperaturas de transição vítrea foram de (25,2 ± 2,7 °C e 31,4 ± 0,4) °C para os pós produzidos com goma arábica e maltodextrina, respectivamente. O modelo de BET apresentou ajuste muito bom (R2>0,99) para descrever o comportamento de sorção de água das amostras nas temperaturas de (20, 30 e 40) °C. A polpa de guavira em pó produzida com goma arábica apresentou maior adsorção de água do que as amostras obtidas com maltodextrina. No estudo da estabilidade, as amostras foram acondicionadas em embalagem de polietileno laminado e armazenadas a 25 °C e umidade relativa de 75%. A embalagem de polietileno laminado foi eficiente na manutenção do teor de ácido ascórbico e atividade antioxidante da guavira em pó por um período de 120 dias, independente do carreador adicionado. O teor de compostos fenólicos para a guavira em pó com goma arábica apresentou uma redução nos primeiros 22 dias, contudo a amostra com maltodextrina manteve-se estável durante 120 dias de armazenamento.

Estudo de equilíbrio e cinética da biossorção de cobre (II) por Rhizopus Microsporus.

A poluição relacionada a metais pesados tem recebido uma atenção especial devido a sua alta toxicidade, não biodegradabilidade e tendência de acumular-se na cadeia alimentar. Apesar disso, metais pesados também são considerados recursos valiosos, portanto a sua remoção em conjunto com a sua recuperação torna-se ainda mais importante. Este caso aplica-se aos rejeitos de mineração de cobre, os quais oferecem a possibilidade de recuperação do metal e de sua contenção de maneira segura do meio ambiente. Tais rejeitos se caracterizam por ocuparem enormes áreas inundadas e abrigarem soluções diluídas de cobre (II), porém, muitas vezes, acima dos limites seguros. Diversos processos tradicionais de tratamento mostram-se disponíveis para remover o cobre de tais soluções, no entanto, em certas aplicações eles podem ser ineficientes ou muito onerosos. Nesse contexto, a biossorção é uma alternativa interessante. Nesse processo, certos microrganismos, como fungos, bactérias e algas, ligam-se passivamente ao cobre na forma íons ou outras moléculas em soluções. No presente trabalho foi avaliado o potencial de biossorção de íons cobre (II) pela biomassa do fungo Rhizopus microsporus, coletado e isolado da área de rejeitos da Mina do Sossego, na região norte do Brasil. Isotermas de biossorção foram determinadas experimentalmente em bateladas sob temperatura de 25°C, agitação de 150 rpm, concentração de biomassa de 2,0 a 2,5 g/L e tempo de contato mínimo de 4 horas. O pH mostrou ser um fator importante no equilíbrio da biossorção, sendo o valor máximo da capacidade de biossorção de 33,12 mg de cobre / g biomassa encontrado em pH 6. Valores sucessivamente menores são encontrados pela acidificação da solução, sendo o pH 1 considerado adequado para o processo de dessorção, correspondendo a uma capacidade de biossorção de 1,95 mg/g. Modelos de adsorção de Langmuir e de Freundlich ajustaram-se adequadamente às isotermas tanto com pH controlado quanto não controlado. Foi constatado que a troca iônica é um dos mecanismos envolvidos na biossorção do cobre com Rhizopus microsporus. Tanto o modelo de pseudo-primeira ordem quanto o de pseudo-segunda ordem ajustaram-se aos dados cinéticos da biossorção, sendo que o equilíbrio ocorre em aproximadamente 4 horas. A biomassa conservou a capacidade de biossorção ao operar repetidamente em três ciclos de sorção-dessorção. A biomassa viável e a morta não apresentaram diferença estatisticamente significativa na capacidade de biossorção.

High-Resolution N2 Adsorption Isotherms at 77.4 K: Critical Effect of the He Used During Calibration

Accurate characterization of the microporous structure in porous solids is of paramount importance for several applications such as energy and gas storage, nanoconfinement reactions, and so on. Among the different techniques for precise textural characterization, high-precision gas adsorption measurement of probe molecules at cryogenic temperatures (e.g., N2 at 77.4 K and Ar at 87.3 K) is the most widely used, after appropriate calibration of the sample holder with a probe gas, which does not experience physisorption processes. Although traditionally helium has been considered not to be adsorbed in porous solids at cryogenic temperatures, here we show that even at 77.4 K (high above its boiling temperature, 4 K) the use of He in the calibration step can give rise to erroneous interpretations when narrow micropores/constrictions are present.

Clay-supported graphene materials: application to hydrogen storage

The present work refers to clay–graphene nanomaterials prepared by a green way using caramel from sucrose and two types of natural clays (montmorillonite and sepiolite) as precursors, with the aim of evaluating their potential use in hydrogen storage. The impregnation of the clay substrates by caramel in aqueous media, followed by a thermal treatment in the absence of oxygen of these clay–caramel intermediates gives rise to graphene-like materials, which remain strongly bound to the silicate support. The nature of the resulting materials was characterized by different techniques such as XRD, Raman spectroscopy and TEM, as well as by adsorption isotherms of N2, CO2 and H2O. These carbon–clay nanocomposites can act as adsorbents for hydrogen storage, achieving, at 298 K and 20 MPa, over 0.1 wt% of hydrogen adsorption excess related to the total mass of the system, and a maximum value close to 0.4 wt% of hydrogen specifically related to the carbon mass. The very high isosteric heat for hydrogen sorption determined from adsorption isotherms at different temperatures (14.5 kJ mol−1) fits well with the theoretical values available for hydrogen storage on materials that show a strong stabilization of the H2 molecule upon adsorption.