Investigation on reproduction process in two species of crab, Eriphia sebana and Ocypode saratan in the intertidal zone of Chabahar area

The present study with headline investigation on reproduction in two species of crab Eriphia sebana and Ocypode saratan was carried out in the intertidal zone of Chabahar in thirteen month from December 2004 to December 2005. Checked samplings have been taken, 45 number Crab monthly from any four stations by manual or use trap. During this study the following subjects were measured: temperature range and salinity, measurable coast granule, determination of sex ratio, relations carapace width with carapace length, Carapace width with total body weight, Gonad weight, gonadosomatic index, condition factor, gastrosomatic index, investigation content in stomach, LM50, growth parameters, plenty distribution length and width and gonad weight and total body weight. Studied on measurable coast granule were expressed that Ocypode saratan in Desalination station, were nest in soils equable sand and this quantity were confirmed in Pozm station. Sex ratio were assign in desalination area and Pozm M: F 0/44:0/56 and in Tiss and Chabahar M:F 0/45:0/55. Carapace length and carapace width (cm) and body weight (g) Furthest were designated in Ocypode saratan within carapace width sequential: In female: 5/42-6/15-105/13 and in male: 5/53-6/25-108/91 and in Eriphia sebana within Tiss area sequential: in female: 5/12-5/94-110/21 and in male 5/14-60/01-114/37. Have been linear relationship between carapace length and carapace width and equaled CW=aCL+b. Weight growth in two species were be modal and equaled BW=aCLb And increased crab weight by built up carapace width. Maximum gonad weight in Ocypode saratan within Desalination area in female have been outcome 3/39 and in male 0/84g and in Eriphia sebana extreme within Tiss during may in female were be 4/18 and in male 1/1g. Stomach content in Eriphia sebana were involved a black until half-purplish liquid and yellowish in Ocypode saratan. Stomach contents identifiable were being in four groups: Molluscoid, Crustacean, Plankton and Fish. Carapace width during the first year of maturation have been LM50:3/77 in Desalination area and LM50:3/92 in Pozm for Ocypode saratan and LM50:4/26 in Tiss and LM50:4/62 in Chabahar. Ability spawning in Eriphia sebana within Tiss has been CW=4/17cm and in Ocypode saratan within Desalination area CW=4/23cm. Maximun value of Loo for Eriphia sebana was equal 59/67 and growth factor K=0/68 within Tiss and Loo =61/64, K=0/65 for Ocypode saratan within Desalination area. Maximun GSI and GI have been within Desalination area and Tiss and minimum within Pozm and Chabahar. The maturity stages of two species were classifed into six stages. Review on GSI, CF have been showed that relation with temperature and salinity and definer in two species have been spawned in two period that Maximun in spring premier than autumn.

Management and Analysis of Unstructured Construction Data Types

Compared with structured data sources that are usually stored and analyzed in spreadsheets, relational databases, and single data tables, unstructured construction data sources such as text documents, site images, web pages, and project schedules have been less intensively studied due to additional challenges in data preparation, representation, and analysis. In this paper, our vision for data management and mining addressing such challenges are presented, together with related research results from previous work, as well as our recent developments of data mining on text-based, web-based, image-based, and network-based construction databases.

Identification of factors affecting the growth and survival of the settling Japanese flounder larvae, Paralichthys olivaceus

A series of experiments were conducted to identify the factors that affected the growth and survival of the settling flounder larvae Paralichthys olivaceus. Settling larvae 24 days after hatching (DAH) were reared in 10-l experimental tanks up to 40 DAH, and two of the following factors were changed as controlled factors in each experiment: light regime (24L:0D or 12L:12D), prey density (1500, 3000, or 5000 Artemia l(-1)), shelter (sand or no sand) and stocking density (5, 10, or 15 fish l(-1)). Early settling larvae (24-35 DAH) experienced little mortality (less than 10% of the overall mortality) that was not significantly affected by above factors. In contrast, late settling larvae (36-40 DAH) suffered high cannibalistic mortality which was significantly influenced by each of the above factors. Larvae experienced significantly lower mortality at 10 fish l(-1) level than at other densities. Larvae at 15 fish l(-1) level had higher mortality than at 5 fish l(-1) when all other factors were identical. Larvae at 3000 and 5000 Artemia l(-1) treatments survived significantly better than at 1500 Artemia l(-1), but no significant differences in larval mortality were found between the two higher densities. Larvae suffered higher mortality at low prey density or at the absence of sand when they were exposed to longer photoperiod. Low stocking density significantly improved the growth of the settling larvae. The average daily instantaneous growth rate (G) at 5 and 15 fish l(-1) treatments were 0.050 and 0.034, with the coefficient of variation (CV) in final length at 16.4 and 23.5, respectively. Daily instantaneous growth rate increased significantly from 0.033 in the 1500 Artemia l(-1) to 0.041 and 0.045 in the 3000 and 5000 Artennia l(-1), respectively, but no significant difference in larval growth existed between the two higher prey densities. These findings suggested that the optimal prey density for growth and survival of the settling flounder larvae at a stocking density of 5 - 15 fish l(-1) was around 3000 Artemia l(-1) . Larvae that were exposed to 24L showed 20% increase in growth ( G = 0.046, CV = 18.7) than those exposed to 12L ( G = 0.037, CV = 20.5). Longer exposure to light significantly improved larval growth, provided sufficient food was available. Sand substrate did not show significant effects on larval growth, possibly because the larvae spent most of the time swimming or feeding in the water column during this stage. (C) 2003 Elsevier Science B.V. All rights reserved.

Simultaneous enumeration of diatom, protozoa and meiobenthos from marine sediments using Ludox-QPS method

The Ludox-QPS method is a newly developed technique, which combines the Ludox HS 40 density centrifugation and quantitative protargol stain, to enumerate marine ciliates with good taxonomic resolution. We tested the method for simultaneous enumeration of diatoms, protozoa and meiobenthos and compared its extraction efficiency for meiobenthos with that of the routine Ludox-TM centrifugation and a modified protocol using Ludox HS 40. We conducted the evaluation with a sample size of 8.3 ml each from sandy, muddy-sand and muddy sediments collected from the intertidal area of the Yellow Sea in summer 2006 and spring 2007. The Ludox-QPS method not only produced high extraction efficiencies of 97 +/- 1.3% for diatoms and 97.6 +/- 0.8% for ciliates, indicating a reliable enumeration for eukaryotic microbenthos, but also produced excellent extraction efficiencies of on average 97.3% for total meiobenthos, 97.9% for nematodes and 97.8% for copepods from sands, muddy sands and mud. By contrast, the routine Ludox-TM centrifugation obtained only about 74% of total meiobenthos abundance with one extraction cycle, and the modified Ludox HS 40 centrifugation yielded on average 93% of total meiobenthos: 89.4 +/- 2.0% from sands, 93 +/- 4.1% from muddy sands and 97.1 +/- 3.0% from mud. Apart from the sediment type, sample volume was another important factor affecting the extraction efficiency for meiobenthos. The extraction rate was increased to about 96.4% when using the same modified Ludox centrifugation for a 4 ml sediment sample. Besides the excellent extraction efficiency, the Ludox-QPS method obtained higher abundances of meiobenthos, in particular nematodes, than the routine Ludox centrifugation, which frequently resulted in an uncertain loss of small meiobenthos during the sieving process. Statistical analyses demonstrated that there were no significant differences between the meiobenthos communities revealed by the Ludox-QPS method and the modified Ludox HS 40 centrifugation, showing the high efficiency of the Ludox-QPS method for simultaneous enumeration of diatom, protozoa and meiobenthos. Moreover, the comparatively high taxonomic resolution of the method, especially for diatoms and ciliates, makes it feasible to investigate microbial ecology at community level.

Modelling the fluid dynamics and coupled phenomena in arc weld pools

A 3D model of melt pool created by a moving arc type heat sources has been developed. The model solves the equations of turbulent fluid flow, heat transfer and electromagnetic field to demonstrate the flow behaviour phase-change in the pool. The coupled effects of buoyancy, capillary (Marangoni) and electromagnetic (Lorentz) forces are included within an unstructured finite volume mesh environment. The movement of the welding arc along the workpiece is accomplished via a moving co-ordinator system. Additionally a method enabling movement of the weld pool surface by fluid convection is presented whereby the mesh in the liquid region is allowed to move through a free surface. The surface grid lines move to restore equilibrium at the end of each computational time step and interior grid points then adjust following the solution of a Laplace equation.

The potential use of mapped extent and distribution of habitats as indicators of Good Environmental Status (GES)

The Healthy and Biologically Diverse Seas Evidence Group (HBDSEG) has been tasked with providing the technical advice for the implementation of the Marine Strategy Framework Directive (MSFD) with respect to descriptors linked to biodiversity. A workshop was held in London to address one of the Research and Development (R&D) proposals entitled: ‘Mapping the extent and distribution of habitats using acoustic and remote techniques, relevant to indicators for area/extent/habitat loss.’ The aim of the workshop was to identify, define and assess the feasibility of potential indicators of benthic habitat distribution and extent, and identify the R&D work which could be required to fully develop these indicators. The main points that came out of the workshop were: (i) There are many technical aspects of marine habitat mapping that still need to be resolved if cost-effective spatial indicators are to be developed. Many of the technical aspects that need addressing surround issues of consistency, confidence and repeatability. These areas should be tackled by the JNCC Habitat Mapping and Classification Working Group and the HBDSEG Seabed Mapping Working Group. (ii) There is a need for benthic ecologists (through the HBDSEG Benthic Habitats Subgroup and the JNCC Marine Indicators Group) to finalise the list of habitats for which extent and/or distribution indicators should be considered for development, building upon the recommendations from this report. When reviewing the list of indicators, benthic habitats could also be distinguished into those habitats that are defined/determined primarily by physical parameters (although including biological assemblages) (e.g. subtidal shallow sand) and those defined primarily by their biological assemblage (e.g. seagrass beds). This distinction is important as some anthropogenic pressures may influence the biological component of the ecosystem despite not having a quantifiable effect on the physical habitat distribution/extent. (iii) The scale and variety of UK benthic habitats makes any attempt to undertake comprehensive direct mapping exercises prohibitively expensive (especially where there is a need for repeat surveys for assessment). There is a clear need therefore to develop a risk-based approach that uses indirect indicators (e.g. modelling), such as habitats at risk from pressures caused by current human activities, to develop priorities for information gathering. The next steps that came out of the workshop were: (i) A combined approach should be developed by the JNCC Marine Indicators Group together with the HBDSEG Benthic Habitats Subgroup, which will compile and ultimately synthesise all the criteria used by the three different groups from the workshop. The agreed combined approach will be used to undertake a final review of the habitats considered during the workshop, and to evaluate any remaining habitats in order to produce a list of habitats for indicator development for which extent and/or distribution indicators could be appropriate. (ii) The points of advice raised at this workshop, alongside the combined approach aforementioned, and the final list of habitats for extent and/or distribution indicator development will be used to develop a prioritised list of actions to inform the next round of R&D proposals for benthic habitat indicator development in 2014. This will be done through technical discussions within JNCC and the relevant HBDSEG Subgroups. The preparation of recommendations by these groups should take into account existing work programmes, and consider the limited resources available to undertake any further R&D work.

Fighting for shells: how private information about resource value changes hermit crab pre-fight displays and escalated fight behaviour

Pre-fight displays typically provide honest, but sometimes dishonest, information about resource holding potential and may be influenced by assessment of resource value and hence motivation to acquire the resource. These assessments of potential costs and benefits are also predicted to influence escalated fight behaviour. This is examined in shell exchange contests of hermit crabs in which we establish an information asymmetry about a particularly poor quality shell. The poor shell was created by gluing sand to the interior whereas control shells lacked sand and the low value of the poor shell could not be accurately assessed by the opponent. Crabs in the poor shell showed changes in the use of pre-fight displays, apparently to increase the chances of swapping shells. When the fights escalated, crabs in poor shells fought harder if they took the role of attacker but gave up quickly if in the defender role. These tactics appear to be adaptive but do not result in a major shift in the roles taken or outcome. We thus link resource assessment with pre-fight displays, the roles taken, tactics used during escalation and the outcome of these contests.

Geological fakes and frauds

Some geological fakes and frauds are carried out solely for financial gain (mining fraud), whereas others maybe have increasing aesthetic appeal (faked fossils) or academic advancement (fabricated data) as their motive. All types of geological fake or fraud can be ingenious and sophisticated, as demonstrated in this article. Fake gems, faked fossils and mining fraud are common examples where monetary profit is to blame: nonetheless these may impact both scientific theory and the reputation of geologists and Earth scientists. The substitution or fabrication of both physical and intellectual data also occurs for no direct financial gain, such as career advancement or establishment of belief (e.g. evolution vs. creationism). Knowledge of such fakes and frauds may assist in spotting undetected geological crimes: application of geoforensic techniques helps the scientific community to detect such activity, which ultimately undermines scientific integrity.

The effect of construction pattern and unit interlock on the structural behaviour of block pavements

The maintenance or even replacement of cracked pavements requires considerable financial resources and puts a large burden on the budgets of local councils. In addition to these costs, local councils also face liability claims arising from uneven or cracked pedestrian pavements. These currently cost the Manchester City Council and Preston City Council around £6 million a year each. Design procedures are empirical. A better understanding of the interaction between paving blocks, bedding sand and subbase was necessary in order to determine the mode of failure of pavements under load. Increasing applied stress was found to mobilise ‘‘rotational interlock’’, providing increased pavement stiffness and thus increased load dissipation resulting in lower transmitted stress on the subgrade. The indications from the literature
review were that pavements are designed to fail by excessive deformation and that paving blocks remained uncracked at failure. This was confirmed with experimental data which was obtained from tests on segments of pavements that were laid/constructed in a purpose built test frame in the laboratory.

Influence of nanoclays on mechanical and barrier properties of hydrogenated acrylonitrile butadiene rubber nanocomposites

In this research, two different methods have been investigated for optimising the preparation of hydrogenated acrylonitrile butadiene rubber/clay nanocomposites. Commercially available organoclay (Cloisite 20A) has been considered for the preparation of rubber nanocomposites. A detailed analysis has been made to investigate the morphological structure and mechanical behaviour at room temperature and at elevated temperature. Also the influence of organoclays on permeability has been studied. Structural analysis indicates very good dispersion for a low loading of 5 parts per hundred (phr) amount of nanoclays. Significant improvements in mechanical properties have been observed with the addition of organoclays at both room and elevated temperatures. Even with the low level of addition of nanoclays, there was a remarkable reduction in permeability. © Institute of Materials, Minerals and Mining 2011.

Hard coatings on elastomers for reduced permeability and increased wear resistance

In this study, three different elastomers, namely hydrogenated nitrile butadiene rubber, fluoroelastomer and silicone, have been subjected to two different hard metallised coatings by ion implantation process. The three different elastomers are commonly used in various seal applications, where reduced wear and gas permeability are essential in maintaining seal performance and functionality. Samples of these rubbers have been coated with chromium coating in one set of tests. In the second set of tests, samples of elastomers have been coated with tungsten carbide coating being deposited on all the three different elastomers. Wear, gas permeability and mechanical behaviour of the coated samples were compared with each other and with the control uncoated elastomers. All the coated samples showed good reduction in gas permeability. With the use of metallised coatings, there has been improved resistance to wear in all the coated samples. Adhesion strength and effect of coating on the elastomer have been investigated by mechanical testing. Mechanical tests revealed good adhesion of metal coatings on all the rubber samples, and there was no detrimental effect on the mechanical properties after coating. © 2012 Institute of Materials, Minerals and Mining.

Reusability assessment of thermoset polymeric composite wastes as reinforcement and filler replacement for polymer concrete materials

The development and applications of thermoset polymeric composites, namely fiber reinforced polymers (FRP), have shifted in the last decades more and more into the mass market [1]. Production and consume have increased tremendously mainly for the construction, transportation and automobile sectors [2, 3]. Although the many successful uses of thermoset composite materials, recycling process of byproducts and end of lifecycle products constitutes a more difficult issue. The perceived lack of recyclability of composite materials is now increasingly important and seen as a key barrier to the development or even continued used of these materials in some markets.

Biodiversity of amoebae and amoebae-resisting bacteria in a drinking water treatment plant

The complex ecology of free-living amoebae (FLA) and their role in spreading pathogenic microorganisms through water systems have recently raised considerable interest. In this study, we investigated the presence of FLA and amoebae-resisting bacteria (ARB) at various stages of a drinking water plant fed with river water. We isolated various amoebal species from the river and from several points within the plant, mostly at early steps of water treatment. Echinamoeba- and Hartmannella-related amoebae were mainly recovered in the drinking water plant whereas Acanthamoeba- and Naegleria-related amoebae were recovered from the river water and the sand filtration units. Some FLA isolates were recovered immediately after the ozonation step, thus suggesting resistance of these microorganisms to this disinfection procedure. A bacterial isolate related to Mycobacterium mucogenicum was recovered from an Echinamoeba-related amoeba isolated from ozone-treated water. Various other ARB were recovered using co-culture with axenic Acanthamoeba castellanii, including mycobacteria, legionella, Chlamydia-like organisms and various proteobacteria. Noteworthy, a new Parachlamydia acanthamoebae strain was recovered from river water and from granular activated carbon (GAC) biofilm. As amoebae mainly multiply in sand and GAC filters, optimization of filter backwash procedures probably offers a possibility to better control these protists and the risk associated with their intracellular hosts

Grain refinement studies on Mg and Mg-Al based alloys

Demand on magnesium and its alloys is increased significantly in the automotive industry because of their great potential in reducing the weight of components, thus resulting in improvement in fuel efficiency of the vehicle. To date, most of Mg products have been fabricated by casting, especially, by die-casting because of its high productivity, suitable strength, acceptable quality & dimensional accuracy and the components produced through sand, gravity and low pressure die casting are small extent. In fact, higher solidification rate is possible only in high pressure die casting, which results in finer grain size. However, achieving high cooling rate in gravity casting using sand and permanent moulds is a difficult task, which ends with a coarser grain nature and exhibit poor mechanical properties, which is an important aspect of the performance in industrial applications. Grain refinement is technologically attractive because it generally does not adversely affect ductility and toughness, contrary to most other strengthening methods. Therefore formation of fine grain structure in these castings is crucial, in order to improve the mechanical properties of these cast components. Therefore, the present investigation is “GRAIN REFINEMENT STUDIES ON Mg AND Mg-Al BASED ALLOYS”. The primary objective of this present investigation is to study the effect of various grain refining inoculants (Al-4B, Al- 5TiB2 master alloys, Al4C3, Charcoal particles) on Pure Mg and Mg-Al alloys such as AZ31, AZ91 and study their grain refining mechanisms. The second objective of this work is to study the effect of superheating process on the grain size of AZ31, AZ91 Mg alloys with and without inoculants addition. In addition, to study the effect of grain refinement on the mechanical properties of Mg and Mg-Al alloys. The thesis is well organized with seven chapters and the details of the studies are given below in detail.