Estudo de revestimentos inorgânicos com inibidor de corrosão aplicado na superfície do concreto

The corrosive phenomenon on reinforced concrete structures is one of the most founded pathologies on the coastal area. With the objective to prevent the process development, or even, retard its beginning, it was studied the application of inorganic covering over concrete surfaces, after its cure, as well as, evaluate the efficiency of the covering applied on the concrete in reducing its porosity of concrete preventing the entrance of aggressive agents to preserve the integrity of the existing armor inside it, comparing the result obtained with the body-of-proof reference, that didn´t receive covering protection. On the concrete production it was used Portland Cement CP II 32, coarse aggregate, fine aggregate and water from the local distributive. Two types of covering were used, one resin based of silicon and solvent and other white cement based, selected sands and acrylic resin. The concrete mixture adopted was 1:1,5:2,5 (cement, fine aggregate, coarse aggregate) and 0.50 water/cement ratio. With the concrete on fresh state was made the experiment test to determinate the workability. On the hardened state was made the concrete resistance experiment, absorption of water and electrochemical experiments, through polarization curves. Also was held optical microscopy and Scanning Electron Microscopy experiments to analyze the layer of the covering applied to the concrete surface and the interface between the concrete and the layer. The obtained results shows that the covering applied to the concrete surface didn´t affect the resistance towards compression. On the absorption of water occurred a diminution of the percentage absorbed, improving the concrete development by making it more impermeable towards the entrance of aggressive agents. The electrochemical experiment results confirmed the water absorption results; the body-of-proof covered presented larger protection towards the development of corrosives process and retarded the evolution of the corrosive phenomenon

Simulador radiográfico antropomórfico de mama humana

Mammography is a diagnostic imaging method in which interpretation depends on knowledge of radiological aspects as well as the clinical exam and pathophysiology of breast diseases. In this work a mammography phantom was developed to be used for training in the operation of mammographic x-ray equipment, image quality evaluation, self-examination and clinical examination of palpation. Polyurethane was used for the production of the phantoms for its physical and chemical properties and because it is one of the components normally used in prostheses. According to the range of flexibility of the polyurethane, it was possible to simulate breasts with higher or lower amount of adipose tissue. Pathologies such as areolar necrosis and tissue rejection due to surgery reconstruction after partial mastectomy were also simulated. Calcifications and nodules were simulated using the following materials: polyethylene, poly (methyl methacrylate), polyamide, polyurethane and poly (dimethyl silicone). Among these, polyethylene was able to simulate characteristics of calcification as well as breast nodules. The results from mammographic techniques used in this paper for the evaluation of the phantoms are in agreement with data found in the literature. The image analyses of four phantoms indicated significant similarities with the human skin texture and the female breast parenchyma. It was possible to detect in the radiographic images produced regions of high and low radiographic optical density, which are characteristic of breasts with regions of different amount of adipose tissue. The stiffnesses of breast phantoms were adjusted according to the formulation of the polyurethane which enabled the production of phantoms with distinct radiographic features and texture similar to human female breast parenchyma. Clinical palpation exam of the phantoms developed in this work indicated characteristics similar to human breast in skin texture, areolar region and parenchyma

Desenvolvimento de sistemas de aditivos químicos para aplicação em cimentações de poços de petróleo

The primary cementing is an important step in the oilwell drilling process, ensuring the mechanical stability of the well and the hydraulic isolation between casing and formation. For slurries to meet the requirements for application in a certain well, some care in the project should be taken into account to obtain a cement paste with the proper composition. In most cases, it is necessary to add chemicals to the cement to modify its properties, according to the operation conditions and thus obtain slurries that can move inside the jacket providing a good displacement to the interest area. New technologies of preparation and use of chemicals and modernization of technological standards in the construction industry have resulted in the development of new chemical additives for optimizing the properties of building materials. Products such as polycarboxylate superplasticizers provide improved fluidity and cohesion of the cement grains, in addition to improving the dispersion with respect to slurries without additives. This study aimed at adapting chemical additives used in civil construction to be used use in oilwell cement slurries systems, using Portland cement CPP-Special Class as the hydraulic binder. The chemical additives classified as defoamer, dispersant, fluid loss controller and retarder were characterized by infrared absorption spectroscopy, thermogravimetric analyses and technological tests set by the API (American Petroleum Institute). These additives showed satisfactory results for its application in cement slurries systems for oil wells. The silicone-based defoamer promoted the reduction of air bubbles incorporated during the stirring of the slurries. The dispersant significantly reduced the rheological parameters of the systems studied. The tests performed with the fluid loss controller and the retarder also resulted in suitable properties for application as chemical additives in cement slurries

Comparação entre duas técnicas de neurorrafia do digital palmar em eqüinos

Foram comparadas duas técnicas de neurorrafia em seis eqüinos, divididos em três grupos (G), conforme o tempo para a biópsia. Os animais foram submetidos a neurectomia dos nervos digitais palmares (NDP) e aplicaram-se duas suturas epineurais (SE) e suturas com tubos de silicone (STS) em cada animal. Avaliaram-se os animais mensalmente pelo teste de sensibilidade e exame do aparelho locomotor até a realização das biópsias dos NDP. Aos 30 dias pós-cirurgia foi realizada biópsia no GI, aos 60 dias no GII e aos 180 dias no GIII. Macroscopicamente, o NDP encontrou-se envolvido por tecido conjuntivo fibroso. Microscopicamente, constataram-se proliferação axonal em uma amostra do GI e neuromas nas amostras dos GI, GII e GIII. Houve proliferação de tecido conjuntivo em todos os grupos no local de reparação para SE e adentrando no interior do tubo na STS. Visibilizaram-se infiltrado de células inflamatórias, alterações no coto proximal e degeneração no coto distal na SE e na STS. As técnicas não apresentaram resultados satisfatórios quanto ao grau de regeneração do coto proximal até o coto distal.

Estudo da papila mamária em fêmeas bovinas (Bos taurus - Linnaeus, 1758), mediante as características ultra-sonográficas em modo-B (tempo real)

Nesta pesquisa foram utilizadas vinte fêmeas bovinas, sem patologias aparentes nas glândulas mamárias, em lactação, objetivando avaliar estruturas anatômicas das papilas mamárias. Quatro técnicas ultra-sonográficas foram avaliadas. Utilizou-se transdutor linear de 7,5 MHz para uso endoretal, na obtenção das imagens, padronizando-se o lado direito do animal para visualização das papilas craniais e caudais, em dois planos anatômicos (sagital e transversal). Os animais foram divididos em quatro grupos (G1, G2, G3, G4) que representaram as diferentes técnicas empregadas em momentos distintos (antes e após ordenha). Os resultados indicaram que entre as técnicas estudadas, as de exame direto e com uso de almofadada de silicone, foram as que apresentaram maior aplicabilidade, quando considerada a sua facilidade de uso na rotina com complementação do exame clinico. Entretanto, pólipos e cálculos lácteos tem sua extensão e localização convenientemente visibilizados mediante uso da técnica de pressão de liquido. Já a técnica de imersão em água, mostrou-se mais eficiente quanto à qualidade das imagens obtidas e na caracterização das estruturas anatômicas. O experimento realizado, traz subsídios anatomo-topográfico que irão contribuir com a qualidade do diagnóstico em pacientes que possam ter indicação cirúrgica (telotomia) e levanta questões que poderão ser respondidas conforme a casuística e a experiência consolidada do cirurgião.

Effect of insulin-like growth factor-1 during in vitro oocyte maturation and in vitro culture of bovine embryos

Avaliaram-se o efeito do IGF-I na maturação in vitro (MIV) (experimento I) e no desenvolvimento embrionário (DE) (experimento II) de oócitos bovinos fecundados in vitro, quanto às taxas de clivagem (TC), de blastocistos (TB) e de eclosão (TE). Para MIV, complexos cumulus-oócitos imaturos foram cultivados em meio TCM-199 suplementado com HEPES, bicarbonato e piruvato de sódio, aditivos, soro fetal bovino (meio B-199) e gonadotrofinas 14U/ml de PMSG e 7U/ml de hCG). Para o desenvolvimento embrionário, os oócitos/zigotos foram cultivados em meio B-199 com células epiteliais do oviduto bovino em suspensão sob óleo de silicone. As condições de cultivo in vitro para ambos os experimentos seguiram os tratamentos: 1- meio B-199 + 200 ng/ml IGF-I; 2- B-199 + 100 ng/ml IGF-I; 3- B-199 + 50 ng/ml IGF-I; 4- B-199 + 10 ng/ml IGF-I; 5- B-199 + 0 ng/ml IGF-I. Todas as culturas foram realizadas a 38,5° C em atmosfera com 5% de CO2 e os dados foram analisados pelo teste do qui-quadrado. No experimento I, não houve diferença (P>0,05) entre os tratamentos quanto às TC, TB e TE, quando o meio de MIV foi suplementado com IGF-I. No experimento II, a adição de IGF-I ao meio de DE resultou em aumento na TC (P<0,05) mas não influenciou a TB e a TE. A adição de 200 ng/ml de IGF-I ao meio DE melhorou a TC (71,1%) quando comparada com a TC dos grupos de 100 ng/ml de IGF-I (57,6%) ou controle (56,7%), entretanto não houve diferença quando comparada com a dos grupos de 50 ng/ml (69,4%) ou 10 ng/ml (73,1%) de IGF-I. Não houve efeito benéfico na adição de 10 a 200 ng/ml de IGF-I nos meios de MIV e de DE com relação ao desenvolvimento de embriões produzidos a partir de oócitos maturados e fecundados in vitro.

Fecundação in vitro de ovócitos bovinos com sêmen submetido a diferentes diluidores

O objetivo deste trabalho foi avaliar a influência do diluidor do sêmen no desenvolvimento in vitro de ovócitos bovinos após a maturação e fecundação in vitro. Ejaculado de um reprodutor foi fracionado e submetido a três diluidores: Lactose/gema de ovo (LG), Citrato/gema de ovo (CG) e Tris/gema de ovo (TG). Amostras deste material foram envasadas, congeladas e estocadas em N² e, posteriormente, descongeladas; a fração móvel foi separada por gradiente descontínuo de Percoll. A concentração espermática foi ajustada para 10 x 10(6)/mL e a capacitação espermática, induzida com 10 µg/mL de heparina. Após 24 horas de cultura para maturação in vitro, os ovócitos, aspirados de folículos ovarianos, foram inseminados com sêmen diluído em meio TALP e, após 48 horas de cultura, os zigotos foram transferidos para gotas de meio TCM 199, com 5% de soro fetal bovino, 5% de soro de vaca em estro e suspensão de células epiteliais do oviduto bovino, cobertas com óleo de silicone, e mantidos em cultura por nove dias. Todas as culturas foram realizadas a 38,5ºC em atmosfera com 5% de CO2. Os dados foram analisados pelo teste do qui-quadrado e houve diferença com relação à taxa de clivagem (TC), sendo as médias de 66,0; 69,3; e 54,4% para LG, CG e TG, respectivamente. Não houve diferença entre tratamentos com relação às taxas de mórulas/blastocistos ou de eclosão. O diluidor do sêmen não teve efeito sobre o desenvolvimento in vitro de embriões bovinos, embora a TC tenha sido afetada.

Produção in vitro de embriões bovinos: utilização de diferentes fontes de gonadotrofinas na maturação dos oócitos

O presente trabalho foi conduzido com o objetivo de avaliar o efeito da utilização de diferentes fontes de gonadotrofinas para maturação in vitro dos oócitos bovinos fecundados e desenvolvidos in vitro sobre as taxas de clivagem (TC) e de blastocistos (TBL). Oócitos imaturos provenientes de ovários de vacas de abatedouro foram submetidos a maturação in vitro sob diferentes condições: meio TCM 199, acrescido de 10% de soro de vaca em estro (SVE), aditivos, hepes, NaHCO3, piruvato de sódio, antibióticos (meio B-199), 20 UI/mL de PMSG e 10 UI/mL de hCG (PMSG/hCG) ou meio B-199, acrescido de 5 mig/mL de FSH e 5 mig/mL de LH (FSH/LH). Seguidos 24 h de cultura a 38,5ºC em atmosfera com 5% de CO2, os oócitos maturos foram incubados com sêmen descongelado durante 18 a 21 horas. Após esse período, os oócitos foram transferidos para placas contendo microgotas de meio Ménezo suplementado com 10% de SVE e células epiteliais do oviduto bovino em suspensão, cobertas com óleo de silicone, os quais permaneceram em cultura por mais 9 dias. Os dados foram analisados pelo teste do Qui-quadrado. A TC e a TBL, para PMSG/hCG e FSH/LH, foram 60 e 13,9% e 61,2 e 10,6%, respectivamente. Não houve diferença entre os tratamentos com relação a TC ou a TBL. Esses resultados sugerem que ambas as fontes de gonadotrofinas podem ser utilizadas para maturação in vitro dos oócitos fecundados e desenvolvidos in vitro.

Obtenção e caracterização de um compósito de poliuretano de mamona e pó de vidro para aplicações em insolantes térmicos

Thermal insulation is used to protect the heated or cooled surfaces by the low thermal conductivity materials. The rigid ricin polyurethane foams (PURM) are used for thermal insulation and depend on the type and concentration of blowing agent. Obtaining PURM occurs by the use of polyol, silicone, catalyst and blowing agent are pre -mixed, reacting with the isocyanate. The glass is reusable, returnable and recyclable heat insulating material, whose time of heat dissipation determines the degree of relaxation of its structure; and viscosity determines the conditions for fusion, operating temperatures, annealing, etc. The production of PURM composites with waste glass powder (PV) represents economical and renewable actions of manufacturing of thermal insulating materials. Based on these aspects, the study aimed to produce and characterize the PURM composites with PV, whose the mass percentages were 5, 10, 20, 30, 40 and 50 wt%. PURM was obtained commercially, while the PV was recycled from the tailings of the stoning process of a glassmaking; when the refining process was applied to obtain micrometer particles. The PURM + PV composites were studied taking into account the standard sample of pure PURM and the influence of the percentage of PV in this PURM matrix. The results of the chemical, physical and morphological characterization were discussed taking into account the difference in the microstructural morphology of the PURM+PV composites and the pure PURM, as well the results of the physicochemical, mechanical e thermophysical tests by values obtained of density, hardness, compressive strength, specific heat, thermal conductivity and diffusivity. In general, the structure of pure PURM showed large, elongated and regular pores, while PURM+PV composites showed irregular, small and rounded pores with shapeless cells. This may have contributed to reducing their mechanical strength, especially for PURM - PV50. The hardness and density were found to have a proportional relationship with the PV content on PURM matrix. The specific heat, thermal diffusivity and thermal conductivity showed proportional relationship to each other. So, this has been realized that the increasing the PV content on PURM matrix resulted in the rise of diffusivity and thermal conductivity and the decrease of the specific heat. However, the values obtained by the PURM composites were similar the values of pure PURM, mainly the PURM-PV5 and PURM-PV10. Therefore, these composites can be applied like thermal insulator; furthermore, their use could reduce the production costs and to preserve the environment

Effects of Formulations Containing Dimethylaminoethanol (DMAE) Acetoamidobenzoate and Pidolate on the Skin

The aim of this study was to analyze the effects of formulations containing DMAE pidolate and DMAE acetoamidobenzoate on the skin. Four areas of five swines were submitted to following treatments during 15 days: C (Control), S (Silicone = 80 % DC*LC Blend (R)), F1 (DMAE acetoamidobenzoate), F2 (DMAE pidolate). Measures of the thickness of epidermis and stratum corneum, and the density population of fibroblasts and leukocytes in papillary dermis were obtained. We also assessed possible variations in birefringence of dermis collagen bundles. Means of the data was compared using ANOVA followed by the Tukey test. The F1 and F2 groups showed a thicker epidermis than the control group (p < 0.01), but did not demonstrate a significant difference in the number of fibroblasts and leukocytes, as well as in the birefringent areas of collagen bundles, in comparison with the control groups. The DMAE-supplemented formulations enhanced viable epidermis thickness, but did not modify structures related with mechanical properties of the skin.

Influence of cassava starch content and sintering temperature on the alumina consolidation technique

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Setting time and thermal expansion of two endodontic cements

The purpose of this study was to evaluate the setting time and the thermal expansion coefficient of 2 endodontic cements, MTA-Angelus and a novel cement called CER. The setting time was determined in accordance to ANSI/ADA specifications no. 57. Three samples of 10 mm diameter and 2 mm thickness were prepared for each cement. The thermal expansion measurements were performed by strain gauge technique. Four samples of each cement were prepared using silicone rings of 5 mm diameter and 2 mm thickness. The data were analyzed statistically using the Student t test. The setting time obtained for the MTA-Angelus and CER cements was 15 (SD 1) min and 7 (SD 1) min, respectively. The linear coefficient of thermal expansion was 8.86 (SD 0.28) mu strain/degrees C for MTA-Angelus and 11.76 (SD 1.20) mu strain/degrees C for CER. The statistical analysis showed significant difference (P < .05) in the setting time and linear coefficient of thermal expansion between the 2 cements. The CER cement has a coefficient of expansion similar to dentin, which could contribute to a decrease of microleakage degree.

Implant-retained thumb prosthesis with anti-rotational attachment for a geriatric patient

This report presents the use of a dental implant with an anti-rotational attachment for the retention of a thumb prosthesis. A retention system was manufactured with an attachment (UCLA) screwed into the implant with a two-bar system that was cast in metallic silver palladium. A substructure made from heat-cured acrylic resin was joined to the retention system by clips to join the thumb to the finger (bar clip) in the cast with implant rejoinder. The silicone material, Silastic-MDX 44210, was used to achieve function and aesthetics. Following osseointegration, no skin problems were observed. Whilst the implant-retained digital prosthesis presented some motor limitations, it allowed the patient to return to entertainment and achieve social conviviality.

Prosthesis Auricular With Osseointegrated Implants and Quality of Life

Implants in craniofacial reconstructions improve prostheses retention and stability, comfort, and safety for the patient. According to biomechanical principles, the treatment success regarding osseointegration maintenance depends on an adequate surgery technique associated to a retention system that provides favorable tension distribution to implants. Implants in the mastoid area are a very important aid for retention of auricular prostheses. Color stability of resin and silicone is an important factor for longevity of auricular prostheses, and the high degree of satisfaction of patients with head and neck defects receiving epithesial reconstruction in the maxillofacial region is demonstrated.

Orbital Implants Insertion to Improve Ocular Prostheses Motility

The objectives of this study were, through a literature review, to point the differences between orbital implants and their advantages and disadvantages, to evaluate prosthesis motility after orbital implants are inserted, and to point the implant wrapping current risks. Sixty-seven articles were reviewed. Enucleation implants can be autoplastics or alloplastics and porous (including natural and synthetic hydroxyapatite [HA]) or nonporous (silicone). Hydroxyapatite is the most related in the literature, but it has disadvantages, too, that is, all orbital implants must be wrapped. Exposure of the porous orbital implant can be repaired using different materials, which include homologous tissue, as well as autogenous graft, xenograft, and synthetic material mesh. The most used materials are HA and porous polyethylene orbital implant. The HA implant is expensive and possibly subject corals to damage, different from porous polyethylene orbital implants. Porous implants show the best prosthesis motility and a minimum rate of implants extrusion. Implant wraps can facilitate smoother entry of the implant into the orbit and allow reattachment of extraocular muscles. They also serve as a barrier between the overlying soft tissue and the rough surface of the implant, protecting implants from exposure or erosion.