PLASMA-INDUCED GRAFTING OF STYRENE ONTO NASCENT POLYETHYLENE POWDER

In this paper, the graft copolymers of styrene to nascent linear polyethylene reactor powders were prepared through plasma graft polymerization. The grafting reaction was initiated by the alkyl radicals formed on the surface of nascent polyethylene with plasma treatment as indicated by electron spin resonance spectra. In graft copolymerization by alkyl radicals, the grafting yield increased with either the plasma power or the plasma treatment lime. Compared with ordinary polyethylene powders, nascent polyethylene reactor powders were found to be more easily plasma-grafted. This has been attributed to the greater sensitivity to irradiation in producing reactive centres under the same conditions. High density polyethylene showed almost the same grafting yield as linear low density polyethylene at 50 degrees C. The surface morphology of nascent polyethylene observed by scanning electron microscope before and after the grafting showed that the silk-like fibrils were not destroyed by plasma treatment.

RELATIONSHIP OF THE SEQUENCE DISTRIBUTION OF A POLYMER TO THE CATALYTIC ACTIVITY OF ITS ND COMPLEX

The sequence distribution of the monomeric units in the styrene-acrylic acid copolymer has been obtained by calculation. The probability of long sequences of styrene increases with an increase in the content of the monomer in the copolymer. The highest distribution of short sequences of styrene takes place for the copolymer containing equimolecular amounts of styrene and acrylic acid. The copolymer which has this latter structure is inadequate for the synthesis of highly active supported complexes. When the distributions of long and short sequences of styrene are approximately equal, the activity of the Nd and Fe prepared polymer complexes is higher.

Characterization of topographical effects on macrophage behavior in a foreign body response model.

Current strategies to limit macrophage adhesion, fusion and fibrous capsule formation in the foreign body response have focused on modulating material surface properties. We hypothesize that topography close to biological scale, in the micron and nanometric range, provides a passive approach without bioactive agents to modulate macrophage behavior. In our study, topography-induced changes in macrophage behavior was examined using parallel gratings (250 nm-2 mum line width) imprinted on poly(epsilon-caprolactone) (PCL), poly(lactic acid) (PLA) and poly(dimethyl siloxane) (PDMS). RAW 264.7 cell adhesion and elongation occurred maximally on 500 nm gratings compared to planar controls over 48 h. TNF-alpha and VEGF secretion levels by RAW 264.7 cells showed greatest sensitivity to topographical effects, with reduced levels observed on larger grating sizes at 48 h. In vivo studies at 21 days showed reduced macrophage adhesion density and degree of high cell fusion on 2 mum gratings compared to planar controls. It was concluded that topography affects macrophage behavior in the foreign body response on all polymer surfaces examined. Topography-induced changes, independent of surface chemistry, did not reveal distinctive patterns but do affect cell morphology and cytokine secretion in vitro, and cell adhesion in vivo particularly on larger size topography compared to planar controls.

Caracterização e transformação de Lenhosulfonatos de Eucalyptus globulus

Os lenhosulfonatos representam um sub-produto formado durante o cozimento ao sulfito ácido, sendo queimados para a regeneração da base e recuperação de energia. No entanto, os lenhosulfonatos são também considerados uma importante matéria-prima para a produção de vários produtos de valor acrescentado. Os objectivos principais deste trabalho foram contribuir para uma melhor compreensão sobre a caracterização química e estrutural dos lenhosulfonatos do Eucalyptus globulus, assim como, para complementar a informação disponível sobre a síntese e a caracterização estrutural e térmica de materiais poliméricos obtidos a partir de compostos modelo dos produtos de oxidação dos lenhosulfonatos. O licor de cozimento ao sulfito foi analisado em termos do teor de cinzas, extractáveis, compostos voláteis, açúcares e lenhosulfonatos. O teor de cinzas e açúcares no licor de cozimento é muito elevado, tendo sido necessário purificar o mesmo (2,8-13,8 % e 3,2-9,1 %, respectivamente). A análise dos açúcares mostrou uma quantidade considerável de pentoses, sendo o açúcar predominante a xilose. Os lenhosulfonatos foram purificados, isolados e caracterizados por química molhada (titulação potenciométrica e oxidação com permanganato), análise elementar, espectroscopia de ultravioleta/visível (UV/Vis), espectroscopia de infravermelho de transformada de Fourier (FTIR), espectroscopia de ressonância magnética nuclear de protão (RMN de 1H) e carbono (RMN de 13C), espectrometria de massa de ionização por electrospray (ESI-MS), cromatografia de permeação em gel (GPC), termogavimetria (TGA) e calorimetria diferencial de varrimento (DSC). Os lenhosulfonatos são constituídos principalmente por unidades S, são parcialmente sulfonados e possuem um peso molecular relativamente baixo (Mw = 1250-2400 Da). A ruptura das ligações β-O-4 e α-O-4 da lenhina do Eucalyptus globulus após cozimento ao sulfito ácido originam olígomeros de baixo peso molecular cuja estrutura foi elucidada por RMN 1D/2D e ESI-MS. A degradação térmica dos lenhosulfonatos apresentou dois máximos de degradação a 188-190ºC e a 315-380ºC. As curvas de DSC mostraram um pico endotérmico para temperaturas inferiores a 130ºC e um pico exotérmico a 300-500ºC. Os lenhosulfonatos foram despolimerizados na presença de oxigénio molecular em meio alcalino. Os produtos de oxidação principais foram o aldeído siríngico, a vanilina, o ácido vanílico e o ácido siríngico. A adição do catalisador (sal de cobre) promoveu a oxidação dos lenhosulfonatos aumentando o rendimento dos aldeídos aromáticos (< 50%). A presença de açúcares nos lenhosulfonatos teve um efeito negativo no rendimento dos produtos de oxidação principais. Alguns compostos modelo dos produtos de oxidação dos lenhosulfonatos foram polimerizados por poliadição (catiónica e radicalar) e policondensação. Os monómeros e os polímeros foram caracterizados por espectroscopia de infravermelho de transformada de Fourier e reflectância total atenuada (FTIR-ATR), RMN em solução e no estado sólido, UV/Vis no estado sólido, GPC, difracção de raios-X (XRD), TGA e DSC. Os compostos modelo estudados foram os estirenos metoxi-substituídos (p-metoxiestireno e 3,4-dimetoxiestireno) e os ácidos hidroxi aromáticos metoxi-substituídos (ácido vanílico e ácido siríngico). O 3,4-dimetoxiestireno foi ainda copolimerizado com o éter isobutil vinílico e os seus copolímeros foram desmetilados, assim como, o poli(p-metoxiestireno) e o poli(3,4-dimetoxiestireno). A polimerização catiónica do p-metoxiestireno e 3,4-dimetoxiestireno é mais rápida e mais completa do que a polimerização radicalar produzindo polímeros com pesos moleculares elevados. O poli(p-metoxiestireno) (Mw = 235000 Da) possui um peso molecular maior do que o poli(3,4-dimetoxiestireno) (Mw = 18800 Da). A estabilidade térmica e a temperatura de transição vítrea diminuiram com a presença do segundo grupo metoxilo. A desmetilação dos homopolímeros foi bem sucedida, tendo sido corroborada por FTIR-ATR e RMN. A policondensação do ácido siríngico foi dificultada pela presença do segundo grupo metoxilo, tendo sido necessário adicionar uma maior quantidade do agente de condensação devido a factores estéricos. O poli(ácido vanílico) e poli(ácido siríngico) são insolúveis na maior parte dos solventes orgânicos, sendo parcialmente solúveis em clorofórmio, ácido triflúoracético, 1,1,2,2- tetracloroetano, dimetilsulfóxido, tetrahidrofurano, N,N’-dimetilformamida e 1,1,1,3,3,3-hexaflúor-2-propanol. A estabilidade térmica diminuiu com a presença do segundo grupo metoxilo e os dois polímeros não exibiram temperatura de transição vítrea. O poli(ácido vanílico) e poli(ácido siríngico) apresentaram uma estrutura muito cristalina (grau de cristalinidade 70% e 50%, respectivamente). O segundo grupo metoxilo aumentou o valor da absorvância, mas a forma do espectro de UV/Vis foi similar. A polimerização catiónica do éter isobutil vinílico resultou na produção de um polímero muito viscoso com peso molecular elevado (Mw = 20400 Da). A degradação térmica do polímero ocorreu em várias gamas de temperatura e foi completa (0% de resíduo a 800ºC). A copolimerização catiónica do 3,4-dimetoxiestireno com o éter isobutil vinílico foi realizada com proporções diferentes 80:20, 50:50 e 20:80. Os copolímeros apresentaram uma viscosidade elevada e um peso molecular baixo (Mw = 2000-4000 Da) que aumentou com a quantidade de éter isobutil vinílico. A degradação térmica dos copolímeros ocorreu também em várias gamas de temperatura, sendo a sua degradação completa (0,9-1,5% de resíduo a 800ºC). A desmetilação dos copolímeros não foi bem sucedida, tendo sido confirmada por FTIR-ATR e RMN.

Engineering bio-based polymers using alternative solvents and processes

The work presented in this thesis explores novel routes for the processing of bio-based polymers, developing a sustainable approach based on the use of alternative solvents such as supercritical carbon dioxide (scCO2), ionic liquids (ILs) and deep eutectic solvents (DES). The feasibility to produce polymeric foams via supercritical fluid (SCF) foaming, combined with these solvents was assessed, in order to replace conventional foaming techniques that use toxic and harmful solvents. A polymer processing methodology is presented, based on SCF foaming and using scCO2 as a foaming agent. The SCF foaming of different starch based polymeric blends was performed, namely starch/poly(lactic acid) (SPLA) and starch/poly(ε-caprolactone) (SPCL). The foaming process is based on the fact that CO2 molecules can dissolve in the polymer, changing their mechanical properties and after suitable depressurization, are able to create a foamed (porous) material. In these polymer blends, CO2 presents limited solubility and in order to enhance the foaming effect, two different imidazolium based ILs (IBILs) were combined with this process, by doping the blends with IL. The use of ILs proved useful and improved the foaming effect in these starch-based polymer blends. Infrared spectroscopy (FTIR-ATR) proved the existence of interactions between the polymer blend SPLA and ILs, which in turn diminish the forces that hold the polymeric structure. This is directly related with the ability of ILs to dissolve more CO2. This is also clear from the sorption experiments results, where the obtained apparent sorption coefficients in presence of IL are higher compared to the ones of the blend SPLA without IL. The doping of SPCL with ILs was also performed. The foaming of the blend was achieved and resulted in porous materials with conductivity values close to the ones of pure ILs. This can open doors to applications as self-supported conductive materials. A different type of solvents were also used in the previously presented processing method. If different applications of the bio-based polymers are envisaged, replacing ILs must be considered, especially due to the poor sustainability of some ILs and the fact that there is not a well-established toxicity profile. In this work natural DES – NADES – were the solvents of choice. They present some advantages relatively to ILs since they are easy to produce, cheaper, biodegradable and often biocompatible, mainly due to the fact that they are composed of primary metabolites such as sugars, carboxylic acids and amino-acids. NADES were prepared and their physicochemical properties were assessed, namely the thermal behavior, conductivity, density, viscosity and polarity. With this study, it became clear that these properties can vary with the composition of NADES, as well as with their initial water content. The use of NADES in the SCF foaming of SPCL, acting as foaming agent, was also performed and proved successful. The SPCL structure obtained after SCF foaming presented enhanced characteristics (such as porosity) when compared with the ones obtained using ILs as foaming enhancers. DES constituted by therapeutic compounds (THEDES) were also prepared. The combination of choline chloride-mandelic acid, and menthol-ibuprofen, resulted in THEDES with thermal behavior very distinct from the one of their components. The foaming of SPCL with THEDES was successful, and the impregnation of THEDES in SPCL matrices via SCF foaming was successful, and a controlled release system was obtained in the case of menthol-ibuprofen THEDES.

New grafted PLA-g-PEG polymeric nanoparticles used to improve bioavailability of oral drugs.

Les nanoparticules (NPs) de polymère ont montré des résultats prometteurs pour leur utilisation comme système de transport de médicaments pour une libération contrôlée du médicament, ainsi que pour du ciblage. La biodisponibilité des médicaments administrés oralement pourrait être limitée par un processus de sécrétion intestinale, qui pourrait par la suite être concilié par la glycoprotéine P (P-gp). La dispersion de la Famotidine (modèle de médicament) à l’intérieur des nanoparticules (NPs) pegylées a été évaluée afin d’augmenter la biodisponibilité avec du polyéthylène glycol (PEG), qui est connu comme un inhibiteur de P-gp. L’hypothèse de cette étude est que l’encapsulation de la Famotidine (un substrat de P-gp) à l’intérieur des NPs préparées à partir de PEG-g-PLA pourrait inhiber la fonction P-gp. La première partie de cette étude avait pour but de synthétiser quatre copolymères de PEG greffés sur un acide polylactide (PLA) et sur un squelette de polymère (PLA-g-PEG), avec des ratios de 1% et 5% (ratio molaire de PEG vs acide lactique monomère) de soit 750, soit 2000 Da de masse moléculaire. Ces polymères ont été employés afin de préparer des NPs chargés de Famotidine qui possède une faible perméabilité et une solubilité aqueuse relativement basse. Les NPs préparées ont été analysées pour leur principaux paramètres physicochimiques tels que la taille et la distribution de la taille, la charge de surface (Potentiel Zeta), la morphologie, l’efficacité d’encapsulation, le pourcentage résiduel en alcool polyvinylique (PVA) adsorbé à la surface des NPs, les propriétés thermiques, la structure cristalline et la libération du médicament. De même, les formules de NPs ont été testées in vitro sur des cellules CaCo-2 afin dʼévaluer la perméabilité bidirectionnelle de la Famotidine. Généralement, les NPs préparées à partir de polymères greffés PLA-g-5%PEG ont montré une augmentation de la perméabilité du médicament, ce par l’inhibition de l’efflux de P-gp de la Famotidine dans le modèle CaCo-2 in vitro. Les résultats ont montré une baisse significative de la sécrétion de la Famotidine de la membrane basolatéral à apical lorsque la Famotidine était encapsulée dans des NPs préparées à partir de greffes de 5% PEG de 750 ou 2000 Da, de même que pour d’autres combinaisons de mélanges physiques contenant du PEG5%. La deuxième partie de cette étude est à propos de ces NPs chargées qui démontrent des résultats prometteurs en termes de perméabilité et d’inhibition d’efflux de P-gp, et qui ont été choises pour développer une forme orale solide. La granulation sèche a été employée pour densifier les NPs, afin de développer des comprimés des deux formules sélectionnées de NPs. Les comprimés à base de NPs ont démontré un temps de désintégration rapide (moins d’une minute) et une libération similaire à la Famotidine trouvée sur le marché. Les résultats de l’étude du transport de comprimés à base de NPs étaient cohérents avec les résultats des formules de NPs en termes d’inhibition de P-gp, ce qui explique pourquoi le processus de fabrication du comprimé n’a pas eu d’effet sur les NPs. Mis ensemble, ces résultats montrent que l’encapsulation dans une NP de polymère pegylé pourrait être une stratégie prometteuse pour l’amélioration de la biodisponibilité des substrats de P-gp.

Effect of Polymer Architecture on the Structural and Biophysical Properties of PEG-PLA Nanoparticles

Polymers made of poly(ethylene glycol) chains grafted to poly(lactic acid) chains (PEG-g-PLA) were used to produce stealth drug nanocarriers. A library of comb-like PEG-g-PLA polymers with different PEG grafting densities was prepared in order to obtain nanocarriers with dense PEG brushes at their surface, stability in suspension, and resistance to protein adsorption. The structural properties of nanoparticles (NPs) produced from these polymers by a surfactant-free method were assessed by DLS, zeta potential, and TEM and were found to be controlled by the amount of PEG present in the polymers. A critical transition from a solid NP structure to a soft particle with either a “micelle-like” or “polymer nano-aggregate” structure was observed when the PEG content was between 15 to 25% w/w. This structural transition was found to have a profound impact on the size of the NPs, their surface charge, their stability in suspension in presence of salts as well as on the binding of proteins to the surface of the NPs. The arrangement of the PEG-g-PLA chains at the surface of the NPs was investigated by 1H NMR and X-ray photoelectron spectroscopy (XPS). NMR results confirmed that the PEG chains were mostly segregated at the NP surface. Moreover, XPS and quantitative NMR allowed quantifying the PEG chain coverage density at the surface of the solid NPs. Concordance of the results between the two methods was found to be remarkable. Physical-chemical properties of the NPs such as resistance to aggregation in saline environment as well as anti-fouling efficacy were related to the PEG surface density and ultimately to polymer architecture. Resistance to protein adsorption was assessed by isothermal titration calorimetry (ITC) using lysozyme. The results indicate a correlation between PEG surface coverage and level of protein interactions. The results obtained lead us to propose such PEG-g-PLA polymers for nanomedecine development as an alternative to the predominant polyester-PEG diblock polymers.

Effect of polymer architecture on Curcumin 1 encapsulation and release from PEGylated polymer nanoparticles: toward a drug delivery nano-platform to the CNS

We developed a nanoparticles (NPs) library from poly(ethylene glycol)–poly lactic acid comb-like polymers with variable amount of PEG. Curcumin was encapsulated in the NPs with a view to develop a delivery platform to treat diseases involving oxidative stress affecting the CNS. We observed a sharp decrease in size between 15 and 20% w/w of PEG which corresponds to a transition from a large solid particle structure to a “micelle-like” or “polymer nano-aggregate” structure. Drug loading, loading efficacy and release kinetics were determined. The diffusion coefficients of curcumin in NPs were determined using a mathematical modeling. The higher diffusion was observed for solid particles compared to “polymer nano-aggregate” particles. NPs did not present any significant toxicity when tested in vitro on a neuronal cell line. Moreover, the ability of NPs carrying curcumin to prevent oxidative stress was evidenced and linked to polymer architecture and NPs organization. Our study showed the intimate relationship between the polymer architecture and the biophysical properties of the resulting NPs and sheds light on new approaches to design efficient NP-based drug carriers.

Développement de nouveaux polymères amphiphiles comme floculants versatiles pour le traitement de l’eau issue de l’industrie pétrolière

Les polymères hydrosolubles sont utilisés dans diverses industries pour permettre la floculation, soit une séparation solide-liquide de particules présentes en suspension colloïdale. Afin de réduire les impacts environnementaux de l’exploitation des sables bitumineux en Alberta, l’industrie est à la recherche de nouveaux moyens et procédés pour traiter les résidus miniers permettant de séparer les matières solides et de récupérer l’eau. L’objectif des travaux présentés est d’améliorer la floculation, la densification et la déshydratation de ces résidus miniers aqueux par de nouveaux polymères synthétiques. Des homopolymères d’acrylamide de différentes masses molaires ont été synthétisés pour étudier l’influence de la masse molaire sur l’efficacité de floculation. Le taux initial de sédimentation (TIS) est le paramètre qui fut utilisé afin de comparer l’efficacité de floculation des différents polymères. Il a été possible de confirmer l’importance de la masse molaire sur l’efficacité de floculation et de déterminer une masse molaire minimale d’environ 6 MDa pour des polyacrylamides, afin d’obtenir l’efficacité de floculation maximale de suspensions colloïdales principalement composées de kaolin. Afin d’étudier l’effet des charges sur l’efficacité de floculation, des polymères anioniques et cationiques ont été synthétisés. Une série de copolymères d’acrylamide et d’acide acrylique ont été synthétisés comme polymères anioniques et deux séries de copolymères ont été synthétisés comme polymères cationiques, soit des copolymères d’acrylamide et de chlorure de diallyldiméthylammonium et des copolymères de 4-vinyl pyridine et de 1-méthyl-4-vinyl pyridinium. Il a été démontré que les charges anioniques des polymères avaient peu d’influence sur l’efficacité de floculation et que leur comportement en présence de sels était différent de ce que prévoyait la littérature. Il a aussi été démontré que les charges cationiques des polymères n’améliorent pas l’efficacité de floculation. Par la suite, des séries de copolymères amphiphiles, avec des monomères d’acrylamide, de N-alkylacrylamides et d’acrylonitrile, ont été synthétisés, pour étudier l’effet du caractère amphiphile sur la déshydratation des résidus miniers. Le pourcentage de déshydratation nette est le paramètre qui fut utilisé afin de comparer l’efficacité de déshydratation des différents polymères. Il a été possible de développer des copolymères amphiphiles qui améliorent l’efficacité de déshydratation par rapport à des homopolymères d’acrylamide. Il ne fut pas possible de déterminer une tendance entre la balance hydrophile/hydrophobe des copolymères amphiphiles et l’efficacité de déshydratation.

Self-Assembly of Stimuli-Responsive Water-Soluble [60]Fullerene End-Capped Ampholytic Block Copolymer

Well-defined, water-soluble, pH and temperature stimuli-responsive [60]fullerene (C₆₀) containing ampholytic block copolymer of poly((methacrylic acid)-block-(2-(dimethylamino)ethyl methacrylate))-block–C₆₀ (P(MAA-b-DMAEMA)-b-C₆₀) was synthesized by the atom transfer radical polymerization (ATRP) technique. The self-assembly behaviour of the C₆₀ containing polyampholyte in aqueous solution was characterized by dynamic light scattering (DLS), and transmission electron microscopy. This amphiphilic mono-C₆₀ end-capped block copolymer shows enhanced solubility in aqueous medium at room and elevated temperatures and at low and high pH but phase-separates at intermediate pH of between 5.4 and 8.8. The self assembly of the copolymer is different from that of P(MAA-b-DMAEMA). Examination of the association behavior using DLS revealed the co-existence of unimers and aggregates at low pH at all temperatures studied, with the association being driven by the balance of hydrophobic and electrostatic interactions. Unimers and aggregates of different microstructures are also observed at high pH and at temperatures below the lower critical solution temperature (LCST) of PDMAEMA. At high pH and at temperatures above the LCST of PDMAEMA, the formation of micelles and aggregates co-existing in solution is driven by the combination of hydrophobic, electrostatic, and charge-transfer interactions.

Stimuli-responsive Novel Amphiphilic Polymers for Chemical and Biomedical Applications

Amphiphilic polymers are a class of polymers that self-assemble into different types of microstructure, depending on the solvent environment and external stimuli. Self assembly structures can exist in many different forms, such as spherical micelles, rod-like micelles, bi-layers, vesicles, bi-continuous structure etc. Most biological systems are basically comprised of many of these organised structures arranged in an intelligent manner, which impart functions and life to the system. We have adopted the atom transfer radical polymerization (ATRP) technique to synthesize various types of block copolymer systems that self-assemble into different microstructure when subject to an external stimuli, such as pH or temperature. The systems that we have studied are: (1) pH responsive fullerene (C60) containing poly(methacrylic acid) (PMAA-b-C60); (2) pH and temperature responsive fullerene containing poly[2-(dimethylamino)ethyl methacrylate] (C₆₀-b-PDMAEMA); (3) other responsive water-soluble fullerene systems. By varying temperature, pH and salt concentration, different types microstructure can be produced. In the presence of inorganic salts, fractal patterns at nano- to microscopic dimension were observed for negatively charged PMAA-b-C60, while such structure was not observed for positively charged PDMAEMA-b-C60. We demonstrated that negatively charged fullerene containing polymeric systems can serve as excellent nano-templates for the controlled growth of inorganic crystals at the nano- to micrometer length scale and the possible mechanism was proposed. The physical properties and the characteristics of their self-assembly properties will be discussed, and their implications to chemical and biomedical applications will be highlighted.

Enhancing the catalytic repertoire of nucleic acids: a systematic study of linker length and rigidity

The incorporation of potentially catalytic groups in DNA is of interest for the in vitro selection of novel deoxyribozymes, A series of 10 C5-modified analogues of 2'-deoxyuridine triphosphate have been synthesised that possess side chains of differing flexibility and bearing a primary amino or imidazole functionality, For each series of nucleotide analogues differing degrees of flexibility of the C5 side chain was achieved through the use of alkynyl, alkenyl and alkyl moieties, The imidazole function was conjugated to these CS-amino-modified nucleotides using either imidazole 4-acetic acid or imidazole 4-acrylic acid (urocanic acid), The substrate properties of the nucleotides (fully replacing dTTP) with Taq polymerase during PCR have been investigated in order to evaluate their potential applications for in vitro selection experiments, 5-(3-Aminopropynyl)dUTP and 5-(E-3-aminopropenyl)dUTP and their imidazole 4-acetic acid- and urocanic acid-modified conjugates were found to be substrates, In contrast, C5-amino-modified dUTPs with alkane or Z-alkene linkers and their corresponding conjugates were not substrates, The incorporation of these analogues during PCR has been confirmed by inhibition of restriction enzyme digestion using XbaI and by mass spectrometry of the PCR products.

Development of Highly Selective Enzymatic Devices Based on Deposition of Permselective Membranes on Aligned Nanowires

We describe a simple and efficient strategy to fabricate enzymatic devices based on the deposition of glucose oxidase on aligned and highly oriented CoNiMo metallic nanowires. CoNiMo nanowires with an average diameter of 200 nm and length of 50 mu m were electrodeposited on Au-covered alumina substrates via electrodeposition, using alumina membranes as templates. Enzyme-modified electrodes were fabricated via enzyme immobilization using a cross-linker. To minimize nonspecific reactions in the presence of interfering agents, a permselective membrane composed of poly(vinylsulfonic acid) and polyamidoamine dendrimer was deposited via electrostatic interaction. The formation of hydrogen peroxide as a product of the enzymatic reaction was monitored at low overpotential, 0.0 V (vs Ag/AgCl). The detection limit was estimated at 22 mu M under an applied potential of 0.0 V. The apparent Michaelis-Menten constant determined from the Lineweaver-Burke plot was 2 mM.

Síntese e caracterização do poli(ácido láctico) para potencial uso em sistemas de liberação controlada de fármacos

With the advances in medicine, life expectancy of the world population has grown considerably in recent decades. Studies have been performed in order to maintain the quality of life through the development of new drugs and new surgical procedures. Biomaterials is an example of the researches to improve quality of life, and its use goes from the reconstruction of tissues and organs affected by diseases or other types of failure, to use in drug delivery system able to prolong the drug in the body and increase its bioavailability. Biopolymers are a class of biomaterials widely targeted by researchers since they have ideal properties for biomedical applications, such as high biocompatibility and biodegradability. Poly (lactic acid) (PLA) is a biopolymer used as a biomaterial and its monomer, lactic acid, is eliminated by the Krebs Cycle (citric acid cycle). It is possible to synthesize PLA through various synthesis routes, however, the direct polycondensation is cheaper due the use of few steps of polymerization. In this work we used experimental design (DOE) to produce PLAs with different molecular weight from the direct polycondensation of lactic acid, with characteristics suitable for use in drug delivery system (DDS). Through the experimental design it was noted that the time of esterification, in the direct polycondensation, is the most important stage to obtain a higher molecular weight. The Fourier Transform Infrared (FTIR) spectrograms obtained were equivalent to the PLAs available in the literature. Results of Differential Scanning Calorimetry (DSC) showed that all PLAs produced are semicrystalline with glass transition temperatures (Tgs) ranging between 36 - 48 °C, and melting temperatures (Tm) ranging from 117 to 130 °C. The PLAs molecular weight characterized from Size Exclusion Chromatography (SEC), varied from 1000 to 11,000 g/mol. PLAs obtained showed a fibrous morphology characterized by Scanning Electron Microscopy (SEM)

Síntese do Poli (ácido láctico) por policondensação direta utilizando um planejamento fatorial

The environmental impact caused by the disposal of non-biodegradable polymer packaging on the environment, as well as the high price and scarcity of oil, caused increase of searches in the area of biodegradable polymers from renewable resources were developed. The poly (lactic acid) (PLA) is a promising polymer in the market, with a large availability of raw material for the production of its monomer, as well as good processability. The aimed of this study was synthesis PLA by direct polycondesation of lactic acid, using the tool of experimental design (DOE) (central composite rotatable design (CCRD)) to optimize the conditions of synthesis. The polymer obtained was characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), viscosimetric analysis, differential scanning calorimeter (DSC) and size exclusion chromatography (SEC). The results confirmed the formation of a poly (lactic acid) semicrystalline in the syntheses performed. Through the central composite rotatable design was possible to optimize the crystallization temperature (Tc) and crystallinity degree (Xc). The crystallization temperature maximum was found for percentage of catalyst around the central point (0,3 (%W)) and values of time ranging from the central point (6h) to the upper level (+1) (8h). The crystallization temperature maximum was found for the total synthesis time of 4h (-1) and percentage of catalyst 0,1(W%) (-1). The results of size exclusion chromatography (SEC) showed higher molecular weights to 0,3 (W%) percent of catalyst and total time synthesis of 3,2h