Optimising the design and manufacture of a customised, prescription fit, Maxillo-facial prosthesis

This thesis is a continuation of the Enterprise-Ireland Research Innovation Fund (RIF) Project entitled’ "Design and Manufacturing of Customised Maxillo-Facial Prostheses" The primary objective of this Internal Research Development Program (IRDP) project was to investigate two fundamental design changes 1 To incorporate the over-denture abutments directly into the implant. 2 To remove the restraining wings by the addition of screws, which affix the. implant to the dense material of the jawbone. The prosthetic was redesigned using the ANSYS Finite Element Analysis software program and analysed to* • Reduce the internal von Mises stress distribution The new prosthetic had a -63.63 % lower von Mises stress distribution when compared with the original prosthetic. • Examine the screw preload effects. A maximum relative displacement of 22 6 * lO^mm between the bone and screw was determined, which is well below the critical threshold of micromotion which prevents osseointegration • Investigate the prosthetic-bone contact interface. Three models of the screw, prosthesis, and bone, were studied. (Axisymmetnc, quarter volume, and full volume), a recommended preload torque of 0 32 Nm was applied to the prosthetic and a maximum von Mises stress of 1.988 MPa was predicted • Study the overdenture removal forces. This analysis could not be completed because the correct plastic multilinear properties of the denture material could not be established The redesigned prosthetic was successfully manufactured on a 3-axis milling machine with an indexing system The prosthetic was examined for dimensional quality and strength The research established the feasibility of the new design and associated manufacturing method.

Experimental and model-based analysis of the steady-state and dynamic operating behaviour of the direct methanol fuel cell (DMFC)

Direct methanol fuel cell, DMFC, model, mass transport, Maxwell-Stefan, Flory-Huggins, crossover, polymer electrolyte membrane, Nafion

System-oriented analysis of the dynamic behaviour of direct methanol fuel cells

DMFC, dynamic behaviour, current steps, system analysis, methanol oxidation, flow field design

Influence of pore size distribution on drying behaviour of porous media by a continuous model

Bundle of capillaries, drying kinetics, continuous model, relative permeability, capillary pressure, control volume method

Modelling the influence of microstructure on elastic properties and tensile damage behaviour of Mo-base silicide alloys

Mo-Si-B alloys, Real microstructures, Voronoi structures, Microstructural characterization, Modelling and finite element simulations, Effective material properties, Damage and Crack growth, tensile strength, fracture toughness

Simulation of the deformation behaviour of two-phase composites

Two-phase polycrystal, elasto-viscoplastic material model, heterogeneity, anisotropy, flow behaviour, crystallographic texture, strain field

Numerical investigation of micro and macro mechanical behaviour of granular media via a discrete element approach

Magdeburg, Univ., Fak. für Mathematik, Diss., 2009

Alternatives to Aerobic Exercise Prescription in Patients with Chronic Heart Failure

Background: Exercise is essential for patients with heart failure as it leads to a reduction in morbidity and mortality as well as improved functional capacity and oxygen uptake (v̇O2). However, the need for an experienced physiologist and the cost of the exam may render the cardiopulmonary exercise test (CPET) unfeasible. Thus, the six-minute walk test (6MWT) and step test (ST) may be alternatives for exercise prescription. Objective: The aim was to correlate heart rate (HR) during the 6MWT and ST with HR at the anaerobic threshold (HRAT) and peak HR (HRP) obtained on the CPET. Methods: Eighty-three patients (58 ± 11 years) with heart failure (NYHA class II) were included and all subjects had optimized medication for at least 3 months. Evaluations involved CPET (v̇O2, HRAT, HRP), 6MWT (HR6MWT) and ST (HRST). Results: The participants exhibited severe ventricular dysfunction (ejection fraction: 31 ± 7%) and low peak v̇O2 (15.2 ± 3.1 mL.kg-1.min-1). HRP (113 ± 19 bpm) was higher than HRAT (92 ± 14 bpm; p < 0.05) and HR6MWT (94 ± 13 bpm; p < 0.05). No significant difference was found between HRP and HRST. Moreover, a strong correlation was found between HRAT and HR6MWT (r = 0.81; p < 0.0001), and between HRP and HRST (r = 0.89; p < 0.0001). Conclusion: These findings suggest that, in the absence of CPET, exercise prescription can be performed by use of 6MWT and ST, based on HR6MWT and HRST

Impact of casting parameters and chemical composition on the solidification behaviour of Al-Si-Cu hypoeutectic alloy

Magdeburg, Univ., Fak. für Maschinenbau, Diss., 2010

Existence, multiplicity and behaviour of solutions of some elliptic differential equations of higher order

Magdeburg, Univ., Fak. für Mathematik, Diss., 2009

Targeted search engines for children : search user interfaces and information-seeking behaviour

Magdeburg, Univ., Fak. für Informatik, Diss., 2015

Oviposition behaviour of Gryon gallardoi (Hymenoptera, Scelionidae) on eggs of different ages of Spartocera dentiventris (Hemiptera, Coreidae)

The oviposition behaviour of Gryon gallardoi (Brèthes, 1914) on eggs of Spartocera dentiventris Mendonça Jr. (Berg, 1884) of different ages (2, 3, 4, 5, 6, 7, 8 and 12 days) was investigated. Groups of 12 eggs of each age were exposed to single females of G. gallardoi, and the oviposition behaviour was recorded under a stereomicroscope for two hours. Ten replicates were used for each age. In order to identify the moment the parasitoid egg was released inside the host, 1-day old eggs of S. dentiventris were exposed to G. gallardoi females, and the oviposition was interrupted at intervals of 20, 40, 60, 80, 100, 120, 140 and 160s after ovipositor insertion had initiated. Five behavioural steps were recorded: drumming, ovipositor insertion, marking, walking and resting. The average drumming and ovipositor insertion times increased with the host age (P<0.01). Ovipositor insertion usually occurred next to the longitudinal extremities of the host eggs. Marking took on average 19.5 ± 0.7s, and as walking and resting, was not affected by host age. Self-parasitism behaviour was observed in only 13.8 ± 2.3% of the eggs, being more evident with increasing patch depletion (reduction in non-parasitized eggs in the egg group, P<0.01), again with no variation due to changes in host egg age. For all ages tested, self-parasitized host eggs were less frequently contacted and accepted than non-parasitized ones (P<0.01). The parasitoid egg was released 137.0 ± 3.7s after ovipositor insertion. Spartocera dentiventris egg condition can lead to parasitoid behavioural changes, especially during the process of host choice and discrimination.