Shear bond strength of repairs in porcelain conditioned with laser

The aim of this study was to evaluate the shear bond strength of repairs in porcelain conditioned with laser. Sixty porcelain discs were made and six groups were formed (n = 10): G1: conditioning with laser with potency 760 mW; G2: conditioning with laser with potency 760 mW and application of 37% phosphoric acid for 15 s; G3: conditioning with laser with potency 900 mW; G4: conditioning with laser with potency 900 mW and application of 37% phosphoric acid for 15 s; G5: application of 37% phosphoric acid for 15 s (group control) and G6: application of 10% hydrofluoric acid for 2 min. The composite resin was insert of incremental layers at the porcelain surface aided with a metal matrix, and photoactivation for 20 s each increment. The specimens were submitted to a thermal cycling by 1000 cycles of 30 s in each bath with temperature between 5 and 55 degrees C. After the thermal cycling, specimens were submitted to the shear bond strength. The results were evaluated statistically through analysis of variance and Tukey's tests with 5% significance. The averages and standard deviation founded were: G1, 11.25 (+/- 3.10); G2, 12.32 (+/- 2.65); G3, 14.02 (+/- 2.38); G4, 13.44 (+/- 2,07); G5, 9.91 (-/+ 2,18); G6, 12.74 (+/- 2.67). The results showed that the femtosecond laser produced a shear bond strength of repairs in porcelain equal to the hydrofluoric acid and significantly superior to the use of phosphoric acid. Microsc. Res. Tech., 2012. (C) 2012 Wiley Periodicals, Inc.

Effect of dental tissue conditioners and matrix metalloproteinase inhibitors on type I collagen microstructure analyzed by Fourier transform infrared spectroscopy

This study aimed to evaluate the chemical interaction of collagen with some substances usually applied in dental treatments to increase the durability of adhesive restorations to dentin. Initially, the similarity between human dentin collagen and type I collagen obtained from commercial bovine membranes of Achilles deep tendon was compared by the Attenuated Total Reflectance technique of Fourier Transform Infrared (ATR-FTIR) spectroscopy. Finally, the effects of application of 35% phosphoric acid, 0.1M ethylenediaminetetraacetic acid (EDTA), 2% chlorhexidine, and 6.5% proanthocyanidin solution on microstructure of collagen and in the integrity of its triple helix were also evaluated by ATR-FTIR. It was observed that the commercial type I collagen can be used as an efficient substitute for demineralized human dentin in studies that use spectroscopy analysis. The 35% phosphoric acid significantly altered the organic content of amides, proline and hydroxyproline of type I collagen. The surface treatment with 0.1M EDTA, 2% chlorhexidine, or 6.5% proanthocyanidin did not promote deleterious structural changes to the collagen triple helix. The application of 6.5% proanthocyanidin on collagen promoted hydrogen bond formation. (c) 2012 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2012.

Minimal alterations on the enamel surface by micro-abrasion: in vitro roughness and wear assessments

Objective: To evaluate the in vitro changes on the enamel surface after a micro-abrasion treatment promoted by different products. Material and Methods: Fifty (50) fragments of bovine enamel (15 mm × 5 mm) were randomly assigned to five groups (n=10) according to the product utilized: G1 (control)= silicone polisher (TDV), G2= 37% phosphoric acid (3M/ESPE) + pumice stone (SS White), G3= Micropol (DMC Equipment), G4= Opalustre (Ultradent) and G5= Whiteness RM (FGM Dental Products). Roughness and wear were the responsible variables used to analyze these surfaces in four stages: baseline, 60 s and 120 s after the micro-abrasion and after polishing, using a Hommel Tester T1000 device. After the tests, a normal distribution of data was verified, with repeated ANOVA analyses (p?0.05) which were used to compare each product in different stages. One-way ANOVA and Tukey tests were applied for individual comparisons between the products in each stage (p?0.05). Results: Means and standard deviations of roughness and wear (µm) after all the promoted stages were: G1=7.26(1.81)/13.16(2.67), G2=2.02(0.62)/37.44(3.33), G3=1.81(0.91)/34.93(6.92), G4=1.92(0.29)/38.42(0.65) and G5=1.98(0.53)/33.45(2.66). At 60 seconds, all products tended to produce less surface roughness with a variable gradual decrease over time. After polishing, there were no statistically significant differences between the groups, except for G1. Independent of the product utilized, the enamel wear occurred after the micro-abrasion. Conclusions: In this in vitro study, enamel micro-abrasion presented itself as a conservative approach, regardless of the type of the paste compound utilized. These products promoted minor roughness alterations and minimal wear. The use of phosphoric acid and pumice stone showed similar results to commercial products for the micro-abrasion with regard to the surface roughness and wear.

Associação de técnicas conservadoras para otimizar a estética do sorriso: clareamento dental e microabrasão do esmalte

As várias opções para a realização de tratamentos estéticos conservadores permitem ao profissional a escolha de materiais e técnicas apropriados, que melhor se enquadrem nas características individuais de cada paciente e na realidade de seu consultório. No caso clínico apresentado, a técnica de clareamento dental em consultório com peróxido de hidrogênio a 35% (Total Blanc Office, DFL), ativado com luz híbrida LED/LASER e a microabrasão de esmalte com pasta de acido fosfórico a 37% e pedra pomes, foram associados. Os resultados com o clareamento em consultório são imediatos, de forma que o profissional dispõe de total controle sobre aplicação do gel clareador em áreas e dentes específicos. A microabrasão do esmalte é um tratamento simples e custo relativamente baixo, remove as manchas superficiais do esmalte com preservação de estrutura dental. No caso apresentado, a associação das duas técnicas proporcionou a obtenção de excelente resultado estético em apenas uma sessão de atendimento.

Evaluation of fluid transport processes in dental enamel. Methods to assess the relevance of enamel permeability in caries prevention and etching treatments.

This thesis evaluated in vivo and in vitro enamel permeability in different physiological and clinical conditions by means of SEM inspection of replicas of enamel surface obtained from polyvinyl siloxane impressions subsequently later cast in polyether impression ma-terial. This technique, not invasive and risk-free, allows the evaluation of fluid outflow from enamel surface and is able to detect the presence of small quantities of fluid, visu-alized as droplets. Fluid outflow on enamel surface represents enamel permeability. This property has a paramount importance in enamel physiolgy and pathology although its ef-fective role in adhesion, caries pathogenesis and prevention today is still not fully under-stood. The aim of the studies proposed was to evaluate enamel permeability changes in differ-ent conditions and to correlate the findings with the actual knowledge about enamel physiology, caries pathogenesis, fluoride and etchinhg treatments. To obtain confirmed data the replica technique has been supported by others specific techniques such as Ra-man and IR spectroscopy and EDX analysis. The first study carried out visualized fluid movement through dental enamel in vivo con-firmed that enamel is a permeable substrate and demonstrated that age and enamel per-meability are closely related. Examined samples from subjects of different ages showed a decreasing number and size of droplets with increasing age: freshly erupted permanent teeth showed many droplets covering the entire enamel surface. Droplets in permanent teeth were prominent along enamel perikymata. These results obtained through SEM inspection of replicas allowed innovative remarks in enamel physiology. An analogous testing has been developed for evaluation of enamel permeability in primary enamel. The results of this second study showed that primary enamel revealed a substantive permeability with droplets covering the entire enamel sur-face without any specific localization accordingly with histological features, without changes during aging signs of post-eruptive maturation. These results confirmed clinical data that showed a higher caries susceptibility for primary enamel and suggested a strong relationship between this one and enamel permeability. Topical fluoride application represents the gold standard for caries prevention although the mechanism of cariostatic effect of fluoride still needs to be clarified. The effects of topical fluoride application on enamel permeability were evaluated. Particularly two dif-ferent treatments (NaF and APF), with different pH, were examined. The major product of topical fluoride application was the deposition of CaF2-like globules. Replicas inspec-tion before and after both treatments at different times intervals and after specific addi-tional clinical interventions showed that such globule formed in vivo could be removed by professional toothbrushing, sonically and chemically by KOH. The results obtained in relation to enamel permeability showed that fluoride treatments temporarily reduced enamel water permeability when CaF2-like globules were removed. The in vivo perma-nence of decreased enamel permeability after CaF2 globules removal has been demon-strated for 1 h for NaF treated teeth and for at least 7 days for APF treated teeth. Important clinical consideration moved from these results. In fact the caries-preventing action of fluoride application may be due, in part, to its ability to decrease enamel water permeability and CaF2 like-globules seem to be indirectly involved in enamel protection over time maintaining low permeability. Others results obtained by metallographic microscope and SEM/EDX analyses of or-thodontic resins fluoride releasing and not demonstrated the relevance of topical fluo-ride application in decreasing the demineralization marks and modifying the chemical composition of the enamel in the treated area. These data obtained in both the experiments confirmed the efficacy of fluoride in caries prevention and contribute to clarify its mechanism of action. Adhesive dentistry is the gold standard for caries treatment and tooth rehabilitation and is founded on important chemical and physical principles involving both enamel and dentine substrates. Particularly acid etching of dental enamel enamel has usually employed in bonding pro-cedures increasing microscopic roughness. Different acids have been tested in the litera-ture suggesting several etching procedures. The acid-induced structural transformations in enamel after different etching treatments by means of Raman and IR spectroscopy analysis were evaluated and these findings were correlated with enamel permeability. Conventional etching with 37% phosphoric acid gel (H3PO4) for 30 s and etching with 15 % HCl for 120 s were investigated. Raman and IR spectroscopy showed that the treatment with both hydrochloric and phosphoric acids induced a decrease in the carbonate content of the enamel apatite. At the same time, both acids induced the formation of HPO42- ions. After H3PO4 treatment the bands due to the organic component of enamel decreased in intensity, while in-creased after HCl treatment. Replicas of H3PO4 treated enamel showed a strongly reduced permeability while replicas of HCl 15% treated samples showed a maintained permeability. A decrease of the enamel organic component, as resulted after H3PO4 treatment, involves a decrease in enamel permeability, while the increase of the organic matter (achieved by HCl treat-ment) still maintains enamel permeability. These results suggested a correlation between the amount of the organic matter, enamel permeability and caries. The results of the different studies carried out in this thesis contributed to clarify and improve the knowledge about enamel properties with important rebounds in theoretical and clinical aspects of Dentistry.

Wasserfreie Protonenleiter für Brennstoffzellen auf der Basis von Imidazol und Benzimidazol

Mit Hilfe von Brennstoffzellen wird eine effiziente Energieumwandlung von chemischer in elektrische Energie möglich. Die kommerziellen PEM-Brennstoffzellen benutzen Membra-nen, die zum Erreichen hoher Leitfähigkeiten eine wässrige Phase erfordern, in der der Proto-nentransport stattfindet. Somit wird die Betriebstemperatur durch den Siedepunkt des Wassers limitiert. Die verwendeten Pt-Katalysatoren zeigen bei niedrigen Temperaturen eine höhere Empfindlichkeit gegenüber CO, dass im Reformierungsprozess bei der Erzeugung von Was-serstoff entsteht. Austausch der wässrigen Phase gegen Heterozyklen, die ein zu Wasser ver-gleichbares Wasserstoffbrückennetzwerk aufbauen, in dem der Protonentransport stattfinden kann, ermöglicht eine höhere Betriebstemperatur. Durch das im Laufe des Brennstoffzellen-betriebs gebildete Wasser, können die Heterozyklen verdünnt bzw. komplett aus der Memb-ran ausgewaschen werden. Daher ist es erforderlich, die Ladungsträger an ein Polymerrück-grat zu binden, so dass sie eine hohe Beweglichkeit und Konzentration, die denen in der flüs-sigen Phase einer konventionellen Membran entsprechen, aufweisen. Diese Arbeit beschreibt die Synthese und Charakterisierung von Protonenleitern, die ohne eine flüssige Phase auskommen, da sie bereits protonische Leitfähigkeit als intrinsische Ei-genschaft zeigen. Es wurden verschiedene imidazol- bzw. benzimidazolhaltige Dimere und Polythiophene, in denen Benzimidazol in der Seitenkette über verschieden flexible Spacer mit dem Polymerrückgrat verbunden ist, synthetisiert. Die Materialien wurden in undotierten Zu-stand und nach Dotierung mit geringen Mengen Phosphorsäure umfassend charakterisiert und auf thermisches Verhalten, Stabilität und Leitfähigkeit untersucht. Die benzimidazolhaltigen Dimere weisen mit 250 °C die höchsten Zersetzungstemperaturen auf. Mit zunehmender Temperatur kann in allen Fällen eine Erhöhung der Leitfähigkeit beobachtet werden, die sich in der Arrhenius-Auftragung durch eine Gerade anpassen lässt, somit kann der Protonentrans-port durch einen Protonen-hüpfmechanismus beschrieben werden. Die höchste beobachtete Leitfähigkeit liegt im Bereich von 10-6 S/cm bei 160 °C. Durch Zusatz von Phosphorsäure kann die Leitfähigkeit z.T. um einige Größenordnungen gesteigert werden. Eine Ausnahme bilden die Polythiophene, die sowohl protonische als auch elektronische Leitfähigkeit besit-zen. Hier führt die Säure zu einer Lokalisierung der Ladungsträger, so dass die elektronische Leitfähigkeit eingeschränkt wird.

Pyrolysis-Gas Chromatography-Mass Spectometry and Chemometric Analysis for the Characterization of Complex Matrices

The present PhD thesis was focused on the development and application of chemical methodology (Py-GC-MS) and data-processing method by multivariate data analysis (chemometrics). The chromatographic and mass spectrometric data obtained with this technique are particularly suitable to be interpreted by chemometric methods such as PCA (Principal Component Analysis) as regards data exploration and SIMCA (Soft Independent Models of Class Analogy) for the classification. As a first approach, some issues related to the field of cultural heritage were discussed with a particular attention to the differentiation of binders used in pictorial field. A marker of egg tempera the phosphoric acid esterified, a pyrolysis product of lecithin, was determined using HMDS (hexamethyldisilazane) rather than the TMAH (tetramethylammonium hydroxide) as a derivatizing reagent. The validity of analytical pyrolysis as tool to characterize and classify different types of bacteria was verified. The FAMEs chromatographic profiles represent an important tool for the bacterial identification. Because of the complexity of the chromatograms, it was possible to characterize the bacteria only according to their genus, while the differentiation at the species level has been achieved by means of chemometric analysis. To perform this study, normalized areas peaks relevant to fatty acids were taken into account. Chemometric methods were applied to experimental datasets. The obtained results demonstrate the effectiveness of analytical pyrolysis and chemometric analysis for the rapid characterization of bacterial species. Application to a samples of bacterial (Pseudomonas Mendocina), fungal (Pleorotus ostreatus) and mixed- biofilms was also performed. A comparison with the chromatographic profiles established the possibility to: • Differentiate the bacterial and fungal biofilms according to the (FAMEs) profile. • Characterize the fungal biofilm by means the typical pattern of pyrolytic fragments derived from saccharides present in the cell wall. • Individuate the markers of bacterial and fungal biofilm in the same mixed-biofilm sample.

Anhydrous proton conducting polymer electrolytes based on polymeric ionic liquids

Imidazolium types of ionic liquids were immobilized by tethering it to acrylate backbone. These imidazolium salt containing acrylate monomers were polymerize at 70oC by free radical polymerization to give polymers poly(AcIm-n) with n being the side chain lenght. The chemical structure of the polymer electrolytes obtained by the described synthetic routes was investigated by NMR-spectroscopy. The polymers were doped with various amounts of H3PO4 and LiN(SO2CF3)2, to obtain poly(AcIm-n) x H3PO4 and poly(AcIm-2-Li) x LiN(SO2CF3)2. The TG curves show that the polymer electrolytes are thermally stable up to about 200◦C. DSC results indicates the softening effect of the length of the spacers (n) as well as phosphoric acid. The proton conductivity of the samples increase with x and reaches to 10-2 Scm-1 at 120oC for both poly(AcIm-2)2H3PO4 and poly(AcIm-6)2H3PO4. It was observed that the lithium ion conductivity of the poly(AcIm-2-Li) x LiN(SO2CF3)2 increases with blends (x) up to certain composition and then leveled off independently from blend content. The conductivity reaches to about 10-5 S cm-1 at 30oC and 10-3 at 100oC for poly(AcIm-2-Li) x LiN(SO2CF3)2 where x is 10. The phosphate and phosphoric acid functionality in the resulting polymers, poly(AcIm-n) x H3PO4, undergoes condensation leading to the formation of cross-linked materials at elevated temperature which may improve the mechanical properties to be used as membrane materials in fuel cells. High resolution nuclear magnetic resonance (NMR) spectroscopy was used to obtain information about hydrogen bonding in solids. The low Tg enhances molecular mobility and this leads to better resolved resonances in both the backbone region and side chain region. The mobile and immobile protons can be distinguished by comparing 1H MAS and 1H-DQF NMR spectra. The interaction of the protons which may contribute to the conductivity is observed from the 2D double quantum correlation (DQC) spectra.

Entwicklung und Anwendung massenspektrometrischer Methoden zur Spurenanalytik iodhaltiger Verbindungen und aliphatischer Amine in der marinen Umwelt

In der marinen Grenzschicht beeinflussen reaktive Iodspezies wie z.B. I2 sowie aliphatische Amine eine Vielzahl atmosphärischer Prozesse, vor allem bei der Partikelneubildung spielen sie eine entscheidende Rolle. Allerdings stellt die Quantifizierung dieser Verbindungen im Spurenbereich immer noch eine große analytische Herausforderung dar. rnAus diesem Grund wurde im Rahmen der vorliegenden Arbeit das GTRAP-AMS (Gaseous compound trapping in artificially generated particles – aerosol mass spectrometry) entwickelt, um gasförmiges I2 und aliphatische Amine zu bestimmen. Hierbei wird ein Flugzeit-Aerosolmassenspektrometer (ToF-AMS), das ursprünglich für die on-line Charakterisierung von Aerosolen entwickelt wurde, mit einer GTRAP-Einheit gekoppelt. Im Fall von I2 werden mit Hilfe eines pneumatischen Zerstäubers a-Cyclodextrin/NH4Br-Partikel erzeugt, die mit dem gasförmigen I2 innerhalb der GTRAP-Einheit eine Einschlussverbindung bilden und dieses dadurch selektiv in die Partikelphase aufnehmen. Für die on-line Bestimmung gasförmiger aliphatischer Amine dagegen wurde Phosphorsäure als partikulärer Reaktionspartner eingesetzt. Nach Optimierung des GTRAP-AMS Systems wurde sowohl für I2 als auch für die aliphatischen Amine eine Nachweisgrenze im sub-ppb-Bereich für eine Zeitauflösung zwischen 1 und 30 min erhalten. Als erstes wurde das GTRAP-AMS System zur Charakterisierung von Permanentdenudern eingesetzt, um deren I2-Aufnahmefähigkeit und Wiederverwendbarkeit im Vergleich zu den herkömmlichen einmal verwendbaren a-Cyclodextrin Denudern zu testen.rnIm Anschluss daran wurde das GTRAP-AMS für die Bestimmung zeitlich aufgelöster I2- Emissionsraten ausgewählter Makroalgen unter dem Einfluss von Ozon eingesetzt. Die Kenntnis der Emissionsraten iodhaltiger Verbindungen der wichtigsten weltweit vorkommenden Makroalgen ist für die Modellierung der Iodchemie in der marinen Grenzschicht von besonderer Bedeutung. Die Resultate zeigen, dass verschiedene Makroalgen sowohl unterschiedliche zeitlich aufgelöste I2-Emissionsprofile als auch Gesamtemissionsraten liefern. Im Vergleich zu den iodorganischen Verbindungen ist die Gesamtemissionsrate an I2 allerdings eine bis zwei Größenordnungen größer. Dies und die deutlich kürzere atmosphärische Lebensdauer von I2 im Vergleich zu den iodorganischen Verbindungen führen dazu, dass I2 die dominierende iodhaltige Verbindung für die Bildung reaktiver Iodatome in der marinen Grenzschicht ist. rnDa über dem tropischen Atlantischen Ozean bislang jedoch nur ein geringer Anteil der IO-Konzentration durch die Oxidation von iodorganischen Verbindungen erklärt werden kann, wurden weitere Quellen für I2 erforscht. Deshalb wurden Kammerexperimente mit Mikrolagen durchgeführt, um deren Einfluss auf die I2-Freisetzung in die Atmosphäre zu untersuchen. Hierbei konnte gezeigt werden, dass die Anwesenheit von Mikroalgen (z.B. Coscinodiscus Wailesii) im Meerwasser zu einer erhöhten Freisetzung von I2 aus dem Meerwasser in die Atmosphäre führen kann. rnDes Weiteren wurden auch Versuche zu abiotischen Bildungswegen von I2 durchgeführt. Die Ergebnisse der Atmosphärensimulationsexperimente haben gezeigt, dass partikuläre Iodoxide durch organische Verbindungen zu I2 reduziert werden können, welches im Anschluss von der Partikelphase in die Gasphase übergehen kann und dort wieder für Gasphasenprozesse zur Verfügung steht.rn

Einsatz eines Aerosolmassenspektrometers während der CYPHEX-Kampagne und zur Methodenentwicklung einer Echtzeitquantifizierung gasförmiger Amine

Atmosphärische Aerosole haben einen starken Einfluss auf das Klima, der bisher nur grundlegend verstanden ist und weiterer Forschung bedarf. Das atmosphärische Verhalten der Aerosolpartikel hängt maßgeblich von ihrer Größe und chemischen Zusammensetzung ab. Durch Reflexion, Absorption und Streuung des Sonnenlichtes verändern sie den Strahlungshaushalt der Erde direkt und durch ihre Einflussnahme auf die Wolkenbildung indirekt. Besonders gealterte, stark oxidierte organische Aerosole mit großem Sauerstoff-zu-Kohlenstoff-Verhältnis wirken als effektive Wolkenkondensationskeime. Neben primären Aerosolpartikeln, die direkt partikelförmig in die Atmosphäre gelangen, spielen sekundäre Aerosolpartikel eine große Rolle, die aus Vorläufergasen in der Atmosphäre entstehen. Aktuelle Forschungsergebnisse legen nahe, dass kurzkettige aliphatische Amine bei Nukleationsprozessen beteiligt sind und somit die Partikelneubildung vielerorts mitsteuern. Um die Rolle von Aminen in der Atmosphäre besser erforschen und industrielle Emissionen kontrollieren zu können, bedarf es einer zuverlässigen Methode zur Echtzeitquantifizierung gasförmiger Amine mit hoher Zeitauflösung und niedriger Nachweisgrenze.rnDas hochauflösende Flugzeit-Aerosolmassenspektrometer (HR-ToF-AMS) bietet die Möglichkeit, atmosphärische Partikel in Echtzeit zu analysieren. Dabei werden Größe, Menge und grundlegende chemische Zusammensetzung erfasst. Anorganische Aerosolbestandteile können eindeutig zugeordnet werden. Es ist jedoch kaum möglich, einzelne organische Verbindungen in den komplizierten Massenspektren atmosphärischer Aerosole zu identifizieren und quantifizieren.rnIn dieser Arbeit wird atmosphärisches Aerosol untersucht, das im Westen Zyperns während der CYPHEX-Kampagne mit einem HR-ToF-AMS gemessen wurde. An diesem Standort ist vor allem stark gealtertes Aerosol vorzufinden, das aus Zentral- und Westeuropa stammt. Lokale Einflüsse spielen fast keine Rolle. Es wurde eine durchschnittliche Massenkonzentration von 10,98 μg/m3 gefunden, zusammengesetzt aus 57 % Sulfat, 30 % organischen Bestandteilen, 12 % Ammonium, < 1 % Nitrat und < 1 % Chlorid, bezogen auf das Gewicht. Der Median des vakuum-aerodynamischen Durchmessers betrug 446,25 nm. Es wurde sehr acides Aerosol gefunden, dessen anorganische Bestandteile weitgehend der Zusammensetzung von Ammoniumhydrogensulfat entsprachen. Tag-Nacht-Schwankungen in der Zusammensetzung wurden beobachtet. Die Sulfatkonzentration und die Acidität zeigten tagsüber Maxima und nachts Minima. Konzentrationsschwankungen an Nitrat und Chlorid zeigten einen weniger ausgeprägten Rhythmus, Maxima fallen aber immer mit Minima der Sulfatkonzentration, Aerosolacidität und Umgebungstemperatur zusammen. Organische Aerosolbestandteile entsprachen stark gealtertem, schwerflüchtigem oxidiertem organischem Aerosol. Es wurde eine interne Mischung der Partikel beobachtet, die ebenfalls meist bei alten Aerosolen auftritt.rnUm mit dem HR-ToF-AMS auch einzelne organische Verbindungen identifizieren und quantifizieren zu können, wurde eine Methode entwickelt, mit der man Amine der Gasphase selektiv in künstlich erzeugte Phosphorsäurepartikel aufnimmt und so für die HR-ToF-AMS-Messung zugänglich macht. Dadurch kombiniert man die Vorteile der Online-Messung des HR-ToF-AMS mit den Vorteilen klassischer Offline-Probenahmen. So können in Echtzeit sehr einfache Massenspektren gemessen werden, in denen störende Komponenten abgetrennt sind, während die Analyten eindeutig identifiziert werden können. Systeme dieser Art wurden GTRAP-AMS (Gaseous compound TRapping in Artificially-generated Particles – Aerosol Mass Spectrometry) genannt. Kalibrierungen für (Mono)Methylamin, Dimethylamin, Trimethylamin, Diethylamin und Triethylamin ergaben Nachweisgrenzen im ppt-Bereich bei einer Zeitauflösung von 3 min. Kammerexperimente zur Aminemission von Pflanzen zeigten eine gute Übereinstimmung des neu entwickelten Systems mit einer Gasdiffusionsabscheider-Offline-Probenahme und anschließender ionenchromatographischer Analyse. Beide Methoden zeigten Reaktionen der Pflanzen auf eine Veränderung der Lichtverhältnisse, während erhöhte Ozonkonzentrationen die Aminemission nicht veränderten. Die GTRAP-AMS-Methode eignet sich bereits für die Messung von Umgebungsluftkonzentrationen an einigen Orten, für die meisten Orte reicht die Nachweisgrenze allerdings noch nicht aus. Die Technik könnte bereits zur Echtzeitkontrolle industrieller Abgasemissionen eingesetzt werden.

Enantioselective capillary electrophoresis for the assessment of CYP3A4-mediated ketamine demethylation and inhibition in vitro

Enantioselective CE with sulfated cyclodextrins as chiral selectors was used to determine the CYP3A4-catalyzed N-demethylation kinetics of ketamine to norketamine and its inhibition in the presence of ketoconazole in vitro. Ketamine, a chiral phencyclidine derivative, was incubated with recombinant human CYP3A4 from a baculovirus expression system as racemic mixture and as single enantiomer. Alkaline liquid/liquid extracts of the samples were analyzed with a pH 2.5 buffer comprising 50 mM Tris and phosphoric acid together with either multiple isomer sulfated β-cyclodextrin (10 mg/mL) or highly sulfated γ-cyclodextrin (2%, w/v). Data obtained in the absence of ketoconazole revealed that the N-demethylation occurred stereoselectively with Michaelis-Menten (incubation of racemic ketamine) and Hill (separate incubation of single enantiomers) kinetics. Data generated in the presence of ketoconazole as the inhibitor could best be fitted to a one-site competitive model and inhibition constants were calculated using the equation of Cheng and Prusoff. No stereoselective difference was observed, but inhibition constants for the incubation of racemic ketamine were found to be larger compared with those obtained with the incubation of single ketamine enantiomers.

High-resolution computer simulation of the dynamics of isoelectric focusing using carrier ampholytes: focusing with concurrent electrophoretic mobilization is an isotachophoretic process

Focusing of four hemoglobins with concurrent electrophoretic mobilization was studied by computer simulation. A dynamic electrophoresis simulator was first used to provide a detailed description of focusing in a 100-carrier component, pH 6-8 gradient using phosphoric acid as anolyte and NaOH as catholyte. These results are compared to an identical simulation except that the catholyte contained both NaOH and NaCl. A stationary, steady-state distribution of carrier components and hemoglobins is produced in the first configuration. In the second, the chloride ion migrates into and through the separation space. It is shown that even under these conditions of chloride ion flux a pH gradient forms. All amphoteric species acquire a slight positive charge upon focusing and the whole pattern is mobilized towards the cathode. The cathodic gradient end is stable whereas the anodic end is gradually degrading due to the continuous accumulation of chloride. The data illustrate that the mobilization is a cationic isotachophoretic process with the sodium ion being the leading cation. The peak height of the hemoglobin zones decreases somewhat upon mobilization, but the zones retain a relatively sharp profile, thus facilitating detection. The electropherograms that would be produced by whole column imaging and by a single detector placed at different locations along the focusing column are presented and show that focusing can be commenced with NaCl present in the catholyte at the beginning of the experiment. However, this may require detector placement on the cathodic side of the catholyte/sample mixture interface.

Temporary zinc oxide-eugenol cement: eugenol quantity in dentin and bond strength of resin composite

Uptake of eugenol from eugenol-containing temporary materials may reduce the adhesion of subsequent resin-based restorations. This study investigated the effect of duration of exposure to zinc oxide–eugenol (ZOE) cement on the quantity of eugenol retained in dentin and on the microtensile bond strength (μTBS) of the resin composite. The ZOE cement (IRM Caps) was applied onto the dentin of human molars (21 per group) for 1, 7, or 28 d. One half of each molar was used to determine the quantity of eugenol (by spectrofluorimetry) and the other half was used for μTBS testing. The ZOE-exposed dentin was treated with either OptiBond FL using phosphoric acid (H3PO4) or with Gluma Classic using ethylenediaminetetraacetic acid (EDTA) conditioning. One group without conditioning (for eugenol quantity) and two groups not exposed to ZOE (for eugenol quantity and μTBS testing) served as controls. The quantity of eugenol ranged between 0.33 and 2.9 nmol mg−1 of dentin (median values). No effect of the duration of exposure to ZOE was found. Conditioning with H3PO4 or EDTA significantly reduced the quantity of eugenol in dentin. Nevertheless, for OptiBond FL, exposure to ZOE significantly decreased the μTBS, regardless of the duration of exposure. For Gluma Classic, the μTBS decreased after exposure to ZOE for 7 and 28 d. OptiBond FL yielded a significantly higher μTBS than did Gluma Classic. Thus, ZOE should be avoided in cavities later to be restored with resin-based materials.

Effect of tin-chloride pretreatment on bond strength of two adhesive systems to dentin

OBJECTIVES: To determine the effect on resin composite-to-dentin bond strength of incorporation of an acidic tin-chloride pretreatment in two adhesive systems. MATERIALS AND METHODS: Human molars were ground to expose mid-coronal dentin. For microtensile bond strength (μTBS) testing, dentin was treated with Optibond FL or Clearfil SE according to one of six protocols (n = 22/group). Group 1: Phosphoric acid etching, Optibond FL Prime, Optibond FL Adhesive (manufacturer's instructions; control); Group 2: Tin-chloride pretreatment, Optibond FL Prime, Optibond FL Adhesive; Group 3: Phosphoric acid etching, tin-chloride pretreatment, Optibond FL Prime, Optibond FL Adhesive; Group 4: Clearfil SE Primer, Clearfil SE Bond (manufacturer's instructions; control); Group 5: Phosphoric acid etching, Clearfil SE Primer, Clearfil SE Bond; and Group 6: Tin-chloride pretreatment, Clearfil SE Primer, Clearfil SE Bond. The molars were then built up with resin composite (Clearfil Majesty Esthetic). After storage (1 week, 100  % humidity, 37 °C) the μTBS was measured and failure mode was determined. Additionally, pretreated dentin surfaces were evaluated using SEM and EDX. The μTBS results were analyzed statistically by a Welch Two Sample t-test and a Kruskal-Wallis test followed by exact Wilcoxon rank sum tests with Bonferroni-Holm adjustment for multiple testing (α = 0.05). RESULTS: When Optibond FL was used, partial or total replacement of phosphoric acid with tin-chloride decreased μTBS significantly. In contrast, when Clearfil SE was used, inclusion of a tin-chloride pretreatment in the adhesive procedure increased μTBS significantly. CONCLUSIONS: Tin-chloride pretreatment had a beneficial influence on the bond promoting capacity of the MDP-containing adhesive system Clearfil SE.

A versatile gas interface for routine radiocarbon analysis with a gas ion source

In 2010 more than 600 radiocarbon samples were measured with the gas ion source at the MIni CArbon DAting System (MICADAS) at ETH Zurich and the number of measurements is rising quickly. While most samples contain less than 50 mu g C at present, the gas ion source is attractive as well for larger samples because the time-consuming graphitization is omitted. Additionally, modern samples are now measured down to 5 per-mill counting statistics in less than 30 min with the recently improved gas ion source. In the versatile gas handling system, a stepping-motor-driven syringe presses a mixture of helium and sample CO2 into the gas ion source, allowing continuous and stable measurements of different kinds of samples. CO2 can be provided in four different ways to the versatile gas interface. As a primary method. CO2 is delivered in glass or quartz ampoules. In this case, the CO2 is released in an automated ampoule cracker with 8 positions for individual samples. Secondly, OX-1 and blank gas in helium can be provided to the syringe by directly connecting gas bottles to the gas interface at the stage of the cracker. Thirdly, solid samples can be combusted in an elemental analyzer or in a thermo-optical OC/EC aerosol analyzer where the produced CO2 is transferred to the syringe via a zeolite trap for gas concentration. As a fourth method, CO2 is released from carbonates with phosphoric acid in septum-sealed vials and loaded onto the same trap used for the elemental analyzer. All four methods allow complete automation of the measurement, even though minor user input is presently still required. Details on the setup, versatility and applications of the gas handling system are given. (C) 2012 Elsevier B.V. All rights reserved.