Manejo químico de espécies de trapoeraba com aplicação isolada e em mistura de diferentes herbicidas

This paper evaluated the effect of different herbicides applied isolated and mixed on two species of dayflower (Commelina benghalensis and Commelina villosa). Both species were grown under pot conditions with a capacity of 14 L. Three stems with 10 cm were planted per pot. The herbicides application was made using a stationary spray system, to provide a spray volume of 200 L ha(-1), with spray tip XR 110.02VS, when the plants were with dimensions of 25-35 cm for C. benghalensis and 30-35 cm for C. villosa. The mixture saflufenacil more effective control of C. benghalensis were saflufenacil + glyphosate (48 + 720 g ha(-1)) and, saflufenacil + (glyphosate + imazethapyr) with and without the addition of ammonium sulfate (24 + 623 g ha(-1)). The combination of carfentrazone + glyphosate (20 + 720 g ha(-1)) were also effective in the C. benghalensis control. The saflufenacil mixture allowed plant control of C. villosa, where saflufenacil + glyphosate (24 + 720 g ha(-1)) with the addition of ammonium sulfate, showed a good visually control of this species. The application of 2,4-D (720 g ha(-1)) and 2,4-D + glyphosate (720 + 720 g ha(-1)) provided the best visual controls of C. benghalensis e C. villosa. All chemical treatment regardless of Commelina species reduced the dry mass of dayflower.

Produção de grês porcelanato a partir de matérias-primas do Rio Grande do Norte e queima a gás natural

The State of Rio Grande do Norte, Brazil, possess major deposits of feldspar, clay, kaolin and talc, all raw materials used in the production of porcelainized stoneware tiles. Conversely, state industries manufacture only low added value red ceramics. Porcelainized stoneware tiles is one of the noblest ceramics, depicting low water absorption (typically below of 0,5%), in addition to excellent staining resistance and mechanical strength. The present work aims at investigating the potential of local raw materials for the production of porcelainized stoneware tiles. To that end, these materials were characterized by X-ray fluorescence, X-ray diffraction, particle size analysis, thermal gravimetric analysis and thermal differential analysis. Admixtures containing different compositions were prepared and fired at three temperatures, 1150, 1200 and 1250°C for 30 min. After firing, tests samples were characterized by water absorption tests, linear retraction, dilatometric analysis, apparent porosity, apparent specific mass, flexural strength, and microstructural analysis by XRD and SEM. The results revealed that ceramics with porcelainized stoneware tiles characteristics could be produced from raw materials originated in the State of Rio Grande do Norte

Estudo do potencial de utilização do resíduo da extração de esmeraldas na fabricação de cerâmica de revestimento

Companies involved in emerald mining and treatment represent an important area of industrial development in Brazil, with significative contribution to the worldwide production of such mineral. As a result, large volumes of emerald waste are constantly generated and abandoned in the environment, negatively contributing to its preservation. By the other side the interest of the use of mining waste as additive in ceramic products has been growing from researchers in recent years. The ceramic industry is constantly seeking to the marked amplification for the sector and perfecting the quality of the products and to increase the variety of applications. The technology of obtaining of ceramic tiles that uses mining residues assists market niches little explored. In this scenario, the objective of the present study was to characterize the residue generated from emerald mining as well as to assess its potential use as raw material for the production of ceramic tiles. Ceramic mixtures were prepared from raw materials characterized by X-ray fluorescence, X-ray diffraction, particle size analysis and thermal analysis. Five compositions were prepared using emerald residue contents of 0%, 10%, 20%, 30% and 40%. Samples were uniaxially pressed, fired at 1000, 1100 and 1200ºC and characterized aiming at establishing their mineralogical composition, water absorption, apparent porosity, specific mass, linear retraction and modulus of rupture. The results shows that the emerald residue, basically consisted of 73% of (SiO2 + Al2O3) and 17,77% of (MgO + Na2O+ K2O) (that facilitates sintering), can be added to the ceramic tile materials with no detrimental effect on the properties of the sintered products

Avaliação do processo industrial da cerâmica vermelha na região do Seridó - RN

Particularly in Braziland in Rio Grande do Norte, companies manufacturing red ceramic, play an important role as agents of development to study the region Seridó- RN, specific place for carrying out the research. It is observed in this region a concentration of red ceramic industries of small size, which, despite its importance in the ceramic, they are unable to enjoy or use the new forms of administrative management and technological advances designed and offered by universities, centers of research and projects of governments, remained almost entirely outside the progress and modernization, technological and administrative. These companies still have outdated technology, and management processes, providing quality problems and standardization of end products. Upon these conditions are the companies going through crisis and struggling to survive alone and without assistance. The region of Seridó-RN, lets make a detailed case study of red ceramic companies in the region proposed from the existing theoretical and actual lifting of the condition of the product manufacturing red ceramic, allowing through this overview of the implementation of collect samples of raw materials, allowing the study of each ceramic industry that contributed to the participation of the research, which was determined parameters such as: analysis of the physical, chemical and technological properties of raw materials, characterization of the processes used, raising the technological resources considering equipment, machinery, supplies, raw materials and facilities available and its organization by type of products from companies involved in this study. The methodology consists of the following steps: collection of raw material, crushing and screening, characterization of raw materials (liquid limit, chemical analysis, mineralogical analysis, differential thermal analysis, sieve analysis), mixing, forming, cutting, drying and burning of ceramic bodies and bodies of evidence. The results showed that it was clay with distinct characteristics with respect to plasticity. With respect to the different compositions of mixtures of ceramic masses, we conclude that the ceramic properties showed a direct proportionality with increasing fraction of the clay not plastic. However, the compositions of the masses studied proved to be the most appropriate for the types of simulated clay for use in ceramics. Adopted in the ceramic processing made it possible to obtain products the resulted in consistent properties, and in some cases even exceeding the requirements of technical studies and standard-Brazilian clays to obtain ceramic products such as tiles, bricks and tiles to floor. Based on the discussions from the results obtained in the various processing steps of this work, one can draw conclusions according to the physico-chemical and mineralogical properties of raw materials, the properties of ceramic products burned and analysis. This work may be used by other researchers, private companies and governmental organizations, undergraduate students and graduate, can develop studies and future research to: develop projects to modify the furnaces; mapping projects develop and rationalize the exploitation of raw materials ;promoting reforestation and forest management; develop reduction projects and recovery of waste; develop training projects in manpower sector, and develop security projects, improving the conditions of work in the area pottery

Performance comparativa entre R290/R600a (50:50) e R134a para drop-in em refrigerador doméstico

This research this based on the seminar on Use of Natural Fluids in Refrigeration and Air-Conditioning Systems conducted in 2007 in Sao Paulo. The event was inserted in the National Plan for Elimination of CFCs, coordinated by the Ministry of Environment and implemented by the United Nations Development Programme (UNDP). The objective of this research is analyze the performance of the hydrocarbons application as zeotropic mixtures in domestic refrigerator and validate the application of technical standards for pull down and cycling (on-off) tests to the mixture R290/R600a (50:50) in domestic refrigerator. It was first developed an computational analysis of R290/R600a (50:50) compared to R134a and other mass fractions of the hydrocarbons mixtures in the standard ASHRAE refrigeration cycle in order to compare the operational characteristics and thermodynamic properties of fluids based on the software REFPROP 6.0. The characteristics of the Lorenz cycle is presented as an application directed to zeotropic mixtures. Standardized pull down and cycling (on-off) tests were conducted to evaluate the performance of the hydrocarbons mixture R290/R600a (50:50) as a drop-in alternative to R134a in domestic refrigerator of 219 L. The results showed that the use of R290/R600a (50:50) with a charge of refrigerant reduced at 53% compared to R134a presents reduced energy performance than R134a. The COP obtained with hydrocarbon mixture was about 13% lower compared to R134a. Pull down times in the refrigerator compartments for fluids analyzed were quite close, having been found a 4,7% reduction in pull down time for the R290/R600a compared to R134a, in the freezer compartment. The data indicated a higher consumption of electric current from the refrigerator when operating with the R290/R600a. The values were higher than about 3% compared to R134a. The charge of 40 g of R290/R600a proved very low for the equipment analyzed

Análise da lubricidade do biodiesel brasileiro de ésteres etílicos de soja e girassol

Fuel is a material used to produce heat or power by burning, and lubricity is the capacity for reducing friction. The aim of this work is evaluate the lubricity of eight fossil and renewable fuels used in Diesel engines, by means of a HFRR tester, following the ASTM D 6079-04 Standard. In this conception, a sphere of AISI 52100 steel (diameter of 6,000,05 mm, Ra 0,050,005 μm, E = 210 GPa, HRC 624, HV0,2 63147) is submitted to a reciprocating motion under a normal load of 2 N and 50 Hz frequency to promote a wear track length of 1.10.1mm in a plan disc of AISI 52100 steel (HV0,05 18410, Ra 0,020,005 μm). The testing extent time was 75 minutes, 225,000 cycles. Each one test was repeated six times to furnish the results, by means of intrinsic signatures from the signals of the lubricant film percentage, friction coefficient, contact heating, Sound Pressure Level, SPL [dB]. These signal signatures were obtained by two thermocouples and a portable decibelmeter coupled to a data acquisition system and to the HFRR system. The wettability of droplet of the diesel fuel in thermal equilibrium on a horizontal surface of a virgin plan disc of 52100 steel, Ra 0,02  0,005 μm, were measured by its contact angle of 7,0  3,5o, while the results obtained for the biodiesel B5, B20 and B100 blends originated by the ethylic transesterification of soybean oil were, respectively, 7,5  3,5o, 13,5  3,5o e 19,0  1,0o; for the distilled water, 78,0  6,0o; the biodiesel B5, B20 and B100 blends originated by the ethylic transesterification of sunflower oil were, respectively, 7,0  4,0o, 8,5  4,5o e 19,5  2,5o. Different thickness of lubricant film were formed and measured by their percentage by means of the contact resistance technique, suggesting several regimes, since the boundary until the hydrodynamic lubrication. All oils analyzed in this study promoted the ball wear scars with diameters smaller than 400 μm. The lowest values were observed in the scar balls lubricated by mixtures B100, B20 and B5 of sunflower and B20 and B5 of soybean oils (WSD < 215 μm)

Estudo do potencial refratário de argilas sílico-aluminosas do Rio Grande do Norte

The segment of the structural ceramics industry is one of the most important to the economy of Rio Grande do Norte. The supply chain makes a total of 206 companies that are distributed in 39 counties, concentrated in three regional centers: Seridó Apodi / Assu and great Natal. The ceramic industry in the state is around 80 million pieces per month, with 50,186 million of these tiles, which makes the Rio Grande do Norte one of the largest manufacturers of product in the Country. Different ceramic products can be manufactured by mixing two or more clays and accessory minerals. Mixtures acquire characteristics and form what is called the ceramic body. Refractory masses have a high melting point and thermal shock support. Its composition contains refractory clays with a little iron oxide and material fluxes. A line of semi-refractory ceramic products that stands out for its high added value are the bricks in ivory or red, used in building barbecues, fireplaces, wood stoves and braziers. The aim of this study was to use alumina-clay or silica- alumina-clay to the industrial RN, for the production of refractory bricks semi-refractory burning light. Clay and Kaolin were characterized for their chemical and mineralogical composition, immediately after ceramic bodies were made with different concentrations of the components, they were raised, pressed and sintered. After sintering the resulting products were characterized in terms of mechanical, thermal and dimensional than the characterization by X-ray diffraction and scanning electron microscopy. After obtaining the results, we concluded that the studied clay can be used for the production of semi-refractory bricks

Seletividade de herbicidas em variedades de cana-de-açúcar

Este trabalho teve como objetivo avaliar a seletividade do herbicida topramezone aplicado de forma isolada e em mistura com tebuthiuron, em pós-emergência inicial, sobre dez variedades de cana-de-açúcar em condição de cana-planta. Os tratamentos utilizados foram: topramezone + Dash® (70 g ha-1 + 0,25% v/v); topramezone + tebuthiuron + Dash® (70 + 1.000 g ha-1 + 0,25% v/v); topramezone + tebuthiuron + Dash® (100 + 1.000 g ha-1 + 0,25% v/v); e ametryn + tebuthiuron (1.500 + 1.000 g ha-1), aplicados aos 35 dias após o plantio, além de uma testemunha sem aplicação de herbicidas. Durante a condução do experimento, todas as parcelas permaneceram livres da interferência das plantas daninhas por meio de capinas. As plantas de cana-de-açúcar estavam com duas a quatro folhas por ocasião da aplicação dos herbicidas. O delineamento experimental utilizado foi o de blocos casualizados em parcelas subdivididas, com quatro repetições, sendo as variedades dispostas nas parcelas e os herbicidas nas subparcelas. As variedades utilizadas foram: SP 83 2847, SP 80 3280, RB 85 5453, SP 80 1842, SP 89 1115, RB 86 7515, PO 8862, RB 85 5156, SP 80 1816 e SP 81 3250. As avaliações visuais de fitotoxicidade foram realizadas aos 7, 14, 28 e 35 dias após a aplicação. Ao final do estudo foram determinados os parâmetros tecnológicos pol, fibra e brix e os parâmetros produtivos rendimento de colmos e produção de açúcar. A formulação isolada de topramezone seguida de suas misturas com tebuthiuron proporcionaram inicialmente severos sintomas visuais de injúrias às plantas de cana-de-açúcar; contudo, as plantas de todas as variedades testadas tiveram uma total recuperação visual a partir dos 35 dias após a aplicação dos herbicidas. A mistura de tebuthiuron com topramezone reduziu os sintomas de injúrias iniciais provocados por este último. A mistura de ametryn + tebuthiuron foi o tratamento que evidenciou a ação fitotóxica menos severa às plantas, independentemente da variedade estudada. Nenhum dos herbicidas testados afetou negativamente os componentes tecnológicos e produtivos, sendo as diferenças observadas dependentes apenas das variedades. Podem-se considerar seletivos os herbicidas utilizados sobre as variedades avaliadas de cana-de-açúcar.

Avaliação e modelagem reológica de fluido de perfuração base água

The determination of the rheology of drilling fluids is of fundamental importance to select the best composition and the best treatment to be applied in these fluids. This work presents a study of the rheological behavior of some addictives used as viscosifiers in water-based drilling fluids. The evaluated addictives were: Carboxymethylcellulose (CMC), Xanthan gum (GX), and Bentonite. The main objective was to rheologically characterize suspensions composed by these addictives, by applying mathematical models for fluid flow behavior, in order to determine the best flow equation to represent the system, as well as the model parameters. The mathematical models applied in this research were: the Bingham Model, the Ostwald de Wale Model, and the Herschel-Bulkley Model. A previous study of hydration time for each used addictive was accomplished seeking to evaluate the effect of polymer and clay hydration on rheological behavior of the fluid. The rheological characterization was made through typical rheology experiments, using a coaxial cylinder viscosimeter, where the flow curves and the thixotropic magnitude of each fluid was obtained. For each used addictive the rheological behavior as a function of temperature was also evaluated as well as fluid stability as a function of the concentration and kind of addictive used. After analyses of results, mixtures of polymer and clay were made seeking to evaluate the rheological modifications provided by the polymer incorporation in the water + bentonite system. The obtained results showed that the Ostwald de Waale model provided the best fit for fluids prepared using CMC and for fluids with Xanthan gum and Bentonite the best fit was given by the Herschel-Bulkley one

Alteração fisiológica da cana-de-açúcar pela aplicação de Glyphosate e Sulfumeturon-Methyl

O bloqueio parcial das rotas onde atuam os herbicidas, com uso de baixas doses, pode ter implicações importantes, como a alteração do balanço de processos metabólicos nas plantas. Assim, foi conduzido no ano agrícola 2006/2007 um experimento em cana-soca de segundo corte na Fazenda Jurema, pertencente ao grupo COSAN, município de Barra Bonita-SP, para verificar os efeitos do glyphosate e do sulfumeturon-methyl, em subdoses, no comportamento fisiológico da cana-de-açúcar pelos níveis de clorofila e carotenoides. Os tratamentos constituíram-se da aplicação de dois herbicidas: sulfumeturon-methyl (Curavial 360 e.a. kg-1) e glyphosate (Roundup 480 i.a. kg-1), isolados e em misturas, em diferentes doses, e um tratamento controle, sem a aplicação dos herbicidas. As doses utilizadas foram: glyphosate 200 mL p.c. ha-1; glyphosate 400 mL p.c. ha -1; glyphosate 200 mL p.c. ha -1 + 10 g p.c. ha-1 de sulfumeturon-methyl; glyphosate 150 mL p.c. ha -1 + 12 g p.c. ha -1 de sulfumeturon-methyl; e sulfumeturon-methyl 20 g p.c. ha -1. O delineamento experimental utilizado foi o de blocos casualizados, com quatro repetições. As avaliações foram realizadas 15 e 30 dias após o plantio (DAP) e 30, 60, 90, 120, 150 e 180 dias após a colheita (DAC). As folhas foram cortadas padronizando-se o mesmo peso e área foliar. Para determinação do conteúdo de clorofila e carotenoides, amostras de 0,2 g de tecido foliar fresco foram preparadas e os extratos filtrados, sendo efetuadas leituras em espectrofotômetro (663 e 645 nm para clorofilas a e b, respectivamente). A aplicação de glyphosate e sulfumeturon-methyl nas maiores doses interferiu no conteúdo de carotenoides quando estes foram comparados com a testemunha. A maior dose de glyphosate diminuiu significativamente o conteúdo de clorofilas e carotenoides na cana-de-açúcar, porém esse resultado não se manteve quando a dose foi reduzida para 200 mL p.c. ha-1 . Os teores de clorofila foram inversamente proporcionais aos níveis Fe. A aplicação de sulfumeturon-methyl não interferiu nos teores de clorofila, no entanto os níveis de carotenoides se mostraram mais sensíveis e seus teores reduzidos. As alterações observadas nos níveis de clorofilas e carotenoides pela aplicação dos produtos podem afetar de maneira distinta o metabolismo da fotossíntese pela absorção e/ou conversão de energia.

Efeitos do glyphosate e sulfometuron-methyl no crescimento e na qualidade tecnológica da cana-de-açúcar

Os herbicidas, mesmo quando usados em doses reduzidas ou utilizados como maturadores, podem alterar a morfofisiologia da planta, o que pode levar a modificações qualitativas e quantitativas na produção. O presente estudo objetivou avaliar a eficiência agronômica e os efeitos, durante o crescimento da cana-soca, da aplicação de glyphosate e sulfometuron-methyl em baixas doses. O delineamento experimental utilizado foi o de blocos casualizados, com quatro repetições. Os tratamentos foram constituídos pelos herbicidas sulfometuron-methyl e glyphosate em diferentes doses e misturas e por uma testemunha (sem aplicação dos produtos). Uma linha de plantas de cana-de-açúcar foi destinada à aferição da qualidade tecnológica, sendo estabelecido 1 m aleatório a cada época de amostragem. Os colmos coletados foram submetidos ao desponte na altura da gema apical e à desfolha; em seguida, foram encaminhados para processamento segundo a metodologia do Sistema de Pagamento de Cana pelo Teor de Sacarose (SPCTS), sendo considerados os parâmetros tecnológicos: pol cana (PCC), pureza do caldo (PUI), açúcar total recuperável (ATR) e Brix. Nas soqueiras de cana-de-açúcar, realizaram-se análises de crescimento (altura e perfilhos). As avaliações foram realizadas na pré-colheita (30 dias após aplicação dos maturadores) e 30, 60, 90, 120, 150 e 180 dias após a colheita. Os herbicidas glyphosate e sulfometuron-methyl propiciaram melhoria da qualidade tecnológica da matéria-prima,com incrementos significativos na pureza do caldo e no Brix. A aplicação dos produtos não interferiu na produtividade e no teor de açúcar. Houve efeito estimulante no perfilhamento quando se usou glyphosate na dose de 400 mL ha-1 e redução em crescimento (altura) no início do desenvolvimento da cana, porém, com o tempo, o efeito não se manteve.

Avaliação da molhabilidade de soluções de tensoativos em aço inoxidável

With the increasing industrialization of the planet caused by globalization, it has become increasingly common to search for highly resistant and durable materials for many diverse branches of activities. Thus, production and demand for materials that meet these requirements have constantly increased with time. In view of this, stainless steel is presented as one of the materials which are suitable applications, due to many features that are interesting for several segments of the industry. Concerns of oil companies over heavy oil reservoirs have grown steadily for the last decades. Rheological properties of these oils impair their transport in conventional flow systems. This problem has created the need to develop technologies to improve flow and transport, reducing operation costs so as to enable oil production in the reservoir. Therefore, surfactant-based chemical systems are proposed to optimize transport conditions, effected by reduction of interfacial tensions, thereby enhancing the flow of oil in ducts and reducing load losses by friction. In order to examine such interactions, a study on the wettability of metallic surfaces has been undertaken, represented by measuring of contact angle of surfactant solutions onto flat plates of 304 stainless steel. Aqueous solutions of KCl, surfactants and mixtures of surfactants, with linear and aromatic hydrocarbon chain and ethoxylation degrees ranging between 20 to 100, have been tested. The wettability was assessed by means of a DSA 100 krüss goniometer. The influence of roughness on the wettability was also investigated by machining and polished the stainless steel plates with sandpapers of references ranging between 100 of 1200. The results showed that sanding and polishing plates result in decrease of wettability. As for the solutions, they have provided better wettability of the stainless steel than the KCl solutions tested. It was also been concluded that surfactant mixtures is an option to be considered, since they promote interactions that generate satisfactory contact angles for a good wettability on the stainless steel plate. Another conclusion refers to the influence of the ethoxylation degree of the nonionic surfactant molecules on wettability. It has been observed that contact angles decrease with decreasing ethoxylation degrees. This leads us to conclude that molecules with higher ethoxylation degree, being more hydrophobic, decrease the interaction of water with the ducts, thereby reducing friction and improving the flow

Reciclagem de material asfáltico fresado utilizando solventes e microemulsões

With the increase of asphalt milling services was also a significant increase in recycling services pavements. The techniques used today are basically physical processes in which the milled material is incorporated into new asphalt mixtures or executed on site, with the addition of virgin asphalt and rejuvenating agent. In this paper seeks to analyze the efficiency of extraction of CAP (Petroleum Asphalt Cement) mixtures from asphalt milling, using commercial solvents and microemulsions. The solvents were evaluated for their ability to solubilize asphalt using an extractor reflux-type apparatus. Pseudoternary diagrams were developed for the preparation of microemulsion O/W surfactant using a low-cost coconut oil saponified (OCS). Microemulsions were used to extract the CAP of asphalt through physicochemical process cold. Analysis was performed concentration of CAP in solution by spectroscopy. The data provided in the analysis of concentration by the absorbance of the solution as the basis for calculating the percentage of extraction and the mass flow of the CAP in the solution. The results showed that microemulsions prepared with low concentration of kerosene and butanol/OCS binary has high extraction power of CAP and its efficiency was higher than pure kerosene, reaching 95% rate of extraction

Caracterização físico-química, reológica e sensorial de iogurte obtido pela mistura dos leites bubalino e caprino

Milk from different animals can be used for dairy production. Yoghurt is a popular fermented milk product and considered to be one of the greatest importance in terms of consumer acceptance and consumption. The present research deals with the production of strawberry set-type yoghurt by mixing goat and buffalo s milk and it has the objective of taking advantage of the intrinsic characteristics of each milk to produce a final product with desirable attributes. It was conducted by analyzing five experimental groups with different proportions of goat and buffalo s milk: C 100% goat s milk; 7C3B - 70% goat s milk and 30% buffalo s milk, 5C5B - 50% goat s milk and 50% buffalo s milk, 3C7B 30% goat s milk and 70% buffalo s milk; B - 100% buffalo s milk. Each group was evaluated for total solids content and the acidification profile was monitored every 30 minutes by pH analysis. The yoghurt samples were analyzed for physical-chemical (pH, acidity, protein, fat, total and reducing sugars, ash and total solids), rheological (syneresis and viscosity) and sensory characteristics (appearance, odor, consistency and flavour). Samples with higher percentual of bubaline milk reached Vm faster, but the time necessary for pH 4.6 (Te) were similar between groups. Statistical differences (p<0.05) were observed for fat and total solids content of yoghurt, with superior values for groups higher proportions of buffalo s milk. The parameters of behavior reached by the model of Ostwald of Waale pointed yoghurt samples as non-Newtonian and pseudoplastic fluids. Yoghurt made only with goat s milk (C) had higher values (p<0.05) for syneresis, which can be explained by its fragile coagulum. Additionally, this group also had the lowest sensory scores for the attributes consistence and taste, while bubaline yoghurt (B) obtained the best acceptance indexes for all of the appraised parameters

Análise técnica e econômica do processo de obtenção de espaguetes com adição de farinha de trigo integral e farinha de linhaça

This work studies the fabrication of spaghetti through the process at high temperatures through the use of flour added to flour and flaxseed meal, with the aim of evaluating the final product quality and estimate the cost of production. The values of moisture, ash, protein, wet gluten, gluten index, falling number and grain of flour and mixtures to test to be the possible use in mass manufacturing and technological criteria for compliance with current legislation. Spaghetti noodles type were manufactured by adding 10% and 20% flour and 10% and 20% flaxseed meal with performance of physical-chemical, sensory and rheological properties of the products. Further analysis was performed on the product acceptance and estimation of production cost in order to create subsidies to enable the introduction of products with greater acceptance and economic viability in the market by the food industry. On the rheology of the product test was cooking the pasta, specifying the volume increase, cooking time and percentage of solid waste. In the sensory evaluation was carried out the triangular test of product differentiation with 50 trained judges and acceptance testing by a hedonic scale with evaluation of the aspects color, taste, smell and texture. In defining the sensory profile of the product was performed with ADQ 9 judges recruited and trained at the factory, using unstructured scale of 9 cm, assessing the attributes of flavor of wheat, flax flavor, consistency, texture of raw pasta, raw pasta color and color of cooked pasta. The greater acceptance of product quality was good and the pasta with 20% flour, 10% followed by the full product, 10% and 20% flaxseed characterized the average quality of the criterion of loss analysis of solids, together with mass full commercial testing. In assessing the estimated cost of production, the two products more technologically feasible and acceptable (20% whole and 10% flaxseed) were evaluated in high temperature processes. With total cost of R $ 4,872.5 / 1,000 kg and R $ 5,354.9 / 1,000 kg respectively, the difference was related to the addition of lower inputs and higher added value in the market, flour and flaxseed meal. The comparative analysis of cases was confirmed the reduction in production time (10h), more uniform product to the drying process at high temperature compared to conventional