Gas tungsten arc welding of NiTi shape memory alloy

Shape memory alloys are characterized by the ability of recovering their initial shape after being deformed and by superelasticity. Since the discovery of these alloys, a new field of interest emerged not only for the scientific community but also to many industries. However, these alloys present poor machinability which constitute a constrain in the design of complex components for new applications. Thus, the demand for joining techniques able to join these alloys without compromising their properties became of great importance to enlarge the complexity of existing applications. Literature shows that these alloys are joined mainly using laser welding. In the present study, similar NiTi butt joints, were produced using TIG welding. The welds were performed in 1.5 mm thick plates across the rolling direction. A special fixture and gas assist device was designed and manufactured. Also a robot arm was adapted to accommodate the welding torch to assure the repeatability of the welding parameters. Welds were successfully achieved without macroscopic defects, such as pores and distortions. Very superficial oxidation was seen on the top surface due to insufficient shielding gas flow on the weld face. The welded joints were mechanically tested and structurally characterized. Testing methods were used to evaluate macro and microstructure, as well as the phase transformation temperatures, the mechanical single and cyclic behaviour and the shape recovery ability. Differential Scanning Calorimetry (DSC), Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS), microhardness measurements were techniques also used to evaluate the welded joints. A depletion in Ni in the fusion zone was seen, as well as a shift in Ms temperature. For strain values of 4% the accumulated irrecoverable strain was of about 30% and increased with the strain imposed during cycling. Nevertheless, a complete recovery of initial shape was observed when testing the shape memory effect on a dedicated device that introduces a deformation of 6.7%. That is, the welding procedure does not remove the ability of the specimens to recover their initial shape.

The global shopper & brands communication at airports

This project aims to illuminate two perspectives on travel retail. On the one hand, it describes the main character of the shopping scenario at airports, namely the Global Shopper. It covers the entire profile of the referred character, the main nationalities that represent him and the current shopping trends of the passenger. Also estimates of the booming nationalities and the future purchasing trends are accurately presented. On the other hand, the travel retail market is analyzed from the airport brands’ perspective. It is described what is currently done in terms of brands communication in the top ten airports around the world and the expected future market retail trends. To accurately explore the Global Shopper behavior and purchasing preferences, a market research was conducted with a sample of 128 respondents, male and female, from different nationalities, age groups, occupation and education backgrounds. The essay tests hypothesis regarding the relevance of several variables in the purchasing process of the Global Shopper in order to understand the most pleasant way to approach consumers in travel retail. The main variables studied concern the reasons to shop at airports, to whom the passenger shops, the preferred category and brand of purchase, feelings while shopping abroad, impulsive buying behavior, brand loyalty, the use of mobile devices in the shopping process, brands communication at airports, pre-ordering online and the attitude towards self-service stores. Some findings were in accordance with expectations, while others were a surprise and may produce valuable recommendations for future travel retail practices. 4 The main relevant results concern two areas, namely pre-ordering online and self-service stores. Results showed a certain stress about not having enough time to choose between the various offerings in travel retail, as well as difficulty in dealing with crowed stores. However, pre-ordering online was not common, which would be an initiative that could solve the discomfort at airport’s stores. Moreover, self-service would promote efficiency in stores allowing passengers to save time if they already know how to go through the shopping process by themselves. Another possible recommendation concerns differentiating the strategy in travel retail for the two genders. Some differences were found in the categories bought by male and female, as well as to how brands should shape their approach concerning the demands of each gender.

Should my company use Bitcoin?

This work project analyses the possibility for a company to trade their goods and services for bitcoins, by joining the Bitcoin network. It analyses the technological and business requirements to join the Bitcoin Network by looking at Bitcoin’s potential to act as a mean of exchange for trade, unit of account and store of value. The analysis points to the motives, benefits and risks for investors to use the Bitcoin as a traditional currency and recommends on strategies for addressing those risks and maximizing benefits. Other than companies this report, to a lesser extent, will also analyse the Bitcoin from an investor’s point of view, this is, should an investor buy bitcoins for trade and make savings on a regular and everyday basis? A major finding in this work project is that companies could start using the Bitcoin system as a legit form of payment since the benefits of using this technology outweigh the costs and risks, given the right approach. This form of payment will contribute for the upgrade of a company’s business’ image, attract a new pool of consumers and businesses that already trade in bitcoins and pressure existing financial institutions and electronic payment vendors to upgrade their service levels.

Development of biomimetic microengineered hydrogel fibers for tendon regeneration

Musculoskeletal diseases are one of the leading causes of disability worldwide. Tendon injuries are responsible for substantial morbidity, pain and disability. Tissue engineering strategies aim at translating tendon structure into biomimetic materials. The main goal of the present study is to develop microengineered hydrogel fibers through the combination of microfabrication and chemical interactions between oppositely charged polyelectrolytes. For this, methacrylated hyaluronic acid (MeHA) and chondroitin sulfate (MeCS) were combined with chitosan (CHT). Hydrogel fibers were obtained by injecting polymer solutions (either MeHA or MeHA/MeCS and CHT) in separate microchannels that join at a y-junction, with the materials interacting upon contact at the interface. To evaluate cell behavior, human tendon derived cells (hTDCs) were isolated from tendon surplus samples during orthopedic surgeries and seeded on top of the fibers. hTDCs adhered to the surface of the fibers, remaining viable, and were found to be expressing CD44, the receptor for hyaluronic acid. The synthesis of hydrogel fibers crosslinkable through both physical and chemical mechanisms combined with microfabrication technology allows the development of biomimetic structures with parallel fibers being formed towards the replication of tendon tissue architecture.

Decision methods applied to solve a safety problem on a waste treatment facility

To solve a health and safety problem on a waste treatment facility, different multicriteria decision methods were used, including the PROV Exponential decision method. Four alternatives and ten attributes were considered. We found a congruent solution, validated by the different methods. The AHP and the PROV Exponential decision method led us to the same options ordering, but the last method reinforced one of the options as being the best performing one, and detached the least performing option. Also, the ELECTRE I method results led to the same ordering which allowed to point the best solution with reasonable confidence. This paper demonstrates the potential of using multicriteria decision methods to support decision making on complex problems such as risk control and accidents prevention.

STAR: Speech Therapy with Augmented Reality for children with autism spectrum disorders

Graphics based systems of Augmented and Alternative Communication are widely used to promote communication in people with Autism Spectrum Disorders. This study discusses an integration of Augmented Reality in communication interventions, by relating elements of Augmented and Alternative Communication and Applied Behaviour Analysis strategies. An architecture for an Augmented Reality based interactive system to assist interventions is proposed. STAR provides an Augmented Reality tool to assist interventions performed by therapists and support for parents to join in and participate in the child’s intervention. Finally we report on the usage of the Augmented Reality tool in interventions with children with Autism Spectrum Disorders.

A perceção dos alunos sobre a Educação Física à entrada do ensino secundário: um estudo comparativo entre o ensino regular e profissional

Relatório de estágio de mestrado em Ensino de Educação Física nos Ensinos Básico e Secundário

Os esquemas-síntese na lecionação de filosofia: a sua pertinência e aplicabilidade

Relatório de estágio de mestrado em Ensino de Filosofia no Ensino Secundário

Motivação para o desporto escolar: estudo em alunas do ensino secundário, de uma escola do concelho de Guimarães

Relatório de estágio de mestrado em Ensino de Educação Física nos Ensinos Básico e Secundário

Otimização com restrições de complementaridade: algoritmos e aplicações

Tese de Doutoramento em Engenharia Industrial e de Sistemas (PDEIS)

Tailored magnetic and magnetoelectric responses of polymer-based composites

The manipulation of electric ordering with applied magnetic fields has been realized on magnetoelectric (ME) materials, however, their ME switching is often accompanied by significant hysteresis and coercivity that represents, for some applications, a severe weakness. To overcome this obstacle, this work focus on the development of a new type of ME polymer nanocomposites that exhibits tailored ME response at room temperature. The multiferroic nanocomposites are based on three different ferrite nanoparticles, Zn0.2Mn0.8Fe2O4 (ZMFO), CoFe2O4 (CFO) and Fe3O4 (FO), dispersed in a piezoelectric co-polymer poly(vinylindene fluoride-trifluoroethylene), P(VDF-TrFE), matrix. No substantial differences were detected on the time-stable piezoelectric response of the composites (≈ -28 pC.N−1) with distinct ferrite fillers and for the same ferrite content of 10wt.%. Magnetic hysteresis loops from pure ferrite nanopowders showed different magnetic responses. ME results of the nanocomposite films with 10wt.% ferrite content revealed that the ME induced voltage increases with increasing DC magnetic field until a maximum of 6.5 mV∙cm−1∙Oe−1, at an optimum magnetic field of 0.26 T, and 0.8 mV∙cm−1∙Oe−1, at an optimum magnetic field of 0.15T, for the CFO/P(VDF-TrFE) and FO/P(VDF-TrFE) composites, respectively. On the contrary, the ME response of the ZMFO/P(VDF-TrFE) exposed no hysteresis and high dependence on the ZMFO filler content. Possible innovative applications such as memories and information storage, signal processing, ME sensors and oscillators have been addressed for such ferrite/PVDF nanocomposites.

Gestão de inventários numa empresa de produção de linhas de costura

Dissertação de mestrado integrado em Engenharia e Gestão Industrial

Modelos de sistemas de financiamento dos cuidados de saúde: o impacto nos custos

Ao longo das últimas décadas tem-se verificado um crescente aumento dos custos de saúde na generalidade dos países e, em particular, nos países desenvolvidos. Este facto tem suscitado o aumento de estudos sobre os determinantes dos custos de saúde, bem como uma crescente preocupação por parte dos decisores políticos. No cerne da discussão está a importância da organização e do modelo de financiamento dos sistemas de saúde, de forma a promover a eficiência e a assegurar o acesso equitativo aos cuidados de saúde. A presente dissertação procura analisar a evolução dos custos com a saúde dos 15 países mais antigos da União Europeia, da Suíça e dos Estados Unidos da América, entre o período de 2000 e 2013. Os objetivos principais deste trabalho são os de compreender os aspetos gerais dos modelos de financiamento de saúde presentes concentrando-nos na questão das fontes de financiamento para analisar o impacto que estas têm nos custos de saúde dos países, nomeadamente no montante de custos e na sua evolução recente. Os resultados deste estudo sugerem que o crescimento do PIB se encontra associado ao aumento dos gastos de saúde, culminando com as conclusões propostas por estudos anteriores. A evidência sobre o impacto do envelhecimento das populações não é conclusiva. A forma como os sistemas de saúde dos diferentes países são organizados e financiados, também influenciam a evolução dos custos de saúde.

Identificação de fendilhamento de pavimentos e propriedades volumétricas das misturas betuminosas utilizando um Georadar

Dissertação de mestrado integrado em Engenharia Civil

Estudo numérico sobre o reforço de pilares de betão armado com cantoneiras e presilhas metálicas: análise paramétrica e modelo de cálculo

Dissertação de mestrado integrado em Engenharia Civil