Avalanche-like vortex penetration driven by pulsed microwave fields in an epitaxial LaSrCuO thin film

Different vortex penetration regimes have been registered in the output voltage signal of a magnetometer when single microwave pulses are applied to an epitaxial overdoped La2− x Sr x CuO4 thin film in a perpendicular dc magnetic field. The onset of a significant variation in the sample magnetization which exists below threshold values of temperature, dc magnetic field, and pulse duration is interpreted as an avalanche-type flux penetration. The microwave contribution to the background electric field suggests that the nucleation of this fast vortex motion is of electric origin, which also guarantees the occurrence of vortex instabilities under adiabatic conditions via the enhancement of the flux flow resistivity. Flux creep phenomena and heat transfer effects act as stabilizing factors against the microwave-pulse-induced fast flux diffusion.

Intermittent atrial tachycardia facilitates atrial fibrillation by a shortening of activation recovery interval

Introduction: We recently observed in a chronic ovine model that a shortening of action potential duration (APD) as assessed by the activation recovery interval (ARI) may be a mechanism whereby pacing-induced atrial tachycardia (PIAT) facilitates atrial fibrillation (AF), mediated by a return to 1:1 atrial capture after the effective refractory period has been reached. The aim of the present study is to evaluate the effect of long term intermittent burst pacing on ARI before induction of AF.Methods: We specifically developed a chronic ovine model of PIAT using two pacemakers (PM) each with a right atrial (RA) lead separated by ∼2cm. The 1st PM (Vitatron T70) was used to record a broadband unipolar RA EGM (800 Hz, 0.4 Hz high pass filter). The 2nd was used to deliver PIAT during electrophysiological protocols at decremental pacing CL (400 beats, from 400 to 110ms) and long term intermittent RA burst pacing to promote electrical remodeling (5s of burst followed by 2s of sinus rhythm) until onset of sustained AF. ARI was defined as the time difference between the peak of the atrial repolarization wave and the first atrial depolarization. The mean ARIs of paired sequences (before and after remodeling), each consisting of 20 beats were compared.Results: As shown in the figure, ARIs (n=4 sheep, 46 recordings) decreased post remodeling compared to baseline (86±19 vs 103±12 ms, p<0.05). There was no difference in atrial structure as assessed by light microscopy between control and remodeled sheep.Conclusions: Using standard pacemaker technology, atrial ARIs as a surrogate of APDs were successfully measured in vivo during the electrical remodeling process leading to AF. The facilitation of AF by PIAT mimicking salvos from pulmonary veins is heralded by a significant shortening of ARI.

Reduced microwave losses of YBa2Cu3O7_thin films on electro-optic LiNbO3 crystals

We report on the growth of epitaxial YBa2Cu3O7 thin films on X-cut LiNbO3 single crystals. The use of double CeO2/YSZ buffer layers allows a single in-plane orientation of YBa2Cu3O7, and results in superior superconducting properties. In particular, surface resistance Rs values of 1.4 m¿ have been measured at 8 GHz and 65 K. The attainment of such low values of Rs constitutes a key step toward the incorporation of high Tc materials as electrodes in photonic and acoustic devices.

Microwave spectrometry for the Evaluation of the structural integrity of metallic stents

Purpose: To assess the feasibility of a method based on microwave spectrometry to detect structural distortions of metallic stents in open air conditions and envisage the prospects of this approach toward possible medical applicability for the evaluation of implanted stents. Methods: Microwave absorbance spectra between 2.0 and 18.0 GHz were acquired in open air for the characterization of a set of commercial stents using a specifically design setup. Rotating each sample over 360º, 2D absorbance diagrams were generated as a function of frequency and rotation angle. To check our approach for detecting changes in stent length (fracture) and diameter (recoil), two specific tests were performed in open air. Finally, with a few adjustments, this same system provides 2D absorbance diagrams of stents immersed in a water-based phantom, this time over a bandwidth ranging from 0.2 to 1.8 GHz. Results: The authors show that metallic stents exhibit characteristic resonant frequencies in their microwave absorbance spectra in open air which depend on their length and, as a result, may reflect the occurrence of structural distortions. These resonances can be understood considering that such devices behave like dipole antennas in terms of microwave scattering. From fracture tests, the authors infer that microwave spectrometry provides signs of presence of Type I to Type IV stent fractures and allows in particular a quantitative evaluation of Type III and Type IV fractures. Recoil tests show that microwave spectrometry seems able to provide some quantitative assessment of diametrical shrinkage, but only if it involves longitudinal shortening. Finally, the authors observe that the resonant frequencies of stents placed inside the phantom shift down with respect to the corresponding open air frequencies, as it should be expected considering the increase of dielectric permittivity from air to water. Conclusions: The evaluation of stent resonant frequencies provided by microwave spectrometry allows detection and some quantitative assessment of stent fracture and recoil in open air conditions. Resonances of stents immersed in water can be also detected and their characteristic frequencies are in good agreement with theoretical estimates. Although these are promising results, further verifica tion in a more relevant phantom is required in order to foresee the real potential of this approach.

Molecular and morphological characterization of hydrochar produced by microwave-assisted hydrothermal carbonization of cellulose

The objective of this work was to characterize the morphology and molecular composition of the hydrochar produced by microwave-assisted hydrothermal carbonization of cellulose. The produced hydrochar consists mainly of aggregate microspheres with about 2.0 µm in diameter, with aliphatic and aromatic structures and the presence of carbonyl functional groups. The aromatic groups are formed mainly by benzofuran-like structures, being chemically different from common cellulose char. Microwave-assisted hydrothermal carbonization yields a functionalized carbon-rich material similar to that produced by the conventional hydrothermal process.

Forage production of elephant grass under intermittent stocking

The objective of this work was to evaluate the dry matter production of elephant grass (Pennisetum purpureum) genotypes, managed under intermittent stocking. A completely randomized design was used, with two genotypes and three replicates. The treatments consisted of factorial combinations (2x2x2) of genotypes ('BRS Kurumi' and the clone CNPGL 00‑1‑3), two light interception levels (LI) at the onset of grazing (90 and 95%), and two post‑grazing canopy heights (30 and 50 cm). A total of 24 Holstein x Zebu crossbred heifers were used. The stocking density varied in order to finish the grazing periods in two days. The interval between the defoliation, based on 95% LI, resulted in a higher leaf mass per grazing cycle. The post‑grazing height of 30 cm did not affect the number of grazing cycles but provided a greater herbage accumulation rate. The cultivar BRS Kurumi has higher pasture growth, lower rest period, and greater number of grazing cycles, which results in increased forage production in the growing season.

Electromyographic, cerebral, and muscle hemodynamic responses during intermittent, isometric contractions of the biceps brachii at three submaximal intensities.

This study examined the electromyographic, cerebral and muscle hemodynamic responses during intermittent isometric contractions of biceps brachii at 20, 40, and 60% of maximal voluntary contraction (MVC). Eleven volunteers completed 2 min of intermittent isometric contractions (12/min) at an elbow angle of 90° interspersed with 3 min rest between intensities in systematic order. Surface electromyography (EMG) was recorded from the right biceps brachii and near infrared spectroscopy (NIRS) was used to simultaneously measure left prefrontal and right biceps brachii oxyhemoglobin (HbO2), deoxyhemoglobin (HHb), and total hemoglobin (Hbtot). Transcranial Doppler ultrasound was used to measure middle cerebral artery velocity (MCAv) bilaterally. Finger photoplethysmography was used to record beat-to-beat blood pressure and heart rate. EMG increased with force output from 20 to 60% MVC (P < 0.05). Cerebral HbO2 and Hbtot increased while HHb decreased during contractions with differences observed between 60% vs. 40% and 20% MVC (P < 0.05). Muscle HbO2 decreased while HHb increased during contractions with differences being observed among intensities (P < 0.05). Muscle Hbtot increased from rest at 20% MVC (P < 0.05), while no further change was observed at 40 and 60% MVC (P > 0.05). MCAv increased from rest to exercise but was not different among intensities (P > 0.05). Force output correlated with the root mean square EMG and changes in muscle HbO2 (P < 0.05), but not changes in cerebral HbO2 (P > 0.05) at all three intensities. Force output declined by 8% from the 1st to the 24th contraction only at 60% MVC and was accompanied by systematic increases in RMS, cerebral HbO2 and Hbtot with a leveling off in muscle HbO2 and Hbtot. These changes were independent of alterations in mean arterial pressure. Since cerebral blood flow and oxygenation were elevated at 60% MVC, we attribute the development of fatigue to reduced muscle oxygen availability rather than impaired central neuronal activation.

A model of the wind direction signature in the Stokes emission vector from the ocean surface at microwave frequencies

This paper presents a model of the Stokes emission vector from the ocean surface. The ocean surface is described as an ensemble of facets with Cox and Munk's (1954) Gram-Charlier slope distribution. The study discusses the impact of different up-wind and cross-wind rms slopes, skewness, peakedness, foam cover models and atmospheric effects on the azimuthal variation of the Stokes vector, as well as the limitations of the model. Simulation results compare favorably, both in mean value and azimuthal dependence, with SSM/I data at 53° incidence angle and with JPL's WINDRAD measurements at incidence angles from 30° to 65°, and at wind speeds from 2.5 to 11 m/s.

General electromagnetic simulation tool to predict the microwave nonlinear response of planar, arbitrarily-shaped HTS structures

This work describes a simulation tool being developed at UPC to predict the microwave nonlinear behavior of planar superconducting structures with very few restrictions on the geometry of the planar layout. The software is intended to be applicable to most structures used in planar HTS circuits, including line, patch, and quasi-lumped microstrip resonators. The tool combines Method of Moments (MoM) algorithms for general electromagnetic simulation with Harmonic Balance algorithms to take into account the nonlinearities in the HTS material. The Method of Moments code is based on discretization of the Electric Field Integral Equation in Rao, Wilton and Glisson Basis Functions. The multilayer dyadic Green's function is used with Sommerfeld integral formulation. The Harmonic Balance algorithm has been adapted to this application where the nonlinearity is distributed and where compatibility with the MoM algorithm is required. Tests of the algorithm in TM010 disk resonators agree with closed-form equations for both the fundamental and third-order intermodulation currents. Simulations of hairpin resonators show good qualitative agreement with previously published results, but it is found that a finer meshing would be necessary to get correct quantitative results. Possible improvements are suggested.

Graphitized carbon black in quartz tubes for the sampling of indoor air nicotine and analysis by microwave thermal desorption-capillary gas chromatography

Nicotine in a smoky indoor air environment can be determined using graphitized carbon black as a solid sorbent in quartz tubes. The temperature stability, high purity, and heat absorption characteristics of the sorbent, as well as the permeability of the quartz tubes to microwaves, enable the thermal desorption by means of microwaves after active sampling. Permeation and dynamic dilution procedures for the generation of nicotine in the vapor phase at low and high concentrations are used to evaluate the performances of the sampler. Tube preparation is described and the microwave desorption temperature is measured. Breakthrough volume is determined to allow sampling at 0.1-1 L/min for definite periods of time. The procedure is tested for the determination of gas and paticulate phase nicotine in sidestream smoke produced in an experimental chamber.

Cardiorespiratory and Cardiac Autonomic Responses to 30-15 Intermittent Fitness Test in Team Sport Players

Buchheit, M, Al Haddad, H, Millet GP, Lepretre, PM, Newton, M, and Ahmaidi, S. Cardiorespiratory and cardiac autonomic responses to 30-15 Intermittent Fitness Test in team sport players. J Strength Cond Res 23(1): xxx-xxx, 2009-The 30-15 Intermittent Fitness Test (30-15IFT) is an attractive alternative to classic continuous incremental field tests for defining a reference velocity for interval training prescription in team sport athletes. The aim of the present study was to compare cardiorespiratory and autonomic responses to 30-15IFT with those observed during a standard continuous test (CT). In 20 team sport players (20.9 +/- 2.2 years), cardiopulmonary parameters were measured during exercise and for 10 minutes after both tests. Final running velocity, peak lactate ([La]peak), and rating of perceived exertion (RPE) were also measured. Parasympathetic function was assessed during the postexercise recovery phase via heart rate (HR) recovery time constant (HRRtau) and HR variability (HRV) vagal-related indices. At exhaustion, no difference was observed in peak oxygen uptake (&OV0312;o2peak), respiratory exchange ratio, HR, or RPE between 30-15IFT and CT. In contrast, 30-15IFT led to significantly higher minute ventilation, [La]peak, and final velocity than CT (p < 0.05 for all parameters). All maximal cardiorespiratory variables observed during both tests were moderately to well correlated (e.g., r = 0.76, p = 0.001 for &OV0312;o2peak). Regarding ventilatory thresholds (VThs), all cardiorespiratory measurements were similar and well correlated between the 2 tests. Parasympathetic function was lower after 30-15IFT than after CT, as indicated by significantly longer HHRtau (81.9 +/- 18.2 vs. 60.5 +/- 19.5 for 30-15IFT and CT, respectively, p < 0.001) and lower HRV vagal-related indices (i.e., the root mean square of successive R-R intervals differences [rMSSD]: 4.1 +/- 2.4 and 7.0 +/- 4.9 milliseconds, p < 0.05). In conclusion, the 30-15IFT is accurate for assessing VThs and &OV0312;o2peak, but it alters postexercise parasympathetic function more than a continuous incremental protocol.

Syttyminen ja palamisen eteneminen partikkelikerroksessa

Syttymistä ja palamisen etenemistä partikkelikerroksessa tutkitaan paloturvallisuuden parantamista sekä kiinteitä polttoaineita käyttävien polttolaitteiden toiminnan tuntemista ja kehittämistä varten. Tässä tutkimuksessa on tavoitteena kerätä yhteen syttymiseen ja liekkirintaman etenemiseen liittyviä kokeellisia ja teoreettisia tutkimustuloksia, jotka auttavat kiinteäkerrospoltto- ja -kaasutus-laitteiden kehittämisessä ja suunnittelussa. Työ on esitutkimus sitä seuraavalle kokeelliselle ja teoreettiselle osalle. Käsittelyssä keskitytään erityisesti puuperäisiin polttoaineisiin. Hiilidioksidipäästöjen vähentämistavoitteet sekä kiinteiden jätteiden energiakäytön lisääminen ja kaatopaikalle viennin vähentäminen aiheuttavat lähitulevaisuudessa kerrospolton lisääntymistä. Kuljetusmatkojen optimoinnin takia joudutaan rakentamaan melko pieniä polttolaitoksia, joissa kerrospolttotekniikka on edullisin vaihtoehto. Syttymispisteellä tarkoitetaan Semenovin määritelmän mukaan tilaa ja ajankohtaa, jolloin polttoaineen ja hapen reaktioissa muodostuva nettoenergia aikayksikössä on yhtäsuuri kuin ympäristöön siirtyvä nettoenergiavirta. Itsesyttyminen tarkoittaa syttymistä ympäristön lämpötilan tai paineen suurenemisen seurauksena. Pakotettu syttyminen tapahtuu, kun syttymispisteen läheisyydessä on esimerkiksi liekki tai hehkuva kiinteä kappale, joka aiheuttaa paikallisen syttymisen ja syttymisrintaman leviämisen muualle polttoaineeseen. Kokeellinen tutkimus on osoittanut tärkeimmiksi syttymiseen ja syttymisrintaman etenemiseen vaikuttaviksi tekijöiksi polttoaineen kosteuden, haihtuvien aineiden pitoisuuden ja lämpöarvon, partikkelikerroksen huokoisuuden, partikkelien koon ja muodon, polttoaineen pinnalle tulevan säteilylämpövirran tiheyden, kaasun virtausnopeuden kerroksessa, hapen osuuden ympäristössä sekä palamisilman esilämmityksen. Kosteuden lisääntyminen suurentaa syttymisenergiaa ja -lämpötilaa sekä pidentää syttymisaikaa. Mitä enemmän polttoaine sisältää haihtuvia aineita sitä pienemmässä lämpötilassa se syttyy. Syttyminen ja syttymisrintaman eteneminen ovat sitä nopeampia mitä suurempi on polttoaineen lämpöarvo. Kerroksen huokoisuuden kasvun on havaittu suurentavan palamisen etenemisnopeutta. Pienet partikkelit syttyvät yleensä nopeammin ja pienemmässä lämpötilassa kuin suuret. Syttymisrintaman eteneminen nopeutuu partikkelien pinta-ala - tilavuussuhteen kasvaessa. Säteilylämpövirran tiheys on useissa polttosovellutuksissa merkittävin lämmönsiirtotekijä, jonka kasvu luonnollisesti nopeuttaa syttymistä. Ilman ja palamiskaasujen virtausnopeus kerroksessa vaikuttaa konvektiiviseen lämmönsiirtoon ja hapen pitoisuuteen syttymisvyöhykkeellä. Ilmavirtaus voi jäähdyttää ja kuumankaasun virtaus lämmittää kerrosta. Hapen osuuden kasvaminen nopeuttaa syttymistä ja liekkirintaman etenemistä kunnes saavutetaan tila, jota suuremmilla virtauksilla ilma jäähdyttää ja laimentaa reaktiovyöhykettä. Palamisilman esilämmitys nopeuttaa syttymisrintaman etenemistä. Syttymistä ja liekkirintaman etenemistä kuvataan yleensä empiirisillä tai säilyvyysyhtälöihin perustuvilla malleilla. Empiiriset mallit perustuvat mittaustuloksista tehtyihin korrelaatioihin sekä joihinkin tunnettuihin fysikaalisiin lainalaisuuksiin. Säilyvyysyhtälöihin perustuvissa malleissa systeemille määritetään massan, energian, liikemäärän ja alkuaineiden säilymisyhtälöt, joiden nopeutta kuvaavien siirtoyhtälöiden muodostamiseen käytetään teoreettisella ja kokeellisella tutkimuksella saatuja yhtälöitä. Nämä mallinnusluokat ovat osittain päällekkäisiä. Pintojen syttymistä kuvataan usein säilyvyysyhtälöihin perustuvilla malleilla. Partikkelikerrosten mallinnuksessa tukeudutaan enimmäkseen empiirisiin yhtälöihin. Partikkelikerroksia kuvaavista malleista Xien ja Liangin hiilipartikkelikerroksen syttymiseen liittyvä tutkimus ja Gortin puun ja jätteen polttoon liittyvä reaktiorintaman etenemistutkimus ovat lähimpänä säilyvyysyhtälöihin perustuvaa mallintamista. Kaikissa malleissa joudutaan kuitenkin yksinkertaistamaan todellista tapausta esimerkiksi vähentämällä dimensioita, reaktioita ja yhdisteitä sekä eliminoimalla vähemmän merkittävät siirtomekanismit. Suoraan kerrospolttoa ja -kaasutusta palvelevia syttymisen ja palamisen etenemisen tutkimuksia on vähän. Muita tarkoituksia varten tehtyjen tutkimusten polttoaineet, kerrokset ja ympäristöolosuhteet poikkeavat yleensä selvästi polttolaitteiden vastaavista olosuhteista. Erikokoisten polttoainepartikkelien ja ominaisuuksiltaan erilaisten polttoaineiden seospolttoa ei ole tutkittu juuri ollenkaan. Polttoainepartikkelien muodon vaikutuksesta on vain vähän tutkimusta.Ilman kanavoitumisen vaikutuksista ei löytynyt tutkimuksia.

Tuning the design procedures for laser processed microwave mechanics

This research has been focused at the development of a tuned systematic design methodology, which gives the best performance in a computer aided environment and utilises a cross-technological approach, specially tested with and for laser processed microwave mechanics. A tuned design process scheme is also presented. Because of the currently large production volumes of microwave and radio frequency mechanics even slight improvements of design methodologies or manufacturing technologies would give reasonable possibilities for cost reduction. The typical number of required iteration cycles could be reduced to one fifth of normal. The research area dealing with the methodologies is divided firstly into a function-oriented, a performance-oriented or a manufacturability-oriented product design. Alternatively various approaches can be developed for a customer-oriented, a quality-oriented, a cost-oriented or an organisation-oriented design. However, the real need for improvements is between these two extremes. This means that the effective methodology for the designers should not be too limited (like in the performance-oriented design) or too general (like in the organisation-oriented design), but it should, include the context of the design environment. This is the area where the current research is focused. To test the developed tuned design methodology for laser processing (TDMLP) and the tuned optimising algorithm for laser processing (TOLP), seven different industrial product applications for microwave mechanics have been designed, CAD-modelled and manufactured by using laser in small production series. To verify that the performance of these products meets the required level and to ensure the objectiveness ofthe results extensive laboratory tests were used for all designed prototypes. As an example a Ku-band horn antenna can be laser processed from steel in 2 minutes at the same time obtaining a comparable electrical performance of classical aluminium units or the residual resistance of a laser joint in steel could be limited to 72 milliohmia.

Ash Particle Erosion on Steam Boiler Convective Section

In this study, equations for the calculation of erosion wear caused by ash particles on convective heat exchanger tubes of steam boilers are presented. Anew, three-dimensional test arrangement was used in the testing of the erosion wear of convective heat exchanger tubes of steam boilers. When using the sleeve-method, three different tube materials and three tube constructions could be tested. New results were obtained from the analyses. The main mechanisms of erosionwear phenomena and erosion wear as a function of collision conditions and material properties have been studied. Properties of fossil fuels have also been presented. When burning solid fuels, such as pulverized coal and peat in steam boilers, most of the ash is entrained by the flue gas in the furnace. In bubbling andcirculating fluidized bed boilers, particle concentration in the flue gas is high because of bed material entrained in the flue gas. Hard particles, such as sharp edged quartz crystals, cause erosion wear when colliding on convective heat exchanger tubes and on the rear wall of the steam boiler. The most important ways to reduce erosion wear in steam boilers is to keep the velocity of the flue gas moderate and prevent channelling of the ash flow in a certain part of the cross section of the flue gas channel, especially near the back wall. One can do this by constructing the boiler with the following components. Screen plates can beused to make the velocity and ash flow distributions more even at the cross-section of the channel. Shield plates and plate type constructions in superheaters can also be used. Erosion testing was conducted with three types of tube constructions: a one tube row, an inline tube bank with six tube rows, and a staggered tube bank with six tube rows. Three flow velocities and two particle concentrations were used in the tests, which were carried out at room temperature. Three particle materials were used: quartz, coal ash and peat ash particles. Mass loss, diameter loss and wall thickness loss measurements of the test sleeves were taken. Erosion wear as a function of flow conditions, tube material and tube construction was analyzed by single-variable linear regression analysis. In developing the erosion wear calculation equations, multi-variable linear regression analysis was used. In the staggered tube bank, erosion wear had a maximum value in a tube row 2 and a local maximum in row 5. In rows 3, 4 and 6, the erosion rate was low. On the other hand, in the in-line tube bank the minimum erosion rate occurred in tube row 2 and in further rows the erosion had an increasing value, so that in a six row tube bank, the maximum value occurred in row 6.