On the efficiency of impingers with fritted nozzle tip for collection of ultrafine particles

The aim of this study was to determine the collection efficiency of ultrafine particles into an impinger fitted with a fritted nozzle tip as a means to increase contact surface area between the aerosol and the liquid. The influence of liquid sampling volume, frit porosity and the nature of the sampling liquid was explored and it was shown that all impact on the collection efficiency of particles smaller than 220 nm. Obtained values for overall collection efficiency were substantially higher (~30–95%) than have been previously reported, mainly due to the high deposition of particles in the fritted nozzle tip, especially in case of finer porosity frits and smaller particles. Values for the capture efficiency of the solvent alone ranged from 20 to 45%, depending on the type and the volume of solvent. Additionally, our results show that airstream dispersion into bubbles improves particle trapping by the liquid and that there is a difference in collection efficiencies based on the nature and volume of the solvent used.

A quasi stationary approach to drying kinetics of cylindrical food particulates in a heat pump asisted fluid bed dryer

Experiments were undertaken to study drying kinetics of moist cylindrical shaped food particulates during fluidised bed drying. Cylindrical particles were prepared from Green beans with three different length:diameter ratios, 3:1, 2:1 and 1:1. A batch fluidised bed dryer connected to a heat pump system was used for the experimentation. A Heat pump and fluid bed combination was used to increase overall energy efficiency and achieve higher drying rates. Drying kinetics, were evaluated with non-dimensional moisture at three different drying temperatures of 30, 40 and 50o C. Numerous mathematical models can be used to calculate drying kinetics ranging from analytical models with simplified assumptions to empirical models built by regression using experimental data. Empirical models are commonly used for various food materials due to their simpler approach. However problems in accuracy, limits the applications of empirical models. Some limitations of empirical models could be reduced by using semi-empirical models based on heat and mass transfer of the drying operation. One such method is the quasi-stationary approach. In this study, a modified quasi-stationary approach was used to model drying kinetics of the cylindrical food particles at three drying temperatures.

Final report : tasks 1 and 4: eco-efficiency assessment of building refurbishment

The main objective was to compare the environmental impacts of a building undergoing refurbishment both before and after the refurbishment and to assist in the design of the refurbishment with what is learned.

Re-life of buildings - decision support tools for maximising project efficiency

This paper describes the process adopted in developing an integrated decision support framework for planning of office building refurbishment projects, with specific emphasize on optimising rentable floor space, structural strengthening, residual life and sustainability. Expert opinion on the issues to be considered in a tool is being captured through the DELPHI process, which is currently ongoing. The methodology for development of the integrated tool will be validated through decisions taken during a case study project: refurbishment of CH1 building of Melbourne City Council, which will be followed through to completion by the research team. Current status of the CH1 planning will be presented in the context of the research project.

Sustainable construction for the future - the role of government in energy efficiency and sustainability in buildings

This paper will summarise the findings from a study that explored the link between dwelling design, or type, and energy efficiencies in sub-tropical climates. An increasing number of government and private sector development companies are initiating projects that aim to deliver enhanced environmental outcomes at both sub-divisional and dwelling levels. The study used AccuRate, a new thermal modelling tool developed by CSIRO that responds to the need to improve ventilation modelling. The study found that dwellings developed in conjunction with the Departments of Housing and Public Works have set the benchmark. It provides a snapshot of the energy efficiency of a range of dwelling types found in recent subdivisions. However, the trend toward increasing urban densities may reduce the likelihood that cooling breezes will be available to cool dwellings. The findings are relevant to regulators, designers and industry in all states interested in reducing the energy used to cool dwellings in summer.

Integrating eco-efficiency assessment of commercial buildings into the design process : LCADesign

The ability to assess a commercial building for its impact on the environment at the earliest stage of design is a goal which is achievable by integrating several approaches into a single procedure directly from the 3D CAD representation. Such an approach enables building design professionals to make informed decisions on the environmental impact of building and its alternatives during the design development stage instead of at the post-design stage where options become limited. The indicators of interest are those which relate to consumption of resources and energy, contributions to pollution of air, water and soil, and impacts on the health and wellbeing of people in the built environment as a result of constructing and operating buildings. 3D object-oriented CAD files contain a wealth of building information which can be interrogated for details required for analysis of the performance of a design. The quantities of all components in the building can be automatically obtained from the 3D CAD objects and their constituent materials identified to calculate a complete list of the amounts of all building products such as concrete, steel, timber, plastic etc. When this information is combined with a life cycle inventory database, key internationally recognised environmental indicators can be estimated. Such a fully integrated tool known as LCADesign has been created for automated ecoefficiency assessment of commercial buildings direct from 3D CAD. This paper outlines the key features of LCADesign and its application to environmental assessment of commercial buildings.

LCADesign : an integrated approach to automatic eco-efficiency assessment of commercial buildings

Buildings consume resources and energy, contribute to pollution of our air, water and soil, impact the health and well-being of populations and constitute an important part of the built environment in which we live. The ability to assess their design with a view to reducing that impact automatically from their 3D CAD representations enables building design professionals to make informed decisions on the environmental impact of building structures. Contemporary 3D object-oriented CAD files contain a wealth of building information. LCADesign has been designed as a fully integrated approach for automated eco-efficiency assessment of commercial buildings direct from 3D CAD. LCADesign accesses the 3D CAD detail through Industry Foundation Classes (IFCs) - the international standard file format for defining architectural and constructional CAD graphic data as 3D real-world objects - to permit construction professionals to interrogate these intelligent drawing objects for analysis of the performance of a design. The automated take-off provides quantities of all building components whose specific production processes, logistics and raw material inputs, where necessary, are identified to calculate a complete list of quantities for all products such as concrete, steel, timber, plastic etc and combines this information with the life cycle inventory database, to estimate key internationally recognised environmental indicators such as CML, EPS and Eco-indicator 99. This paper outlines the key modules of LCADesign and their role in delivering an automated eco-efficiency assessment for commercial buildings.

Conference Report of the First Meeting of the Native American and Indigenous Studies Association, 21-23 May 2009, Department of American Indian Studies, University of Minneapolis, Minesota, United States of America

Report provided back by Bronwyn Fredericks on her participation at the First Native American and Indigenous Studies Association Meeting held 21-23 May 2009 in Minnesota, United States of America.

Assessing the energy efficiency of gear oils via the FZG test machine

Energy efficient lubricants are becoming increasingly popular. This is due to a global increase in environmental awareness combined with the potential of reducing operating costs. A new test method of evaluating the energy efficiency of gear oils has been described in this report. The method involves measuring the power required by an FZG test rig to run while using a particular test lubricant. For each oil that was being evaluated, the rig was run for 10 minutes at a load stage of 10. Six extreme pressure (EP) industrial gear oils of mineral base were tested. The difference in power requirements between the best and the worst performing oils was 2.77 and 3.24 kW, respectively. This equates to a 14.6% reduction in power, a significant amount if considered in relation to a high powered industrial machine. The oils of superior performance were noticed to run at reduced temperatures. They were also more expensive than the other products of lesser performance.

An investigation into how work-related road safety can be enhanced

Despite the facts that vehicle incidents continue to be the most common mechanism for Australian compensated fatalities and that employers have statutory obligations to provide safe workplaces, very few organisations are proactively and comprehensively managing their work-related road risks. Unfortunately, limited guidance is provided in the existing literature to assist practitioners in managing work-related road risks. The current research addresses this gap in the literature. To explore how work-related road safety can be enhanced, three studies were conducted. Study one explored the effectiveness of a range of risk management initiatives and whether comprehensive risk management practices were associated with safety outcomes. Study two explored barriers to, and facilitators for, accepting risk management initiatives. Study three explored the influence of organisational factors on road safety outcomes to identify optimal work environments for managing road risks. To maximise the research sample and increase generalisability, the studies were designed to allow data collection to be conducted simultaneously drawing upon the same sample obtained from four Australian organisations. Data was collected via four methods. A structured document review of published articles was conducted to identify what outcomes have been observed in previously investigated work-related road safety initiatives. The documents reviewed collectively assessed the effectiveness of 19 work-related road safety initiatives. Audits of organisational practices and process operating within the four researched organisations were conducted to identify whether organisations with comprehensive work-related road risk management practices and processes have better safety outcomes than organisations with limited risk management practices and processes. Interviews were conducted with a sample of 24 participants, comprising 16 employees and eight managers. The interviews were conducted to identify what barriers and facilitators within organisations are involved in implementing work-related road safety initiatives and whether differences in fleet safety climate, stage of change and safety ownership relate to work-related road safety outcomes. Finally, questionnaires were administered to a sample of 679 participants. The questionnaires were conducted to identify which initiatives are perceived by employees to be effective in managing work-related road risks and whether differences in fleet safety climate, stage of change and safety ownership relate to work-related road safety outcomes. Seven research questions were addressed in the current research project. The key findings with respect to each of the research questions are presented below. Research question one: What outcomes have been observed in previously investigated work-related road safety initiatives? The structured document review indicated that initiatives found to be positively associated with occupational road safety both during and after the intervention period included: a pay rise; driver training; group discussions; enlisting employees as community road safety change agents; safety reminders; and group and individual rewards. Research question two: Which initiatives are perceived by employees to be effective in managing work-related road risks? Questionnaire findings revealed that employees believed occupational road risks could best be managed through making vehicle safety features standard, providing practical driver skills training and through investigating serious vehicle incidents. In comparison, employees believed initiatives including signing a promise card commitment to drive safely, advertising the organisation’s phone number on vehicles and consideration of driving competency in staff selection process would have limited effectiveness in managing occupational road safety. Research question three: Do organisations with comprehensive work-related road risk management practices and processes have better safety outcomes than organisations with limited risk management practices and processes? The audit identified a difference among the organisations in their management of work-related road risks. Comprehensive risk management practices were associated with employees engaging in overall safer driving behaviours, committing less driving errors, and experiencing less fatigue and distraction issues when driving. Given that only four organisations participated in this research, these findings should only be considered as preliminary. Further research should be conducted to explore the relationship between comprehensiveness of risk management practices and road safety outcomes with a larger sample of organisations. Research question four: What barriers and facilitators within organisations are involved in implementing work-related road safety initiatives? The interviews identified that employees perceived six organisational characteristics as potential barriers to implementing work-related road safety initiatives. These included: prioritisation of production over safety; complacency towards work-related road risks; insufficient resources; diversity; limited employee input in safety decisions; and a perception that road safety initiatives were an unnecessary burden. In comparison, employees perceived three organisational characteristics as potential facilitators to implementing work-related road safety initiatives. These included: management commitment; the presence of existing systems that could support the implementation of initiatives; and supportive relationships. Research question five: Do differences in fleet safety climate relate to work-related road safety outcomes? The interviews and questionnaires identified that organisational climates with high management commitment, support for managing work demands, appropriate safety rules and safety communication were associated with employees who engaged in safer driving behaviours. Regression analyses indicated that as participants’ perceptions of safety climate increased, the corresponding likelihood of them engaging in safer driving behaviours increased. Fleet safety climate was perceived to influence road safety outcomes through several avenues. Some of these included: the allocation of sufficient resources to manage occupational road risks; fostering a supportive environment of mutual responsibility; resolving safety issues openly and fairly; clearly communicating to employees that safety is the top priority; and developing appropriate work-related road safety policies and procedures. Research question six: Do differences in stage of change relate to work-related road safety outcomes? The interviews and questionnaires identified that participants’ perceptions of initiative effectiveness were found to vary with respect to their individual stage of readiness, with stage-matched initiatives being perceived most effective. In regards to safety outcomes, regression analyses identified that as participants’ progress through the stages of change, the corresponding likelihood of them being involved in vehicle crashes decreases. Research question seven: Do differences in safety ownership relate to work-related road safety outcomes? The interviews and questionnaires revealed that management of road risks is often given less attention than other areas of health and safety management in organisations. In regards to safety outcomes, regression analyses identified that perceived authority and perceived shared ownership both emerged as significant independent predictors of self-reported driving behaviours pertaining to fatigue and distractions. The regression models indicated that as participants’ perceptions of the authority of the person managing road risks increases, and perceptions of shared ownership of safety tasks increases, the corresponding likelihood of them engaging in driving while fatigued or multitasking while driving decreases. Based on the findings from the current research, the author makes several recommendations to assist practitioners in developing proactive and comprehensive approaches to managing occupational road risks. The author also suggests several avenues for future research in the area of work-related road safety.

The innovation deficit in public services : the curious problem of too much efficiency and not enough waste and failure

It has long been recognised that government and public sector services suffer an innovation deficit compared to private or market-based services. This paper argues that this can be explained as an unintended consequence of the concerted public sector drive toward the elimination of waste through efficiency, accountability and transparency. Yet in an evolving economy this can be a false efficiency, as it also eliminates the 'good waste' that is a necessary cost of experimentation. This results in a systematic trade0off in the public sector between the static efficiency of minimizing the misuse of public resources and the dynamic efficiency of experimentation. this is inherently biased against risk and uncertainty and therein, explains why governments find service innovation so difficult. In the drive to eliminate static inefficiencies, many political systems have susequently overshot and stifled policy innovation. I propose the 'Red Queen' solution of adaptive economic policy.