Development of an In Situ Measurement Device for Obtaining Material Thermal Properties

This thesis presents a methodology for measuring thermal properties in situ, with a special focus on obtaining properties of layered stack-ups commonly used in armored vehicle components. The technique involves attaching a thermal source to the surface of a component, measuring the heat flux transferred between the source and the component, and measuring the surface temperature response. The material properties of the component can subsequently be determined from measurement of the transient heat flux and temperature response at the surface alone. Experiments involving multilayered specimens show that the surface temperature response to a sinusoidal heat flux forcing function is also sinusoidal. A frequency domain analysis shows that sinusoidal thermal excitation produces a gain and phase shift behavior typical of linear systems. Additionally, this analysis shows that the material properties of sub-surface layers affect the frequency response function at the surface of a particular stack-up. The methodology involves coupling a thermal simulation tool with an optimization algorithm to determine the material properties from temperature and heat flux measurement data. Use of a sinusoidal forcing function not only provides a mechanism to perform the frequency domain analysis described above, but sinusoids also have the practical benefit of reducing the need for instrumentation of the backside of the component. Heat losses can be minimized by alternately injecting and extracting heat on the front surface, as long as sufficiently high frequencies are used.

A robust reference signal generator for synchronized ventricular assist devices

Ventricular assist devices (VADs) are blood pumps that offer an option to support the circulation of patients with severe heart failure. Since a failing heart has a remaining pump function, its interaction with the VAD influences the hemodynamics. Ideally, the heart's action is taken into account for actuating the device such that the device is synchronized to the natural cardiac cycle. To realize this in practice, a reliable real-time algorithm for the automatic synchronization of the VAD to the heart rate is required. This paper defines the tasks such an algorithm needs to fulfill: the automatic detection of irregular heart beats and the feedback control of the phase shift between the systolic phases of the heart and the assist device. We demonstrate a possible solution to these problems and analyze its performance in two steps. First, the algorithm is tested using the MIT-BIH arrhythmia database. Second, the algorithm is implemented in a controller for a pulsatile and a continuous-flow VAD. These devices are connected to a hybrid mock circulation where three test scenarios are evaluated. The proposed algorithm ensures a reliable synchronization of the VAD to the heart cycle, while being insensitive to irregularities in the heart rate.

Analysis of Pressure Head-Flow Loops of Pulsatile Rotodynamic Blood Pumps

The clinical importance of pulsatility is a recurring topic of debate in mechanical circulatory support. Lack of pulsatility has been identified as a possible factor responsible for adverse events and has also demonstrated a role in myocardial perfusion and cardiac recovery. A commonly used method for restoring pulsatility with rotodynamic blood pumps (RBPs) is to modulate the speed profile, synchronized to the cardiac cycle. This introduces additional parameters that influence the (un)loading of the heart, including the timing (phase shift) between the native cardiac cycle and the pump pulses, and the amplitude of speed modulation. In this study, the impact of these parameters upon the heart-RBP interaction was examined in terms of the pressure head-flow (HQ) diagram. The measurements were conducted using a rotodynamic Deltastream DP2 pump in a validated hybrid mock circulation with baroreflex function. The pump was operated with a sinusoidal speed profile, synchronized to the native cardiac cycle. The simulated ventriculo-aortic cannulation showed that the level of (un)loading and the shape of the HQ loops strongly depend on the phase shift. The HQ loops displayed characteristic shapes depending on the phase shift. Increased contribution of native contraction (increased ventricular stroke work [WS ]) resulted in a broadening of the loops. It was found that the previously described linear relationship between WS and the area of the HQ loop for constant pump speeds becomes a family of linear relationships, whose slope depends on the phase shift.

A Compensating Anastigmatic Submillimeter Array Imaging System for STEAMR

In this paper, we present a novel technique for the removal of astigmatism in submillimeter-wave optical systems through employment of a specific combination of so-called astigmatic off-axis reflectors. This technique treats an orthogonally astigmatic beam using skew Gaussian beam analysis, from which an anastigmatic imaging network is derived. The resultant beam is considered truly stigmatic, with all Gaussian beam parameters in the orthogonal directions being matched. This is thus considered an improvement over previous techniques wherein a beam corrected for astigmatism has only the orthogonal beam amplitude radii matched, with phase shift and phase radius of curvature not considered. This technique is computationally efficient, negating the requirement for computationally intensive numerical analysis of shaped reflector surfaces. The required optical surfaces are also relatively simple to implement compared to such numerically optimized shaped surfaces. This technique is implemented in this work as part of the complete optics train for the STEAMR antenna. The STEAMR instrument is envisaged as a mutli-beam limb sounding instrument operating at submillimeter wavelengths. The antenna optics arrangement for this instrument uses multiple off-axis reflectors to control the incident radiation and couple them to their corresponding receiver feeds. An anastigmatic imaging network is successfully implemented into an optical model of this antenna, and the resultant design ensures optimal imaging of the beams to the corresponding feed horns. This example also addresses the challenges of imaging in multi-beam antenna systems.

Mineralogy of sediment core GeoB3313-1

Geochemical and clay mineral parameters of a high accumulation marine sediment core from the Chilean continental slope (41°S) provide a 7700 yr record of rainfall variability in southern Chile related to the position of the Southern Westerlies. We especially use the iron content, measured with a time-resolution of ca. 10 yr on average, of 14C-accelerator mass spectrometry dated marine sediments as a proxy for the relative input of iron-poor Coastal Range and iron-rich Andean source rocks. Variations in this input are most likely induced by rainfall changes in the continental hinterland of the core position. Based on these interpretations, we find a pronounced rainfall variability on multi-centennial to millennial time-scales, superimposed on generally more arid conditions during the middle Holocene (7700 to 4000 cal yr B.P.) compared to the late Holocene (4000 to present). This variability and thus changes in the position of the Southern Westerlies are first compared to regional terrestrial paleoclimate data-sets from central and southern Chile. In order to derive possible wider implications and forcing mechanisms of the Holocene latitudinal shifts of the Southern Westerlies, we then compare our data to ice-core records from both tropical South America and coastal Antarctica. These records show similar bands of variability centered at ca. 900 and 1500 yr. Comparisons of band pass filters suggest a close connection of shifts of the Southern Westerlies to changes within the tropical climate system. The correlation to climate conditions in coastal Antarctica shows a more complicated picture with a phase shift at the beginning of the late Holocene coinciding with the onset of the modern state of El Niño-Southern Oscillation system. The presented data provide further evidence that the well known millennial-scale climate variability during the last glacial continued throughout the Holocene.

Stable isotope record and planktonic foraminiferal fragmentation of the late Pleistocene section of ODP Hole 134-828A

A high-resolution record of foraminiferal fragmentation (a dissolution indicator) for the last 250 k.y. (isotopic Stages 1 to 7) is identified in the upper 61.9 m of Ocean Drilling Program (ODP) Hole 828A, west Vanuatu. This record is comparable in detail to the atmospheric CO2 record and the d18O stack. Phase shifts between preservation spikes and maximum ice volumes (d18O of Globigerinoides sacculifer) are analogous to those on Ontong Java Plateau. Mass spectrometer (AMS14C) dating of a sample taken at the base of dissolution cycle B1 and the position of the last glacial maximum indicates a lag in time of ~8 k.y. in the Vanuatu region for the last glacial termination. When dissolution spikes are compared with minimum ice volumes there is no phase shift for the last two glacial terminations. The difference between Vanuatu and Ontong Java Plateau may be explained by local CO2 sinks and the interplay between intermediate and deep water masses. Terrigenous input increasingly affected sediment of Hole 828A on the North d'Entrecasteaux Ridge (NDR) as it approached Espiritu Santo Island. Mud and silt suspended in mid-water flows become important after 125 ka, while turbidites bypass the New Hebrides Trench only towards the last glacial maximum (LGM). Terrigenous supply seems to affect the lysocline profile that changed from an "open ocean" to a "near continent" type, thus favoring dissolution. Fragmentation of planktonic foraminifers is a more sensitive indicator of lysocline variations than is foraminiferal susceptibility to dissolution, the foraminiferal dissolution index, the abundance of benthic foraminifers, or CaCO3 content. A modern foraminiferal lysocline for the neighboring area (between 10°S and 30°S, and 160°E and 180°E) is found at 3.1 km below sea level, compared to west Vanuatu where it is shallower. The past lysocline level was deeper than 3086 m during intervals of dissolution minima, and ranged from ~2550 to 3000 m during intervals of dissolution maxima. The high sedimentation rates (in the order of 10 to 50 cm/k.y.) found in Hole 828A offer a great potential for future high-resolution studies either in this hole or other western localities along the NDR. Areas of high sedimentation near continental regions have been discarded for paleoceanographic and/or paleoclimatic studies. Nonetheless, conditions analogous to those found in Hole 828A are expected to occur in many trench areas around the world where mid-water flows have preserved as yet undiscovered fine high-resolution sedimentary records.

Foraminiferal abundance, carbonat concentration and dissolution index of sediment core W9903B-51GC

In order to investigate the paleoceanographic record of dissolution of calcium carbonate (CaCO3) in the central equatorial Pacific Ocean, we have studied the relationship between three indices of foraminiferal dissolution and the concentration and accumulation of CaCO3, opal, and Corg in Core WEC8803B-GC51 (1.3°N, 133.6°W; 4410 m). This core spans the past 413 kyr of deposition and moved in and out of the lysoclinal transition zone during glacial-interglacial cycles of CaCO3 production and dissolution. The record of dissolution intensity provided by foraminiferal fragmentation, the proportion of benthic foraminifera, and the foraminiferal dissolution index consistently indicates that the past corrosion of pelagic CaCO3 in the central equatorial Pacific does not vary with the observed sedimentary concentration of CaCO3. Although there is a weak low-frequency variation (~100 kyr) in dissolution intensity, it is unrelated to sedimentary CaCO3 concentration. There are many shorter-lived episodes where high CaCO3 concentration is coincident with poor foraminiferal preservation, and where, conversely, low CaCO3 concentration is coincident with superb foraminiferal preservation. Spectral analyses indicate that dissolution maxima consistently lagged glacial maxima (manifest by the SPECMAP delta18O stack) in the 100-kyr orbital band. Additionally, there is no relationship between dissolution and the accumulation of biogenic opal or Corg or between dissolution and the burial ratio of Corg/CINorg (calculated from Corg and CaCO3). Because previous studies of this core strongly suggest that surface water productivity varied closely with CaCO3 accumulation, both the mechanistic decoupling of carbonate dissolution from CaCO3 concentration (and from biogenic accumulation) and the substantial phase shift between dissolution and global glacial periodicity effectively obscure any simple link between export production, CaCO3 concentration, and dissolution of sedimentary CaCO3.