Remoção de cromo (VI) de soluções aquosas utilizando o compósito magnético calcinado hidrotalcita-óxido de ferro: estudo cinético e de equilíbrio termodinâmico

In this work, hydrotalcite, a layered double hydroxide, had its ion exchange properties combined with the magnetic properties of iron oxide to produce a magnetic adsorbent, HT-Fe 500. These magnetic composites can be used as adsorbents for anionic contaminants in water and subsequently removed from the medium by a simple magnetic process. Removal of chromium (VI) from aqueous solutions using HT-Fe 500 was achieved using batch adsorption experiments. The adsorption capacity, calculated with the Langmuir-Freundlich model showed to be dependent on temperature, reaching values of 25.93 and 48.31 mg g-1, respectively, for temperatures of 25 and 30 ºC.

Biosorption and removal of chromium from water by using moringa seed cake (Moringa oleifera Lam.)

This study evaluated the adsorption capacity of chromium from contaminated aqueous solutions by using Moringa oleifera Lam. seeds. Parameters such as solution pH, adsorbent mass, contact time between solution and adsorbent, isotherms, thermodynamic, kinetics, and desorption were evaluated. The maximum adsorption capacity (Qm) calculated to be 3.191 mg g-1 for the biosorbent. Activated carbon was used for comparison purposes in addition to the biosorbent. The best fit was obtained by the Langmuir model for both adsorbents. The average desorption value indicated that both the biosorbent and activated carbon have a strong interaction with the metal. The results showed that the biosorbent has advantages owing to its low cost and efficiency in Cr3+ removal from contaminated waters.

Adsorção de alfa-lactalbumina do soro de leite em hidroxiapatita: efeito do pH e da temperatura e análise termodinâmica

The nutritional and functional benefits offered by whey protein α-lactalbumin justify the great interest in its manufacture in large quantities at a high purity level. Hydroxyapatite is a calcium phosphate material able to adsorb proteins and can be synthesized at low production cost. Therefore, this work evaluated the adsorption of α-lactalbumin on hydroxyapatite using solid-liquid phase equilibrium data reported as adsorption isotherms. Van't Hoff's thermodynamics analysis showed that the adsorption process is entropically driven.

TUNGSTOPHOSPHORIC ACID HETEROGENIZED ONTO NH4ZSM5 AS AN EFFICIENT AND RECYCLABLE CATALYST FOR THE PHOTOCATALYTIC DEGRADATION OF DYES

Materials based on tungstophosphoric acid (TPA) immobilized on NH4ZSM5 zeolite were prepared by wet impregnation of the zeolite matrix with TPA aqueous solutions. Their concentration was varied in order to obtain TPA contents of 5%, 10%, 20%, and 30% w/w in the solid. The materials were characterized by N2 adsorption-desorption isotherms, XRD, FT-IR, 31P MAS-NMR, TGA-DSC, DRS-UV-Vis, and the acidic behavior was studied by potentiometric titration with n-butylamine. The BET surface area (SBET) decreased when the TPA content was raised as a result of zeolite pore blocking. The X-ray diffraction patterns of the solids modified with TPA only presented the characteristic peaks of NH4ZSM5 zeolites, and an additional set of peaks assigned to the presence of (NH4)3PW12O40. According to the Fourier transform infrared and 31P magic angle spinning-nuclear magnetic resonance spectra, the main species present in the samples was the [PW12O40]3- anion, which was partially transformed into the [P2W21O71]6- anion during the synthesis and drying steps. The thermal stability of the NH4ZSM5TPA materials was similar to that of their parent zeolites. Moreover, the samples with the highest TPA content exhibited band gap energy values similar to those reported for TiO2. The immobilization of TPA on NH4ZSM5 zeolite allowed the obtention of catalysts with high photocatalytic activity in the degradation of methyl orange dye (MO) in water, at 25 ºC. These can be reused at least three times without any significant decrease in degree of degradation.

EFEITO DO DIOXIDO DE CARBONO SOBRE A ESTABILIDADE DA FASE Ca2Fe2O5 APLICADA NO PROCESSO DE DEGRADAÇÃO FOTOCATALITICO DO AZUL DE METILENO

Solid samples containing a Ca2Fe2O5 phase were synthesized using the Pechini method. The samples were characterized using X-ray diffraction, thermogravimetric analysis, differential thermal analysis, X-ray fluorescence, nitrogen adsorption/desorption isotherms, and scanning electron microscopy. The stability of the Ca2Fe2O5 phase was evaluated in the photocatalytic degradation of methylene blue (MB) in aqueous solution in the presence of bubbling gas (air, N2, or CO2). The presence of CO2 is known to suppress MB degradation. After the photocatalytic test, changes were observed in the crystalline phase of all systems. These results suggest the low stability of the Ca2Fe2O5 phase in aqueous systems and the significant effect of CO2 on the photocatalytic activity of the Ca2Fe2O5 phase.

Hidrogeneoftalato de potássio como molécula modelo para estudos de adsorção sobre TiO2

Este trabalho teve por objetivo utilizar o hidrogenoftalato de potássio como molécula modelo para estudos de adsorção em TiO2. Os resultados de adsorção do hidrogeneoftalato sobre TiO2 se ajustaram aos modelos de adsorção propostos por Langmuir e Freundlich, sendo que o modelo de Freundlich descreveu melhor o fenômeno. A adsorção foi função da temperatura e a capacidade de adsorção aumentou de 2,4 para 4,5 mg.g-1 quando se elevou a temperatura de 20 para 30ºC.

Estudo da adsorção/dessorção de 2,4-D em solos usando técnica cromatográfica

Este trabalho estudou a adsorção e a desorção do herbicida ácido 2,4-Diclorofenoxiacético (2,4-D) em solo da região de Urbano Santos - MA. A região possui campos de cultivo de eucaliptos para obtenção de celulose. Para a limpeza dos campos, antes da plantação e nos primeiros 12 meses de plantio, são aplicados herbicidas, dentre os quais destacamos o 2,4-D. A isoterma de Freundlich foi utilizado como modelo para este estudo e a concentração de 2,4-D foi determinada por cromatografia líquida de alta eficiência (CLAE), acompanhada de ensaios de recuperação para garantir a confiabilidade dos dados obtidos na investigação de adsorção/dessorção. Os resultados indicaram que o 2,4-D apresenta maior adsorção à matéria orgânica do solo estudado, quando comparado a outros tipos de solo, o que pode resultar em pequena diminuição em sua tendência de lixiviação e de degradação microbiológica. Entretanto, este herbicida apresenta elevado potencial de lixiviação quando comparado a outros pesticidas.

Influence of the synthesis conditions on the characteristics and metal adsorption properties of the 3-(1,4-phenylenediamine)propylsilica xerogel

The hybrid 3-(1,4-phenylenediamine)propylsilica xerogel was obtained starting from two different organic precursor quantity (5 and 8 mmol) to 22 mmol of TEOS, in the synthesis. The xerogel samples were characterized by using CHN elemental analysis, N2 adsorption-desorption isotherms, infrared thermal analysis. The xerogel was used as metal sorbent for Cu2+, Cd2+ and Pb2+ in aqueous solution with concentration range of 10-3 to 10-5 mmol l-1. The quantity of organic precursor added in the synthesis influences the characteristics of the xerogel as morphology and thermal stability, as well as the metal adsorption capacity.

A water soluble 3-n-propyl-1-azonia-4-azabicyclo[2.2.2]octanechloride silsesquioxane grafted onto Al/SiO2 surface: chromium adsorption study

The water soluble material, 3-n-propyl-1-azonia-4-azabicyclo[2.2.2]octanechloride silsesquioxane (dabcosil silsesquioxane) was obtained. The dabcosil silsesquioxane was grafted onto a silica surface, previously modified with aluminum oxide. The resulting solid, dabcosil-Al/SiO2, presents 0.15 mmol of dabco groups per gram of material. The product of the grafting reaction was analyzed by infrared spectroscopy and N2 adsorption-desorption isotherms. The dabcosil-Al/SiO2 material was used as sorbent for chromium (VI) adsorption in aqueous solution.

Immersion enthalpy variation of surface-modified mineral activated carbon in lead (II) aqueous solution adsorption: the relation between immersion enthalpy and adsorption capacity

An activated carbon was obtained by chemical activation with phosphoric acid, CM, from a mineral carbon. Afterwards, the carbon was modified with 2 and 5 molL-1, CMox2 and CMox5 nitric acid solutions to increase the surface acid group contents. Immersion enthalpy at pH 4 values and Pb2+ adsorption isotherms were determined by immersing activated carbons in aqueous solution. The surface area values of the adsorbents and total pore volume were approximately 560 m².g-1 and 0.36 cm³g-1, respectively. As regards chemical characteristics, activated carbons had higher acid sites content, 0.92-2.42 meq g-1, than basic sites, 0.63-0.12 meq g-1. pH values were between 7.4 and 4.5 at the point of zero charge, pH PZC. The adsorbed quantity of Pb2+ and the immersion enthalpy in solution of different pH values for CM activated carbon showed that the values are the highest for pH 4, 15.7 mgg-1 and 27.6 Jg-1 respectively. Pb2+ adsorption isotherms and immersion enthalpy were determined for modified activated carbons and the highest values were obtained for the activated carbon that showed the highest content of total acid sites on the surface.

Adsorption isotherm studies of Cd (II), Pb (II) and Zn (II) ions bioremediation from aqueous solution using unmodified and EDTA-modified maize cob

The need to clean-up heavy metal contaminated environment can not be over emphasized. This paper describes the adsorption isotherm studies of Cd (II), Pb (II) and Zn (II) ions from aqueous solution using unmodified and EDTA-modified maize cob. Maize cob was found to be an excellent adsorbent for the removal of these metal ions. The amount of metal ions adsorbed increased as the initial concentration increased. Also, EDTA - modification enhanced the adsorption capacity of maize cob probably due to the chelating ability of EDTA. Among the three adsorption isotherm tested, Dubinin-Radushkevich gave the best fit with R² value ranging from 0.9539 to 0.9973 and an average value of 0.9819. This is followed by Freundlich isotherm (Ave. 0.9783) and then the Langmuir isotherm (Ave. 0.7637). The sorption process was found to be a physiosorption process as seen from the apparent energy of adsorption which ranged from 2.05KJ\mol to 4.56KJ\mol. Therefore, this study demonstrates that maize cob which is an environmental pollutant could be used to adsorb heavy metals and achieve cleanliness thereby abating environmental nuisance caused by the maize cob.

Aplicação de Al-PILC na adsorção de Cu2+, Ni2+e Co2+ utilizando modelos físico-químicos de adsorção

Amostra de esmectita pertencente a Serra de Maicuru (Estado do Pará, Norte do Brasil, região amazônica) foi pilarizada com Al13, A Argila pilarizada com alumínio (Al-PILC) foi caracterizada por DRX, MEV e EDS. Para a análise textural foram utilizadas isotermas de adsorção-desorção utilizando o nitrogênio. Este artigo é dirigido ao estudo da adsorção de metais pesados. A adsorção dos íons de Cu2+, Ni2+e Co2+ foi realizadas com a matriz Al-PILC em temperatura ambiente com soluções aquosas contendo os íons metálicos. Os modelos de adsorção adotados foram os de Langmuir, Freundlich e Temkin que foram aplicados aos valores obtidos experimentalmente com regressão linear. A equação de Langmuir foi o melhor modelo de linearização com r = 0,999. A equação de Freundlich apresentou limitações em altas concentrações, mas foram obtidos valores (Kf e n) bastante aceitáveis utilizando este modelo. Os parâmetros foram utilizados para calcular a quantidade de Nf em função de Cs.

Design of an adsorbent employing activated carbon fiber to remove lead

Zorflex® activated carbon fibers (ACF), reference FM100 198B, are used before and after an oxidizing procedure with H3PO4 to study the adsorption of Pb2+. The point of zero charge was determined for the modified and unmodified fiber giving values of 2.3 and 4.3, respectively. After oxidizing the ACF, the fiber showed to have a greater Pb2+ adsorption capacity in comparison with the unmodified fiber, which is related with the acid sites increase, where lead was mainly adsorbed. Determination of the BET area was carried out by nitrogen physisorption at 77K. ACFs presented superficial areas between 1000 and 1500 m²/g showing mostly, a microporous structure. The preliminary design of an adsorbent using the modified fiber is presented where the fiber superior physicochemical properties over the unmodified one are observed.

Aplicação de material zeolítico sintetizado de cinzas de carvão como adsorvente de poluentes em água

Cinzas leve de carvão tratadas pelo método hidrotérmico foram usadas como adsorvente de baixo custo para a remoção de íons metálicos e corante de solução aquosa. As isotermas de adsorção das cinzas leve tratadas foram estudadas e os resultados foram ajustados pelos modelos de Langmuir e Freundlich. A isoterma de Freundlich descreveu melhor o processo de adsorção do azul de metileno. Os dados de equilíbrio para a adsorção dos íons zinco e cádmio se ajustaram melhor á equação de Langmuir. O valor máximo de capacidade de adsorção obtido foi de 0,78 (mg g-1)(L mg)1/n para o azul de metileno, 38,1 mg g-1 para o Zn2+ e 67, 5 mg g-1 para o Cd2+. Os materiais sintetizados exibiram capacidades de adsorção muito maiores do que as das cinzas leves usadas como matéria-prima. O estudo mostrou que o material zeólitico pode efetivamente adsorver azul de metileno e íons metálicos com eficiências de remoção na faixa de 82-99%.

Epäpuhtausmetallien talteenotto sinkkiprosessissa

There are small amounts of valuable metals, such as indium, gallium and germanium, in zinc process solutions. Their solvent extraction was studied in this work in sulphate solutions containing zinc and other metals present in industrial solutions. It was discovered, that a commercial bis(2-ethylhexyl)phosphate (D2EHPA) extractant can be used to extract indium and gallium. Indium was extracted separately at a higher acid concentration than gallium. Zinc was co-extracted faster than gallium and almost as much as gallium at the same pH. However, the scrubbing of zinc was possible using a dilute sulphuric acid and a short contact time while gallium losses were small. Both indium and gallium were stripped with sulphuric acid. Germanium was extracted with 5,8-diethyl-7-hydroxydodecane-6-oxime with the commercial name of LIX 63. Unlike other metals in the solution the extraction of germanium increased with different extractants as the acidity increased. Germanium extraction isotherm was measured for a 125 g/L sulfuric acid solution. The loaded organic phase was washed with pure water. It removed the co-extracted acid and part of the germanium and extracted impurities such as iron and copper. Germanium was stripped using a NaOH solution. A process model utilizing own experimentally determined extraction, scrubbing and stripping isotherms was made with HSC Sim software developed by Outotec Oyj. The model based on McCabe–Thiele diagrams was used in sizing the necessary amount of stages and phase ratios in a recovery process. It was concluded, that indium, gallium and germanium can be recovered in the process from a feed where their concentrations are low (<300 ppm). In an example case the feed contained also more than 20 g/L zinc and 2–8 g/L iron, aluminium and copper. The recoveries of indium, gallium and germanium were more than 90 % when 1–3 stages were used in each extraction, scrubbing and stripping section. Since the number of stages is small mixer-settlers would be well suited for this purpose.