Study of Friction and Transfer Layer Formation in Copper-Steel Tribo-System: Role of Surface Texture and Roughness Parameters

In the present investigation, experiments were conducted on a tribological couple-copper pin against steel plate-using an inclined pin-on-plate sliding tester to understand the role of surface texture and roughness parameters of the plate on the coefficient friction and transfer layer formation. Two surface characteristics of the steel plates-roughness and texture-were varied in the tests. It was observed that the transfer layer formation and the coefficient of friction along with its two components, namely, the adhesion and plowing, are controlled by the surface texture of the plate. The plowing component of friction was highest for the surface texture that promotes plane strain conditions while it was lowest for the texture that favors plane stress conditions at the interface. Dimensionless quantifiable roughness parameters were formulated to describe the degree of plowing and hence the plane strain/stress type deformations taking place at the asperity level.

Thermal characterization of microheaters from the dynamic response

Thermal characterization of surface-micromachined microheaters is carried out from their dynamic response to electrothermal excitations. An electrical equivalent circuit model is developed for the thermo-mechanical system. The mechanical parameters are extracted from the frequency response obtained using a laser Doppler vibrometer. The resonant frequencies of the microheaters are measured and compared with FEM simulations. The thermal time constants are obtained from the electrical equivalent model by fitting the model response to the measured frequency response. Microheaters with an active area of 140 µm × 140 µm have been realized on two different layers (poly-1 and poly-2) with two different air gaps (2 µm and 2.75 µm). The effective time constants, combining thermal and mechanical responses, are in the range of 0.13–0.22 ms for heaters on the poly-1 layer and 1.9 µs–0.15 ms for microheaters on the poly-2 layer. The thermal time constants of the microheaters are in the range of a few microseconds, thus making them suitable for sensor applications that need a faster thermal response.

Simultaneous prediction of acidity parameters (pH and titratable acidity) in Kefir using near infrared reflectance spectroscopy.

Acidity in terms of pH and titratable acids influences the texture and flavour of fermented dairy products, such as Kefir. However, the methods for determining pH and titratable acidity (TA) are time consuming. Near infrared (NIR) spectroscopy is a non-destructive method, which simultaneously predicts multiple traits from a single scan and can be used to predict pH and TA. The best pH NIR calibration model was obtained with no spectral pre-treatment applied, whereas smoothing was found to be the best pre-treatment to develop the TA calibration model. Using cross-validation, the prediction results were found acceptable for both pH and TA. With external validation, similar results were found for pH and TA, and both models were found to be acceptable for screening purposes.

Male traits and herd reproductive capability in tropical beef cattle. 2. Genetic parameters of bull traits

A total of 4063 young bulls of two tropical genotypes (1639 Brahman and 2424 Tropical Composite) raised in northern Australia were evaluated for a comprehensive range of production and reproduction traits up to 24 months of age. Prior to weaning, peripheral blood concentrations of luteinising hormone (LH) and inhibin were measured at 4 months of age. At weaning (6 months) blood insulin-like growth factor-1 (IGF-I) and flight time were recorded. Body composition traits of fat depth and eye-muscle area were determined by ultrasonography at 15 months of age when additional measurements of liveweight, hip height and body condition score were recorded. Bull breeding soundness was evaluated at similar to 12, 18 and 24 months of age when measurements of scrotal circumference, sheath score, semen mass activity, progressive motility of individual sperm and percent morphologically normal sperm were recorded. Magnitude of heritability and genetic correlations changed across time for some traits. Heritability of LH, inhibin, IGF-I and of 18-month scrotal circumference, mass activity, progressive motility and percent normal sperm was 0.31, 0.74, 0.44, 0.75, 0.24, 0.15 and 0.25, respectively, for Brahmans and 0.48, 0.72, 0.36, 0.43, 0.13, 0.15 and 0.20, respectively, for Tropical Composites. Inhibin and IGF-I had moderate genetic association with percent normal sperm at 24 months in Brahmans but low to negligible associations in Tropical Composites. Body condition score in Brahmans and sperm motility (mass and individual) traits in both genotypes had moderate to strong genetic correlation with percent normal sperm and may prove useful candidates for indirect selection. There is scope to increase scrotal circumference by selection and this will be associated with favourable correlated responses of improved semen quality in both genotypes. The lack of genetic antagonism among bull traits indicates that selection for improved semen quality will not adversely affect other production traits.

Optimal simultaneous maximum a posterioriestimation of states, noise statistics and parameters I. Algorithm

The simultaneous state and parameter estimation problem for a linear discrete-time system with unknown noise statistics is treated as a large-scale optimization problem. The a posterioriprobability density function is maximized directly with respect to the states and parameters subject to the constraint of the system dynamics. The resulting optimization problem is too large for any of the standard non-linear programming techniques and hence an hierarchical optimization approach is proposed. It turns out that the states can be computed at the first levelfor given noise and system parameters. These, in turn, are to be modified at the second level.The states are to be computed from a large system of linear equations and two solution methods are considered for solving these equations, limiting the horizon to a suitable length. The resulting algorithm is a filter-smoother, suitable for off-line as well as on-line state estimation for given noise and system parameters. The second level problem is split up into two, one for modifying the noise statistics and the other for modifying the system parameters. An adaptive relaxation technique is proposed for modifying the noise statistics and a modified Gauss-Newton technique is used to adjust the system parameters.

Optimal simultaneous maximum a posterioriestimation of states, noise statistics and parameters II. Numerical performance

A very general and numerically quite robust algorithm has been proposed by Sastry and Gauvrit (1980) for system identification. The present paper takes it up and examines its performance on a real test example. The example considered is the lateral dynamics of an aircraft. This is used as a vehicle for demonstrating the performance of various aspects of the algorithm in several possible modes.

Performance parameters of some new hybrid hypergols

Abstract is not available.

Land leasing, land degradation and agricultural productivity in Finland

This study analysed whether the land tenure insecurity problem has led to a decline in long-term land improvements (liming and phosphorus fertilization) under the Common Agricultural Policy (CAP) and Nordic production conditions in European Union (EU) countries such as Finland. The results suggests that under traditional cash lease contracts, which are encouraged by the existing land leasing regulations and agricultural subsidy programs, the land tenure insecurity problem on leased land reduces land improvements that have a long pay-back period. In particular, soil pH was found to be significantly lower on land cultivated under a lease contract compared to land owned by the farmers themselves. The results also indicate that land improvements could not be reversed by land markets, because land owners would otherwise have carried out land improvements even if not farming by themselves. To reveal the causality between land tenure and land improvements, the dynamic optimisation problem was solved by a stochastic dynamic programming routine with known parameters for one-period returns and transition equations. The model parameters represented Finnish soil quality and production conditions. The decision rules were solved for alternative likelihood scenarios over the continuation of the fixed-term lease contract. The results suggest that as the probability of non-renewal of the lease contract increases, farmers quickly reduce investments in irreversible land improvements and, thereafter, yields gradually decline. The simulations highlighted the observed trends of a decline in land improvements on land parcels that are cultivated under lease contracts. Land tenure has resulted in the neglect of land improvement in Finland. This study aimed to analyze whether these challenges could be resolved by a tax policy that encourages land sales. Using Finnish data, real estate tax and a temporal relaxation on the taxation of capital gains showed some potential for the restructuring of land ownership. Potential sellers who could not be revealed by traditional logit models were identified with the latent class approach. Those landowners with an intention to sell even without a policy change were sensitive to temporal relaxation in the taxation of capital gains. In the long term, productivity and especially productivity growth are necessary conditions for the survival of farms and the food industry in Finland. Technical progress was found to drive the increase in productivity. The scale had only a moderate effect and for the whole study period (1976–2006) the effect was close to zero. Total factor productivity (TFP) increased, depending on the model, by 0.6–1.7% per year. The results demonstrated that the increase in productivity was hindered by the policy changes introduced in 1995. It is also evidenced that the increase in land leasing is connected to these policy changes. Land institutions and land tenure questions are essential in agricultural and rural policies on all levels, from local to international. Land ownership and land titles are commonly tied to fundamental political, economic and social questions. A fair resolution calls for innovative and new solutions both on national and international levels. However, this seems to be a problem when considering the application of EU regulations to member states inheriting divergent landownership structures and farming cultures. The contribution of this study is in describing the consequences of fitting EU agricultural policy to Finnish agricultural land tenure conditions and heritage.

Estimation of cosmological parameters using adaptive importance sampling

We present a Bayesian sampling algorithm called adaptive importance sampling or population Monte Carlo (PMC), whose computational workload is easily parallelizable and thus has the potential to considerably reduce the wall-clock time required for sampling, along with providing other benefits. To assess the performance of the approach for cosmological problems, we use simulated and actual data consisting of CMB anisotropies, supernovae of type Ia, and weak cosmological lensing, and provide a comparison of results to those obtained using state-of-the-art Markov chain Monte Carlo (MCMC). For both types of data sets, we find comparable parameter estimates for PMC and MCMC, with the advantage of a significantly lower wall-clock time for PMC. In the case of WMAP5 data, for example, the wall-clock time scale reduces from days for MCMC to hours using PMC on a cluster of processors. Other benefits of the PMC approach, along with potential difficulties in using the approach, are analyzed and discussed.

Estimates of genetic parameters for growth and wood properties in Eucalyptus pellita F. Muell. to support tree breeding in Vietnam

Key message Eucalyptus pellita demonstrated good growth and wood quality traits in this study, with young plantation grown timber being suitable for both solid and pulp wood products. All traits examined were under moderate levels of genetic control with little genotype by environment interaction when grown on two contrasting sites in Vietnam. Context Eucalyptus pellita currently has a significant role in reforestation in the tropics. Research to support expanded of use of this species is needed: particularly, research to better understand the genetic control of key traits will facilitate the development of genetically improved planting stock. Aims This study aimed to provide estimates of the heritability of diameter at breast height over bark, wood basic density, Kraft pulp yield, modulus of elasticity and microfibril angle, and the genetic correlations among these traits, and understand the importance of genotype by environment interactions in Vietnam. Methods Data for diameter and wood properties were collected from two 10-year-old, open-pollinated progeny trials of E. pellita in Vietnam that evaluated 104 families from six native range and three orchard sources. Wood properties were estimated from wood samples using near-infrared (NIR) spectroscopy. Data were analysed using mixed linear models to estimate genetic parameters (heritability, proportion of variance between seed sources and genetic correlations). Results Variation among the nine sources was small compared to additive variance. Narrow-sense heritability and genetic correlation estimates indicated that simultaneous improvements in most traits could be achieved from selection among and within families as the genetic correlations among traits were either favourable or close to zero. Type B genetic correlations approached one for all traits suggesting that genotype by environment interactions were of little importance. These results support a breeding strategy utilizing a single breeding population advanced by selecting the best individuals across all seed sources. Conclusion Both growth and wood properties have been evaluated. Multi-trait selection for growth and wood property traits will lead to more productive populations of E. pellita both with improved productivity and improved timber and pulp properties.

Prediction of masonry compressive behaviour using a damage mechanics inspired modelling method

Masonry under compression is affected by the properties of its constituents and their interfaces. In spite of extensive investigations of the behaviour of masonry under compression, the information in the literature cannot be regarded as comprehensive due to ongoing inventions of new generation products – for example, polymer modified thin layer mortared masonry and drystack masonry. As comprehensive experimental studies are very expensive, an analytical model inspired by damage mechanics is developed and applied to the prediction of the compressive behaviour of masonry in this paper. The model incorporates a parabolic progressively softening stress-strain curve for the units and a progressively stiffening stress-strain curve until a threshold strain for the combined mortar and the unit-mortar interfaces is reached. The model simulates the mutual constraints imposed by each of these constituents through their respective tensile and compressive behaviour and volumetric changes. The advantage of the model is that it requires only the properties of the constituents and considers masonry as a continuum and computes the average properties of the composite masonry prisms/wallettes; it does not require discretisation of prism or wallette similar to the finite element methods. The capability of the model in capturing the phenomenological behaviour of masonry with appropriate elastic response, stiffness degradation and post peak softening is presented through numerical examples. The fitting of the experimental data to the model parameters is demonstrated through calibration of some selected test data on units and mortar from the literature; the calibrated model is shown to predict the responses of the experimentally determined masonry built using the corresponding units and mortar quite well. Through a series of sensitivity studies, the model is also shown to predict the masonry strength appropriately for changes to the properties of the units and mortar, the mortar joint thickness and the ratio of the height of unit to mortar joint thickness. The unit strength is shown to affect the masonry strength significantly. Although the mortar strength has only a marginal effect, reduction in mortar joint thickness is shown to have a profound effect on the masonry strength. The results obtained from the model are compared with the various provisions in the Australian Masonry Structures Standard AS3700 (2011) and Eurocode 6.

Parameters Affecting the Extraction of Polycyclic Aromatic Hydrocarbons with Pressurised Hot Water

Pressurised hot water extraction (PHWE) exploits the unique temperature-dependent solvent properties of water minimising the use of harmful organic solvents. Water is environmentally friendly, cheap and easily available extraction medium. The effects of temperature, pressure and extraction time in PHWE have often been studied, but here the emphasis was on other parameters important for the extraction, most notably the dimensions of the extraction vessel and the stability and solubility of the analytes to be extracted. Non-linear data analysis and self-organising maps were employed in the data analysis to obtain correlations between the parameters studied, recoveries and relative errors. First, pressurised hot water extraction (PHWE) was combined on-line with liquid chromatography-gas chromatography (LC-GC), and the system was applied to the extraction and analysis of polycyclic aromatic hydrocarbons (PAHs) in sediment. The method is of superior sensitivity compared with the traditional methods, and only a small 10 mg sample was required for analysis. The commercial extraction vessels were replaced by laboratory-made stainless steel vessels because of some problems that arose. The performance of the laboratory-made vessels was comparable to that of the commercial ones. In an investigation of the effect of thermal desorption in PHWE, it was found that at lower temperatures (200ºC and 250ºC) the effect of thermal desorption is smaller than the effect of the solvating property of hot water. At 300ºC, however, thermal desorption is the main mechanism. The effect of the geometry of the extraction vessel on recoveries was studied with five specially constructed extraction vessels. In addition to the extraction vessel geometry, the sediment packing style and the direction of water flow through the vessel were investigated. The geometry of the vessel was found to have only minor effect on the recoveries, and the same was true of the sediment packing style and the direction of water flow through the vessel. These are good results because these parameters do not have to be carefully optimised before the start of extractions. Liquid-liquid extraction (LLE) and solid-phase extraction (SPE) were compared as trapping techniques for PHWE. LLE was more robust than SPE and it provided better recoveries and repeatabilities than did SPE. Problems related to blocking of the Tenax trap and unrepeatable trapping of the analytes were encountered in SPE. Thus, although LLE is more labour intensive, it can be recommended over SPE. The stabilities of the PAHs in aqueous solutions were measured using a batch-type reaction vessel. Degradation was observed at 300ºC even with the shortest heating time. Ketones and quinones and other oxidation products were observed. Although the conditions of the stability studies differed considerably from the extraction conditions in PHWE, the results indicate that the risk of analyte degradation must be taken into account in PHWE. The aqueous solubilities of acenaphthene, anthracene and pyrene were measured, first below and then above the melting point of the analytes. Measurements below the melting point were made to check that the equipment was working, and the results were compared with those obtained earlier. Good agreement was found between the measured and literature values. A new saturation cell was constructed for the solubility measurements above the melting point of the analytes because the flow-through saturation cell could not be used above the melting point. An exponential relationship was found between the solubilities measured for pyrene and anthracene and temperature.

Application of Artificial Viscosity in Establishing Supercritical Solutions to the Transonic Integra

The nonlinear singular integral equation of transonic flow is examined in the free-stream Mach number range where only solutions with shocks are known to exist. It is shown that, by the addition of an artificial viscosity term to the integral equation, even the direct iterative scheme, with the linear solution as the initial iterate, leads to convergence. Detailed tables indicating how the solution varies with changes in the parameters of the artificial viscosity term are also given. In the best cases (when the artificial viscosity is smallest), the solutions compare well with known results, their characteristic feature being the representation of the shock by steep gradients rather than by abrupt discontinuities. However, 'sharp-shock solutions' have also been obtained by the implementation of a quadratic iterative scheme with the 'artificial viscosity solution' as the initial iterate; the converged solution with a sharp shock is obtained with only a few more iterates. Finally, a review is given of various shock-capturing and shock-fitting schemes for the transonic flow equations in general, and for the transonic integral equation in particular, frequent comparisons being made with the approach of this paper.

Pen parameters for improving the performance of sheep imported from Australia to Persian Gulf feedlots

Summer in the Persian Gulf region presents physiological challenges for Australian sheep that are part of the live export supply chain coming from the Australian winter. Many feedlots throughout the Gulf have very high numbers of animals during June to August in order to cater for the increased demand for religious festivals. From an animal welfare perspective it is important to understand the necessary requirements of feed and water trough allowances, and the amount of pen space required, to cope with exposure to these types of climatic conditions. This study addresses parameters that are pertinent to the wellbeing of animals arriving in the Persian Gulf all year round. Three experiments were conducted in a feedlot in the Persian Gulf between March 2010 and February 2012, totalling 44 replicate pens each with 60 or 100 sheep. The applied treatments covered animal densities, feed-bunk lengths and water trough lengths. Weights, carcass attributes and health status were the key recorded variables. Weight change results showed superior performance for animal densities of ≥1.2 m2/head during hot conditions (24-h average temperatures greater than 33 °C, or a diurnal range of around 29–37 °C). However the space allowance for animals can be decreased, with no demonstrated detrimental effect, to 0.6 m2/head under milder conditions. A feed-bunk length of ≥5 cm/head is needed, as 2 cm/head showed significantly poorer animal performance. When feeding at 90 ad libitum 10 cm/head was optimal, however under a maintenance feeding regime (1 kg/head/day) 5 cm/head was adequate. A minimum water trough allowance of 1 cm/head is required. However, this experiment was conducted during milder conditions, and it may well be expected that larger water trough lengths would be needed in hotter conditions. Carcass weights were determined mainly by weights at feedlot entry and subsequent weight gains, while dressing percentage was not significantly affected by any of the applied treatments. There was no demonstrated effect of any of the treatments on the number of animals that died, or were classified as unwell. However, across all the treatments, these animals lost significantly more weight than the healthy animals, so the above recommendations, which are aimed at maintaining weight, should also be applicable for good animal health and welfare. Therefore, best practice guidelines for managing Australian sheep in Persian Gulf feedlots in the hottest months (June–August) which present the greatest environmental and physical challenge is to allow feed-bunk length 5 cm/head on a maintenance-feeding program and 10 cm/head for 90 ad libitum feeding, and the space allowance per animal should be ≥1.2 m2/head. Water trough allocation should be at least 1 cm/head with provision for more in the summer when water intake potentially doubles.