AVALIAÇÃO DE PROPRIEDADES FÍSICAS E QUÍMICAS DE ELETRODEPÓSITOS DE Ni-W-P OBTIDOS EM CÉLULA DE HULL

Ni–W–P electrodeposits were synthesized in a Hull cell in order to simulate the obtainment under industrial conditions. Complete coverage of panels was accomplished by applying total currents of 1.0 and 2.0 A. Panels obtained with a current of 1.0 A appeared brighter. The best compositional uniformities, as determined by Energy Dispersive Spectrometer (EDS) occurred in the current density ranges of 0.6 to 3.0 A dm−2 and 1.6 to 6.0 A dm−2 obtained with 1.0 and 2.0 A, respectively. However, the best morphological characteristics, as determined by Scanning Electro Microscope (SEM), were observed in those obtained with a total current of 1.0 A. Analysis of corrosion resistance by Electrochemical Impedance Spectroscopy (EIS) and Potentiodynamic Linear Polarization (PLP) in NaCl have shown significant variations in the amount of corrosion potential, polarization resistance, and even total impedance. The alloys exhibited amorphous character (XRD) and crystallized above 400 °C to Ni and Ni3P phases, and possibly Ni–W, with a subsequent increase in hardness. The results suggest that under industrial conditions, current density variations due to the large and complex geometric shapes of substrates lead to formation of distinct alloys. Furthermore, these materials are potential substitutes for chromium deposits in many applications.

DESENVOLVIMENTO DE EXPERIMENTO DIDÁTICO DE ELETROGRAVIMETRIA DE BAIXO CUSTO UTILIZANDO PRINCÍPIOS DA QUÍMICA VERDE

In this paper, we describe the development of low-cost teaching experiments of electrogravimetry for undergraduate students using principles of green chemistry. Copper was electrochemically deposited on brass under an electrical current density of 50 mA cm−2 from acidic solutions containing nitrate anions. Color changes at the brass electrode and of the solution were observed, indicating that the reduction of copper ions had occurred. The deposition efficiency values were between 92.8% and 93.8%, and the electrochemical efficiency values were between 85.6% and 86.5%. There was no significant contribution from parallel reactions. These experimental conditions facilitated the didactic exploration of gravimetric and electrochemical concepts. Following the principles of green chemistry, the experiments produced no toxic substances, all the materials could be recycled, and the energy consumption was the lowest. For this reason, this experiment was considered to be very interesting for didactical purposes.

Magnetic sputtering of complex oxides

HTSC materials are relevant in modern microelectronics, because of their transformation from the normal state to the superconducting. That is why the idea of producing HTSC in industrial amounts is actual nowadays. To decrease cost of their production it is important to use magnetron sputtering systems which give the best results for essential parameters. Modeling is the simplest and the fastest way to determine optimum sputtering condition. This thesis concentrates on determination the phases of the whole sputtering process and to find out basic factors of each phase using the modeling. It was find out, that the main factors which influence on the mode of occurrence of the initial stages are the current density of the magnetron discharge and the pressure of sputtering gas. With the modeling also velocity dependences were obtained for YBCO and SmFeAsO. These were compared and difference between them was examined. To support represented model comparison was made with experimental results. This showed that the model gives good results, very similar to the experimental ones. The results of this work were published in annual conference of the finnish physical society.

Sewage Sludge Electro-Dewatering

Original sludge from wastewater treatment plants (WWTPs) usually has a poor dewaterability. Conventionally, mechanical dewatering methods are used to increase the dry solids (DS) content of the sludge. However, sludge dewatering is an important economic factor in the operation of WWTPs, high water content in the final sludge cake is commonly related to an increase in transport and disposal costs. Electro‐dewatering could be a potential technique to reduce the water content of the final sludge cake, but the parameters affecting the performance of electro‐dewatering and the quality of the resulting sludge cake, as well as removed water, are not sufficiently well known. In this research, non‐pressure and pressure‐driven experiments were set up to investigate the effect of various parameters and experimental strategies on electro‐dewatering. Migration behaviour of organic compounds and metals was also studied. Application of electrical field significantly improved the dewatering performance in comparison to experiments without electric field. Electro‐dewatering increased the DS content of the sludge from 15% to 40 % in non‐pressure applications and from 8% to 41% in pressure‐driven applications. DS contents were significantly higher than typically obtained with mechanical dewatering techniques in wastewater treatment plant. The better performance of the pressure‐driven dewatering was associated to a higher current density at the beginning and higher electric field strength later on in the experiments. The applied voltage was one of the major parameters affecting dewatering time, water removal rate and DS content of the sludge cake. By decreasing the sludge loading rate, higher electrical field strength was established between the electrodes, which has a positive effect on an increase in DS content of the final sludge cake. However interrupted voltage application had anegative impact on dewatering in this study, probably because the off‐times were too long. Other factors affecting dewatering performance were associated to the original sludge characteristics and sludge conditioning. Anaerobic digestion of the sludge with high pH buffering capacity, polymer addition and freeze/thaw conditioning had a positive impact on dewatering. The impact of pH on electro‐dewatering was related to the surface charge of the particles measured as zeta‐potential. One of the differences between electro‐dewatering and mechanical dewatering technologies is that electro‐dewatering actively removes ionic compounds from the sludge. In this study, dissolution and migration of organic compounds (such as shortchain fatty acids), macro metals (Na, K, Ca, Mg, Fe) and trace metals (Ni, Mn, Zn, Cr) was investigated. The migration of the metals depended on the fractionation and electrical field strength. These compounds may have both negative and positive impacts on the reuse and recycling of the sludge and removed water. Based on the experimental results of this study, electro‐dewatering process can be optimized in terms of dewatering time, desired DS content, power consumption and chemical usage.

Electrocoagulation in the treatment of industrial waters and wastewaters

Chemical coagulation is commonly used in raw water and wastewater treatment plants for the destabilisation of pollutants so that they can be removed in the subsequent separation processes. The most commonly used coagulation chemicals are aluminium and iron metal salts. Electrocoagulation technology has also been proposed for the treatment of raw waters and wastewaters. With this technology, metal cations are produced on the electrodes via electrolysis and these cations form various hydroxides in the water depending on the water pH. In addition to this main reaction, several side reactions, such as hydrogen bubble formation and the reduction of metals on cathodes, also take place in the cell. In this research, the applications of electrocoagulation were investigated in raw water treatment and wastewater applications. The surface water used in this research contained high concentrations of natural organic matter (NOM). The effect of the main parameters – current density, initial pH, electric charge per volume, temperature and electrolysis cell construction – on NOM removal were investigated. In the wastewater treatment studies, the removal of malodorous sulphides and toxic compounds from the wastewaters and debarking effluents were studied. Also, the main parameters of the treatment, such as initial pH and current density, were investigated. Aluminium electrodes were selected for the raw water treatment, whereas wastewaters and debarking effluent were treated with iron electrodes. According to results of this study, aluminium is more suitable electrode material for electrocoagulation applications because it produces Al(III) species. Metal ions and hydroxides produced by iron electrodes are less effective in the destabilisation of pollutants because iron electrodes produce more soluble and less charged Fe(II) species. However, Fe(II) can be effective in some special applications, such as sulphide removal. The resulting metal concentration is the main parameter affecting destabilisation of pollutants. Current density, treatment time, temperature and electrolysis cell construction affect the dissolution of electrodes and hence also the removal of pollutants. However, it seems that these parameters have minimal significance in the destabilization of the pollutants besides this effect (in the studied range of parameters). Initial pH and final pH have an effect on the dissolution of electrodes, but they also define what aluminium or iron species are formed in the solution and have an effect on the ζ-potential of all charged species in the solution. According to the results of this study, destabilisation mechanisms of pollutants by electrocoagulation and chemical coagulation are similar. Optimum DOC removal and low residual aluminium can be obtained simultaneously with electrocoagulation, which may be a significant benefit of electrocoagulation in surface water treatment compared to chemical coagulation. Surface water treatment with electrocoagulation can produce high quality water, which could be used as potable water or fresh water for industrial applications. In wastewater treatment applications, electrocoagulation can be used to precipitate malodorous sulphides to prevent their release into air. Technology seems to be able to remove some toxic pollutants from wastewater and could be used as pretreatment prior to treatment at a biological wastewater treatment plant. However, a thorough economic and ecological comparison of chemical coagulation and electrocoagulation is recommended, because these methods seem to be similar in pollutant destabilisation mechanisms, metal consumption and removal efficiency in most applications.

Loviisan ydinvoimalaitoksen kaapelireittien tiedonhallinnan kehittäminen paloriskitutkimusta varten

Tässä diplomityössä kehitetään Loviisan voimalaitoksen todennäköisyyspohjaisen paloriskianalyysin kaapelitietokantaa tulevaisuuden haasteita varten. Tietokannan kehittämistä varten tutustutaan todennäköisyyspohjaiseen riskianalyysiin varsin-kin paloriskianalyysin osalta. Käytännönläheisempää kehittämistä varten tutustu-taan voimalaitoksella nykyisin käytössä oleviin kaapelitietokantoihin: paloriski-tutkimusta varten laadittuun PSA-ELTIEen, kunnossapidon tiedonhallintajärjes-telmä LOMAXiin, sähkö- ja automaatiosuunnitteluyksikköjen arkistoihin sekä automaatiouudistuksen tietokantaan. Tietokannan käytännönläheisempien ominai-suuksien selvittämiseksi voimalaitoksella kokeiltiin kenttätarkastusmenetelmää, joka on ensisijainen kaapelikartoitusmenetelmä. Tietokantoihin tutustumisen perusteella vaihtoehtoisiksi tulevaisuuden tietokan-noiksi mietittiin LOMAXia, PSA-ELTIEtä tai uutta tietokantaa. Tulevaisuuden tietokantavaihtoehdoksi on päädytty ehdottamaan LOMAXia, joka vaatii vähem-män muutoksia muihin vaihtoehtoihin nähden. Tällainen laajalti käytössä oleva yhteinen tietokanta mahdollistaa sen, että tiedot ovat helpommin ja varmemmin kaikkien niitä tarvitsevien käytettävissä ja asiantuntijoiden muokattavissa, millä myös varmistetaan tietojen oikeellisuutta ja pysymistä ajan tasalla. Tulevaan LOMAX päivitykseen on ehdotettu tarpeellisia tietokenttien lisäyksiä ja kaapeli-hierarkian parantamista kaapelitietokannaksi käyttöönottamista varten.

Side peaks in Nb and NbTi point-contact spectra

Superconductor – normal metal point contacts were investigated, using different combinations of Cu, brass, Nb and NbTi. The resulting spectra contained side peaks. The currents at which these side peaks appeared, depended on the radii of the contacts. For contacts with Nb this dependence was quadratic, while for contacts with NbTi it was linear. Based on this, we argue that the side peaks in the case of the Nb contacts are due to the critical current density being exceeded. In contrast, side peaks of the NbTi contacts are caused by the self-magnetic field exceeding the lower critical field of NbTi. The NbTi contacts did not show the expected contribution from the vanishing Maxwell resistance of the superconductor, a question which remained open.

Electrochemical Treatment of Wastewaters

Electrocoagulation is a process in which wastewater is treated under electrical current. Coagulant is formed during the process through the metal anode dissolution to respective ions which react with hydroxyl ions released in cathode. These metal hydroxides form complexes with pollutant ions. Pollutants are removed among metal hydroxide precipitates. This study was concentrated on describing chemistry and device structures in which electrochemical treatment operations are based on. Studied pollutants were nitrogen compounds, sulphate, trivalent and pentavalent arsenic, heavy metals, phosphate, fluoride, chloride, and bromide. In experimental part, removal of ammonium, nitrate, and sulphate during electrochemical treatment was studied separately. Main objective of this study was to find suitable metal plate material for ammonium, nitrate, and sulphate removal, respectively. Also other parameters such as pH of solution, concentration of pollutant and sodium chloride, and current density were optimized. According to this study the most suitable material for ammonium and sulphate removal by electrochemical treatment was stainless steel. Respectively, iron was the optimum material for nitrate removal. Rise in the pH of solution at the final stage of electrochemical treatment of ammonium, nitrate, and sulphate was detected. Conductivities of solutions decreased during ammonium removal in electrochemical processes. When nitrate and sulphate were removed electrochemically conductivities of solutions increased. Concentrations of residual metals in electrochemically treated solutions were not significant. Based on this study electrochemical treatment processes are recommended to be used in treatment of industrial wastewaters. Treatment conditions should be optimized for each wastewater matrix.

Electro-Oxidation Treatment of Pulp and Paper Mill Circulating Waters and Wastewaters

Interest in water treatment by electrochemical methods has grown in recent years. Electrochemical oxidation has been applied particularly successfully to degrade different organic pollutants and disinfect drinking water. This study summarizes the effectiveness of the electrochemical oxidation technique in inactivating different primary biofilm forming paper mill bacteria as well as sulphide and organic material in pulp and paper mill wastewater in laboratory scale batch experiments. Three different electrodes, borondoped diamond (BDD), mixed metal oxide (MMO) and PbO2, were employed as anodes. The impact on inactivation efficiency of parameters such as current density and initial pH or chloride concentration of synthetic paper machine water was studied. The electrochemical behaviour of the electrodes was investigated by cyclic voltammetry with MMO, BDD and PbO2 electrodes in synthetic paper mill water as also with MMO and stainless steel electrodes with biocides. Some suggestions on the formation of different oxidants and oxidation mechanisms were also presented during the treatment. Aerobic paper mill bacteria species (Deinococcus geothermalis, Pseudoxanthomonas taiwanensis and Meiothermus silvanus) were inactivated effectively (>2 log) at MMO electrodes by current density of 50 mA/cm2 and the time taken three minutes. Increasing current density and initial chloride concentration of paper mill water increased the inactivation rate of Deinococcus geothermalis. The inactivation order of different bacteria species was Meiothermus silvanus > Pseudoxanthomonas taiwanensis > Deinococcus geothermalis. It was observed that inactivation was mainly due to the electrochemically generated chlorine/hypochlorite from chloride present in the water and also residual disinfection by chlorine/hypochlorite occurred. In real paper mill effluent treatment sulphide oxidation was effective with all the different initial concentrations (almost 100% reduction, current density 42.9 mA/cm2) and also anaerobic bacteria inactivation was observed (almost 90% reduction by chloride concentration of 164 mg/L and current density of 42.9 mA/cm2 in five minutes). Organic material removal was not as effective when comparing with other tested techniques, probably due to the relatively low treatment times. Cyclic voltammograms in synthetic paper mill water with stainless steel electrode showed that H2O2 could be degraded to radicals during the cathodic runs. This emphasises strong potential of combined electrochemical treatment with this biocide in bacteria inactivation in paper mill environments.

Microcracks and Vortices in Superconducting Thin Films

In this work, superconducting YBa₂ Cu₃O_6+x (YBCO) thin films have been studied with the experimental focus on the anisotropy of BaZrO₃ (BZO) doped YBCOthin films and the theoretical focus on modelling flux pinning by numerically solving Ginzburg- Landau equations. Also, the structural properties of undoped YBCO thin films grown on NdGaO₃ (NGO) and MgO substrates were investigated. The thin film samples were made by pulsed laser ablation on single crystal substrates. The structural properties of the thin films were characterized by X-ray diffraction and atomic force microscope measurements. The superconducting properties were investigated with a magnetometer and also with transport measurements in pulsed magnetic field up to 30 T. Flux pinning was modelled by restricting the value of the order parameter inside the columnar pinning sites and then solving the Ginzburg-Landau equations numerically with the restrictions in place. The computations were done with a parallel code on a supercomputer. The YBCO thin films were seen to develop microcracks when grown on NGO or MgO substrates. The microcrack formation was connected to the structure of the YBCO thin films in both cases. Additionally, the microcracks can be avoided by careful optimization of the deposition parameters and the film thickness. The BZO doping of the YBCO thin films was seen to decrease the effective electron mass anisotropy, which was seen by fitting the Blatter scaling to the angle dependence of the upper critical field. The Ginzburg-Landau simulations were able to reproduce the measured magnetic field dependence of the critical current density for BZO doped and undoped YBCO. The simulations showed that in addition to the large density also the large size of the BZO nanorods is a key factor behind the change in the power law behaviour between BZO doped and undoped YBCO. Additionally, the Ginzburg-Landau equations were solved for type I thin films where giant vortices were seen to appear depending on the film thickness. The simulations predicted that singly quantized vortices are stable in type I films up to quite large thicknesses and that the size of the vortices increases with decreasing film thickness, in a way that is similar to the behaviour of the interaction length of Pearl vortices.

Tuotekustannuslaskennan nykytila ja kustannusseurannan kehittäminen mallimoottoriajattelun avulla

Tutkimuksen tarkoituksena on tutkia globaalin konsernin yhden liiketoimintayksikön tuotekustannuslaskennan nykytilaa. Lisäksi tutkimuksessa selvitetään, miten tuotekohtaista kustannusseurantaa voidaan kehittää mallimoottoriajatuksen avulla. Tutkimus on toteutettu laadullisena case-tutkimuksena yhden organisaation tietojen pohjalta. Teoriaosuuden lähdeaineistot koostuvat pääosin kustannuslaskennan ja -johtamisen perusteoksista ja tieteellisistä artikkeleista. Empiriaosuuden tiedot pohjautuvat haastatteluihin, tietojärjestelmiin ja tutustumiseen organisaatioon. Tutkimuksessa selvisi, että liiketoimintayksikkö ei tällä hetkellä seuraa tuotekohtaisia kustannuksia yksittäisten tuotteiden tasolla. Kustannusseuranta tapahtuu sen sijaan suurempien kokonaisuuksien keskimääräisten kustannuksien tasolla. Tuotekustannuslaskenta on toteutettu perinteiseksi menetelmäksi luokiteltavalla laskentatavalla, jossa välilliset kustannukset kohdistetaan yleiskustannuslisäprosenttien avulla. Tutkimuksen perusteella yleiskustannuksien kohdistamisperusteissa on havaittavissa viitteitä kustannuksien vääristymisestä. Tuotetason kustannuksien seurantaan kehitettiin mallimoottoriajatukseen pohjautuva kustannusmalli, jonka avulla seurataan tarkasti valikoitujen tuotteiden kustannuksien kehittymistä sekä kustannusrakennetta. Mallin avulla voidaan lisätä tuotetason kustannustietoisuutta liiketoimintayksikössä sekä tehdä havaintoja tuotekohtaisten kustannuksien kehityssuunnasta. Mallin kustannustietona käytetään olemassa olevan kustannuslaskentajärjestelmän tietoja. Tästä johtuen mallin kustannustiedoissa on havaittavissa myös viitteitä kustannuksien vääristymisestä.

Intellectual Capital Measurement in IT industry

The goal of this research – which is to critically analyze current theories and methods of intangible assets evaluation and potentially develop and test new methodology based on the practical example(s) in the IT industry. Having this goal in mind the main research questions in this paper will be: What are advantages and disadvantages of the current practices of measurement intellectual capital or valuation of intangible assets? How to properly measure intellectual capital in IT? Resulting method exhibits a new unique approach to the IC measurement and potentially even larger field of application. Despite the fact that in this particular research, I focused my attention on IT (Software and Internet services cluster – to be exact), the logic behind the method is applicable within any industry since the method is designed to be fully compliant with measurement theory and thus can be properly scaled for any application. Building a new method is a difficult and iterative process: in the current iteration the method stands out as rather a theoretical concept rather than a business tool, however even current concept totally fulfills its purpose as a benchmarking tool for measuring intellectual capital in IT industry.

Suorituskyvyn johtaminen metalliteollisuuden yrityksessä

Tutkimuksen tavoitteena on selvittää, mitkä tekijät ovat tärkeimpiä yrityksen suorituskyvyn johtamisessa metalliteollisuusyrityksessä. Tavoitteena on myös löytää tekijät, joilla henkilökunta saadaan motivoitua ja sitoutettua yrityksen toimintaan. Lisäksi tavoitteena on saada selvitettyä kohdeyrityksen suorituskyvyn johtamisen nykytila. Tutkimus on empiirinen tutkimus, jossa käytetään kvantitatiivista eli määrällistä analyysia. Tutkimuksen teoreettisessa osuudessa tarkastellaan tutkimuksen aihetta perehtymällä aikaisempiin tutkimuksiin ja kirjallisuuteen. Kohdeyrityksen nykytilan kartoituksessa käytettiin valmista SUMO-kartoitusta, joka mittaa työmotivaation ja toiminnan tehostumisen taustalla vaikuttavia tekijöitä. Suorituskyvyn menestyksellinen johtaminen metalliteollisuusyrityksessä vaatii toimivaa suorituskyvyn mittaamisjärjestelmää, jota analysoimalla pystytään tekemään päätöksiä tulevaisuuden toimenpiteistä. Suorituskyvyn mittaaminen pitäisi lisäksi kytkeä palkitsemiseen. Työntekijöiden työmotivaatioon ja sitoutumiseen voidaan vaikuttaa monella tapaa. Työmotivaatioon ja sitoutumiseen vaikuttavat työntekijöiden vaikutus- ja koulutusmahdollisuudet sekä palkitseminen, viestintä ja tavoitteet. Näiden tekijöiden luomisessa johtaminen on avainasemassa.

Pharmacométrie de la ropivacaïne suivant l’anesthésie locorégionale chez les patients orthopédiques : caractérisation de l’intensité et de la durée du bloc sensitif

Introduction & Objectifs : Pour assurer l’analgésie postopératoire, l’anesthésiste dispose, en plus des différentes classes de médicaments administrés par voie orale ou intraveineuse, de diverses techniques pour bloquer l’influx nerveux douloureux en administrant les anesthésiques locaux (AL) de manière centrale ou périphérique. La ropivacaïne (ROP), un AL à longue durée d’action, est un médicament de première intention partout dans le monde, en raison de sa grande efficacité et de son faible risque de toxicité. Contrairement à certains pays, la ROP n'est toujours pas indiquée au Canada pour la rachianesthésie (bloc central) en raison d'un manque de données probantes. Jusqu'à présent, les efforts de recherche ont essentiellement porté sur la sécurité ainsi que sur la durée d’action du médicament lorsqu’administré par voie spinale. De plus, les doses optimales de ROP pour l’anesthésie régionale périphérique ne sont pas encore précisément connues. La posologie devrait être adaptée au site d’administration ainsi qu’à l’intensité et la durée du stimulus produit par la chirurgie. Ultimement, cela permettrait aux cliniciens d’identifier le régime optimal en fonction des facteurs démographiques qui pourraient affecter la pharmacocinétique (PK) et la pharmacodynamie (PD) de l’AL (objectif global de ces travaux). Validation de la Méthode Analytique Manuscrit 1 : Une méthode analytique spécifique et sensible permettant de déterminer les concentrations plasmatiques de ROP a d’abord été optimisée et validée. Validation du Biomarqueur Manuscrit 2 : Nous avons ensuite mis au point et évalué la fiabilité d’une méthode quantitative basée sur la mesure du seuil de perception sensorielle (CPT) chez le volontaire sain. Ce test nécessite l’application d’un courant électrique transcutané qui augmente graduellement et qui, selon la fréquence choisie, est capable de stimuler spécifiquement les fibres nerveuses impliquées dans le cheminement de l’influx nerveux douloureux. Les résultats obtenus chez les volontaires sains indiquent que la mesure CPT est fiable, reproductible et permet de suivre l’évolution temporelle du bloc sensitif. Études cliniques Manuscrit 3 : Nous avons ensuite caractérisé, pendant plus de 72 h, l’absorption systémique de la ROP lorsqu’administrée pour un bloc du nerf fémoral chez 19 patients subissant une chirurgie du genou. Le modèle PK populationnel utilisé pour analyser nos résultats comporte une absorption biphasique durant laquelle une fraction de la dose administrée pénètre rapidement (temps d’absorption moyen : 27 min, IC % 19 – 38 min) dans le flux sanguin systémique pendant que l’autre partie, en provenance du site de dépôt, est redistribuée beaucoup plus lentement (demi-vie (T1/2) : 2.6 h, IC % 1.6 – 4.3 h) vers la circulation systémique. Une relation statistiquement significative entre l’âge de nos patients et la redistribution de l’AL suggère que la perméabilité tissulaire est augmentée avec l’âge. Manuscrit 4 : Une analyse PK-PD du comportement sensitif du bloc fémoral (CPT) a été effectuée. Le modèle développé a estimé à 20.2 ± 10.1 mg la quantité de ROP nécessaire au site d’action pour produire 90 % de l’effet maximal (AE90). À 2 X la AE90, le modèle prédit un début d’action de 23.4 ± 12.5 min et une durée de 22.9 ± 5.3 h. Il s’agit de la première étude ayant caractérisé le comportement sensitif d’un bloc nerveux périphérique. Manuscrit 5 : La troisième et dernière étude clinique a été conduite chez les patients qui devaient subir une chirurgie du genou sous rachianesthésie. Tout comme pour le bloc du nerf fémoral, le modèle PK le plus approprié pour nos données suggère que l’absorption systémique de la ROP à partir du liquide céphalo-rachidien est biphasique; c.à.d. une phase initiale (T1/2 : 49 min, IC %: 24 – 77 min) suivie (délai: 18 ± 2 min) d'une phase légèrement plus lente (T1/2 : 66 min, IC %: 36 – 97 min). L’effet maximal a été observé beaucoup plus rapidement, soit aux environs de 12.6 ± 4.9 min, avant de revenir aux valeurs de base 210 ± 55 min suivant l’administration de l’agent. Ces données ont permis d’estimer une AE50 de 7.3 ± 2.3 mg pour l'administration spinale. Conclusion : En somme, ces modèles peuvent être utilisés pour prédire l’évolution temporelle du bloc sensitif de l’anesthésie rachidienne et périphérique (fémorale), et par conséquent, optimiser l’utilisation clinique de la ROP en fonction des besoins des cliniciens, notamment en ce qui a trait à l’âge du patient.