Designing Digital Filters for Servo Systems

The aim of this work was to select an appropriate digital filter for a servo application and to filter the noise from the measurement devices. Low pass filter attenuates the high frequency noise beyond the specified cut-off frequency. Digital lowpass filters in both IIR and FIR responses were designed and experimentally compared to understand their characteristics from the corresponding step responses of the system. Kaiser Windowing and Equiripple methods were selected for FIR response, whereas Butterworth, Chebyshev, InverseChebyshev and Elliptic methods were designed for IIR case. Limitations in digital filter design for a servo system were analysed. Especially the dynamic influences of each designed filter on the control stabilityof the electrical servo drive were observed. The criterion for the selection ofparameters in designing digital filters for servo systems was studied. Control system dynamics was given significant importance and the use of FIR and IIR responses in different situations were compared to justify the selection of suitableresponse in each case. The software used in the filter design was MatLab/Simulink® and dSPACE's DSP application. A speed controlled Permanent Magnet Linear synchronous Motor was used in the experimental work.

Implementing theLean Manufacturing System

Tuottavuuden ja tehokkuuden parantaminen on keskeisimpiä menestystekijöitä glo-baaleilla markkinoilla. Yksi kehittämisen toimintamalli on lean manufacturing -ajattelutapa, joka perustuu imuohjaukseen. Sen lähtökohtana on asiakasarvo ja keskit-tyminen arvoa lisäävien toimintojen maksimointiin. Tutkimuksen tavoitteena oli parantaa Strömfors Electric Oy:n materiaalivirtauksia yhdellä tuotantolinjalla. Projektin oli tarkoitus olla pilotti lean-implementointiin koko tehtaalla. Projektissa otettiin käyttöön kanban-imuohjausjärjestelmä, jota varten teh-tiin analyysejä ja laskelmia arvovirtoihin, varastoihin ja ohjaukseen. Lean-ajattelutapaan ja -työkaluihin perustuvaa kirjallisuutta käytettiin pohjatietona pilotti-projektissa sekätulevien kehitysprojektien suunnittelussa. Pilottiprojektin tuloksena materiaalinohjaus tehostui ja keskeneräisen tuotannon va-rasto tasoittui käyttötarpeen mukaiseksi. Työntekijät ja työnjohtajat tutustuivat leanin perusteisiin osallistuessaan pilottiprojektiin. Pidemmän aikavälin suunnitelmissa ontoimitusvarmuuden ja laadun parantuminen ensin pilottiprojektia koskevalla linjalla ja myöhemmin koko tehtaalla imuohjauksen kokonaisvaltaisen käyttöönoton myötä.

Field Sales Management Control: Towards a Multi-Level Theory

The purpose of this dissertation is to increase the understanding and knowledge of field sales management control systems (i.e. sales managers monitoring, directing, evaluating and rewarding activities) and their potential consequences on salespeople. This topic is important because research conducted in the past has indicated that the choice of control system type can on the other hand have desirable consequences, such as high levels of motivation and performance, and on the other hand leadto harmful unintended consequences, such as opportunistic or unethical behaviors. Despite the fact that marketing and sales management control systems have been under rigorous research for over two decades, it still is at a very early stage of development, and several inconsistencies can be found in the research results. This dissertation argues that these inconsistencies are mainly derived from misspecification of the level of analysis in the past research. These different levels of analysis (i.e. strategic, tactical, and operational levels) involve very different decision-making situations regarding the control and motivation of sales force, which should be taken into consideration when conceptualizing the control. Moreover, the study of salesperson consequences of a field sales management control system is actually a cross-level phenomenon, which means that at least two levels of analysis are simultaneously involved. The results of this dissertation confirm the need to re-conceptualize the field sales management control system concept. It provides empirical evidence for the assertion that control should be conceptualized with more details atthe tactical/operational level of analysis than at the strategic levelof analysis. Moreover, the results show that some controls are more efficiently communicated to field salespeople than others. It is proposed that this difference is due to different purposes of control; some controls aredesigned for influencing salespersons' behavior (aim at motivating) whereas some controls are designed to aid decision-making (aim at providing information). According to the empirical results of this dissertation, the both types of controls have an impact to the sales force, but this impactis not as strong as expected. The results obtained in this dissertation shed some light to the nature of field sales management control systems, and their consequences on salespeopl

Converter-flux-based current control of voltage source PWM rectifiers - analysis and implementation

Pulsewidth-modulated (PWM) rectifier technology is increasingly used in industrial applications like variable-speed motor drives, since it offers several desired features such as sinusoidal input currents, controllable power factor, bidirectional power flow and high quality DC output voltage. To achieve these features,however, an effective control system with fast and accurate current and DC voltage responses is required. From various control strategies proposed to meet these control objectives, in most cases the commonly known principle of the synchronous-frame current vector control along with some space-vector PWM scheme have been applied. Recently, however, new control approaches analogous to the well-established direct torque control (DTC) method for electrical machines have also emerged to implement a high-performance PWM rectifier. In this thesis the concepts of classical synchronous-frame current control and DTC-based PWM rectifier control are combined and a new converter-flux-based current control (CFCC) scheme is introduced. To achieve sufficient dynamic performance and to ensure a stable operation, the proposed control system is thoroughly analysed and simple rules for the controller design are suggested. Special attention is paid to the estimationof the converter flux, which is the key element of converter-flux-based control. Discrete-time implementation is also discussed. Line-voltage-sensorless reactive reactive power control methods for the L- and LCL-type line filters are presented. For the L-filter an open-loop control law for the d-axis current referenceis proposed. In the case of the LCL-filter the combined open-loop control and feedback control is proposed. The influence of the erroneous filter parameter estimates on the accuracy of the developed control schemes is also discussed. A newzero vector selection rule for suppressing the zero-sequence current in parallel-connected PWM rectifiers is proposed. With this method a truly standalone and independent control of the converter units is allowed and traditional transformer isolation and synchronised-control-based solutions are avoided. The implementation requires only one additional current sensor. The proposed schemes are evaluated by the simulations and laboratory experiments. A satisfactory performance and good agreement between the theory and practice are demonstrated.

Production Control Principles in Printed Wiring Board Fabrication

Työn tavoitteena oli kuvata piirilevyvalmistaja Aspocomp Oy:n Espoon tehtaan tämän hetkinen tuotannonohjausperiaate ja tunnistaa siinä esiintyvät puutteet sekä kehittää vaihtoehtoinen tuotannonohjausperiaate piirilevyvalmistukseen. Vaihtoehtoisen ohjausperiaatteen lähtökohtana oli tuotannonohjauksen sopeuttaminen vaativaan ja jatkuvasti muuttuvaan liiketoimintaympäristöön. Työn teoreettinen osa keskittyi tuotannonohjauksen eri lähestymistapoihin. Kirjallisuuskatsauksessa esitetään eri tuotannonohjausperiaatteiden keskeiset sisällöt, jotka muodostavat rungon toimivalle tuotannonohjauskäytännölle. Työn kokeellinen osa keskittyi Espoon piirilevytehtaan tuotannonohjausperiaatteen selvittämiseen. Espoon piirilevytehtaan nykyisessä tuotannonohjausperiaatteessa havaittujen ongelmakohtien ja liiketoimintaympäristön vaatimusten perusteella kehitettiin vaihtoehtoinen tuotannonohjaustapa. Vaihtoehtoisen tuotannonohjaustavan päämääränä oli läpimenoajan lyhentäminen sekä tuotannon parempi hallittavuus. Vaihtoehtoinen toimintamalli tavoitteiden saavuttamiseksi perustuu pullonkaulateoriaan, jossa keskeisin muutos nykyiseen toimintamalliin oli puolivalmisteiden varastointi toimitusajan lyhentämiseksi sekä tuotantovolyymin heilahdusten vaikutusten vähentämiseksi. Työn kokeellisessa osassa ilmeni, että kysynnän muutokset ja kapasiteetin suunnittelun puute aiheuttivat ongelmia piirilevytehtaan tuotannonohjauksessa.

Digitalización del sistema de control de nivel en calentadores y tanques de drenaje de una Central Nuclear

Contexto Una central nuclear, al igual que cualquier otro tipo de central generadora de energía eléctrica, mediante turbinas de vapor, está basada en un proceso termodinámico. El rendimiento de las mismas es función del salto entálpico del vapor, para mejorarlo las centrales están constituidas por un ciclo compound formado por turbina de alta presión y turbinas de baja presión, y un ciclo regenerativo consistente en calentar el agua de alimentación antes de su introducción a los generadores de vapor. Un ciclo regenerativo está basado en etapas de calentadores o cambiadores de calor para aprovechar al máximo la energía térmica del vapor, este proyecto está basado en la mejora y optimización del proceso de control de estos para contribuir a mejorar el rendimiento de la central. Objetivo Implementar un sistema de control que nos permita modernizar los clásicos sistemas basados en controles locales y comunicaciones analógicas. Mejorar el rendimiento del ciclo regenerativo de la central, aprovechando las mejoras tecnológicas que ofrece el mercado, tanto en el hardware como en el software de los sistemas de instrumentación y control. Optimizar el rendimiento de los lazos de control de cada uno de los elementos del ciclo regenerativo mediante estrategias de control. Procedimiento Desarrollo de un sistema de control actualizado considerando, como premisa principal, la fiabilidad del sistema, el análisis de fallos y la jerarquización del riesgo. Análisis y cálculo de los lazos de control considerando las premisas establecidas. Configuración de los lazos mediante estrategias de control que nos permitan optimizar y minimizar los efectos del fallo. Para ello se han utilizado parámetros y datos extraídos de la Central Nuclear de Ascó. Conclusiones Se ha modernizado y optimizado el sistema de control mejorando el rendimiento del ciclo regenerativo. Se ha conseguido un sistema más fiable, reduciendo el riesgo del fallo y disminuyendo los efectos de los mismos. El coste de un proyecto de estas características es inferior al de un sistema convencional y ofrece más posibilidades. Es un sistema abierto que permite utilizar e interconectar equipos de diferentes fabricantes, lo que favorece tanto el mantenimiento como las posibles ampliaciones futuras del sistema.

System Investigation for Hybrid Electric Vehicle

A hybrid electric vehicle is a fast-growing concept in the field of vehicle industry. Nowadays two global problems make manufactures to develop such systems. These problems are: the growing cost of a fuel and environmental pollution. Also development of controlled electric drive with high control accuracy and reliability allows improving of vehicle drive characteristics. The objective of this Diploma Thesis is to investigate the possibilities of electrical drive application for new principle of parallel hybrid vehicle system. Electric motor calculations, selection of most suitable control system and other calculations are needed. This work is not final work for such topic. Further investigation with more precise calculations, modeling, measurements and cost calculations are needed to answer the question if such system is efficient.

Stability-indicating methods for quantitative determination of zidovudine and stavudine in capsules

Zidovudine (AZT) and stavudine (D4T) are nucleoside reverse transcriptase inhibitors extensively used in human immunodeficiency virus (HIV) infected patients. In order to evaluate the quality of these drugs, two stability indicating HPLC methods were developed. The validated methods were applied in quantitative determination of AZT, D4T and their induced degradation products in capsule preparations. The stability studies were conducted at controlled temperature and relative humidity conditions based on the International Conference on Harmonization stability studies protocol for Zone IV areas. Easy sample preparation and low-cost make these methods especially useful for quality control and stability studies of AZT and D4T in drug products.

The effects of real time control of welding parameters on weld quality in plasma arc keyhole welding

Joints intended for welding frequently show variations in geometry and position, for which it is unfortunately not possible to apply a single set of operating parameters to ensure constant quality. The cause of this difficulty lies in a number of factors, including inaccurate joint preparation and joint fit up, tack welds, as well as thermal distortion of the workpiece. In plasma arc keyhole welding of butt joints, deviations in the gap width may cause weld defects such as an incomplete weld bead, excessive penetration and burn through. Manual adjustment of welding parameters to compensate for variations in the gap width is very difficult, and unsatisfactory weld quality is often obtained. In this study a control system for plasma arc keyhole welding has been developed and used to study the effects of the real time control of welding parameters on gap tolerance during welding of austenitic stainless steel AISI 304L. The welding tests demonstrated the beneficial effect of real time control on weld quality. Compared with welding using constant parameters, the maximum tolerable gap width with an acceptable weld quality was 47% higher when using the real time controlled parameters for a plate thickness of 5 mm. In addition, burn through occurred with significantly larger gap widths when parameters were controlled in real time. Increased gap tolerance enables joints to be prepared and fit up less accurately, saving time and preparation costs for welding. In addition to the control system, a novel technique for back face monitoring is described in this study. The test results showed that the technique could be successfully applied for penetration monitoring when welding non magnetic materials. The results also imply that it is possible to measure the dimensions of the plasma efflux or weld root, and use this information in a feedback control system and, thus, maintain the required weld quality.

Estudi i primera fase per la implementació del FOFB al Sincrotró ALBA

Aquest treball és la culminació de les pràctiques realitzades al sincrotró ALBA. Situat a Cerdanyola del Vallès, ALBA és un accelerador de 3a generació que permet emmagatzemar un feix d'electrons confinat de fins a 400 mA a 3GeV d'energia, amb l'objectiu d'obtenir llum a partir dels girs provocats al feix. Els sincrotrons moderns com el d'ALBA, el que pretenen és aconseguir un major control i estabilitat de la llum. Per aconseguir-ho, cal que el feix d'electrons que creen la llum estigui controlat al màxim i la seva òrbita sigui estable. Amb aquest objectiu els sincrotrons estant implementant sistemes de Fast Orbit FeedBack (FOFB) o sistemes realimentats de correcció ràpida de l'òrbita, per realitzar correccions d'almenys 100Hz que estabilitzin el feix d'electrons amb menys d'un 10% de l'amplada del feix (5-10μm). El treball exposa el desenvolupament d'una part del sistema de correcció ràpida de l'òrbita dels electrons (FOFB) que s'està duent a terme al sincrotró ALBA. Concretament, s’han revisat els estudis previs realitzats durant la fase de disseny del sincrotró, s’han recalculat funcions de transferència i retards de tots els elements involucrats al sistema. També s’han realitzat simulacions per confirmar la viabilitat del sistema amb les noves dades i finalment s’ha desenvolupat part de la unitat de control determinant el Hardware i s'ha adquirit dades que permetran analitzar el soroll de l'òrbita que en futurs treballs determinaran millor l'algorisme de la unitat de control.

Improving Cross Direction Basis Weight Profile in a Fourdrinier Paper Machine

The purpose of this study was to improve PM7’s basis weight CD profile in Stora Enso’s Berghuizer mill and to search mechanical defects which affect to the formation of the basis weight CD profile. In the theoretical part PM7’s structure was presented and the formation of the basis weight and caliper CD profiles was examined as well as disturbances which are affecting to the formation. The function of the control system was scrutinised for the side of CD profiles as well as the formation of the measured CD profiles. Tuning of the control system was examined through the response model and filtering. Specification of the response model and filtering was explained and how to determine 2sigma statistical number. In the end of the theoretical part ATPA hardware and a new profile browser were introduced. In the experimental part focus was in the beginning to search and remove mechanical defects which are affecting to CD profiles. The next step was to verify the reliability of the online measurements, to study the stability of the basis weight CD profile and to find out so called fingerprint, a basis weight CD profile which is unique for each paper machine. New response model and filtering value for basis weight CD profile was determined by bump tests. After a follow up period the affect of the new response model and filtering was analysed.

Simulating the performance of paper machine control

The topic of this thesis is the simulation of a combination of several control and data assimilation methods, meant to be used for controlling the quality of paper in a paper machine. Paper making is a very complex process and the information obtained from the web is sparse. A paper web scanner can only measure a zig zag path on the web. An assimilation method is needed to process estimates for Machine Direction (MD) and Cross Direction (CD) profiles of the web. Quality control is based on these measurements. There is an increasing need for intelligent methods to assist in data assimilation. The target of this thesis is to study how such intelligent assimilation methods are affecting paper web quality. This work is based on a paper web simulator, which has been developed in the TEKES funded MASI NoTes project. The simulator is a valuable tool in comparing different assimilation methods. The thesis contains the comparison of four different assimilation methods. These data assimilation methods are a first order Bayesian model estimator, an ARMA model based on a higher order Bayesian estimator, a Fourier transform based Kalman filter estimator and a simple block estimator. The last one can be considered to be close to current operational methods. From these methods Bayesian, ARMA and Kalman all seem to have advantages over the commercial one. The Kalman and ARMA estimators seems to be best in overall performance.

Spectrophotometric study of iron oxidation in the iron(II)/thiocyanate/acetone system and some analytical applications

The possibility of using thiocyanate to determine iron(II) and/or iron(III) in water-acetone mixture has been re-examined as part of a systematic and comparative study involving metallic complexes of pseudohalide ligands. Some parameters that affect the complete oxidation of the ferrous cations, their subsequent complexation and the system stability have been studied to optimize the experimental conditions. Our results show the viability and potentiality of this simply methodology as an alternative analytical procedure to determine iron cations with high sensitivity, precision and accuracy. Studies on the calibration, stability, precision, and effect of various different ions have been carried out by using absorbance values measured at 480 nm. The analytical curve for the total iron determination obeys Beer's law (r = 0.9993), showing a higher sensitivity (molar absorptivity of 2.10x10(4) L cm-1 mol-1) when compared with other traditional systems (ligands) or even with the "similar" azide ion [1.53x10(4) L cm-1 mol-1, for iron-III/azide complexes, in 70% (v/v) tetrahydrofuran/water, at 396 nm]. Under such optimized experimental conditions, it is possible to determine iron in the concentration range from 0.5 to 2 ppm (15-65% T for older equipments, quartz cells of 1.00 cm). Analytical applications have been tested for some different materials (iron ores), also including pharmaceutical products for anemia, and results were compared with atomic absorption determinations. Very good agreement was obtained with these two different techniques, showing the potential of the present experimental conditions for the total iron spectrophotometric determinations (errors < 5%). The possibility of iron speciation was made evident by using another specific and auxiliary method for iron(II) or (III).

Modeling and Control of the Power Conversion Unit in a Solid Oxide Fuel Cell Environment

In this doctoral thesis, a power conversion unit for a 10 kWsolid oxide fuel cell is modeled, and a suitable control system is designed. The need for research was identified based on an observation that there was no information available about the characteristics of the solid oxide fuel cell from the perspective of power electronics and the control system, and suitable control methods had not previously been studied in the literature. In addition, because of the digital implementation of the control system, the inherent characteristics of the digital system had to be taken into account in the characteristics of the solid oxide fuel cell (SOFC). The characteristics of the solid oxide fuel cell as well the methods for the modeling and control of the DC/DC converter and the grid converter are studied by a literature survey. Based on the survey, the characteristics of the SOFC as an electrical power source are identified, and a solution to the interfacing of the SOFC in distributed generation is proposed. A mathematical model of the power conversion unit is provided, and the control design for the DC/DC converter and the grid converter is made based on the proposed interfacing solution. The limit cycling phenomenon is identified as a source of low-frequency current ripple, which is found to be insignificant when connected to a grid-tied converter. A method to mitigate a second harmonic originating from the grid interface is proposed, and practical considerations of the operation with the solid oxide fuel cell plant are presented. At the theoretical level, the thesis discusses and summarizes the methods to successfully derive a model for a DC/DC converter, a grid converter, and a power conversion unit. The results of this doctoral thesis can also be used in other applications, and the models and methods can be adopted to similar applications such as photovoltaic systems. When comparing the results with the objectives of the doctoral thesis, we may conclude that the objectives set for the work are met. In this doctoral thesis, theoretical and practical guidelines are presented for the successful control design to connect a SOFC-based distributed generation plant to the utility grid.

One chip solution for low-cost active magnetic bearing system

In this work the implementation of the active magnetic bearing control system in a single FPGA is studied. Requirements for the full magnetic bearing control system are reviewed. Different control methods for active magnetic bearings are described shortly. Flux and the current base controllers are implemented in a FPGA. Suitability of the con-trollers for a low-cost magnetic bearing application is studied. Floating-point arithmetic’s are used in the controllers to ease designing burden and improve calculation precision. Per-formance of the flux controller is verified with simulations.