Estudo da reciclagem do banho de caleiro de pele caprina

Mestrado em Engenharia Química

Selecção do melhor descolorante para a eliminação da cor residual num efluente têxtil

Mestrado em Engenharia Química

Evaluating the efficiency of a vegetal coagulant in the treatment of industrial effluents

The present work aims at evaluating the efficiency of an organic polymer from vegetal source used as coagulant for treating different types of industrial effluents. This coagulant (Flox-QT) is obtained from the Black Acacia (Acacia mearnsii). The effluents studied were produced in petrochemical, leather, cork stoppers, metalworking, olive oil, glue, paint (printing), textile and paper industries. The parameters analyzed in the effluents before and after treatment were selected according to the type of wastewater and included pH, conductivity, apparent colour, turbidity, total suspended solids (TSS), chemical oxygen demand (COD) and some metals. The coagulant proved to be efficient for almost all effluents tested. The best results were obtained for the paper industry wastewater, with 91% removal of chemical oxygen demand and 95% of total suspended solids removal. The estimated cost of this treatment would be only 0.24 Euro per cubic meter of treated effluent, only regarding the price of the coagulant and the required dosage. The use of this coagulant is also adequate for the valorisation of the sludge obtained, which in this case could be recycled for paper production.

Estudo da tratabilidade laboratorial e optimização experimental do tratamento de águas residuais de indústrias lácteas

O presente trabalho experimental teve como objectivos estudar a tratabilidade dum efluente lácteo utilizando a técnica de coagulação/floculação e avaliar a possibilidade de utilização do carvão activado granulado (CAG) Aquasorb 2000 como adsorvente para a remoção de compostos orgânicos presentes nos efluentes lácteos pré–tratados por coagulação/floculação, funcionando como um tratamento de polimento. No estudo da tratabilidade do efluente por coagulação/floculação investigou-se a influência de determinadas variáveis como o tipo e dose de coagulante e pH, a fim de encontrar as melhores condições operatórias. A utilização da referida técnica visou a redução do valor de concentração de alguns parâmetros: carência química de oxigénio (CQO); fósforo total e turvação, tendo sido utilizados efluentes desta indústria recolhidos em diferentes datas e após tratamento biológico, designados por A, B, C e D apresentando características diferentes. Sendo que o efluente A apresentava valores de CQO, fósforo total e turvação de 500 mg O2/L;32 mg P/L e 40 NTU respectivamente, o efluente B 1400 mg O2/L; 120 mg P/L e 80 NTU respectivamente, o efluente C 12300 mg O2/L; 87 mg P/L e 350 NTU respectivamente e o efluente D 340 mg O2/L; 33 mg P/L e 42 NTU respectivamente. Os coagulantes estudados foram hidróxido de cálcio (HC), sulfato de alumínio (SA) e tricloreto de ferro (TF). Verificou-se que o coagulante com maior eficácia nos efluentes estudados foi o TF. As maiores remoções de CQO, fósforo total e turvação, 89%, 99,9% e 99%, respectivamente, foram obtidas para o efluente C, com uma dosagem de TF de 4 g/L e com um pH entre 6 e 7. Entre os efluentes estudados este era o que apresentava valores iniciais mais elevados para qualquer um destes parâmetros. As melhores percentagens de remoção obtidas com o HC, para a CQO, fósforo total e turvação foram de 59%, 99% e 91%, respectivamente, com uma dosagem de HC de 1 g/L e com um pH entre 10 e 11,5 foram conseguidas no tratamento do efluente D, com o qual se alcançaram também as melhores remoções de CQO, fósforo total e turvação de 65%, 99% e 87%, respectivamente, quando se utilizou o coagulante SA, com uma dosagem de 2 g/L e com um pH entre 7 e 7,5. Relativamente ao volume de lamas produzido neste processo pela utilização dos diferentes coagulantes no tratamento dos efluentes referidos concluiu-se que o coagulante que gera menor volume de lamas é o HC, sendo o SA aquele que origina um maior volume. Submeteu-se posteriormente o efluente D, pré-tratado por coagulação/floculação, a um processo de adsorção em batch utilizando o CAG Aquasorb 2000, onde se conseguiu uma remoção de CQO de 48%, alcançando para este parâmetro o valor de 63 mg O2/L, nas condições operatórias que correspondem a uma massa de CAG de 12,5 g/L e um tempo de contacto de 3 horas. Quanto aos custos associados com os coagulantes, o que menores custos apresenta é o HC (150 €/ton), seguido pelo TF (250 €/ton) e por ultimo o SA (340 €/ton). Sendo que o efluente quando tratado com TF e SA é necessário uma correcção do pH do meio para que estes coagulantes actuem eficazmente, em que essa correcção de pH é realizada com hidróxido de sódio (540 €/ton). Realizaram-se ainda estudos de equilíbrio de adsorção com o carvão activado referido e o azul-de-metileno usando diferentes concentrações deste (50 mg/L; 100 mg/L e 200 mg/L) e diferentes massas de CAG (0,1g; 0,2g; 0,3g; 0,4g e 0,5g). A temperatura a que se realizaram estes ensaios foi de 28,7ºC e o volume de azul-de-metileno foi de 200 mL. Verificou-se que os melhores resultados obtidos foram para uma concentração de adsorvato de 100 mg/L. Ajustaram-se os modelos de Langmuir e Freundlich às isotérmicas obtidas tendo correlações mais elevadas para a concentração de 100 mg/L de corante (azul de metileno), sendo o modelo de Freundlich aquele que melhor se ajustou apresentando uma correlação quadrática de 0,9744 e os seguintes parâmetros Kf = 6,59 e n = 5,33, enquanto que o de Langmuir apresentou uma correlação quadrática de 0,9583 e os seguintes parâmetros qmáx = 83,3 mg/g de adsorvente e K = 20 L/mg de adsorvato.. Verificou-se que a capacidade de adsorção promovida pelo CAG, em relação ao azul-demetileno, obtida experimentalmente, 83,3 mg/g, é muito inferior à capacidade de adsorção teoricamente prevista pela ficha técnica deste carvão, 280 mg/g a uma temperatura de 25ºC, o que pode indiciar que o carvão utilizado não estaria nas melhores condições.

Ecotoxicity tests using the green algae chlorella vulgaris — a useful tool in hazardous effluents management

The treatment efficiency of laboratory wastewaters was evaluated and ecotoxicity tests with Chlorella vulgaris were performed on them to assess the safety of their environmental discharge. For chemical oxygen demand wastewaters, chromium (VI), mercury (II) and silver were efficiently removedby chemical treatments.Areduction of ecotoxicitywas achieved; nevertheless, an EC50 (effective concentration that causes a 50% inhibition in the algae growth) of 1.5% (v/v) indicated still high level of ecotoxicity. For chloride determination wastewaters, an efficient reduction of chromium and silver was achieved after treatment. Regarding the reduction of ecotoxicity observed, EC50 increased from 0.059% to 0.5%, only a 0.02% concentration in the aquatic environment would guarantee no effects. Wastewaters containing phenanthroline/iron (II) complex were treated by chemical oxidation. Treatmentwas satisfactory concerning chemical parameters, although an increase in ecotoxicitywas observed (EC50 reduced from 0.31% to 0.21%). The wastes from the kinetic study of persulphate and iodide reaction were treated with sodium bisulphite until colour was removed. Although they did not reveal significant ecotoxicity, only over 1% of the untreated waste produced observable effects over algae. Therefore, ecotoxicity tests could be considered a useful tool not only in laboratory effluents treatment, as shown, but also in hazardous wastewaters management.

MBR activated sludge filterability characterization in cross flow filtration

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para a obtenção do grau de Mestre em Engenharia do Ambiente, perfil Sanitária

Impacto Ambiental do Processo de Tingimento de uma Indústria de Curtumes e Avaliação do Desempenho da ETAR

Um dos objetivos desta dissertação de mestrado foi avaliar o impacto ambiental do processo de tingimento usado na indústria de curtumes, em termos de volume de efluente produzido e sua carga poluente. Pretendeu-se também encontrar alternativas ao nível do processo de tingimento que levem a uma melhoria na qualidade do efluente produzido. Outro objetivo deste trabalho foi avaliar o funcionamento da ETAR existente na empresa JR Fontes, no que diz respeito aos parâmetros em estudo (carência química de oxigénio - CQO, pH, crómio e teor de sólidos suspensos totais - SST), propondo alterações que permitam respeitar os valores de emissão exigidos na licença de descarga da empresa. Verificou-se que o processo de tingimento aplicado pela empresa JR Fontes é muito poluente, em termos de carga orgânica e matéria em suspensão. Este facto é comprovado pelos resultados obtidos para os três processos estudados: Montana, Galáctico e Navak. Todos os processos apresentam um efluente com pH ácido (aproximado a 3) e valores de CQO superiores a 3550 mg O2/L, sendo o processo Navak aquele que apresenta o valor mais alto para o banho composto, 8362 mg O2/L. Relativamente ao teor de crómio, o banho de recurtume com concentração mais elevada de crómio total é o banho 1 do processo Navak, com 2297 mg/L, sendo que a concentração destes banhos é sempre elevada, igual ou superior a 746 mg/L. No que diz respeito à matéria em suspensão, o processo Navak é novamente o mais poluente, com um valor de 3842 mg SST/L, não sendo obtidos nos outros processos, valores inferiores a 1205 mg SST/L. Na realização de um processo alternativo de tingimento verificou-se que é possível diminuir a carga orgânica do efluente originado. A aplicação de recurtumes sintéticos deu origem a efluentes menos poluentes. O melhor valor obtido para a CQO foi de 1113 mg O2/L, sendo obtidos valores não superiores a 7185 mg O2/L para processos de características semelhantes aos aplicados nesta indústria. Relativamente à ETAR, apesar das restrições ao funcionamento que esta apresenta, no geral pode ser considerada eficiente, embora não consiga atingir o objetivo pretendido de remoção para a CQO, ou seja o valor de 1100 mg O2/L. Nos restantes parâmetros é cumprido o limite de emissão (350 mg SST/L, pH entre 6 e 9 e 2 mg Cr/L para o crómio total): os SST apresentam o valor de 98 mg SST/L, o crómio total de 1,2 mg Cr/L e o pH encontra-se entre 8 e 9. São aqui feitas duas abordagens para solucionar os problemas existentes na ETAR. A primeira considera um ajuste no tratamento e equipamentos existentes, através da reconstrução do tanque de equalização, da substituição do coagulante por sulfato ferroso e da reconstrução do sedimentador, assim como a substituição das tubagens por umas de maior diâmetro, solucionando assim problemas de manutenção de toda a instalação e do incumprimento da legislação. A outra abordagem implica a substituição do sistema de afinação existente, os filtros de areia e carvão ativados, por um sistema de membranas de ultrafiltração ou por dois filtros de carvão ativado. Para tratar um efluente com um valor de CQO de 3000 mg O2/L com o carvão estudado, seriam necessários 132 kg de carvão por coluna, aproveitando-se os equipamentos existentes. No caso das membranas filtrantes, estas são eficazes, reduzindo a CQO em cerca de 70%. Ao contrário do carvão, a aplicação deste sistema implicaria a aquisição de novos equipamentos. Futuramente propõe-se a avaliação dos vários tipos de reagentes usados no tingimento de couro de forma a aplicar no tratamento aqueles que produzam as características desejadas no produto final e a que apresentem um menor resultado de CQO. Propõe-se também o estudo de viabilidade da remoção de crómio dos banhos de recurtume e consequente avaliação da aplicabilidade de um tratamento biológico em substituição ou como complemento do tratamento existente.

Minimização do impacto ambiental do processo de curtume de pele de bovino

O presente trabalho teve como objectivo a minimização do impacto ambiental do processo de curtume da pele de bovino. A indústria de curtumes transforma a pele, material putrescível, em couro, material nobre, termicamente estável e imputrescível. A transformação da pele em couro origina uma carga poluente apreciável quer quanto a efluentes líquidos quer quanto a resíduos sólidos. O fluxo produtivo da indústria de curtumes pode dividir-se em quatro sectores: ribeira, curtume, tinturaria e acabamento, sendo que os três primeiros geram efluentes líquidos com elevada carga poluente. Neste trabalho, foram avaliadas as fases do processo que geram efluentes líquidos: molho, caleiro, curtume e tinturaria. Na avaliação do processo do molho testou-se uma protease e uma lipase contra um molhante e um desengordurante tradicional, agentes químicos normalmente utilizados no molho mas menos biodegradáveis que as enzimas testadas. Salienta-se o bom resultado obtido quanto à eficiência do molho Na avaliação do processo de caleiro testaram-se várias alternativas no sentido da redução da quantidade de sulfureto de sódio utilizada e da minimização da carga poluente. Entre as alternativas, depilação por oxidação, depilação enzimática com e sem destruição do pêlo, elegeu-se a depilação enzimática sem destruição do pêlo que conduziu a resultados com menor impacto ambiental, nomeadamente a redução da % da quantidade de sulfureto de sódio, sendo a redução da carga poluente de 4,19 % de sulfureto, 32.80% de sólidos suspensos totais (SST),27.09% de sólidos totais (ST) e de 76.90% da carência química de oxigénio (CQO) no efluente de caleiro. No processo do curtume da pele é utilizado crómio como agente de curtume em cerca de 80% das peles tratadas, sendo este metal problemático em termos ambientais. No sentido de reduzir a quantidade de crómio utilizada no processo foi realizado um planeamento factorial onde as variáveis a estudar foram a concentração de crómio e a temperatura, tendo este como objectivo observar qual a quantidade mínima de crómio necessária para termos um produto final nas condições desejadas e gerando um menor impacto ambiental. Concluiu-se desenvolvendo um processo que mostra ser possível reduzir a quantidade de sal de crómio de 7% para 5%, além de ter um impacto ambiental claramente menos agressivo nos efluentes de curtume gerado. Este processo quando comparado com o processo tradicional permite a redução de 27% na CQO, 79% nos SST, 11% nos ST e 38% no teor de crómio Na avaliação do processo de tinturaria foi estudado um processo compacto contra o processo tradicional, tendo-se concluído pelo menor impacto ambiental do processo estudado, nomeadamente ao nível da redução do consumo de água e da carga poluente gerada. A comparação dos dois processos, no que respeita à carga poluente gerada, permitiu concluir por uma redução de 39% da CQO, 50% dos SST, e 12% dos ST quando aplicado o processo compacto Por fim foi feita uma avaliação do impacto ambiental do efluente global gerado pelos processos considerados com menor impacto ambiental contra o processo tradicional, normalmente aplicado na indústria. A aplicação do conjunto dos processos desenvolvidos, quando comparada com a aplicação do conjunto dos processos tradicionais, mostra uma redução de 1% no sulfureto, 40% na CQO, 60 % nos SST, 42 % no crómio e 11% nos ST, mostrando claramente que é possível reduzir a carga poluente da indústria de curtumes atuando no processo. Este trabalho mostrou a importância de atuar no processo para minimizar os custos de tratamento e mesmo de investimento dos efluentes da indústria de curtumes. Importa salientar que os processos desenvolvidos necessitam de validação a uma escala semi-industrial.

Optimization of wastewater quality in the Sines refinery

In order to address and resolve the wastewater contamination problem of the Sines refinery with the main objective of optimizing the quality of this stream and reducing the costs charged to the refinery, a dynamic mass balance was developed nd implemented for ammonia and polar oil and grease (O&G) contamination in the wastewater circuit. The inadequate routing of sour gas from the sour water stripping unit and the kerosene caustic washing unit, were identified respectively as the major source of ammonia and polar substances present in the industrial wastewater effluent. For the O&G content, a predictive model was developed for the kerosene caustic washing unit, following the Projection to Latent Structures (PLS) approach. Comparison between analytical data for ammonia and polar O&G concentrations in refinery wastewater originating from the Dissolved Air Flotation (DAF) effluent and the model predictions of the dynamic mass balance calculations are in a very good agreement and highlights the dominant impact of the identified streams for the wastewater contamination levels. The ammonia contamination problem was solved by rerouting the sour gas through an existing clogged line with ammonia salts due to a non-insulated line section, while for the O&G a dynamic mass balance was implemented as an online tool, which allows for prevision of possible contamination situations and taking the required preventive actions, and can also serve as a basis for establishing relationships between the O&G contamination in the refinery wastewater with the properties of the refined crude oils and the process operating conditions. The PLS model developed could be of great asset in both optimizing the existing and designing new refinery wastewater treatment units or reuse schemes. In order to find a possible treatment solution for the spent caustic problem, an on-site pilot plant experiments for NaOH recovery from the refinery kerosene caustic washing unit effluent using an alkaline-resistant nanofiltration (NF) polymeric membrane were performed in order to evaluate its applicability for treating these highly alkaline and contaminated streams. For a constant operating pressure and temperature and adequate operating conditions, 99.9% of oil and grease rejection and 97.7% of chemical oxygen demand (COD) rejection were observed. No noticeable membrane fouling or flux decrease were registered until a volume concentration factor of 3. These results allow for NF permeate reuse instead of fresh caustic and for significant reduction of the wastewater contamination, which can result in savings of 1.5 M€ per year at the current prices for the largest Portuguese oil refinery. The capital investments needed for implementation of the required NF membrane system are less than 10% of those associated with the traditional wet air oxidation solution of the spent caustic problem. The operating costs are very similar, but can be less than half if reusing the NF concentrate in refinery pH control applications. The payback period was estimated to be 1.1 years. Overall, the pilot plant experimental results obtained and the process economic evaluation data indicate a very competitive solution through the proposed NF treatment process, which represents a highly promising alternative to conventional and existing spent caustic treatment units.

Coupling organic substrate removal to methane production in a fully biological microbial electrolysis cell

Microbial electrolysis cells (MECs) are an innovative and emerging technique based on the use of solid-state electrodes to stimulate microbial metabolism for wastewater treatment and simultaneous production of value-added compounds (such as methane). This research studied the performance of a two-chamber MEC in terms of organic matter oxidation (at the anode) and methane production (at the cathode). MEC‟s anode had been previously inoculated with an activated sludge, whereas the cathode chamber inoculum was an anaerobic sludge (containing methanogenic microorganisms). During the experimentation, the bioanode was continuously fed with synthetic solutions in anaerobic basal medium, at an organic load rate (OLR) of around 1 g L-1 d-1, referred to the chemical oxygen demand (COD). At the beginning (Run I), the feeding solution contained acetate and subsequently (Run II) it was replaced with a more complex solution containing soluble organic compounds other than acetate. For both conditions, the anode potential was controlled at -0.1 V vs. standard hydrogen electrode, by means of a potentiostat. During Run I, over 80% of the influent acetate was anaerobically oxidized at the anode, and the resulting electric current was recovered as methane at the cathode (with a cathode capture efficiency, CCE, accounting around 115 %). The average energy efficiency of the system (i.e., the energy captured into methane relative to the electrical energy input) under these conditions was over 170%. However, reactor‟s performance decreased over time during this run. Throughout Run II, a substrate oxidation over 60% (on COD basis) was observed. The electric current produced (57% of coulombic efficiency) was also recovered as methane, with a CCE of 90%. For this run the MEC‟s average energy efficiency accounted for almost 170 %. During all the experimentation, a very low biomass growth was observed at the anode whereas ammonium was transferred through the cationic membrane and concentrated at the cathode. Tracer experiments and scanning electron microscopy analyses were also carried out to gain a deeper insight into the reactor performance and also to investigate the possible reasons for partial loss of performance. In conclusion, this research suggests the great potential of MEC to successfully treat low-strength wastewaters, with high energy efficiency and very low sludge production.

The effects of detergent loading on rotating biological contactor (RBC) wastewater treatment efficiency

There are presently over 182 RBC plants, treating domestic wastewater, in the Republic of Ireland, 136 of which have been installed since 1986. The use of this treatment plant technology, although not new, is becoming increasingly popular. The aim of this research was to assess the effects that a household detergent has on rotating biological contractor treatment plant efficiency. Household detergents contribute phosphorus to the surrounding environment and can also remove beneficial biomass from the disc media. A simple modification was made to a conventional flat disc unit to increase the oxygen transfer of the process. The treatment efficiency of the modified RBC (with aeration cups attached) was assessed against a parallel conventional system, with and without degergent loading. The parameters monitored were chemical oxygen demand (COD), bio-chemical oxygen demand (BOD), nitrates, phosphates, dissolved oxygen, the motors power consumption, pH, and temperature. Some microscopic analysis of the biofilm was also to be carried out. The treatment efficiency of both units was compared, based on COD/BOD removal. The degree of nitrification achievable by both units was also assessed with any fluctuations in pH noted. Monitoring of the phosphorus removal capabilities of both units was undertaken. Relationships between detergent concentrations and COD removal efficiencies were also analysed.

Oxidative and glycogenolytic cCapacities within the developing chick heart.

Cardiac morphogenesis and function are known to depend on both aerobic and anaerobic energy-producing pathways. However, the relative contribution of mitochondrial oxidation and glycogenolysis, as well as the determining factors of oxygen demand in the distinct chambers of the embryonic heart, remains to be investigated. Spontaneously beating hearts isolated from stage 11, 20, and 24HH chick embryos were maintained in vitro under controlled metabolic conditions. O(2) uptake and glycogenolytic rate were determined in atrium, ventricle, and conotruncus in the absence or presence of glucose. Oxidative capacity ranged from 0.2 to 0.5 nmol O(2)/(h.microg protein), did not depend on exogenous glucose, and was the highest in atria at stage 20HH. However, the highest reserves of oxidative capacity, assessed by mitochondrial uncoupling, were found at the youngest stage and in conotruncus, representing 75 to 130% of the control values. At stage 24HH, glycogenolysis in glucose-free medium was 0.22, 0.17, and 0.04 nmol glucose U(h.microg protein) in atrium, ventricle, and conotruncus, respectively. Mechanical loading of the ventricle increased its oxidative capacity by 62% without altering glycogenolysis or lactate production. Blockade of glycolysis by iodoacetate suppressed lactate production but modified neither O(2) nor glycogen consumption in substrate-free medium. These findings indicate that atrium is the cardiac chamber that best utilizes its oxidative and glycogenolytic capacities and that ventricular wall stretch represents an early and major determinant of the O(2) uptake. Moreover, the fact that O(2) and glycogen consumptions were not affected by inhibition of glyceraldehyde-3-phosphate dehydrogenase provides indirect evidence for an active glycerol-phosphate shuttle in the embryonic cardiomyocytes.

Looking for orders of magnitude : five essays in trade and the environment and economic geography

General Summary Although the chapters of this thesis address a variety of issues, the principal aim is common: test economic ideas in an international economic context. The intention has been to supply empirical findings using the largest suitable data sets and making use of the most appropriate empirical techniques. This thesis can roughly be divided into two parts: the first one, corresponding to the first two chapters, investigates the link between trade and the environment, the second one, the last three chapters, is related to economic geography issues. Environmental problems are omnipresent in the daily press nowadays and one of the arguments put forward is that globalisation causes severe environmental problems through the reallocation of investments and production to countries with less stringent environmental regulations. A measure of the amplitude of this undesirable effect is provided in the first part. The third and the fourth chapters explore the productivity effects of agglomeration. The computed spillover effects between different sectors indicate how cluster-formation might be productivity enhancing. The last chapter is not about how to better understand the world but how to measure it and it was just a great pleasure to work on it. "The Economist" writes every week about the impressive population and economic growth observed in China and India, and everybody agrees that the world's center of gravity has shifted. But by how much and how fast did it shift? An answer is given in the last part, which proposes a global measure for the location of world production and allows to visualize our results in Google Earth. A short summary of each of the five chapters is provided below. The first chapter, entitled "Unraveling the World-Wide Pollution-Haven Effect" investigates the relative strength of the pollution haven effect (PH, comparative advantage in dirty products due to differences in environmental regulation) and the factor endowment effect (FE, comparative advantage in dirty, capital intensive products due to differences in endowments). We compute the pollution content of imports using the IPPS coefficients (for three pollutants, namely biological oxygen demand, sulphur dioxide and toxic pollution intensity for all manufacturing sectors) provided by the World Bank and use a gravity-type framework to isolate the two above mentioned effects. Our study covers 48 countries that can be classified into 29 Southern and 19 Northern countries and uses the lead content of gasoline as proxy for environmental stringency. For North-South trade we find significant PH and FE effects going in the expected, opposite directions and being of similar magnitude. However, when looking at world trade, the effects become very small because of the high North-North trade share, where we have no a priori expectations about the signs of these effects. Therefore popular fears about the trade effects of differences in environmental regulations might by exaggerated. The second chapter is entitled "Is trade bad for the Environment? Decomposing worldwide SO2 emissions, 1990-2000". First we construct a novel and large database containing reasonable estimates of SO2 emission intensities per unit labor that vary across countries, periods and manufacturing sectors. Then we use these original data (covering 31 developed and 31 developing countries) to decompose the worldwide SO2 emissions into the three well known dynamic effects (scale, technique and composition effect). We find that the positive scale (+9,5%) and the negative technique (-12.5%) effect are the main driving forces of emission changes. Composition effects between countries and sectors are smaller, both negative and of similar magnitude (-3.5% each). Given that trade matters via the composition effects this means that trade reduces total emissions. We next construct, in a first experiment, a hypothetical world where no trade happens, i.e. each country produces its imports at home and does no longer produce its exports. The difference between the actual and this no-trade world allows us (under the omission of price effects) to compute a static first-order trade effect. The latter now increases total world emissions because it allows, on average, dirty countries to specialize in dirty products. However, this effect is smaller (3.5%) in 2000 than in 1990 (10%), in line with the negative dynamic composition effect identified in the previous exercise. We then propose a second experiment, comparing effective emissions with the maximum or minimum possible level of SO2 emissions. These hypothetical levels of emissions are obtained by reallocating labour accordingly across sectors within each country (under the country-employment and the world industry-production constraints). Using linear programming techniques, we show that emissions are reduced by 90% with respect to the worst case, but that they could still be reduced further by another 80% if emissions were to be minimized. The findings from this chapter go together with those from chapter one in the sense that trade-induced composition effect do not seem to be the main source of pollution, at least in the recent past. Going now to the economic geography part of this thesis, the third chapter, entitled "A Dynamic Model with Sectoral Agglomeration Effects" consists of a short note that derives the theoretical model estimated in the fourth chapter. The derivation is directly based on the multi-regional framework by Ciccone (2002) but extends it in order to include sectoral disaggregation and a temporal dimension. This allows us formally to write present productivity as a function of past productivity and other contemporaneous and past control variables. The fourth chapter entitled "Sectoral Agglomeration Effects in a Panel of European Regions" takes the final equation derived in chapter three to the data. We investigate the empirical link between density and labour productivity based on regional data (245 NUTS-2 regions over the period 1980-2003). Using dynamic panel techniques allows us to control for the possible endogeneity of density and for region specific effects. We find a positive long run elasticity of density with respect to labour productivity of about 13%. When using data at the sectoral level it seems that positive cross-sector and negative own-sector externalities are present in manufacturing while financial services display strong positive own-sector effects. The fifth and last chapter entitled "Is the World's Economic Center of Gravity Already in Asia?" computes the world economic, demographic and geographic center of gravity for 1975-2004 and compares them. Based on data for the largest cities in the world and using the physical concept of center of mass, we find that the world's economic center of gravity is still located in Europe, even though there is a clear shift towards Asia. To sum up, this thesis makes three main contributions. First, it provides new estimates of orders of magnitudes for the role of trade in the globalisation and environment debate. Second, it computes reliable and disaggregated elasticities for the effect of density on labour productivity in European regions. Third, it allows us, in a geometrically rigorous way, to track the path of the world's economic center of gravity.

Quality of surface water related to land use: a case study in a catchment with small farms and intensive vegetable crop production in southern Brazil

Water degradation is strongly related to agricultural activity. The aim of this study was to evaluate the influence of land use and some environmental components on surface water quality in the Campestre catchment, located in Colombo, state of Parana, Brazil. Physical and chemical attributes were analyzed (total nitrogen, ammonium, nitrate, total phosphorus, electrical conductivity, pH, temperature, turbidity, total solids, biological oxygen demand, chemical oxygen demand and dissolved oxygen). Monthly samples of the river water were taken over one year at eight monitoring sites, distributed over three sub-basins. Overall, water quality was worse in the sub-basin with a higher percentage of agriculture, and was also affected by a lower percentage of native forest and permanent preservation area, and a larger drainage area. Water quality was also negatively affected by the presence of agriculture in the riparian zone. In the summer season, probably due to higher rainfall and intensive soil use, a higher concentration of total nitrogen and particulate nitrogen was observed, as well as higher electrical conductivity, pH and turbidity. All attributes, except for total phosphorus, were in compliance with Brazilian Conama Resolution Nº 357/2005 for freshwater class 1. However, it should be noted that these results referred to the base flow and did not represent a discharge condition since most of the water samples were not collected at or near the rainfall event.

Flotaatio jätevedenpuhdistamon tertiäärivaiheena eräässä paperitehtaassa

Työn tavoitteena oli selvittää, kuinka tehokkaasti pystytään aktiivilieteprosessin läpikäynyttä, jälkiselkeytettyä vettä edelleen puhdistamaan flotaatiolla ennen sen johtamista vesistöön. Tarkoituksena oli löytää sellaiset kemikaalit ja näiden annokset, joilla tehtaalle asetetut jätevesien lupa-arvot voitaisiin huonossa tilanteessa, jätevesikuormitushuippujen aikana alittamaan. Työn kirjallisessaosassa tarkasteltiin lyhyesti, minkälaista jätevesikuormaa mekaanista massaa valmistavalta tehtaalta yleensä syntyy ja millaiset ovat tavanomaiset puhdistusmenetelmät. Myös flotaation teoriaa esiteltiin. Kokeellinen osa koostui kolmesta päävaiheesta: esi- eli niin sanotuista kuppikokeista, pilot-flotaatiokoeajoista jalaitosmittakaavan flotaatiokoeajoista. Esikokeet tehtiin niin kutsutulla Jar Test -laitteistolla ja pilot-flotaatiolaitteistona työssä käytettiin YIT:n valmistamaa pilot-flotaattoria. Laitosmittakaavan flotaatioaltaat olivat aikaisemmin biolietteen tiivistykseen käytettyjä, myöhemmin tertiääripuhdistukseen modifioituja flotaatioaltaita. Laitosmittakaavan flotaatiokoeajoissa testattiin neljän eri saostuskemikaalin ¿ polyalumiinikloridin (KEMPAC 18), rautapitoisen alumiinisulfaatin (AVR), ferrisulfaatin ja alumiinisulfaatin ¿ tehokkuutta tertiäärivaiheessa käsiteltävän veden puhdistajana. Esi- ja pilot-kokeiden perusteella laitosmittakaavan kokeisiin valittiin saostuskemikaalien rinnalle polymeeriksi Superfloc C 491. AVR- ja alumiinisulfaattiannokset laitosmittakaavan kokeissa olivat 200 ppm ja 400 ppm. KEMPAC 18- ja ferrisulfaattiannokset olivat 200ppm, 400 ppm ja 600 ppm. Polymeeriannos kokeissa oli pääasiassa 1,2 ppm. Tertiäärivaiheeseen tulevasta vedestä ja poistuvasta kirkasteesta määritettiin kiintoaine, pH, liukoinen ja kokonais-COD, liukoinen ja kokonaisfosfori sekä liukoinen ja kokonaistyppi. Laitosmittakaavan koeajojen tulosten mukaan eniten tertiäärivaiheessa saatiin käsiteltävästä vedestä erotettua fosforia ja toiseksi eniten COD:ta. Typpireduktiot olivat verrattain alhaiset ja myös kiintoainereduktiot jäivät usein pieniksi tai olivat jopa negatiiviset. Kaikki saostuskemikaalit saostivat COD- ja ravinnekuormaa. Eniten kuormaa saostuskemikaaleista saatiin erotettua AVR:llä ja toiseksi eniten KEMPAC 18:lla. Laitteistojen käyttökustannuksia huomioimatta AVR olisi edullisin vaihtoehto saostuskemikaaaliksietenkin pidempiaikaisessa käytössä. Lisäksi työssä tutkittiin polymeeriannoksen kasvattamisen 1,2 ppm:stä 2,5 ppm:ään vaikutusta puhdistustulokseen, kun saostuskemikaaliannos pidettiin vakiona. Tulosten mukaan polymeeriannoksen kasvattaminen kasvatti kokonais-COD- ja kokonaisfosforireduktiota. Myöslaitosmittakaavan flotaatioaltaiden pohjaputkistoja vertailtiin kiintoainereduktioiden perusteella. Kokeissa saatujen tulosten mukaan ei voitu sanoa, oliko toisen altaan pitkä kirkasteenpoistoputki vai toisen altaan lyhyt kirkasteenpoistoputki parempi vaihtoehto.