Distal locking of femoral nails: evaluation of a new radiation-independent targeting system.

OBJECTIVES: The purpose of this study was to assess the effectiveness of a novel radiation-independent aiming device for distal locking of intramedullary nails in a human cadaver model. METHODS: A new targeting system was used in 25 intact human cadaver femora for the distal locking procedure after insertion of an intramedullary nail. The number of successful screw placements and the time needed for this locking procedure were recorded. The accuracy of the aiming process was evaluated by computed tomography. RESULTS: The duration of the distal locking process was 8.0 ± 1.8 minutes (mean ± SD; range, 4-11 minutes). None of the screw placements required fluoroscopic guidance. Computed tomography revealed high accuracy of the locking process. The incidence angle (α) of the locking screws through the distal locking holes of the nail was 86.8° ± 5.0° (mean ± SD; range, 80°-96°). Targeting failed in 1 static locking screw because of a material defect in the drilling sleeve. CONCLUSIONS: This cadaver study indicated that an aiming arm-based targeting device is highly reliable and accurate. The promising results suggest that it will help to decrease radiation exposure compared with the traditional "free-hand technique."

A new drug delivery system inhibits uveitis in an animal model after cataract surgery.

Cataract surgery is a common ocular surgical procedure consisting in the implantation of an artificial intraocular lens (IOL) to replace the ageing, dystrophic or damaged natural one. The management of postoperative ocular inflammation is a major challenge especially in the context of pre-existing uveitis. The association of the implanted IOL with a drug delivery system (DDS) allows the prolonged intraocular release of anti-inflammatory agents after surgery. Thus IOL-DDS represents an "all in one" strategy that simultaneously addresses both cataract and inflammation issues. Polymeric DDS loaded with two model anti-inflammatory drugs (triamcinolone acetonide (TA) and cyclosporine A (CsA)) were manufactured in a novel way and tested regarding their efficiency for the management of intraocular inflammation during the 3 months following surgery. The study involved an experimentally induced uveitis in rabbits. Experimental results showed that medicated DDS efficiently reduced ocular inflammation (decrease of protein concentration in aqueous humour, inflammatory cells in aqueous humour and clinical score). Additionally, more than 60% of the loading dose remained in the DDS at the end of the experiment, suggesting that the system could potentially cover longer inflammatory episodes. Thus, IOL-DDS were demonstrated to inhibit intraocular inflammation for at least 3 months after cataract surgery, representing a potential novel approach to cataract surgery in eyes with pre-existing uveitis.

A new technique with high reproducibility to estimate renal oxygenation using BOLD-MRI in chronic kidney disease.

OBJECTIVES: To assess inter-observer variability of renal blood oxygenation level-dependent MRI (BOLD-MRI) using a new method of analysis, called the concentric objects (CO) technique, in comparison with the classical ROI (region of interest)-based technique. METHODS: MR imaging (3T) was performed before and after furosemide in 10 chronic kidney disease (CKD) patients (mean eGFR 43±24ml/min/1.73m(2)) and 10 healthy volunteers (eGFR 101±28ml/min1.73m(2)), and R2* maps were determined on four coronal slices. In the CO-technique, R2* values were based on a semi-automatic procedure that divided each kidney in six equal layers, whereas in the ROI-technique, all circles (ROIs) were placed manually in the cortex and medulla. The mean R2*values as assessed by two independent investigators were compared. RESULTS: With the CO-technique, inter-observer variability was 0.7%-1.9% across all layers in non-CKD, versus 1.6%-3.8% in CKD. With the ROI-technique, median variability for cortical and medullary R2* values was 3.6 and 6.8% in non-CKD, versus 4.7 and 12.5% in CKD; similar results were observed after furosemide. CONCLUSION: The CO-technique offers a new, investigator-independent, highly reproducible alternative to the ROI-based technique to estimate renal tissue oxygenation in CKD.

Characterization of a new potential virulence factor of Microsporum canis, the secreted subtilisin Sub6

Background: Microsporum canis is a dermatophyte responsible for cutaneous superficial mycoses in domestic carnivores and humans. The pathogenesis of dermatophytoses, including M. canis infections, remains poorly understood. Secreted proteases including members of the subtilisin family are thought to be involved in the infection process. In particular the subtilisin Sub6 could represent a major virulence factor.Objective: The aim of this work was to (i) isolate the M. canis SUB6 genomic DNA and cDNA (ii) produce Sub6 as a recombinant protease (rSub6) and (iii) produce a specific anti-Sub6 polyclonal serum. Material and methods: Genomic SUB6 was amplified by PCR using specific primers and M. canis IHEM 21239 DNA as a target. The SUB6 cDNA was obtained by reverse transcriptase (RT)-PCR using total RNA extracted from the same M. canis strain grown in liquid medium containing feline keratin as unique nitrogen source. Both SUB6 cDNA and genomic DNA were sequenced. The SUB6 cDNA was cloned in pPICZA to produce recombinant Sub6 (rSub6) in Pichia pastoris KM71. This protease rSub6 was produced in methanol medium at a yield of 30 mg ml)1 and purified by anion exchange chromatography using a DEAE-sepharose column. Polyclonal antibodies against purified rSub6 were produced in a rabbit using a standard immunization procedure with saponin as the adjuvant. Seventy days after the first immunization, serum was collected and IgG were purified by affinity chromatography.Results: The coding sequence for M. canis SUB6 from genomic DNA contains 1410 bp and 3 introns, while the cDNA contains a 1221 bp open reading frame. Deduced amino acid sequence analysis revealed that Sub6 is synthesized as a 406 amino acids preproprotein. The predicted catalytic domain has 286 amino acids, a molecular mass of 29.1 kDa and five potential N-glycosylation sites. SDS-PAGE of rSub6 revealed a single polypeptide chain with an apparent molecular mass of 37 kDa. Purified rabbit IgG were shown to be specific for Sub6 using ELISA.Conclusion: We have characterized for the first time Sub6 from a dermatophyte species as a recombinant secreted active enzyme and purified it until homogeneity. Active rSub6 and Sub6 specific antiserum will be used to further study the role of M. canis Sub6 protease in pathogenesis, notably the pattern of in vivo Sub6 secretion in different host species.

A new poly(ortho ester)-based drug delivery system as an adjunct treatment in filtering surgery.

PURPOSE: Pharmacologic modulation of wound healing after glaucoma filtering surgery remains a major clinical challenge in ophthalmology. Poly(ortho ester) (POE) is a bioerodible and biocompatible viscous polymer potentially useful as a sustained drug delivery system that allows the frequency of intraocular injections to be reduced. The purpose of this study was to determine the efficacy of POE containing a precise amount of 5-fluorouracil (5-FU) in an experimental model of filtering surgery in the rabbit. METHODS: Trabeculectomy was performed in pigmented rabbit eyes. An ointmentlike formulation of POE containing 1% wt/wt 5-FU was injected subconjunctivally at the site of surgery, during the procedure. Intraocular pressure (IOP), bleb persistence, and ocular inflammatory reaction were monitored until postoperative day 30. Quantitative analysis of 5-FU was performed in the anterior chamber. Histologic analysis was used to assess the appearance of the filtering fistula and the polymer's biocompatibility. RESULTS: The decrease in IOP from baseline and the persistence of the filtering bleb were significantly more marked in the 5-FU-treated eyes during postoperative days 9 through 28. Corneal toxicity triggered by 5-FU was significantly lower in the group that received 5-FU in POE compared with a 5-FU tamponade. Histopathologic evaluation showed that POE was well tolerated, and no fibrosis occurred in eyes treated with POE containing 5-FU. CONCLUSIONS: In this rabbit model of trabeculectomy, the formulation based on POE and containing a precise amount of 5-FU reduced IOP and prolonged bleb persistence in a way similar to the conventional method of a 5-FU tamponade, while significantly reducing 5-FU toxicity.

Functional independence within the self-memory system: new insights from two cases of developmental amnesia.

Neuropsychological and neuroimaging data suggest that the self-memory system can be fractionated into three functionally independent systems processing personal information at several levels of abstraction, including episodic memories of one's life (episodic autobiographical memory, EAM), semantic knowledge of facts about one's life (semantic autobiographical memory, SAM), and semantic knowledge of one's personality [conceptual self, (CS)]. Through the study of two developmental amnesic patients suffering of neonatal brain injuries, we explored how the different facets of the self-memory system develop when growing up with bilateral hippocampal atrophy. Neuropsychological evaluations showed that both of them suffered from dramatic episodic learning disability with no sense of recollection (Remember/Know procedure), whereas their semantic abilities differed, being completely preserved (Valentine) or not (Jocelyn). Magnetic resonance imaging, including quantitative volumetric measurements of the hippocampus and adjacent (entorhinal, perirhinal, and temporopolar) cortex, showed severe bilateral atrophy of the hippocampus in both patients, with additional atrophy of adjacent cortex in Jocelyn. Exploration of EAM and SAM according to lifetime periods covering the entire lifespan (TEMPAu task, Piolino et al., 2009) showed that both patients had marked impairments in EAM, as they lacked specificity, details and sense of recollection, whereas SAM was completely normal in Valentine, but impaired in Jocelyn. Finally, measures of patients' CS (Tennessee Self-Concept Scale, Fitts and Warren, 1996), checked by their mothers, were generally within normal range, but both patients showed a more positive self-concept than healthy controls. These two new cases support a modular account of the medial-temporal lobe with episodic memory and recollection depending on the hippocampus, and semantic memory and familiarity on adjacent cortices. Furthermore, they highlight developmental episodic and semantic functional independence within the self-memory system suggesting that SAM and CS may be acquired without episodic memories.

A novel procedure for establishing clinching parameters for high strength steel sheet

The building industry has a particular interest in using clinching as a joining method for frame constructions of light-frame housing. Normally many clinch joints are required in joining of frames.In order to maximise the strength of the complete assembly, each clinch joint must be as sound as possible. Experimental testing is the main means of optimising a particular clinch joint. This includes shear strength testing and visual observation of joint cross-sections. The manufacturers of clinching equipment normally perform such experimental trials. Finite element analysis can also be used to optimise the tool geometry and the process parameter, X, which represents the thickness of the base of the joint. However, such procedures require dedicated software, a skilled operator, and test specimens in order to verify the finite element model. In addition, when using current technology several hours' computing time may be necessary. The objective of the study was to develop a simple calculation procedure for rapidly establishing an optimum value for the parameter X for a given tool combination. It should be possible to use the procedure on a daily basis, without stringent demands on the skill of the operator or the equipment. It is also desirable that the procedure would significantly decrease thenumber of shear strength tests required for verification. The experimental workinvolved tests in order to obtain an understanding of the behaviour of the sheets during clinching. The most notable observation concerned the stage of the process in which the upper sheet was initially bent, after which the deformation mechanism changed to shearing and elongation. The amount of deformation was measured relative to the original location of the upper sheet, and characterised as the C-measure. By understanding in detail the behaviour of the upper sheet, it waspossible to estimate a bending line function for the surface of the upper sheet. A procedure was developed, which makes it possible to estimate the process parameter X for each tool combination with a fixed die. The procedure is based on equating the volume of material on the punch side with the volume of the die. Detailed information concerning the behaviour of material on the punch side is required, assuming that the volume of die does not change during the process. The procedure was applied to shear strength testing of a sample material. The sample material was continuously hot-dip zinc-coated high-strength constructional steel,with a nominal thickness of 1.0 mm. The minimum Rp0.2 proof stress was 637 N/mm2. Such material has not yet been used extensively in light-frame housing, and little has been published on clinching of the material. The performance of the material is therefore of particular interest. Companies that use clinching on a daily basis stand to gain the greatest benefit from the procedure. By understanding the behaviour of sheets in different cases, it is possible to use data at an early stage for adjusting and optimising the process. In particular, the functionality of common tools can be increased since it is possible to characterise the complete range of existing tools. The study increases and broadens the amount ofbasic information concerning the clinching process. New approaches and points of view are presented and used for generating new knowledge.

ICA Cleaning procedure for EEG signals analysis: application to Alzheimer's disease detection

To develop systems in order to detect Alzheimer’s disease we want to use EEG signals. Available database is raw, so the first step must be to clean signals properly. We propose a new way of ICA cleaning on a database recorded from patients with Alzheimer's disease (mildAD, early stage). Two researchers visually inspected all the signals (EEG channels), and each recording's least corrupted (artefact-clean) continuous 20 sec interval were chosen for the analysis. Each trial was then decomposed using ICA. Sources were ordered using a kurtosis measure, and the researchers cleared up to seven sources per trial corresponding to artefacts (eye movements, EMG corruption, EKG, etc), using three criteria: (i) Isolated source on the scalp (only a few electrodes contribute to the source), (ii) Abnormal wave shape (drifts, eye blinks, sharp waves, etc.), (iii) Source of abnormally high amplitude ( �100 �V). We then evaluated the outcome of this cleaning by means of the classification of patients using multilayer perceptron neural networks. Results are very satisfactory and performance is increased from 50.9% to 73.1% correctly classified data using ICA cleaning procedure.

Predicting richness and composition in mountain insect communities at high resolution: a new test of the SESAM framework

Aim The aim of this study was to test different modelling approaches, including a new framework, for predicting the spatial distribution of richness and composition of two insect groups. Location The western Swiss Alps. Methods We compared two community modelling approaches: the classical method of stacking binary prediction obtained fromindividual species distribution models (binary stacked species distribution models, bS-SDMs), and various implementations of a recent framework (spatially explicit species assemblage modelling, SESAM) based on four steps that integrate the different drivers of the assembly process in a unique modelling procedure. We used: (1) five methods to create bS-SDM predictions; (2) two approaches for predicting species richness, by summing individual SDM probabilities or by modelling the number of species (i.e. richness) directly; and (3) five different biotic rules based either on ranking probabilities from SDMs or on community co-occurrence patterns. Combining these various options resulted in 47 implementations for each taxon. Results Species richness of the two taxonomic groups was predicted with good accuracy overall, and in most cases bS-SDM did not produce a biased prediction exceeding the actual number of species in each unit. In the prediction of community composition bS-SDM often also yielded the best evaluation score. In the case of poor performance of bS-SDM (i.e. when bS-SDM overestimated the prediction of richness) the SESAM framework improved predictions of species composition. Main conclusions Our results differed from previous findings using community-level models. First, we show that overprediction of richness by bS-SDM is not a general rule, thus highlighting the relevance of producing good individual SDMs to capture the ecological filters that are important for the assembly process. Second, we confirm the potential of SESAM when richness is overpredicted by bS-SDM; limiting the number of species for each unit and applying biotic rules (here using the ranking of SDM probabilities) can improve predictions of species composition

New Insights in the Diagnosis and Treatment of Heart Failure.

Cardiovascular disease is the leading cause of mortality in the US and in westernized countries with ischemic heart disease accounting for the majority of these deaths. Paradoxically, the improvements in the medical and surgical treatments of acute coronary syndrome are leading to an increasing number of "survivors" who are then developing heart failure. Despite considerable advances in its management, the gold standard for the treatment of end-stage heart failure patients remains heart transplantation. Nevertheless, this procedure can be offered only to a small percentage of patients who could benefit from a new heart due to the limited availability of donor organs. The aim of this review is to evaluate the safety and efficacy of innovative approaches in the diagnosis and treatment of patients refractory to standard medical therapy and excluded from cardiac transplantation lists.

The new final Clinical Skills examination in human medicine in Switzerland: Essential steps of exam development, implementation and evaluation, and central insights from the perspective of the national Working Group.

OBJECTIVE: Since 2011, the new national final examination in human medicine has been implemented in Switzerland, with a structured clinical-practical part in the OSCE format. From the perspective of the national Working Group, the current article describes the essential steps in the development, implementation and evaluation of the Federal Licensing Examination Clinical Skills (FLE CS) as well as the applied quality assurance measures. Finally, central insights gained from the last years are presented. METHODS: Based on the principles of action research, the FLE CS is in a constant state of further development. On the foundation of systematically documented experiences from previous years, in the Working Group, unresolved questions are discussed and resulting solution approaches are substantiated (planning), implemented in the examination (implementation) and subsequently evaluated (reflection). The presented results are the product of this iterative procedure. RESULTS: The FLE CS is created by experts from all faculties and subject areas in a multistage process. The examination is administered in German and French on a decentralised basis and consists of twelve interdisciplinary stations per candidate. As important quality assurance measures, the national Review Board (content validation) and the meetings of the standardised patient trainers (standardisation) have proven worthwhile. The statistical analyses show good measurement reliability and support the construct validity of the examination. Among the central insights of the past years, it has been established that the consistent implementation of the principles of action research contributes to the successful further development of the examination. CONCLUSION: The centrally coordinated, collaborative-iterative process, incorporating experts from all faculties, makes a fundamental contribution to the quality of the FLE CS. The processes and insights presented here can be useful for others planning a similar undertaking.

Identification of new transformation products during enzymatic treatment of tetracycline and erythromycin antibiotics at laboratory scale by an on-line turbulent flow liquid-chromatography coupled to a high resolution mass spectrometer LTQ-Orbitrap

This work describes the formation of transformation products (TPs) by the enzymatic degradation at laboratory scale of two highly consumed antibiotics: tetracycline (Tc) and erythromycin (ERY). The analysis of the samples was carried out by a fast and simple method based on the novel configuration of the on-line turbulent flow system coupled to a hybrid linear ion trap – high resolution mass spectrometer. The method was optimized and validated for the complete analysis of ERY, Tc and their transformation products within 10 min without any other sample manipulation. Furthermore, the applicability of the on-line procedure was evaluated for 25 additional antibiotics, covering a wide range of chemical classes in different environmental waters with satisfactory quality parameters. Degradation rates obtained for Tc by laccase enzyme and ERY by EreB esterase enzyme without the presence of mediators were ∼78% and ∼50%, respectively. Concerning the identification of TPs, three suspected compounds for Tc and five of ERY have been proposed. In the case of Tc, the tentative molecular formulas with errors mass within 2 ppm have been based on the hypothesis of dehydroxylation, (bi)demethylation and oxidation of the rings A and C as major reactions. In contrast, the major TP detected for ERY has been identified as the “dehydration ERY-A”, with the same molecular formula of its parent compound. In addition, the evaluation of the antibiotic activity of the samples along the enzymatic treatments showed a decrease around 100% in both cases

Identification of Races of Selected Isolates of Uromyces appendiculatus from Minas Gerais (Brazil) Based on the new international classification system

Twelve single-pustule isolates of Uromyces appendiculatus, the etiological agent of common bean rust, were collected in the state of Minas Gerais, Brazil, and classified according to the new international differential series and the binary nomenclature system proposed during the 3rd Bean Rust Workshop. These isolates have been used to select rust-resistant genotypes in a bean breeding program conducted by our group. The twelve isolates were classified into seven different physiological races: 21-3, 29-3, 53-3, 53-19, 61-3, 63-3 and 63-19. Races 61-3 and 63-3 were the most frequent in the area. They were represented by five and two isolates, respectively. The other races were represented by just one isolate. This is the first time the new international classification procedure has been used for U. appendiculatus physiological races in Brazil. The general adoption of this system will facilitate information exchange, allowing the cooperative use of the results obtained by different research groups throughout the world. The differential cultivars Mexico 309, Mexico 235 and PI 181996 showed resistance to all of the isolates that were characterized. It is suggested that these cultivars should be preferentially used as sources for resistance to rust in breeding programs targeting development lines adapted to the state of Minas Gerais.

A new approach to evaluate imperfection sensitivity in asymmetric bifurcation buckling analysis

A direct procedure for the evaluation of imperfection sensitivity in bifurcation problems is presented. The problems arise in the context of the general theory of elastic stability for discrete structural systems, in which the energy criterion of stability of structures and the total potential energy formulation are employed. In cases of bifurcation buckling the sensitivity of the critical load with respect to an imperfection parameter e is singular at the state given by epsilon =0, so that, a regular perturbation expansion of the solution is not possible. In this work we describe a direct procedure to obtain the relations between the critical loads, the generalized coordinates at the critical state, the eigenvector, and the amplitude of the imperfection, using singular perturbation analysis. The expansions are assumed in terms of arbitrary powers of the imperfection parameter, so that both exponents and coefficients of the expansion are unknown. The solution of the series exponents is obtained by searching the least degenerate solution. The formulation is here applied to asymmetric bifurcations, for which explicit expressions of the coefficients are obtained. The use of the method is illustrated by a simple example, which allows consideration of the main features of the formulation.

The contributions of netnography in new product development

Netnography has been studying in various aspects (e.g. definitions of netnography, application of netngoraphy, conducting procedure…) within different industrial contexts. Besides, there are many studies and researches about new product development in various perspectives, such as new product development models, management of new product development project, or interaction between customers and new product design, and so on. However, the connection and the interaction between netnography and new product development have not been studied recently. This opens opportunities for the writer to study and explore unrevealed issues regarding to applying netnography in new product development. In term of the relation between netnography and new product development, there are numerous of matters need to be explored; for instance, the process of applying netnography in order to benefit to new product development, the involvement degree of netnography in new product development process, or eliminating useless information from netnography so that only crucial data is utilized, and so on. In this thesis, writer focuses on exploring how netnography is applied in new product development process, and what benefits netnography can contribute to the succeed of the project. The aims of this study are to understand how netnography is conducted for new product development purpose, and to analyse the contributions of netnography in the new product development process. To do so, a case-study strategy will be conducted with triple case studies. The case studies are chosen bases on many different criteria in order to select the most relevant cases. Eventually, the writer selected three case studies, which are Sunless tanning product project (HYVE), Listerine (NetBase), and Nivea co-creation and netnography in black and white deodorant. The case study strategy applied in this thesis includes four steps e.g. case selection, data collection, case study analysis, and generating the research outcomes from the analysis. This study of the contributions of netnography in the new product development process may be useful for the readers in many ways. It offers the fundamental knowledge of netnography market research method and basic understanding of new product development process. Additionally, it emphasizes the differences between netnography and other market research methods in order to explain the reasons why many companies and market research agents recently utilized netnography in their market research projects. Furthermore, it highlights the contributions of netnography in the new product development process in order to indicate the importance of netnography in developing new product. Thus, the potential readers of the study can be students, marketers, researchers, product developers, or business managers.