Role of substrate quality on the performance of semipolar (11 2 - 2) InGaN light-emitting diodes

We compare the optical properties and device performance of unpackaged InGaN/GaN multiple-quantum-well light-emitting diodes (LEDs) emitting at ∼430 nm grown simultaneously on a high-cost small-size bulk semipolar (11 2 - 2) GaN substrate (Bulk-GaN) and a low-cost large-size (11 2 - 2) GaN template created on patterned (10 1 - 2) r-plane sapphire substrate (PSS-GaN). The Bulk-GaN substrate has the threading dislocation density (TDD) of ∼ and basal-plane stacking fault (BSF) density of 0 cm-1, while the PSS-GaN substrate has the TDD of ∼2 × 108cm-2 and BSF density of ∼1 × 103cm-1. Despite an enhanced light extraction efficiency, the LED grown on PSS-GaN has two-times lower internal quantum efficiency than the LED grown on Bulk-GaN as determined by photoluminescence measurements. The LED grown on PSS-GaN substrate also has about two-times lower output power compared to the LED grown on Bulk-GaN substrate. This lower output power was attributed to the higher TDD and BSF density.

Localização em espaços interiores por luz visível para robôs móveis

Esta dissertação investiga a localização em espaços interiores através da comunicação por luz visível para robôs móveis, com base nos LEDs fixos nos edifícios, dando particular atenção à simulação e desenho do sensor, com vista ao desenvolvimento de um sensor de localização. Explica-se o crescimento da tecnologia LED e da constante necessidade de localização do homem em espaços interiores. Apresentado algumas características do LED e dos foto-detetores existentes. Com uma breve referencia a algumas das comunicações por luz visível de baixo débito possíveis de implementar. O desenvolvimento do protótipo do sensor inicia-se, principalmente, pela simulação de alguns dispositivos essenciais e das suas caraterísticas, como o emissor LED no controlo do ^angulo de meia potência (HPA) e a altura a que se encontra, e no recetor foto-díodo e a sua restrição de campo de visão (FOV). Simula-se o sensor pretendido com o número de foto-díodos necessários otimizando o espaço físico disponível e fazendo não só um refinamento no FOV mas também na distribuição espacial dos foto-díodos com funções predefinidas para a redução de incertezas de decisão de localização do robô. Estes resultados permitiram a construção física do sensor, desde o suporte para os foto-díodos, tendo em conta todas as medidas durante as simulações, e terminando com o desenvolvimento dos sensores e a sua integração completa. O tratamento de dados da leitura dos sinais recebidos do sensor são tratados por um microcontrolador, permitindo calcular parâmetros fundamentais no cálculo da posição. No final, os resultados teóricos bem como os práticos obtidos ao longo do desenvolvimento e possíveis propostas para trabalhos futuros que beneficiam desta investigação

Iluminação em ambientes fabris: otimização e análise técnica-e-económica

Esta Dissertação aborda a temática da eficiência energética em sistemas de iluminação fabris. Desde os primórdios da história da humanidade que a iluminação tem representado um papel importante. Não só garante condições de segurança, como começou por ser o intuito primordial das fogueiras pré-históricas, traduzindo-se num elemento de conforto. Atualmente seria impensável conceber as mais diversas atividades económicas e produtivas de um país sem iluminação. Nesse sentido a iluminação representa também um elemento fomentador de produtividade. Não é bem conhecido o impacto que a iluminação tem nos custos operacionais de uma unidade fabril. Principalmente por ser difícil de quantificar separadamente na fatura de eletricidade qual a percentagem correspondente à iluminação. Tipicamente estes custos podem ascender a 20% do orçamento global da autarquia em países desenvolvidos. Por esse motivo, o sector da iluminação tem investido esforço no sentido de promover melhores soluções de iluminação capazes de por um lado de satisfazer os requisitos do espaço a iluminar, e por outro propiciar soluções eficientes do ponto de vista energético. Estas soluções assentam essencialmente no uso de dispositivos mais eficientes (como por exemplo os LED´s ou as lâmpadas compactas fluorescentes) bem como em estratégias de controlo eficientes baseadas em dados sensoriais (como por exemplo deteção de movimento/presença). A combinação destas estratégias permite reduzir os consumos em cerca de 80% quando comparadas com soluções passivas. A empresa Amorim Cork Research Lda. é uma empresa prestadora de serviços ao universo das empresas da Corticeira Amorim, uma das maiores multinacionais de origem portuguesa. Teve origem no negócio da cortiça, em 1870, sendo hoje líder destacada no sector a nível mundial. Dada a dimensão da empresa e a sua subdivisão em várias Unidades Industriais com requisitos individuais, será expectável que a iluminação represente uma parte significativa da fatura de eletricidade. Atualmente, os vários setores encontram-se equipados com soluções de iluminação diferentes, na sua maioria empregando tecnologias passivas, noutros casos com dispositivos eficientes. Há algum interesse em migrar para soluções mais eficientes, em parte suportadas em DALI (com interface de comunicação PLC ou Zigbee).

Titanium dioxide based nanomaterials for photocatalytic water treatment

Water treatment using photocatalysis has gained extensive attention in recent years. Photocatalysis is promising technology from green chemistry point of view. The most widely studied and used photocatalyst for decomposition of pollutants in water under ultraviolet irradiation is TiO2 because it is not toxic, relatively cheap and highly active in various reactions. Within this thesis unmodified and modified TiO2 materials (powders and thin films) were prepared. Physico-chemical properties of photocatalytic materials were characterized with UV-visible spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectrometry (XPS), inductively coupled plasma optical emission spectroscopy (ICP-OES), ellipsometry, time-of-flight secondary ion mass spectrometry (ToF-SIMS), Raman spectroscopy, goniometry, diffuse reflectance measurements, thermogravimetric analysis (TGA) and nitrogen adsorption/desorption. Photocatalytic activity of prepared samples in aqueous environment was tested using model compounds such as phenol, formic acid and metazachlor. Also purification of real pulp and paper wastewater effluent was studied. Concentration of chosen pollutants was measured with high pressure liquid chromatography (HPLC). Mineralization and oxidation of organic contaminants were monitored with total organic carbon (TOC) and chemical oxygen demand (COD) analysis. Titanium dioxide powders prepared via sol-gel method and doped with dysprosium and praseodymium were photocatalytically active for decomposition of metazachlor. The highest degradation rate of metazachlor was observed when Pr-TiO2 treated at 450ºC (8h) was used. The photocatalytic LED-based treatment of wastewater effluent from plywood mill using commercially available TiO2 was demonstrated to be promising post-treatment method (72% of COD and 60% of TOC was decreased after 60 min of irradiation). The TiO2 coatings prepared by atomic layer deposition technique on aluminium foam were photocatalytically active for degradation of formic and phenol, however suppression of activity was observed. Photocatalytic activity of TiO2/SiO2 films doped with gold bipyramid-like nanoparticles was about two times higher than reference, which was not the case when gold nanospheres were used.

Postharvest light treatments increase skin blush in mango fruit

Skin colour is an important quality parameter that influences mango fruit marketability. The mango industry is interested in controlled induction of skin blush in mangoes. It is desirable to understand the control of anthocyanin accumulation in mango skin. Among environmental factors known to induce anthocyanin accumulation in plants, light is the most studied. Light exposure induces pigmentation in various fruits, including apple, strawberry and grape. The effect of different light qualities on skin blush in mango fruit has received relatively little attention. The objective of this study was to assess anthocyanin accumulation and blush in response to blue, red and far red light from light-emitting diodes (LEDs) as applied to harvested mango fruit skin during storage at 12°C. Except for red light, the other wavelengths induced anthocyanin accumulation and skin blush as compared to the dark control treatment. Anthocyanin concentration and a∗ values were highest in blue light exposed fruit skin. This wavelength enhanced phenylalanine ammonia lyase activity in the mango skin, which may be associated with increased pigmentation. LED light treatment did not affect other fruit quality parameters at 21 days of storage, including firmness, total soluble solids and titratable acidity. Overall, the findings suggest that postharvest treatment with blue light can induce skin blush in mango fruit, which potentially may enhance their commercial value.

COMPREHENSIVE ELECTRICAL/OPTICAL/THERMAL CHARACTERIZATIONS OF HIGH POWER LIGHT EMITTING DIODES AND LASER DIODES

Thermal characterizations of high power light emitting diodes (LEDs) and laser diodes (LDs) are one of the most critical issues to achieve optimal performance such as center wavelength, spectrum, power efficiency, and reliability. Unique electrical/optical/thermal characterizations are proposed to analyze the complex thermal issues of high power LEDs and LDs. First, an advanced inverse approach, based on the transient junction temperature behavior, is proposed and implemented to quantify the resistance of the die-attach thermal interface (DTI) in high power LEDs. A hybrid analytical/numerical model is utilized to determine an approximate transient junction temperature behavior, which is governed predominantly by the resistance of the DTI. Then, an accurate value of the resistance of the DTI is determined inversely from the experimental data over the predetermined transient time domain using numerical modeling. Secondly, the effect of junction temperature on heat dissipation of high power LEDs is investigated. The theoretical aspect of junction temperature dependency of two major parameters – the forward voltage and the radiant flux – on heat dissipation is reviewed. Actual measurements of the heat dissipation over a wide range of junction temperatures are followed to quantify the effect of the parameters using commercially available LEDs. An empirical model of heat dissipation is proposed for applications in practice. Finally, a hybrid experimental/numerical method is proposed to predict the junction temperature distribution of a high power LD bar. A commercial water-cooled LD bar is used to present the proposed method. A unique experimental setup is developed and implemented to measure the average junction temperatures of the LD bar. After measuring the heat dissipation of the LD bar, the effective heat transfer coefficient of the cooling system is determined inversely. The characterized properties are used to predict the junction temperature distribution over the LD bar under high operating currents. The results are presented in conjunction with the wall-plug efficiency and the center wavelength shift.

Mastering heterostructured colloidal nanocrystal properties for light-emitting diodes and solar cells

Solution-grown colloidal nanocrystal (NC) materials represent ideal candidates for optoelectronic devices, due to the flexibility with which they can be synthesized, the ease with which they can be processed for devicefabrication purposes and, foremost, for their excellent and size-dependent tunable optical properties, such as high photoluminescence (PL) quantum yield, color purity, and broad absorption spectra up to the near infrared. The advent of surfactant-assisted synthesis of thermodynamically stable colloidal solutions of NCs has led to peerless results in terms of uniform size distribution, composition, rational shape-design and the possibility of building heterostructured NCs (HNCs) comprising two or more different materials joined together. By tailoring the composition, shape and size of each component, HNCs with gradually higher levels of complexity have been conceived and realized, which are endowed with outstanding characteristics and optoelectronic properties. In this review, we discuss recent advances in the design of HNCs for efficient light-emitting diodes (LEDs) and photovoltaic (PV) solar cell devices. In particular, we will focus on the materials required to obtain superior optoelectronic quality and efficient devices, as well as their preparation and processing potential and limitations

Contactless Spectral-Dependent Measurement of Bulk Lifetime and Surface Recombination Velocity in Silicon Photovoltaic Materials

Charge carrier lifetime measurements in bulk or unfinished photovoltaic (PV) materials allow for a more accurate estimate of power conversion efficiency in completed solar cells. In this work, carrier lifetimes in PV- grade silicon wafers are obtained by way of quasi-steady state photoconductance measurements. These measurements use a contactless RF system coupled with varying narrow spectrum input LEDs, ranging in wavelength from 460 nm to 1030 nm. Spectral dependent lifetime measurements allow for determination of bulk and surface properties of the material, including the intrinsic bulk lifetime and the surface recombination velocity. The effective lifetimes are fit to an analytical physics-based model to determine the desired parameters. Passivated and non-passivated samples are both studied and are shown to have good agreement with the theoretical model.

Optical Wireless Communication for Mobile Platforms

The past few decades have witnessed the widespread adaptation of wireless devices such as cellular phones and Wifi-connected laptops, and demand for wireless communication is expected to continue to increase. Though radio frequency (RF) communication has traditionally dominated in this application space, recent decades have seen an increasing interest in the use of optical wireless (OW) communication to supplement RF communications. In contrast to RF communication technology, OW systems offer the use of largely unregulated electromagnetic spectrum and large bandwidths for communication. They also offer the potential to be highly secure against jamming and eavesdropping. Interest in OW has become especially keen in light of the maturation of light-emitting diode (LED) technology. This maturation, and the consequent emerging ubiquity of LED technology in lighting systems, has motivated the exploration of LEDs for wireless communication purposes in a wide variety of applications. Recent interest in this field has largely focused on the potential for indoor local area networks (LANs) to be realized with increasingly common LED-based lighting systems. We envision the use of LED-based OW to serve as a supplement to RF technology in communication between mobile platforms, which may include automobiles, robots, or unmanned aerial vehicles (UAVs). OW technology may be especially useful in what are known as RF-denied environments, in which RF communication may be prohibited or undesirable. The use of OW in these settings presents major challenges. In contrast to many RF systems, OWsystems that operate at ranges beyond a few meters typically require relatively precise alignment. For example, some laser-based optical wireless communication systems require alignment precision to within small fractions of a degree. This level of alignment precision can be difficult to maintain between mobile platforms. Additionally, the use of OW systems in outdoor settings presents the challenge of interference from ambient light, which can be much brighter than any LED transmitter. This thesis addresses these challenges to the use of LED-based communication between mobile platforms. We propose and analyze a dual-link LED-based system that uses one link with a wide transmission beam and relaxed alignment constraints to support a more narrow, precisely aligned, higher-data-rate link. The use of an optical link with relaxed alignment constraints to support the alignment of a more precisely aligned link motivates our exploration of a panoramic imaging receiver for estimating the range and bearing of neighboring nodes. The precision of such a system is analyzed and an experimental system is realized. Finally, we present an experimental prototype of a self-aligning LED-based link.

High bandwidth freestanding semipolar (11–22) InGaN/GaN light-emitting diodes

Freestanding semipolar (11–22) indium gallium nitride (InGaN) multiplequantum-well light-emitting diodes (LEDs) emitting at 445 nm have been realized by the use of laser lift-off (LLO) of the LEDs from a 50- m-thick GaN layer grown on a patterned (10–12) r -plane sapphire substrate (PSS). The GaN grooves originating from the growth on PSS were removed by chemical mechanical polishing. The 300 m × 300 m LEDs showed a turn-on voltage of 3.6 V and an output power through the smooth substrate of 0.87 mW at 20 mA. The electroluminescence spectrum of LEDs before and after LLO showed a stronger emission intensity along the [11–23]InGaN/GaN direction. The polarization anisotropy is independent of the GaN grooves, with a measured value of 0.14. The bandwidth of the LEDs is in excess of 150 MHz at 20 mA, and back-to-back transmission of 300 Mbps is demonstrated, making these devices suitable for visible light communication (VLC) applications.

Reforestation challenges in Scandinavia

In the keynote, major reforestation challenges in Scandinavia will be highlighted. The following countries make up Scandinavia: Iceland, Norway, Sweden, Finland and Denmark. For Iceland, with only a forest cover of 2%, a major reforestation challenge is the deforestation and overgrazing in combination with land degradation and extensive soil erosion. The challenges include the conflicts with livestock farmers. For centuries the commons were used for sheep and horse grazing. However, more and more of farmer grazing land have been fenced up, allowing the regeneration of birch and plantations of other species to increase. With a forest cover of 37% and 69% respectively, for decades a major reforestation challenge in Norway and Sweden has been the risk of seedling damages from the pine weevil. Unprotected seedlings can have a survival rate of less than 25% after being planted. Pine weevils feed on the bark of planted young seedlings at regeneration sites. If the seedling is girdled, it will not survive. In Sweden, and soon in Norway, pesticides have been forbidden. In the keynote, new methods and technology will be presented based on non-chemical protection. In Finland, with a forest cover of 75%, a major reforestation challenge is linked to the forest structure. The structure of Finnish forestry includes many private forests in combination with small regeneration sites. This implies a situation where logistics and methods for lifting and field storage provide a major challenge in order to preserve seedling quality until the planting date. Due to this situation, new logistic systems and technologies are being developed in Finland, including new seedling cultivation programs (including cultivation under Light Emitting Diodes (LEDs)) to match the access of fresh planting stock to different planting dates. In Denmark, with a forest cover of 13%, a major reforestation challenge is the possibility of future plantations based on a wide range of relevant species. For this to become a realistic option, new methods and technology have to be developed in reforestation activities that support this possibility. These methods and technology should make it possible to not be limited to certain species due to problems and restrictions during field establishment. This due to the prospect of establishing stable, healthy, and productive stands of various forest species that can be adapted to future climate change.