Utilização de descarte de resíduos têxtil (poliamida/poliester), como agregado, em concreto

Neste trabalho são apresentadas algumas características físicas, vantagens e viabilidade do uso do pó de tecido, proveniente do processamento de resíduos têxteis que são descartados em confecções em geral. A produção e utilização desse tipo de pó diminui o impacto ambiental e se mostra viável economicamente, pois é produzido facilmente a partir do processamento de resíduos, que seriam descartados na natureza. O presente trabalho mostra o estudo da produção do pó de tecido e a sua substituição parcial do agregado miúdo natural na produção de concretos de cimento Portland convencionais. Para comprovar a viabilidade técnica e econômica do uso do pó de tecido foram analisadas características do agregado como sua composição granulométrica, e seu comportamento nos ensaios de abatimento tronco de cone (Slump Test). Uma relação água-cimento também foi convencionada a um concreto usual com resistência esperada de 27MPa. Com estes dados foi definido um traço para o concreto utilizando 5% e 15% de agregado pó de tecido, substituindo a areia. A pesquisa apresenta os resultados de resistência à compressão simples dos corpos de prova cilíndricos de concreto aos 28 dias. Verificou-se que as amostras não apresentaram diferenças significativas de resistência entre si, tão pouco com relação às resistências de um concreto convencional produzido somente com agregado miúdo natural. Entretanto, houve uma melhora nos resultados dos ensaios à compressão, principalmente no concreto com 15% de pó de tecido.

Anatomia do Lenho de espécies da subfamília Ixoroideae (Rubiaceae) do Parque Estadual da Ilha Grande, Rio de Janeiro

Os estudos anatômicos do lenho são frequentemente aplicados à solução de questões taxonômicas, filogenéticas e evolutivas, visto que este tecido apresenta uma tendência mais conservadora e, consequentemente, menor plasticidade. Este trabalho tem por objetivo o estudo da estrutura anatômica do lenho de oito espécies arbustiva-arbóreas da subfamília Ixoroideae ocorrente no Parque Estadual da Ilha Grande, Angra dos Reis-RJ, visando contribuir com subsídios à identificação local das espécies e à taxonomia e filogenia da subfamília Ixoroideae e da família Rubiaceae. O estudo foi desenvolvido em um importante remanescente do bioma Mata Atlântica no estado do Rio de Janeiro. O material botânico foi coletado por métodos não destrutivo, as amostras foram processadas segundo técnicas usuais em anatomia da madeira e as análises e descrições seguiram as recomendações da COPANT (1973) e IAWA Commitee (1989). Os resultados demonstraram que as oito espécies estudadas apresentam características qualitativas diagnósticas que permitiram segregar as espécies e construir uma chave de identificação com base na presença ou ausência de inclusões inorgânicas, paredes celulares disjuntivas, células envolventes nos raios e no tipo de parênquima axial. As análises estatísticas realizadas sustentaram o agrupamento das espécies estudadas na subfamília Ixoroideae, porém não foi possível o agrupamento em nível das tribos às quais estas espécies estão subordinadas. Os resultados indicaram ainda a necessidade de reanálise das árvores filogenéticas hipotéticas propostas para subfamília Ixoroideae, com base nos tipos de lenho, de inclusões minerais e de parênquima axial. Cabe ainda destacar que os resultados obtidos corroboraram a importância da anatomia do lenho para a identificação de espécies de difícil reconhecimento na família Rubiaceae. Esses dados são úteis especialmente na ausência de material reprodutivo, o que representa importante aspecto para o gerenciamento e manejo das espécies nativas da Unidade de Conservação onde este estudo foi realizado

Efficient carbon nanotube field emitter using electrospun carbon nanofibers as a flexible electrode

Thermal-stable, conductive, and flexible carbon fabric (CF), which is composed of thin carbon fibers prepared by electrospinning, was used for the substrate of carbon nanotube (CNT) field emitter arrays. The field emitter arrays were prepared by chemical vapor deposition (CVD). The current density-electric field characteristics revealed that the CNT field emitter arrays on CF produced a higher current density at a lower turn-on voltage compared to ones on a Si substrate. This emitter integrated with a gate electrode based on hierarchy-structured carbon materials, CNTs on CF, can be used for light sources, displays, and other electronic devices. © 2009 Materials Research Society.

Development and experimental validation of a mathematical model for friction between fabrics and a volar forearm phantom.

An analytical mathematical model for friction between a fabric strip and the volar forearm has been developed and validated experimentally. The model generalizes the common assumption of a cylindrical arm to any convex prism, and makes predictions for pressure and tension based on Amontons' law. This includes a relationship between the coefficient of static friction (mu) and forces on either end of a fabric strip in contact with part of the surface of the arm and perpendicular to its axis. Coefficients of friction were determined from experiments between arm phantoms of circular and elliptical cross-section (made from Plaster of Paris covered in Neoprene) and a nonwoven fabric. As predicted by the model, all values of mu calculated from experimental results agreed within +/- 8 per cent, and showed very little systematic variation with the deadweight, geometry, or arc of contact used. With an appropriate choice of coordinates the relationship predicted by this model for forces on either end of a fabric strip reduces to the prediction from the common model for circular arms. This helps to explain the surprisingly accurate values of mu obtained by applying the cylindrical model to experimental data on real arms.

Development and validation of a new method for measuring friction between skin and nonwoven materials.

A new method for measuring the coefficient of friction between nonwoven materials and the curved surface of the volar forearm has been developed and validated. The method was used to measure the coefficient of static friction for three different nonwoven materials on the normal (dry) and over-hydrated volar forearms of five female volunteers (ages 18-44). The method proved simple to run and had good repeatability: the coefficient of variation (standard deviation expressed as a percentage of the mean) for triplets of repeat measurements was usually (80 per cent of the time) less than 10 per cent. Measurements involving the geometrically simpler configuration of pulling a weighted fabric sample horizontally across a quasi-planar area of volar forearm skin proved experimentally more difficult and had poorer repeatability. However, correlations between values of coefficient of static friction derived using the two methods were good (R = 0.81 for normal (dry) skin, and 0.91 for over-hydrated skin). Measurements of the coefficient of static friction for the three nonwovens for normal (dry) and for over-hydrated skin varied in the ranges of about 0.3-0.5 and 0.9-1.3, respectively. In agreement with Amontons' law, coefficients of friction were invariant with normal pressure over the entire experimental range (0.1-8.2 kPa).

Assessment and monitoring of marine debris in Gray's Reef National Marine Sanctuary

Gray’s Reef National Marine Sanctuary (GRNMS) is located 32.4 km offshore of Sapelo Island, Georgia. The ecological importance of this area is related to the transition between tropical and temperate waters, and the existence of a topographically complex system of ledges. Due to its central location, GRNMS can be used as a focal site to study the accumulation and impacts of marine debris on the Atlantic continental shelf offshore of the Southeast United States. Previously, researchers characterized marine debris in GRNMS and reported that incidence of the debris at the limited densely colonized ledge sites was significantly greater than at sand or sparsely colonized live bottom, and is further influenced by the level of boating activity and physiographic characteristics (e.g., ledge height). Information gleaned from the initial marine debris characterization was used to devise a strategy for prioritizing cleanup and monitoring efforts. However, a significant gap in knowledge was the rate of debris accumulation. The primary objective of this study was to select, mark, and perform initial marine debris surveys at permanent monitoring sites within GRNMS to quantify long-term trends in types, abundance, impacts, and accumulation rates of debris. Ledge sites were selected to compare types, abundance, and accumulation rates of marine debris between a) areas of high and low use and b) short and tall ledges. Nine permanent monitoring sites were marked and initially surveyed in 2007/2008. Surveys were conducted within a 50 x 4 m transect for a total survey area of 200 square meters. All debris was removed and detailed information was taken on the types of debris, quantity, and associations with benthic fauna. Information on associations with benthic fauna included degree of entanglement, type of organism with which it is entangled or resting on, degree of fouling, and visible impacts such as tissue abrasions. Sites were re-surveyed approximately one year later to quantify new accumulation. During the initial survey, a total of ten debris items, totaling 16.3 kg in weight, were removed from two monitoring stations, both “tall” sites within the area of high boat use. Year-one accumulation totaled five items and approximately 7 kg in weight. Similar to the initial survey, all debris was found at sites in the area of high boat use. However, in contrast to the initial survey, two of these items were found on medium-height ledges. Removed items included fishing line, leaders, rope, plastic, and fabric. Although items were often encrusted in benthic biota or entangled on the ledge, impacts such as abrasions or other injuries were not observed. During the 2009 monitoring efforts, volunteer divers were trained to conduct the survey. Monitoring protocols were documented for GRNMS staff and included as an appendix of this report to enable long-term monitoring of sites. Additionally, national reconnaissance data (e.g. satellite, radar, aerial surveys) and other information on known fishing locations were examined for patterns of resource use and correlations with debris occurrence patterns. A previous model predicting the density of marine debris based on ledge features and boat use was refined and the results were used to generate a map of predicted debris density for all ledges.

SOME MEASUREMENTS OF THE PERMEABILITY OF KAOLIN.

This paper reports an experimental investigation of the vertical and horizontal permeabilities of speswhite kaolin clay. The permeabilities were measured using falling head permeability tests. A modification to a conventional oedometer was devised so that either vertical or horizontal permeabilities could be determined. It was found that the vertical and horizontal permeabilities of the clay slurry were similar, but that as the clay was consolidated one dimensionally the anisotropy of the clay fabric resulted in a greater horizontal permeability than the vertical permeability at any void ratio. Both permeabilities were uniquely related to the void ratio.

A decoupled whole-building simulation engine for rapid exhaustive search of low-carbon and low-energy building refurbishment options

This paper presents the development of a new building physics and energy supply systems simulation platform. It has been adapted from both existing commercial models and empirical works, but designed to provide expedient exhaustive simulation of all salient types of energy- and carbon-reducing retrofit options. These options may include any combination of behavioural measures, building fabric and equipment upgrades, improved HVAC control strategies, or novel low-carbon energy supply technologies. We provide a methodological description of the proposed model, followed by two illustrative case studies of the tool when used to investigate retrofit options of a mixed-use office building and primary school in the UK. It is not the intention of this paper, nor would it be feasible, to provide a complete engineering decomposition of the proposed model, describing all calculation processes in detail. Instead, this paper concentrates on presenting the particular engineering aspects of the model which steer away from conventional practise. © 2011 Elsevier Ltd.

Engineering as a tool for improving human habitat

The conventional approaches to poverty alleviation in the slums entail a cocktail of interventions in health, education, governance and physical improvements, often stretching the scarce resources far and thin. Driven by the 'poverty' mindset, physical measures such as minimal paving, public water posts and community latrines actually brand the slums apart instead of assimilating them into the urban infrastructure fabric. The concept of Slum Networking proposes comprehensive water and environmental sanitation infrastructure as the central and catalytic leverage for holistic development. At costs less than the conventional 'slum' solutions, it tries to penetrate a high quality urban infrastructure net deeply into the slums to assimilate them into the city rather than lock them in as disadvantaged islands. Further, it transcends resource barriers and 'aid' through innovative partnerships and the latent resource mobilisation potential of the so-called 'poor'. This paper examines Slum Networking as implemented in Sanjaynagar in Ahmedabad, India and compares it with a similar settlement with no interventions in Ahmedabad. It assesses the knock-on impact of physical infrastructure on health, education and poverty. Finally, it evaluates the multiplier effect of physical infrastructure and the partnerships on the subsequent investments by the community in its own shelter and habitat. Copyright © 2009 Inderscience Enterprises Ltd.

Free-space optoelectronic switching cores with MPLS for SANs over WDM ring networks

With increasing demands on storage devices in the modern communication environment, the storage area network (SAN) has evolved to provide a direct connection allowing these storage devices to be accessed efficiently. To optimize the performance of a SAN, a three-stage hybrid electronic/optical switching node architecture based on the concept of a MPLS label switching mechanism, aimed at serving as a multi-protocol label switching (MPLS) ingress label edge router (LER) for a SAN-enabled application, has been designed. New shutter-based free-space multi-channel optical switching cores are employed as the core switch fabric to solve the packet contention and switching path conflict problems. The system-level node architecture design constraints are evaluated through self-similar traffic sourced from real gigabit Ethernet network traces and storage systems. The extension performance of a SAN over a proposed WDM ring network, aimed at serving as an MPLS-enabled transport network, is also presented and demonstrated. © 2012 OSA.

The night purging of a two-storey atrium building

We examine the fluid mechanics of night purging in a two-storey naturally ventilated atrium building. We develop a mathematical model of a simplified atrium building and focus on the rate at which warm air purges from each storey and the atrium by displacement ventilation into a still cool night environment of a constant temperature. To develop a first insight into how the geometry of the building influences the rate at which warm air purges from each storey via the atrium we neglect heat exchange with the fabric (so there is no thermal buffering) and furthermore assume that the warm air layers in each storey and the atrium are of uniform temperature. The plumes of warm air that rise from the storeys into the atrium, causing the atrium to fill with warm air, have a very strong influence on the night purge. Modelling these as axisymmetric turbulent plumes, we identify three forms of purging behaviour. Each purge is characterised by five key times identified in the progression of the night purge and physical rationale for these differing behaviours is given. An interface velocity deficit and volumetric purge deficit are introduced as measures of the efficiency of a night purge. © 2010 Elsevier Ltd.

Future-proofed energy design for dwellings: Case studies from England and application to the Code for Sustainable Homes

This paper investigates 'future-proofing' as an unexplored yet all-important aspect in the design of low-energy dwellings. It refers particularly to adopting lifecycle thinking and accommodating risks and uncertainties in the selection of fabric energy efficiency measures and low or zero-carbon technologies. Based on a conceptual framework for future-proofed design, the paper first presents results from the analysis of two 'best practice' housing developments in England; i.e., North West Cambridge in Cambridge and West Carclaze and Baal in St. Austell, Cornwall. Second, it examines the 'Energy and CO2 Emissions' part of the Code for Sustainable Homes to reveal which design criteria and assessment methods can be practically integrated into this established building certification scheme so that it can become more dynamic and future-oriented.Practical application: Future-proofed construction is promoted implicitly within the increasingly stringent building regulations; however, there is no comprehensive method to readily incorporate futures thinking into the energy design of buildings. This study has a three-fold objective of relevance to the building industry:Illuminating the two key categories of long-term impacts in buildings, which are often erroneously treated interchangeably:- The environmental impact of buildings due to their long lifecycles.- The environment's impacts on buildings due to risks and uncertainties affecting the energy consumption by at least 2050. This refers to social, technological, economic, environmental and regulatory (predictable or unknown) trends and drivers of change, such as climate uncertainty, home-working, technology readiness etc.Encouraging future-proofing from an early planning stage to reduce the likelihood of a prematurely obsolete building design.Enhancing established building energy assessment methods (certification, modelling or audit tools) by integrating a set of future-oriented criteria into their methodologies. © 2012 The Chartered Institution of Building Services Engineers.

生态恢复后的千烟洲植物群落种类组成及结构特征

Qianyanzhou(QYZ) Ecological Station established in 1983 with an area of 204 hm~2 is affiliated to the Chinese Ecosystem Research Network.Before 1982,herbs had been dominant,sparsely dotted with shrubs.After 20-year restoration of the vegetation,the vegetation showed significant changes in both forest coverage and species diversity.Forest coverage had increased to 93.3% in 1999 from 0.4% in 1982.The vegetation could be broadly classified into two groups: artificial forest,accounting for the most percent,and natural secondary forest.These two groups could be subdivided into 12 types.Based on the 2003 field work,The authors studied plant community composition and vertical structure.The results were as follows: 1) On the study plots were there about 150 species,of which 100,49,and 47 grew in arbor layer and shrub layer and herb layer,respectively.Of 12 community types,the amount of species in shrub layer was larger than that of other two layers.As to the species richness in the different community types,Liquidambar formosana community showed the highest and Imperata cylindrical var.major community the least.The amount of species in arbor layer of artificial forest was smaller than those of natural Pinus massoniana forest,but no difference in understory.2) Loropetalum chinense,Quercus fabric and Vaccinium bracteatum were dominant shrub species with a wide distribution.Three ferns Woodwardia japonica、Dryopteris atrata and Dicrannepteris dichotoma were dominant herb species.Lianas were sparse,but Milletlia reticulata were found in all forest types.3) Up to now some natural regeneration species,such as Eurya muricata、Quercus fabri、Vaccinium bracteatum、Rhus chinensis、Adinandra bockiana,had grown in the arbor layer of artificial forests.Some herb species,such as Arundinella setosa、Miscanthus floridulus、Isachne globosa、Scirpus triqueter,which were dominant ones in the herb layer before the restoration of vegetation,disappeared now.4) The vertical structure of natural Pinus massoniana community and Liquidambar formosana community showed more complex comparing with artificial forests.For the artificial forests,the conifer and broad-leaves mixed forest had a more complex structure.In both natural Pinus(massoniana) community and Liquidambar formosana community,it was dominated by individuals with height of 3～4 m,while 10～12 m in the artificial forests.

Fabrication of Superhydrophobic Cellulose-Based Materials through a Solution-Immersion Process

An industrial waterproof reagent [(potassium methyl siliconate) (PMS)] was used for fabricating a superhydrophobic surface on a cellulose-based material (cotton fabric or paper) through a solution-immersion method. This method involves a hydrogen bond assembly and a polycondensation process. The silanol, which was formed by a reaction of PMS aqueous solution with CO2, Was assembled on the cellulose molecule surface via hydrogen bond interactions. The polymethylsilsesquioxane coatings were prepared by a polycondensation reaction of the hydroxyl between cellulose and silatiol. The superhydrophobic cellulose materials were characterized by FTIR spectroscopy, thermogravimetry, and surface analysis (XPS, FESEM, AFM, and contact angle measurements).