Thermal conductivity of a new carbon nanotube analog: The diamond nanothread

Based on the non-equilibrium molecular dynamics simulations, we have studied the thermal conductivities of a novel ultra-thin one-dimensional carbon nanomaterial - diamond nanothread (DNT). Unlike single-wall carbon nanotube (CNT), the existence of the Stone-Wales transformations in DNT endows it with richer thermal transport characteristics. There is a transition from wave-dominated to particle-dominated transport region, which depends on the length of poly-benzene rings. However, independent of the transport region, strong length dependence in thermal conductivity is observed in DNTs with different lengths of poly-benzene ring. The distinctive SW characteristic in DNT provides more degrees of freedom to tune the thermal conductivity not found in the homogeneous structure of CNT. Therefore, DNT is an ideal platform to investigate various thermal transport mechanisms at the nanoscale. Its high tunability raises the potential to design DNTs for different applications, such as thermal connection and temperature management.

Composition-controlled metal-insulator transitions and minimum metallic conductivity in the oxide systems LaNi1-xMxO3 (M = Cr, Mn, Fe, or Co)

The composition-controlled metal-insulator transition in the perovskite systems LaNi1-xMxO3 (M = Cr, Mn, Fe, and Co) has been investigated by transport measurements over the temperature range 12-300 K. These systems, which have critical electron densities (nc) in the range (1-2) -1020 electrons cm-3, exhibit sharp metal-insulator transitions at the base temperature. The corresponding minimum metallic conductivity (Ï-min), separating the localized and itinerant electronic regimes, is of the order of 102 ohm-1 cm-1. Particular attention is paid to the idea of Ï-min scaling with nc, and our present results are compared with earlier studies of the metal-insulator transition in low (e.g., Ge:Sb) and high (e.g., metal-ammonia, supercritical Hg) electron-density systems. A link is established between the transport and magnetic properties of the title systems at the metal-insulator transition.

The effect of composition, electron irradiation and quenching on ionic conductivity in a new solid polymer electrolyte: (PEG) (x) NH4I

We have prepared, characterized and investigated a new PEG-2000 based solid polymer electrolyte (PEG) x NH4I. Ionic conductivity measurements have been made as a function of salt concentration as well as temperature in the range 265–330 K. Selected compositions of the electrolyte were exposed to a beam of 8 MeV electrons to an accumulated dose of 10 kGy to study the effect on ionic conductivity. The electrolyte samples were also quenched at liquid nitrogen temperature and conductivity measurements were made. The ionic conductivity at room temperature exhibits a characteristic double peak for the composition x = 20 and 70. Both electron beam irradiation and quenching at low temperature have resulted in an increase in conductivity by 1–2 orders of magnitude. The enhancement of conductivity upon irradiation and quenching is interpreted as due to an increase in amorphous region and decrease in crystallinity of the electrolyte. DSC and proton NMR measurements also support this conclusion.

Laboratory investigation on the effects of overburden pressure, water, and time on slaking induced material property degradation of coal mine spoil

In open-cut strip mining, waste material is placed in-pit to minimise operational mine costs. Slope failures in these spoil piles pose a significant safety risk to personnel, along with a financial risk from loss of equipment and scheduling delays. It has been observed that most spoil pile failures occur when the pit has been previously filled with water and then subsequently dewatered. The failures are often initiated at the base of spoil piles where the material can undergo significant slaking (disintegration) over time due to overburden pressure and water saturation. It is important to understand how the mechanical properties of base spoil material are affected by slaking when designing safe spoil pile slope angles, heights, and dewatering rates. In this study, fresh spoil material collected from a coal mine in Brown Basin Coalfield of Queensland, Australia was subjected to high overburden pressure (0 – 900 kPa) under saturated condition and maintained over a period of time (0 – 6 months) allowing the material to slake. To create the above conditions, laboratory designed pressure chambers were used. Once a spoil sample was slaked under certain overburden pressure over a period of time, it was tested for classification, permeability, and strength properties. Results of this testing program suggested that the slaking of saturated coal mine spoil increase with overburden pressure and the time duration over which the overburden pressure was maintained. Further, it was observed that shear strength and permeability of spoil decreased with increase in spoil slaking.

Chemical bond approach to determining conductivity band gaps in amorphous chalcogenides and pnictides

The minimum energy required for the formation of conjugate pair of charged defects is found to be approximately equal to the experimental activation energy for d.c. conductivity in a number of amorphous chalcoganides and pnictides. This observation implies that the defect pair formation energy represents an intrinsic gap for transport in amorphous chalcogenides.

Climate change and human rights: Intellectual property challenges and opportunities

Mitigating and adapting to the effects of climate change will require innovation and the development of new technologies. Intellectual property laws have a key part to play in the global transfer of climate technologies. However, failures to properly utilize flexibilities in intellectual property regimes or comply with technology transfer obligations under international climate change agreements calls for a human rights based analysis of climate technology transfer. Climate change is an unprecedented challenge and requires unprecedented strategies. Given the substantial impact of climate change on all of humanity and the ethical imperative to act, a complete rethink of traditional intellectual property approaches is warranted. This report proposes a series of intellectual property law policy options, through a human rights framework, aimed at promoting access to technologies to reduce the human suffering caused by climate change.

Owning the new economy: A guide to intellectual property management for Australia's clean technology sector

Australia's history of developing and managing the intellectual property rights of domestic innovations is – at best – mixed. The relevant immaturity of Australia's public sector commercialisation infrastructure has, over recent decades, been the subject of both stinging academic commentary and not insubstantial juridical disbelief. That said, improvements have been observed, and increasingly, private sector involvement in public sector innovation has allowed for a deepening refinement of domestic approaches to IP retention and ongoing management. Rather than a bare critique of Australia's IP management track-record, or a call for specific law reform, this manual engages at a more practical level some of the foundational questions that ought be asked by entities involved in the 'cleantech' industries. Beginning simply at what is IP and why it matters, this manual examines the models of IP management available to market participants around the world. The process of IP management is defined and assessed through a commercial lens; assessing the 'pros' and 'cons' of each management choice with a view to equipping the reader to determine which approach may be best adapted to their given clean tech project. The manual concludes with a brief survey of alternative models of Intellectual Property management, including relevant examples from overseas and prominent suggestions arising out of the academic discourse. It appears inevitable that the global warming challenge will prompt specific legislative, regulatory and multi-lateral responses by nation states, however, the ultimate form of any such response remains a highly contested political and social issue. Accordingly, the structure of this manual, and the discussion points raised herein, seek introduce the reader to some of the more contentious debates occurring around the world at the intersection between IP and climate change.

Ultra-low conductivity noise in metallic nanowires

By modifying the electrodeposition technique, we have stabilized the silver nanowires (AgNWs) in high-energy hexagonal closed packed (hcp)structure. The conductivity noise measurements show that the noise magnitude in hcp silver nanowires is several orders of magnitude smaller than that of face centered cubic (fcc) silver nanowires, which is obtained by standard over potential lectrodeposition (OPD)technique. The reduction of noise can be attributed to the restricted dislocation dynamics in hcp AgNWs due to the presence of less number of slip systems. Temperature dependent noise measurements show that the noise magnitude in hcp AgNWs is weakly temperature dependent while in fcc AgNWs it is strong function of temperature.

Numerical studies of gypsum plasterboard and MGO board lined LSF walls exposed to fire

Fire resistance of cold-formed light gauge steel frame (LSF) wall systems is enhanced by lining them with single or multiple layers of wall boards with varying thermal properties. These wall boards are gypsum plasterboards or Magnesium Oxide (MgO) boards produced by different manufacturers. Thermal properties of these boards appear to show considerable variations and this can lead to varying fire resistance levels (FRL) for their wall systems. Currently FRLs of wall systems are determined using full scale fire tests, but they are time consuming and expensive. Recent research studies on the fire performance of LSF wall systems have used finite element studies to overcome this problem, but they were developed based on 1-D and 2-D finite element platform capable of performing either heat transfer or structural analysis separately. Hence in this research a 3-D finite element model was developed first for LSF walls lined with gypsum plasterboard and cavity insulation materials. Accurate thermal properties of these boards are essential for finite element modelling, and thus they were measured at both ambient and elevated temperatures. This experimental study included specific heat, relative density and thermal conductivity of boards. The developed 3-D finite element model was then validated using the available fire tests results of LSF walls lined with gypsum plasterboard, and is being used to investigate the fire performance of different LSF wall configurations. The tested MgO board exhibited significant variations in their thermal properties in comparison to gypsum plasterboards with about 50% loss of its initial mass at about 500 ºC compared to 16% for gypsum plasterboards. Hence the FRL of MgO board lined LSF wall systems is likely to be significantly reduced. This paper presents the details of this research study on the fire performance of LSF wall systems lined with gypsum plasterboard and MgO board including the developed 3-D finite element models, thermal property tests and the results.

Indigenous Intellectual Property: A Handbook of Contemporary Research

Taking an interdisciplinary approach unmatched by any other book on this topic, this thoughtful Handbook considers the international struggle to provide for proper and just protection of Indigenous intellectual property (IP). In light of the United Nations Declaration on the Rights of Indigenous Peoples 2007, expert contributors assess the legal and policy controversies over Indigenous knowledge in the fields of international law, copyright law, trademark law, patent law, trade secrets law, and cultural heritage. The overarching discussion examines national developments in Indigenous IP in the United States, Canada, South Africa, the European Union, Australia, New Zealand, and Indonesia. The Handbook provides a comprehensive overview of the historical origins of conflict over Indigenous knowledge, and examines new challenges to Indigenous IP from emerging developments in information technology, biotechnology, and climate change. Practitioners and scholars in the field of IP will learn a great deal from this Handbook about the issues and challenges that surround just protection of a variety of forms of IP for Indigenous communities. Preface The Legacy of David Unaipon Matthew Rimmer Introduction: Mapping Indigenous Intellectual Property Matthew Rimmer PART I INTERNATIONAL LAW 1. The United Nations Declaration on the Rights of Indigenous Peoples: A Human Rights Framework for Indigenous Intellectual Property Mauro Barelli 2. The WTO, The TRIPS Agreement and Traditional Knowledge Tania Voon 3. The World Intellectual Property Organization and Traditional Knowledge Sara Bannerman 4. The World Indigenous Network: Rio+20, Intellectual Property, Indigenous Knowledge, and Sustainable Development Matthew Rimmer PART II COPYRIGHT LAW AND RELATED RIGHTS 5. Government Man, Government Painting? David Malangi and the 1966 One-Dollar Note Stephen Gray 6. What Wandjuk Wanted Martin Hardie 7. Avatar Dreaming: Indigenous Cultural Protocols and Making Films Using Indigenous Content Terri Janke 8. The Australian Resale Royalty for Visual Artists: Indigenous Art and Social Justice Robert Dearn and Matthew Rimmer PART III TRADE MARK LAW AND RELATED RIGHTS 9. Indigenous Cultural Expression and Registered Designs Maree Sainsbury 10. The Indian Arts and Crafts Act: The Limits of Trademark Analogies Rebecca Tushnet 11. Protection of Traditional Cultural Expressions within the New Zealand Intellectual Property Framework: A Case Study of the Ka Mate Haka Sarah Rosanowski 12 Geographical Indications and Indigenous Intellectual Property William van Caenegem PART IV PATENT LAW AND RELATED RIGHTS 13. Pressuring ‘Suspect Orthodoxy’: Traditional Knowledge and the Patent System Chidi Oguamanam, 14. The Nagoya Protocol: Unfinished Business Remains Unfinished Achmad Gusman Siswandi 15. Legislating on Biopiracy in Europe: Too Little, too Late? Angela Daly 16. Intellectual Property, Indigenous Knowledge, and Climate Change Matthew Rimmer PART V PRIVACY LAW AND IDENTITY RIGHTS 17. Confidential Information and Anthropology: Indigenous Knowledge and the Digital Economy Sarah Holcombe 18. Indigenous Cultural Heritage in Australia: The Control of Living Heritages Judith Bannister 19. Dignity, Trust and Identity: Private Spheres and Indigenous Intellectual Property Bruce Baer Arnold 20. Racial Discrimination Laws as a Means of Protecting Collective Reputation and Identity David Rolph PART VI INDIGENOUS INTELLECTUAL PROPERTY: REGIONAL PERSPECTIVES 21. Diluted Control: A Critical Analysis of the WAI262 Report on Maori Traditional Knowledge and Culture Fleur Adcock 22. Traditional Knowledge Governance Challenges in Canada Jeremy de Beer and Daniel Dylan 23. Intellectual Property protection of Traditional Knowledge and Access to Knowledge in South Africa Caroline Ncube 24. Traditional Knowledge Sovereignty: The Fundamental Role of Customary Law in Protection of Traditional Knowledge Brendan Tobin Index

Small Polaron Hopping And High-Temperature Dc Conductivity Of Chalcogenide Glasses

D.C. conductivity behaviour of a variety of chalcogenide glasses have been analysed using ln σ vs Image plots as suggested in the multiphonon assisted polaron hopping model of Triberis and Friedman. The agreement with the model is very satisfactory and further analysis of the model using c.

Temperature dependence of the surface conductivity of YBa2Cu3O7−δ accompanying the change in the concentration of dimerized oxygen holes

The intensity of inelastically scattered electrons measured by electron energy loss spectroscopy has been employed to monitor the surface conductivity of YBa2Cu3O6.9 as a function of temperature. The study shows a drastic change in surface conductivity precedes the superconducting transition at 90K. The increase in surface conductivity is accompanied by the formation of dimerized holes in the oxygen derived p-band. This phenomenon is not observed in the non-superconducting YBa2Cu3O6.2.

Australian Property Institute Inc, Submission to the Productivity Commission on Intellectual Property Arrangements – Issues Paper

This submission responds to the document Intellectual Property Arrangements Issues Paper (Issues Paper) released by the Productivity Commission in October 2015 for public consultation and input by 30 November 2015. The API is grateful for the extension of time granted by the Commission to complete and lodge this submission. The overall need for an inquiry into intellectual property is supported by API. In particular it is noted with approval that the Commission states in its Issues Paper that it is to consider the appropriate balance between “incentives for innovation and investments, and the interests of both individuals and businesses in assessing products”.1 However, API is of the view that intellectual property in the area of real property presents a number of issues which are not fully canvassed in the abovementioned Issues Paper. Intellectual property embedded in valuation and other property-related reports of API members involves the acquisition of information which may possibly be confidential. Yet, when engaged in banks and financial institutions the intellectual property in such valuations and/ or reports is commonly required to be passed to the client bank or financial institution. In the Issues Paper it is proposed that there are seven different forms of intellectual property rights.2 It is the view of API that an eight form exists, namely private agreements. The Issues Paper, however, regards private agreements between firms as alternatives to intellectual property rights. The API considers that “secrecy or confidentiality arrangements”3 as identified in the Issues Paper form a much larger part of the manner in which intellectual property is maintained in Australia for the purposes of trade secrecy or more often, financial confidentiality...

Intellectual Property Chapter in Part 18: Intellectual Property and Communications

This chapter addresses the areas more commonly found in everyday practice (NB circuit layouts and plant breeder's rights are not covered). Importantly, IP law has become very specialised, and as such one for which practitioners will need expertise or access to relevant experts in order to properly provide advice. The following therefore is an overview only of relevant issues.

Sensing Shape Recovery Using Conductivity Noise in Thin Films of NiTi Shape Memory Alloys

Low frequency fluctuations in the electrical resistivity, or noise, have been used as a sensitive tool to probe into the temperature driven martensite transition in dc magnetron sputtered thin films of nickel titanium shape-memory alloys. Even in the equilibrium or static case, the noise magnitude was more than nine orders of magnitude larger than conventional metallic thin films and had a characteristic dependence on temperature. We observe that the noise while the temperature is being ramped is far larger as compared to the equilibrium noise indicating the sensitivity of electrical resistivity to the nucleation and propagation of domains during the shape recovery. Further, the higher order statistics suggests the existence of long range correlations during the transition. This new characterization is based on the kinetics of disorder in the system and separate from existing techniques and can be integrated to many device applications of shape memory alloys for in-situ shape recovery sensing.