943 resultados para computational fluid dynamics (CFD)
Resumo:
Questo lavoro si concentra sullo studio fluidodinamico del flusso multifase cavitante di un iniettore per applicazioni a motori ad iniezione diretta (GDI). L’analisi è stata svolta tramite l’uso del software CFD (Computational Fluid Dynamics) Star-CCM+^® sviluppato da CD-ADAPCO. L’obiettivo di questo studio è investigare i motivi che portano ad un diverso comportamento tra i rilievi della prova sperimentale di caratterizzazione dell’iniettore e quanto atteso dai valori nominali dettati dalla specifica dell’iniettore, con particolare riferimento alla distribuzione di portata fra i diversi ugelli. Il presente lavoro fa parte di una coppia di elaborati collegati tra loro e, pertanto, ha inoltre lo scopo di fornire dati utili allo sviluppo dell’altro tema di analisi mirato alla individuazione di parametri di qualità della miscela aria-combustibile non reagente utili alla previsione della formazione del particolato prodotto dalla combustione di un motore GDI. L’elaborato, costituito di 5 capitoli, è strutturato secondo lo schema sottostante. Nel capitolo 1 vengono presentate le motivazioni che lo hanno avviato e viene esposto lo stato dell’arte della tecnologia GDI. Il capitolo 2 è a sfondo teorico: in esso vengono riportati i fondamenti del processo di cavitazione nella prima parte e i modelli numerici utilizzati nell’analisi nella seconda. Il capitolo 3 descrive la modellazione e successiva validazione dei modelli tramite confronto con il test case ‘Comprensive hydraulic and flow field documentation in model throttle experiments under cavitation conditions’ (E. Winklhofer, 2001). Nella scelta dei modelli e dei parametri relativi, l’analisi si è basata su precedenti lavori trovati in letteratura. Successivamente è stato svolto uno studio di sensibilità per valutare la stabilità della soluzione a piccole variazioni nei valori dei parametri. La scelta dei parametri modellistici nel caso di interesse, l’iniettore multihole, si è basata inizialmente sui valori ‘ottimali’ ottenuti nel test case ed è l’argomento del capitolo 4. All’interno del capitolo si parla inoltre dell’analisi di sensibilità successiva, svolta con lo scopo di comprendere i motivi che portano allo sbilanciamento tra fori corrispondenti e al maggiore sviluppo del getto centrale rispetto agli altri. Nel capitolo 5 dopo un breve riepilogo dei punti fondamentali trattati nello svolgimento dell’elaborato, si tirano le conclusioni sull’analisi e si espongono gli sviluppi futuri.
Resumo:
OBJECTIVE: The purpose of this study was to compare a standard peripheral end-hole angiocatheter with those modified with side holes or side slits using experimental optical techniques to qualitatively compare the contrast material exit jets and using numeric techniques to provide flow visualization and quantitative comparisons. MATERIALS AND METHODS: A Schlieren imaging system was used to visualize the angiocatheter exit jet fluid dynamics at two different flow rates. Catheters were modified by drilling through-and-through side holes or by cutting slits into the catheters. A commercial computational fluid dynamics package was used to calculate numeric results for various vessel diameters and catheter orientations. RESULTS: Experimental images showed that modifying standard peripheral IV angiocatheters with side holes or side slits qualitatively changed the overall flow field and caused the exiting jet to become less well defined. Numeric calculations showed that the addition of side holes or slits resulted in a 9-30% reduction of the velocity of contrast material exiting the end hole of the angiocatheter. With the catheter tip directed obliquely to the wall, the maximum wall shear stress was always highest for the unmodified catheter and was always lowest for the four-side-slit catheter. CONCLUSION: Modified angiocatheters may have the potential to reduce extravasation events in patients by reducing vessel wall shear stress.
Resumo:
Conservative medical treatment is commonly first recommended for patients with uncomplicated Type-B aortic dissection (AD). However, if dissection-related complications occur, endovascular repair or open surgery is performed. Here we establish computational models of AD based on radiological three-dimensional images of a patient at initial presentation and after 4-years of best medical treatment (BMT). Computational fluid dynamics analyses are performed to quantitatively investigate the hemodynamic features of AD. Entry and re-entries (functioning as entries and outlets) are identified in the initial and follow-up models, and obvious variations of the inter-luminal flow exchange are revealed. Computational studies indicate that the reduction of blood pressure in BMT patients lowers pressure and wall shear stress in the thoracic aorta in general, and flattens the pressure distribution on the outer wall of the dissection, potentially reducing the progressive enlargement of the false lumen. Finally, scenario studies of endovascular aortic repair are conducted. The results indicate that, for patients with multiple tears, stent-grafts occluding all re-entries would be required to effectively reduce inter-luminal blood communication and thus induce thrombosis in the false lumen. This implicates that computational flow analyses may identify entries and relevant re-entries between true and false lumen and potentially assist in stent-graft planning.
Resumo:
Es importante disponer de una herramienta con la cual diseñar dispositivos de uso industrial y comercial que trabajen con metales líquidos (fuentes de neutrones de alta intensidad, núcleos de sistemas de transmutación nuclear, reactores de fisión de nueva generación, instalaciones de irradiación de materiales o reactores de fusión nuclear). Los códigos CFD (Computational Fluid Dynamics) son una de esas herramientas, y la manera de llevar a cabo su validación es la simulación de experimentos existentes. La turbulencia y la presencia de dos o más fases, son los dos principales problemas a los que tiene que hacer frente un código CFD. La mayoría de los modelos de turbulencia presentes en los códigos CFD se basan en considerar la proporcionalidad directa entre el transporte de cantidad de movimiento turbulento y el transporte turbulento de calor. Precisamente, el coeficiente de difusión del calor turbulento, se asume que sea proporcional a la viscosidad turbulenta a través de una constante empírica, llamada número de Prandtl turbulento. El valor de este número, en los códigos comerciales está entre 0,9 y 0,85 dependiendo del modelo de turbulencia, lo cual significa que en los códigos se asume que el transporte turbulento tanto de cantidad de movimiento como de calor, son prácticamente equivalentes. Esta asunción no es cierta en los flujos de metales líquidos, donde se demuestra que la transmisión de calor por turbulencia es pequeña frente a la transmisión de calor molecular. La solución pasa por aumentar el número de Prandtl turbulento, o abandonar la analogía de Reynolds, en el tratamiento de la turbulencia. Por otro lado, en los metales líquidos la capa límite térmica es más ancha que la de velocidad, y las funciones de pared incluidas en los códigos no satisfacen adecuadamente los flujos turbulentos de los fluidos con bajo número de Prantdl (los metales líquidos). Sí serían adecuados, si el mallado es tal, que la celda más cercana a la pared, está dentro de la subcapa laminar, en la cual la propiedad dominante es la conductividad molecular. En la simulación de flujo multifase los códigos se encuentran con una serie de dificultades, que en el caso de que las densidades de los fluidos que intervienen sean muy diferentes entre sí (como ocurre con los metales líquidos y los gases), serán aún mayores. La modelización de la interfase gas metal líquido, así como el encontrar una correlación válida para los coeficientes de resistencia y sustentación para el movimiento de las burbujas en el seno del metal líquido, son dos de los principales retos en la simulación de este tipo de flujos. Las dificultades no se limitan sólo a la simulación mediante CFD, las medidas experimentales de velocidad de las burbujas y del metal líquido también son complicadas. Hay parámetros que no se pueden definir bien: la trayectoria y la forma de las burbujas entre ellos. En el campo de aplicación industrial de los metales líquidos, los altos valores de los coeficientes de expansión volumétrica y de conductividad térmica hacen que estos fluidos sean muy atractivos en la refrigeración por convección libre en dispositivos de alta densidad de potencia. Tomando como base uno de los diseños de ADS (Accelerator Driven System), y teniendo en cuenta la dificultad que conlleva el uso de múltiples modelos físicos, los cálculos realizados muestran cómo, en caso de fallo eléctrico, la operación de la instalación puede continuar de forma segura. Para la validación de los códigos CFD en su uso como herramienta de diseño, uno de los fenómenos donde cuantitativamente más dificultades encuentran los códigos es en los que aparecen en la modelización de las superficies libres. Un buen ajuste de los modelos multifase y de turbulencia es imprescindible en este tipo de simulaciones. Efectivamente, en la instalación de irradiación de materiales IFMIF, la formación de ondas en la superficie libre del flujo de Litio, es un fenómeno que hay que tratar de evitar, y además se requiere predecir las temperaturas, para ver si hay peligro de ebullición del metal líquido. La simulación llevada a cabo se enfoca al análisis termohidráulico. Variando la velocidad de inyección de Litio desde 10 hasta 20 m/s, se comprueba que las temperaturas máximas quedan alejadas del punto de ebullición del Litio, debido al aumento de presión producido por la fuerza centrífuga. Una de las cuestiones más críticas que se presentan en las fuentes de neutrones sería la refrigeración de la ventana metálica sobre la que incide el haz de protones. La simulación de experimentos como MEGAPIE y TS-1, permite la “visualización” de recirculación en el flujo, de los puntos de estancamiento, de los puntos calientes, etc, y da una fotografía de las zonas críticas del diseño.
Resumo:
Some basic ideas are presented for the construction of robust, computationally efficient reduced order models amenable to be used in industrial environments, combined with somewhat rough computational fluid dynamics solvers. These ideas result from a critical review of the basic principles of proper orthogonal decomposition-based reduced order modeling of both steady and unsteady fluid flows. In particular, the extent to which some artifacts of the computational fluid dynamics solvers can be ignored is addressed, which opens up the possibility of obtaining quite flexible reduced order models. The methods are illustrated with the steady aerodynamic flow around a horizontal tail plane of a commercial aircraft in transonic conditions, and the unsteady lid-driven cavity problem. In both cases, the approximations are fairly good, thus reducing the computational cost by a significant factor.
Resumo:
Assessing wind conditions on complex terrain has become a hard task as terrain complexity increases. That is why there is a need to extrapolate in a reliable manner some wind parameters that determine wind farms viability such as annual average wind speed at all hub heights as well as turbulence intensities. The development of these tasks began in the early 90´s with the widely used linear model WAsP and WAsP Engineering especially designed for simple terrain with remarkable results on them but not so good on complex orographies. Simultaneously non-linearized Navier Stokes solvers have been rapidly developed in the last decade through CFD (Computational Fluid Dynamics) codes allowing simulating atmospheric boundary layer flows over steep complex terrain more accurately reducing uncertainties. This paper describes the features of these models by validating them through meteorological masts installed in a highly complex terrain. The study compares the results of the mentioned models in terms of wind speed and turbulence intensity.
Resumo:
Use of computational fluid dynamic (CFD) methods to predict the power production from wind entire wind farms in flat and complex terrain is presented in this paper. Two full 3D Navier–Stokes solvers for incompressible flow are employed that incorporate the k–ε and k–ω turbulence models respectively. The wind turbines (W/Ts) are modelled as momentum absorbers by means of their thrust coefficient using the actuator disk approach. The WT thrust is estimated using the wind speed one diameter upstream of the rotor at hub height. An alternative method that employs an induction-factor based concept is also tested. This method features the advantage of not utilizing the wind speed at a specific distance from the rotor disk, which is a doubtful approximation when a W/T is located in the wake of another and/or the terrain is complex. To account for the underestimation of the near wake deficit, a correction is introduced to the turbulence model. The turbulence time scale is bounded using the general “realizability” constraint for the turbulent velocities. Application is made on two wind farms, a five-machine one located in flat terrain and another 43-machine one located in complex terrain. In the flat terrain case, the combination of the induction factor method along with the turbulence correction provides satisfactory results. In the complex terrain case, there are some significant discrepancies with the measurements, which are discussed. In this case, the induction factor method does not provide satisfactory results.
Resumo:
The fluid-dynamics of the corona ejected by laser-fusion targets in the direct-drive approach (thermal radiation and atomic physics unimportant) is discussed. A two-fluid model involves inverse bremsstrahlung absorption, refraction, different ion and electron temperatures with energy exchange, different ion and electron velocities and magnetic field generation, and their effect on ion-electron friction and heat flux. Four dimensionless parameters determine coronal regimes for one-dimensional flows under uniform irradiation. One additional parameter is involved in two-dimensional problems,including the stability of one-dimensional flows, and the smoothing of nonuniform driving.
Resumo:
La mejora del comportamiento aerodinámico de vehículos pesados en la carretera ha adquirido una mayor importancia estos últimos años debido a la crisis y su consecuente aumento del precio de los combustibles. Dado que una reducción en la resistencia aerodinámica del vehículo conlleva un menor empleo de combustible, el objetivo de este proyecto es realizar un estudio paramétrico del conjunto tractor-tráiler mediante la mecánica de fluidos computacional (CFD) para así obtener la geometría que proporciona un menor gasto de combustible cuando ésta es expuesta a viento frontal. La influencia de 3 parámetros, que son la separación existente entre cabina y remolque, la altura del remolque y el radio de curvatura de las aristas frontales de la cabina, es analizada en este estudio dividido en varias etapas que implican el uso de programas específicos como son: la parametrización y creación de las geometrías en 3D que es llevada a cabo mediante CATIA, el mallado del dominio (realizado con Gambit) y resolución de las ecuaciones mediante FLUENT. Finalmente se obtendrá una relación entre la resistencia aerodinámica (representada mediante el coeficiente de arrastre) y la combinación de los 3 parámetros, que nos permitirá decidir que geometría es la óptima. Abstract The improvement of the heavy vehicle’s aerodynamic behavior on the road has gained a great importance for these last years because of the economic crisis and the consequent increase of the price of the fuels. Due to the fact that a reduction in the aerodynamic resistance of the vehicle involves using a smaller amount of fuel, the objective of this project is to carry out a parametric study about the ensemble tractor-trailer by computational fluid dynamics methods (CFD) in order to obtain the geometry which expense of fuel is the lowest when it’s exposed to frontal wind. The influence of the three parameters, which are the space between cab and trailer, the height of the trailer and the curvature of the frontal cab edges, is analysed in this study which is divided into different parts involving specific programs: choosing the parameters and building the geometries, which is done by using CATIA, the mesh is built by Gambit, and the program equations-solver is FLUENT. Finally a ratio between aerodynamic resistance and a combination of the three parameters will be obtained and it will allow us to choose the best geometry.
Resumo:
We propose in this work a very simple torsion-free beam element capable of capturing geometrical nonlinearities. The simple formulation is objective and unconditionally con- vergent for geometrically nonlinear models with large displacements, in the traditional sense that guarantees more precise numerical solutions for finer discretizations. The formulation does not employ rotational degrees of freedom, can be applied to two and three-dimensional problems, and it is computationally very efficient.
Resumo:
The present study shows a first approach to the simulation of the remote handling oper- ation which takes into account the thermal and flexible behavior of the blanket segments and its implications on the remote handling equipment, in order to validate and improve its design.
Understanding and improving the chemical vapor deposition process for solar grade silicon production
Resumo:
Esta Tesis Doctoral se centra en la investigación del proceso de producción de polisilicio para aplicaciones fotovoltaicas (FV) por la vía química; mediante procesos de depósito en fase vapor (CVD). El polisilicio para la industria FV recibe el nombre de silicio de grado solar (SoG Si). Por un lado, el proceso que domina hoy en día la producción de SoG Si está basado en la síntesis, destilación y descomposición de triclorosilano (TCS) en un reactor CVD -denominado reactor Siemens-. El material obtenido mediante este proceso es de muy alta pureza, pero a costa de un elevado consumo energético. Así, para alcanzar los dos principales objetivos de la industria FV basada en silicio, bajos costes de producción y bajo tiempo de retorno de la energía invertida en su fabricación, es esencial disminuir el consumo energético de los reactores Siemens. Por otro lado, una alternativa al proceso Siemens considera la descomposición de monosilano (MS) en un reactor de lecho fluidizado (FBR). Este proceso alternativo tiene un consumo energético mucho menor que el de un reactor Siemens, si bien la calidad del material resultante es también menor; pero ésta puede ser suficiente para la industria FV. A día de hoy los FBR deben aún abordar una serie de retos para que su menor consumo energético sea una ventaja suficiente comparada con otras desventajas de estos reactores. En resumen, la investigación desarrollada se centra en el proceso de depósito de polysilicio por CVD a partir de TCS -reactor Siemens-; pero también se investiga el proceso de producción de SoG Si en los FBR exponiendo las fortalezas y debilidades de esta alternativa. Para poder profundizar en el conocimiento del proceso CVD para la producción de polisilicio es clave el conocimiento de las reacciones químicas fundamentales y cómo éstas influencian la calidad del producto resultante, al mismo tiempo que comprender los fenómenos responsables del consumo energético. Por medio de un reactor Siemens de laboratorio en el que se llevan a cabo un elevado número de experimentos de depósito de polisilicio de forma satisfactoria se adquiere el conocimiento previamente descrito. Se pone de manifiesto la complejidad de los reactores CVD y de los problemas asociados a la pérdidas de calor de estos procesos. Se identifican las contribuciones a las pérdidas de calor de los reactores CVD, éstas pérdidas de calor son debidas principalmente a los fenómenos de radiación y, conducción y convección vía gases. En el caso de los reactores Siemens el fenómeno que contribuye en mayor medida al alto consumo energético son las pérdidas de calor por radiación, mientras que en los FBRs tanto la radiación como el calor transferido por transporte másico contribuyen de forma importante. Se desarrolla un modelo teórico integral para el cálculo de las pérdidas de calor en reactores Siemens. Este modelo está formado a su vez por un modelo para la evaluación de las pérdidas de calor por radiación y modelos para la evaluación de las pérdidas de calor por conducción y convección vía gases. Se ponen de manifiesto una serie de limitaciones del modelo de pérdidas de calor por radiación, y se desarrollan una serie de modificaciones que mejoran el modelo previo. El modelo integral se valida por medio un reactor Siemens de laboratorio, y una vez validado se presenta su extrapolación a la escala industrial. El proceso de conversión de TCS y MS a polisilicio se investiga mediante modelos de fluidodinámica computacional (CFD). Se desarrollan modelados CFD para un reactor Siemens de laboratorio y para un prototipo FBR. Los resultados obtenidos mediante simulación son comparados, en ambos casos, con resultados experimentales. Los modelos desarrollados se convierten en herramientas para la identificación de aquellos parámetros que tienen mayor influencia en los procesos CVD. En el caso del reactor Siemens, ambos modelos -el modelo integral y el modelado CFD permiten el estudio de los parámetros que afectan en mayor medida al elevado consumo energético, y mediante su análisis se sugieren modificaciones para este tipo de reactores que se traducirían en un menor número de kilovatios-hora consumidos por kilogramo de silicio producido. Para el caso del FBR, el modelado CFD permite analizar el efecto de una serie de parámetros sobre la distribución de temperaturas en el lecho fluidizado; y dicha distribución de temperaturas está directamente relacionada con los principales retos de este tipo de reactores. Por último, existen nuevos conceptos de depósito de polisilicio; éstos se aprovechan de la ventaja teórica de un mayor volumen depositado por unidad de tiempo -cuando una mayor superficie de depósito está disponible- con el objetivo de reducir la energía consumida por los reactores Siemens. Estos conceptos se exploran mediante cálculos teóricos y pruebas en el reactor Siemens de laboratorio. ABSTRACT This Doctoral Thesis comprises research on polysilicon production for photovoltaic (PV) applications through the chemical route: chemical vapor deposition (CVD) process. PV polysilicon is named solar grade silicon (SoG Si). On the one hand, the besetting CVD process for SoG Si production is based on the synthesis, distillation, and decomposition of thriclorosilane (TCS) in the so called Siemens reactor; high purity silicon is obtained at the expense of high energy consumption. Thus, lowering the energy consumption of the Siemens process is essential to achieve the two wider objectives for silicon-based PV technology: low production cost and low energy payback time. On the other hand, a valuable variation of this process considers the use of monosilane (MS) in a fluidized bed reactor (FBR); lower output material quality is obtained but it may fulfil the requirements for the PV industry. FBRs demand lower energy consumption than Siemens reactors but further research is necessary to address the actual challenges of these reactors. In short, this work is centered in polysilicon CVD process from TCS -Siemens reactor-; but it also offers insights on the strengths and weaknesses of the FBR for SoG Si production. In order to aid further development in polysilicon CVD is key the understanding of the fundamental reactions and how they influence the product quality, at the same time as to comprehend the phenomena responsible for the energy consumption. Experiments conducted in a laboratory Siemens reactor prove the satisfactory operation of the prototype reactor, and allow to acquire the knowledge that has been described. Complexity of the CVD reactors is stated and the heat loss problem associated with polysilicon CVD is addressed. All contributions to the energy consumption of Siemens reactors and FBRs are put forward; these phenomena are radiation and, conduction and convection via gases heat loss. In a Siemens reactor the major contributor to the energy consumption is radiation heat loss; in case of FBRs radiation and heat transfer due to mass transport are both important contributors. Theoretical models for radiation, conduction and convection heat loss in a Siemens reactor are developed; shaping a comprehensive theoretical model for heat loss in Siemens reactors. Limitations of the radiation heat loss model are put forward, and a novel contribution to the existing model is developed. The comprehensive model for heat loss is validated through a laboratory Siemens reactor, and results are scaled to industrial reactors. The process of conversion of TCS and MS gases to solid polysilicon is investigated by means of computational fluid-dynamics models. CFD models for a laboratory Siemens reactor and a FBR prototype are developed. Simulated results for both CVD prototypes are compared with experimental data. The developed models are used as a tool to investigate the parameters that more strongly influence both processes. For the Siemens reactors, both, the comprehensive theoretical model and the CFD model allow to identify the parameters responsible for the great power consumption, and thus, suggest some modifications that could decrease the ratio kilowatts-hour per kilogram of silicon produced. For the FBR, the CFD model allows to explore the effect of a number of parameters on the thermal distribution of the fluidized bed; that is the main actual challenge of these type of reactors. Finally, there exist new deposition surface concepts that take advantage of higher volume deposited per time unit -when higher deposition area is available- trying to reduce the high energy consumption of the Siemens reactors. These novel concepts are explored by means of theoretical calculations and tests in the laboratory Siemens prototype.
Resumo:
This paper deals with the prediction of velocity fields on the 2415-3S airfoil which will be used for an unmanned aerial vehicle with internal propulsion system and in this way analyze the air flow through an internal duct of the airfoil using computational fluid dynamics. The main objective is to evaluate the effect of the internal air flow past the airfoil and how this affects the aerodynamic performance by means of lift and drag forces. For this purpose, three different designs of the internal duct were studied; starting from the base 2415-3S airfoil developed in previous investigation, basing on the hypothesis of decreasing the flow separation produced when the propulsive airflow merges the external flow, and in this way obtaining the best configuration. For that purpose, an exhaustive study of the mesh sensitivity was performed. It was used a non-structured mesh since the computational domain is three-dimensional and complex. The selected mesh contains approximately 12.5 million elements. Both the computational domain and the numerical solution were made with commercial CAD and CFD software, respectively. Air, incompressible and steady was analyzed. The boundary conditions are in concordance with experimental setup in the AF 6109 wind tunnel. The k-e model is utilized to describe the turbulent flow process as followed in references. Results allowed obtaining velocity contours as well as lift and drag coefficients and also the location of separation and reattachment regions in some cases for zero degrees of angle of attack on the internal and external surfaces of the airfoil. Finally, the selection of the configuration with the best aerodynamic performance was made, selecting the option without curved baffles.
Resumo:
This paper deals with the prediction of pressure and velocity fields on the 2415-3S airfoil which will be used for and unmanned aerial vehicle with internal propulsion system and in this way analyze the air flow through an internal duct of the airfoil using computational fluid dynamics. The main objective is to evaluate the effect of the internal air flow past the airfoil and how this affects the aerodynamic performance by means of lift and drag forces. For this purpose, three different designs of the internal duct were studied; starting from the base 2415-3S airfoil developed in previous investigation, basing on the hypothesis of decreasing the flow separation produced when the propulsive airflow merges the external flow, and in this way obtaining the best configuration. For that purpose, an exhaustive study of the mesh sensitivity was performed. It was used a non-structured mesh since the computational domain is tridimensional and complex. The selected mesh contains approximately 12.5 million elements. Both the computational domain and the numerical solution were made with commercial CAD and CFD software respectively. Air, incompressible and steady was analyzed. The boundary conditions are in concordance with experimental setup in the AF 6109 wind tunnel. The k-ε model is utilized to describe the turbulent flow process as followed in references. Results allowed obtaining pressure and velocity contours as well as lift and drag coefficients and also the location of separation and reattachment regions in some cases for zero degrees of angle of attack on the internal and external surfaces of the airfoil. Finally, the selection of the configuration with the best aerodynamic performance was made, selecting the option without curved baffles.