Influence of growth temperature and carrier flux on the structure and transport properties of highly oriented CrO2 on Al2O3 (0001)

In this work we report on the structure and magnetic and electrical transport properties of CrO2 films deposited onto (0001) sapphire by atmospheric pressure (AP)CVD from a CrO3 precursor. Films are grown within a broad range of deposition temperatures, from 320 to 410 degrees C, and oxygen carrier gas flow rates of 50-500 seem, showing that it is viable to grow highly oriented a-axis CrO2 films at temperatures as low as 330 degrees C i.e., 60-70 degrees C lower than is reported in published data for the same chemical system. Depending on the experimental conditions, growth kinetic regimes dominated either by surface reaction or by mass-transport mechanisms are identified. The growth of a Cr2O3 interfacial layer as an intrinsic feature of the deposition process is studied and discussed. Films synthesized at 330 degrees C keep the same high quality magnetic and transport properties as those deposited at higher temperatures.

Laser-assisted deposition of thin films from photoexcited vapour phases

Laser-assisted chemical vapour deposition (LCVD) has been extensively studied in the last two decades. A vast range of applications encompass various areas such as microelectronics, micromechanics, microelectromechanics and integrated optics, and a variety of metals, semiconductors and insulators have been grown by LCVD. In this article, we review briefly the LCVD process and present two case studies of thin film deposition related to laser thermal excitation (e.g., boron carbide) and non-thermal excitation (e.g., CrO(2)) of the gas phase.

Morphological and structural characterization of CrO2/Cr2O3 films grown by laser-CVD

This work reports on the synthesis of chromium (III, IV) oxides films by KrF laser-assisted CVD. Films were deposited onto sapphire substrates at room temperature by the photodissociation of Cr(CO)(6) in dynamic atmospheres containing oxygen and argon. A study of the processing parameters has shown that partial pressure ratio Of O-2 to Cr(CO)(6) and laser fluence are the prominent parameters that have to be accurately controlled in order to co-deposit both the crystalline oxide phases. Films consistent with such a two-phase system were synthesised for a laser fluence of 75 mJ cm(-2) and a partial pressure ratio of about 1. (c) 2005 Elsevier B.V. All rights reserved.

Structural and Microanalytical Studies of CrO2 Thin Films on c-Sapphire by High Resolution Electron Microscopy Methods

Chromium dioxide (CrO2) has been extensively used in the magnetic recording industry. However, it is its ferromagnetic half-metallic nature that has more recently attracted much attention, primarily for the development of spintronic devices. CrO2 is the only stoichiometric binary oxide theoretically predicted to be fully spin polarized at the Fermi level. It presents a Curie temperature of ∼ 396 K, i.e. well above room temperature, and a magnetic moment of 2 mB per formula unit. However an antiferromagnetic native insulating layer of Cr2O3 is always present on the CrO2 surface which enhances the CrO2 magnetoresistance and might be used as a barrier in magnetic tunnel junctions.

Avaliação da qualidade química e microbiológica de tintas didácticas do ensino pré-escolar

As tintas utilizadas nas actividades didácticas possuem na sua composição ingredientes que dada a sua natureza, modo de fabrico e de utilização, podem representar um risco para a saúde das crianças. Neste âmbito, procurou-se com este estudo avaliar a qualidade química e microbiológica das tintas utilizadas pelas crianças no ensino pré-escolar. Vinte e nove amostras de tintas, incluindo guaches, tintas de águas, digitintas e tintas para pinturas faciais foram recolhidas em oito estabelecimentos de ensino, nomeadamente, Jardins de Infância, do conselho de Vila Nova de Gaia. A avaliação microbiológica envolveu não só a determinação da concentração microbiana presente nas amostras, como também, a avaliação da estabilidade microbiana nas tintas das espécies S.aureus e E.coli. Na avaliação química procedeu-se à determinação da concentração dos metais chumbo (Pb), cádmio (Cd), crómio (Cr), cobalto (Co), níquel (Nq), manganês (Mn), cobre (Cu) e zinco (Zn) quer em algumas das amostras recolhidas nos estabelecimentos de ensino, quer em tintas adquiridas em três estabelecimentos comerciais. Os resultados obtidos da avaliação microbiológica revelam uma contaminação estática na generalidade das tintas. Três amostras de tintas apresentaram ainda elevada contaminação por fungos, nomeadamente Aspergillus spp. e Trichophyton spp. Da avaliação da estabilidade microbiana das espécies S.aureus e E.coli observou-se uma sensibilidade das mesmas às tintas, sendo evidenciado, em alguns casos, um decrescimento da concentração ao longo do tempo de exposição, e noutros, uma sensibilidade imediata. A espécie S.aureus revelou, contudo, maior capacidade de resistência que a E.coli. Os resultados obtidos da avaliação química revelaram a presença de Cr em todas as amostras, registando as tintas adquiridas em estabelecimentos comerciais concentrações mais elevadas para este metal. Os metais Cu e Zn foram detectados, em algumas amostras de tintas artísticas, em concentrações acima dos valores limites. Nas tintas para a cara foram encontrados os metais Pb, Cd, Cr e Nq, cuja utilização é interdita nestes produtos. O conhecimento das características químicas e microbiológicas das tintas utilizadas por crianças do ensino pré-escolar revelou-se de grande importância, nomeadamente, para a determinação dos riscos a que este grupo de indivíduos pode estar exposto no seu dia-a-dia quando utilizam estes produtos.

Activos fixos tangíveis numa empresa industrial do ramo automóvel transição para o SNC

Dissertação para a obtenção do grau de mestre em Contabilidade e Finanças Orientador: Mestre António Costa Reis

Determinação preliminar de parâmetros construtivos de barreiras reactivas permeáveis com recurso a colunas para remediação de crómio com ferro zerovalente

Um dos principais problemas com que se deparam as sociedades actuais, e que é consequência da sua forma de se organizar prende-se com a mudança das características originais dos locais onde habitam e dos seus componentes como resultado das actividades humanas que transformam solos e águas em depósitos de resíduos. Entre as substâncias que são depositadas no meio físico, que requerem especial atenção, encontra-se o grupo dos metais pesados, uma vez que são considerados como perigosos pela sua toxicidade e potencial cancerígeno quando em contacto com populações ou ecossistemas. Destes metais, o crómio é um dos metais que requer especial atenção devido a sua relativa abundância como contaminante, e à periculosidade dos seus iões, em especial o Cr6+. Este trabalho pretende contribuir para o conhecimento dos fenómenos geoambientais associados à remediação de águas contaminadas com Cr6+ recorrendo ao ferro monovalente de forma a estabelecer parâmetros de aplicabilidade através de estudos laboratoriais baseados em ensaios em colunas.

Estudo da estabilidade térmica da pele

Mestrado em Engenharia Química

The effect of the angle of incidence on the aqueous corrosion of ion implanted M50 steel substrates

Following work on tantalum and chromium implanted flat M50 steel substrates, this work reports on the electrochemical behaviour of M50 steel implanted with tantalum and chromium and the effect of the angle of incidence. Proposed optimum doses for resistance to chloride attack were based on the interpretation of results obtained during long-term and accelerated electrochemical testing. After dose optimization from the corrosion viewpoint, substrates were implanted at different angles of incidence (15°, 30°, 45°, 60°, 75°, 90°) and their susceptibility to localized corrosion assessed using open-circuit measurements, step by step polarization and cyclic voltammetry at several scan rates (5–50 mV s-1). Results showed, for tantalum implanted samples, an ennoblement of the pitting potential of approximately 0.5 V for an angle of incidence of 90°. A retained dose of 5 × 1016 atoms cm-2 was found by depth profiling with Rutherford backscattering spectrometry. The retained dose decreases rapidly with angle of incidence. The breakdown potential varies roughly linearly with the angle of incidence up to 30° falling fast to reach -0.1 V (vs. a saturated calomel electrode (SCE)) for 15°. Chromium was found to behave differently. Maximum corrosion resistance was found for angles of 45°–60° according to current densities and breakdown potentials. Cr+ depth profiles ((p,γ) resonance broadening method), showed that retained doses up to an angle of 60° did not change much from the implanted dose at 90°, 2 × 1017 Cr atoms cm-2. The retained implantation dose for tantalum and chromium was found to follow a (cos θ)8/3 dependence where θ is the angle between the sample normal and the beam direction.

Estudo da obtenção de gelatina a partir de raspa Wet-Blue da indústria de curtumes

Mestrado em Engenharia Química. Ramo Tecnologias de Protecção Ambiental.

Análise de metais em infusões de chás e ervas aromáticas por espectrofotometria de absorção atómica de alta resolução com fonte contínua

Actualmente tem-se verificado um grande aumento na procura e a utilização de produtos naturais contendo extractos de algas, com fins medicinais, sendo cada vez maior a diversidade de oferta desses produtos, vendidos em ervanária e afins. A bibliografia tem mostrado que as algas têm capacidade de acumulação de metais pesados. As algas, sendo organismos aquáticos, estão sujeitas a contaminações dos locais (não identificados) de onde provêm. O controlo e fiscalização para estes produtos é praticamente inexistente. O objectivo deste projecto foi o desenvolvimento de metodologias analíticas com vista à quantificação de metais em infusões de chás e ervas aromáticas. Foram analisadas 9 amostras: uma de chá verde, uma de chá preto, uma infusão de lima, uma de camomila, uma mistura de chá com ervas e quatro misturas contendo algas. A espectrofotometria de absorção atómica é o método de referência para a análise de metais. Neste trabalho foi utilizado um espectrofotómetro de absorção atómica com fonte de radiação contínua e monocromador de alta resolução. Sendo esta uma tecnologia inovadora foi necessário desenvolver metodologias para os métodos de análise. A atomização em chama foi a técnica utilizada para a quantificação do cálcio, potássio, magnésio, manganês e sódio. A atomização electrotérmica foi usada para o cádmio, cobalto, crómio, cobre, níquel e chumbo. Tendo em conta os limites legislados (Decreto-Lei Nº306/2007 de 27 de Agosto) obtiveram-se teores preocupantes para o níquel (iguais ou superiores ao limite legislado) em todas as amostras analisadas e para o manganês em duas das amostras (chá verde e chá preto). Todas as amostras contendo algas apresentaram teores de Ca, Mg e Na superiores aos das restantes. Para os restantes elementos não foi possível relacionar as concentrações com a composição das infusões, em particular a presença de algas.

Nephrotoxicity of CCA-treated wood: a comparative study with As2O5 and CrO3 on mice

The purpose of this work was to assess the acute toxicity on male mice to a chromated copper arsenate (CCA) solution, a widespread wood preservative used in building industry until 2002. Animals were subcutaneously injected with CCA (7.2 mg/kg arsenic and 10.2 mg/kg chromium per body weight), CrO3 (10.2 mg/kg), As2O5 (7.2 mg/kg) and NaCl (0.9%) per se, during 48 h and 96 h, for histopathology, histochemistry, chromium and arsenic analysis. The results showed some histopathological changes within renal tubules lumen of CCA exposed animals (during 48 h, and 96 h), and CrO3 (for the period of 96 h). Furthermore, the renal levels of arsenic and chromium in treated animals were statistically more evident than controls. Although, the same contents of pentavalent arsenic and hexavalent chromium were injected into treated animals with CCA and with the prepared solutions of As2O5 and CrO3, a different distribution of the pattern of these compounds was observed in kidneys.

Ecotoxicity tests using the green algae chlorella vulgaris — a useful tool in hazardous effluents management

The treatment efficiency of laboratory wastewaters was evaluated and ecotoxicity tests with Chlorella vulgaris were performed on them to assess the safety of their environmental discharge. For chemical oxygen demand wastewaters, chromium (VI), mercury (II) and silver were efficiently removedby chemical treatments.Areduction of ecotoxicitywas achieved; nevertheless, an EC50 (effective concentration that causes a 50% inhibition in the algae growth) of 1.5% (v/v) indicated still high level of ecotoxicity. For chloride determination wastewaters, an efficient reduction of chromium and silver was achieved after treatment. Regarding the reduction of ecotoxicity observed, EC50 increased from 0.059% to 0.5%, only a 0.02% concentration in the aquatic environment would guarantee no effects. Wastewaters containing phenanthroline/iron (II) complex were treated by chemical oxidation. Treatmentwas satisfactory concerning chemical parameters, although an increase in ecotoxicitywas observed (EC50 reduced from 0.31% to 0.21%). The wastes from the kinetic study of persulphate and iodide reaction were treated with sodium bisulphite until colour was removed. Although they did not reveal significant ecotoxicity, only over 1% of the untreated waste produced observable effects over algae. Therefore, ecotoxicity tests could be considered a useful tool not only in laboratory effluents treatment, as shown, but also in hazardous wastewaters management.

Trimethoprim-selective electrodes with molecularly imprinted polymers acting as ionophores and potentiometric transduction on graphite solid-contact

This work proposes a new biomimetic sensor material for trimethoprim. It is prepared by means of radical polymerization, having trimethylolpropane trimethacrylate as cross-linker, benzoyl peroxide as radicalar iniciator, chloroform as porogenic solvent, and methacrylic acid and 2-vinyl pyridine as monomers. Different percentages of sensor in a range between 1 and 6% were studied. Their behavior was compared to that obtained with ion-exchanger quaternary ammonium salt (additive tetrakis(p-chlorophenyl)borate or tetraphenylborate). The effect of an anionic additive in the sensing membrane was also tested. Trimethoprim sensors with 1% of imprinted particles from methacrylic acid monomers showed the best response in terms of slope (59.7 mV/decade) and detection limit (4.01×10−7 mol/L). These electrodes displayed also a good selectivity towards nickel, manganese aluminium, ammonium, lead, potassium, sodium, iron, chromium, sulfadiazine, alanine, cysteine, tryptophan, valine and glycine. The sensors were not affected by pH changes from 2 to 6. They were successfully applied to the analysis of water from aquaculture.

Diethydithiocarbamate complexes with metals used as food suplements show diferente effects in cancer cells

Diethyldithiocarbamate (ditiocarb), a metabolite of the old anti-alcoholic drug disulfiram (Antabuse), forms proteasome-inhibiting metal complexes with copper or zinc that suppress cancer cells both in vitro and in vivo. The drug has been used in a clinical trial (NCT00742911) along with copper gluconate as a dietary supplement in patients with cancer spreading to the liver. In this study, we demonstrate the effect of synthetic complexes of disulfiram with four various metals (Mn, Fe, Cr and Cu) used as food supplements. These complexes may be spontaneously formed in the blood during the use of disulfiram with divalent metals and thus may suppress the growth of cancer in vivo. The cytotoxic effect of the compounds and the compounds' ability to inhibit the cellular proteasome were tested in the osteosarcoma cell line U2OS. After 48 h, copper and manganese complexes exhibited cytotoxic effect on the cell line, in sharp contrast to both iron and chromium complexes. (C) 2014 Faculty of Health and Social Studies, University of South Bohemia in Ceske Budejovice. Published by Elsevier Urban & Partner Sp. z o.o. All rights reserved.