Sellumassan varastosäiliön rakenneanalyysi

Tämä työ käsittelee valkaistun ja valkaisemattoman sellumassan varastosäiliön tärinää ja värähtelyä. Värähtelyn seurauksena säiliön seinämän jäykisterenkaan hitsausliitokseen on syntynyt särö. Työn tavoitteena on selvittää, mikä johtaa särön syntyyn ja miten kestäväm-piä varastosäiliöitä voidaan rakentaa materiaali-, valmistus- tai rakennemuutoksien avulla. Työ alkoi tutkimalla rakennemateriaalina olevan duplex-teräksen mikrorakenteen ominai-suuksia, sekä sen hitsattavuutta ja seostamista kirjallisuustutkimuksena. Kirjallisuustutki-musta jatkettiin selvittämällä mahdollisia vaurion syntymekanismeja seinämän särölle. Työssä analysoitiin myös tehtaalla mitattuja värähtelyarvoja. Lopuksi laskettiin FE-analyysillä tyhjän varastosäiliön ominaismuodot ja -taajuudet moodianalyysillä, sekä selvi-tettiin harmonisella analyysillä pinnankorkeuden vaihtelun vaikutus siirtymävasteeseen ja kriittisiin värähtelytaajuuksiin. Varastosäiliöön kohdistuvaa värähtelyä ei ole mahdollista poistaa kokonaan, mutta väräh-telyn aiheuttamia seurauksia kyetään rajaamaan useilla keinoilla. Toimenpiteinä voivat olla ainakin seinämän materiaalin paksuuden lisääminen, jäykisteripojen lisääminen ja kriittisten sellun pinnankorkeuksien välttäminen. Kriittiseksi pinnankorkeudeksi havaittiin 40–45 %:n täyttöaste ja turvalliseksi korkeudeksi 35–38 %:n täyttöaste. Varastosäiliölle kriittisen ominaistaajuuden katsotaan syntyvän taajuuksilla 3,3–3,8 Hz ja 5,8–6,4 Hz. Sellumassa putoaa varastosäiliöön noin 2 Hz taajuudella.

Asiakasohjautuvan hitsaustuotannon kehittäminen PK-konepajassa

Tässä diplomityössä tarkasteltiin asiakasohjautuvan hitsaustuotannon kehittämistä PK-konepajassa. Työn tarkoituksena oli kerätä taustatietoa asiakasohjautuvan hitsaustuotannon erityispiirteistä ja tarkastella hitsaustuotannon kehittämistä. Työssä tutustuttiin hitsausprosesseihin ja niiden kehitysversioihin sekä hitsausaineisiin. Tärkeänä osa-alueena olivat hitsin ja hitsaustuotannon laadun ja laadunhallinnan sekä hitsauksen mekanisoinnin ja automatisoinnin tarkastelu hitsauksen työsuojelua ja hitsausergonomiaa unohtamatta. Tämän jälkeen kartoitettiin yrityksen nykytilanne ja laadittiin kehittämistoimenpiteet sekä tarvittavat laskelmat ja kehitystyön implementointi. Sen jälkeen vertailtiin tehostettua toimintaa vanhaan toimintaan sekä tehtiin johtopäätökset toiminnan kehittämisestä.

Convenience of scallops in plate structures

In this thesis was performed comprehensive study about the convenience of scallops in plate structures. A literature review was performed and lack of knowledge was fulfilled with fatigue tests performed in the laboratory of Steel Structures at the Lappeenranta University of Technology and with finite element method. The aim of this thesis was to produce design guidance for the use of scallops for different structural details and different loading conditions. An additional aim was to include more precise instructions for scallop design to produce good fatigue resistance and appropriate manufacturing quality. The literature review was performed searching bridge engineering and maritime standards and design guides and studies from scientific databases and reference lists from the literature of this field. Fatigue tests were used to research the effect of using scallops or not using scallops to fatigue strength of bracket specimen. Tests were performed on three specimens with different scallop radii and to five specimens without scallops with different weld penetration depths. Finite element method using solid elements, symmetry and submodels was used to determine stress concentration factors for I-beams with scallops. Stresses were defined with hot spot stress method. Choosing to use a scallop or not in the structure is affected by many factors, such as structural and loading conditions and manufacturability. As a rule of thumb, scallops should be avoided because those cause stress concentration points to the structure and take a lot of time to manufacture. When scallops are not used, good quality welding should be provided and full weld penetration is recommended to be used in load carrying corner weld areas. In some cases, it is advisable to use scallops. In that case, circular scallops are recommended to be used and radius should be chosen from fatigue strength or manufacturing point of view.

Ultralujan teräksen kaarijuotto

Tässä diplomityössä tutkitaan ultralujan rakenneteräksen kaarijuotolla valmistettujen liitosten väsymiskestävyyttä. Tutkittavat liitokset ovat kuormaa kantamattomia X-liitoksia. Tutkinnassa vertaillaan puhtaasti juottamalla valmistettua liitosta hitsauksen ja juoton kombinaatioliitokseen, jossa pohjapalkona toimivan hitsin rajaviivalle on juotettu lisäpalko. Kaarijuottoa esitellään yleisesti liittämismenetelmänä. Ultralujaa rakenneterästä esitellään yleisesti ja tarkastellaan sen metallurgista käyttäytymistä sekä juotettaessa, että hitsattaessa. Tutkimuksessa tehtiin kaikkiaan 21 väsytystestiä. Väsytystestit muodostuivat kolmesta eri koekappalesarjasta. Ensimmäisen ja toisen sarjan koekappaleet tehtiin juottamalla, eri lisäaineilla. 3. sarjassa pienat hitsattiin, jonka jälkeen hitsin rajaviivalle tehtiin juotto. Kappaleiden geometriat mitattiin ennen testejä, ja osasta kappaleista mitattiin jäännösjännitykset. Kappaleista otettiin hieitä, joista tehtiin kovuusmittaukset ja suoritettiin makro- ja mikrotason tarkastelua liitosprosessin lämmöntuonnin vaikutuksesta. Väsytyskokeiden perusteella kappaleille määritettiin nimelliset ja rakenteelliset väsymisluokat. Tuloksista piirrettiin S-N –käyrät. Liitoksista tehtiin FEA-mallit, joista määritettiin liitoksen rajaviivalle muodostuva jännitys ja 2. sarjan koekappaleiden laskennalliset kestoiät. 1. sarjan juotoksissa oli ongelmana juotoksen tarttuvuus teräksen pintaan. 2. sarjan koetulokset olivat kaikkein parhaita. 3. sarjan kombinaatioliitokset ylsivät kohtalaisiin väsymisluokkiin. 2. sarjan koetulosten perusteella kaarijuotossa on potentiaalia ultralujan rakenneteräksen liittämismenetelmänä. Jatkotutkimuksen tarve on kuitenkin laaja. Tämä työ osoitti, että kaarijuottaminen voi olla vaativa liittämisprosessi, sillä toimiakseen se vaatii varsin tarkat parametrit, ja lisäksi prosessi on melko herkkä olosuhdemuutoksille.

Robotiikkatuoteperheen kehittäminen

Robottiikkatuoteperheeseen kuuluu robottihitsausportaalit, joiden päärunko rakentuu kote-lopalkeista. Koteloprofiilien käyttö on suosittua teollisuuden eri aloilla ja se soveltuu hyvin raskaaseen konepajateollisuuteen. Hitsausrobottiportaalin suunnitteluun liittyy monia eri vaiheita ja valituilla teknisillä ratkaisuilla voidaan vaikuttaa valmistettavan tuotteen hitsin laatuun ja työn onnistumiseen. Hitsausrobottiportaalit ovat usein asiakasräätälöityjä ratkaisuja, jolloin suunnittelutyö sekä valmistusvaihe vaativat runsaasti kapasiteettia. Modulaarisuuden avulla suunnittelu- ja valmistusvaiheita on mahdollista nopeuttaa sekä parantaa tuotteen testausta, huollettavuutta ja laatua. Tässä diplomityössä tutkittiin, miten hitsausrobottiportaalin vaakapuomi käyttäytyy ja taipuu erilaisissa kuormitustilanteissa. Lisäksi työssä määritettiin alkuperäisen koteloprofiilin tilalle uusi optimoitu koteloprofiili sekä tarkasteltiin moduloinnin mahdollistamista robo-tiikkatuoteperheen portaalisovelluksiin.

Controlling full penetration in MAG welding by the application of infrared thermography and neural network

In this study, an infrared thermography based sensor was studied with regard to usability and the accuracy of sensor data as a weld penetration signal in gas metal arc welding. The object of the study was to evaluate a specific sensor type which measures thermography from solidified weld surface. The purpose of the study was to provide expert data for developing a sensor system in adaptive metal active gas (MAG) welding. Welding experiments with considered process variables and recorded thermal profiles were saved to a database for further analysis. To perform the analysis within a reasonable amount of experiments, the process parameter variables were gradually altered by at least 10 %. Later, the effects of process variables on weld penetration and thermography itself were considered. SFS-EN ISO 5817 standard (2014) was applied for classifying the quality of the experiments. As a final step, a neural network was taught based on the experiments. The experiments show that the studied thermography sensor and the neural network can be used for controlling full penetration though they have minor limitations, which are presented in results and discussion. The results are consistent with previous studies and experiments found in the literature.

Synthesis of fluorescent analogues of a-tocopherol as ligands for the human a-tocopherol transfer protein (a-TTP) /

To further understand in vivo localization and trafficking of a-tocopherol (a-Toe), the most biologically active form of vitamin E, between lipid environments, tocopherols are required that can be followed by teclu1iques such as confocal microscopy and fluorescence resonance energy transfer (FRET) assays. To this end, sixteen fluorescent analogues of a-tocopherol (la-d [(1)anthroy loxy -a-tocopherols, A O-a-Toes], 2a-d [w-nitro benzoxadiazole-a-tocopherols, NBD-aToes], 3a-d [w-dansyl-a-tocopherols, DAN-a-Toes], and 4a-d [w-N-methylanthranilamide-atocopherols, NMA-a-TocsD were prepared by substituting fluorescent labels at the terminus of w-functionalized alkyl chains extending from C-2 of the chroman ring while retaining key binding features of the natural ligand. These compounds were prepared starting from (S)-Trolox® acid VIa esterification, protection, and reduction producing the silyl-protected (S)-Trolox aldehyde that was coupled using Wittig chemistry to different w-hydroxyalkylphosphonium bromides. Reduction of the alkene generated the w-hydroxy functionalized 2-n-alkyl intermediates 9a-d having the necessary 2R stereochemistry. A series of functional group manipulations including mesylation, substitution with azide, and hydride reduction provided w-amino functionalized intermediates 12a-d as well. Coupling intermediates 9a-d and 12a-d with the selected fluorophores (9- anthracene carboxylic acid, 4-chloro-7-nitrobenz-2-oxa-l,3-diazole, 5- dimethylaminonapthalene-l-sulfonyl chloride, and I-methyl-2H-3,1-benzoxazine-2,4(1H)dione), followed by deprotection of the phenolic silyl group, gave the desired fluorescent ligands la-d, 2a-d, 3a-d and 4a-d in good yield. Assessment of their binding affinities with recombinant human a-tocopherol transfer protein (ha-TTP) utilizing fluorescent titration binding assays identified competent ligands for further use in protein studies. Compounds Id (C9-AO-a-Toc) and 2d (C9-NBD-a-Toc) both having nonyl alkyl chain extensions between the chromanol and fluorophore were shown to bind specifically to ha-TTP with dissociation constants (KdS) of approximately 280 nM and 55 nM respectively, as compared to 25 nM for the natural ligand 2R,4'R,^'R-a-tocophQxoL.

Armourstone revetments : will standard design criteria prevent failure? /

Bank stabilization structures are used to prevent the loss of valuable land within the urban environment and the decision for the type of structure used depends on the properties of the stream. In the urban areas of Southern Ontario there is a preference for the use of armourstone blocks as bank stabilization. The armourstone revetment is a free standing stone structure with large blocks of stone layered vertically and offset from one another. During fieldwork at Forty Mile Creek in Grimsby, Ontario armourstone failure was identified by the removal of two stones within one column from the wall. Since the footer stones were still in place, toe scour was eliminated as a cause of failure. Through theoretical, field, and experimental work the process of suction has been identified as a mode of failure for the armourstone wall and the process of suction works similarly to quarrying large blocks of rock off bedrock streambeds. The theory of lateral suction has previously not been taken into consideration for the design of these walls. The physical and hydraulic evidence found in the field and studied during experimental work indicate that the armourstone wall is vulnerable to the process of suction. The forces exerted by the flow and the resistance of the block determine the stability of the armourstone block within the wall. The design of the armourstone wall, high surface velocities, and short pulses of faster flowing water within the profile could contribute to armourstone failure by providing the forces needed for suction to occur, therefore adjustments to the design of the wall should be made in order to limit the effect.

Mechanism of tocopherol transfer by human α-tocopherol transfer protein (α-hTTP)

Vitamin E is a well known fat soluble chain breaking antioxidant. It is a general tenn used to describe a family of eight stereoisomers of tocopherols. Selective retention of a-tocopherol in the human circulation system is regulated by the a -Tocopherol Transfer Protein (a-TIP). Using a fluorescently labelled a-tocopherol (NBD-a-Toc) synthesized in our laboratory, a fluorescence resonance energy transfer (FRET) assay was developed to monitor the kinetics of ligand transfer by a-hTTP in lipid vesicles. Preliminary results implied that NBD-a-Toe simply diffused from 6-His-a-hTTP to acceptor membranes since the kinetics of transfer were not responsive to a variety of conditions tested. After a series of trouble shooting experiments, we identified a minor contaminant, E coli. outer membrane porin F (OmpF) that co-purified with 6-His-a-hTTP from the metal affinity column as the source of the problem. In order to completely avoid OmpF contamination, a GST -a-hTTP fusion protein was purified from a glutathione agarose column followed by an on-column thrombin digestion to remove the GST tag. We then demonstrated that a-hTTP utilizes a collisional mechanism to deliver its ligand. Furthennore, a higher rate of a-tocopherol transfer to small unilamellar vesicles (SUV s) versus large unilamellar vesicles (LUV s) indicated that transfer is sensitive to membrane curvature. These findings suggest that ahTTP mediated a-Toc transfer is dominated by the hydrophobic nature of a-hTTP and the packing density of phospholipid head groups within acceptor membranes. Based on the calculated free energy change (dG) when a protein is transferred from water to the lipid bilayer, a model was generated to predict the orientation of a-hTTP when it interacts with lipid membranes. Guided by this model, several hydrophobic residues expected to penetrate deeply into the bilayer hydrophobic core, were mutated to either aspartate or alanine. Utilizing dual polarization interferometry and size exclusion vesicle binding assays, we identified the key residues for membrane binding to be F 165, F 169 and 1202. In addition, the rates of ligand transfer of the u-TTP mutants were directly correlated to their membrane binding capabilities, indicating that membrane binding was likely the rate limiting step in u-TTP mediated transfer of u-Toc. The propensity of u-TTP for highly curved membrane provides a connection to its colocalization with u-Toc in late endosomes.

Localization of monoterpenoid indole alkaloid (MIA) biosynthesis by in situ hybridization (ISH)

Monoterpenoid indole alkaloids (MIA) are among the largest and most complex group of nitrogen containing secondary metabolites that are characteristic of the Apocynaceae plant family including the most notable Catharanthus roseus. These compounds have demonstrated activity as successful drugs for treating various cancers, neurological disorders and cardiovascular conditions. Due to the low yields of these compounds and high pharmacological value, their biosynthesis is a major topic of study. Previous work highlighting the leaf epidermis and leaf surface as a highly active area in MIA biosynthesis and MIA accumulation has made the epidermis a major focus of this thesis. This thesis provides an in-depth analysis of the valuable technique of RNA in situ hybridization (ISH) and demonstrates the application of the technique to analyze the location of the biosynthetic steps involved in the production of MIAs. The work presented in this thesis demonstrates that most of the MIAs of Eurasian Vinca minor, African Tabernaemontana e/egans and five Amsonia species, including North American Amsonia hubrichitii and Mediterranean A. orienta/is, accumulate in leaf wax exudates, while the rest of the leaf is almost devoid of alkaloids. Biochemical studies on Vinca minor displayed high tryptophan decarboxylase (TOe) enzyme activity and protein expression in the leaf epidermis compared to whole leaves. ISH studies aimed at localizing TOe and strictosidine synthase suggest the upper and lower epidermis of V. minor and T. e/egans as probable significant production sites for MIAs that will accumulate on the leaf surface, however the results don't eliminate the possibility of the involvement of other cell types. The monoterpenoid precursor to all MIAs, secologanin, is produced through the MEP pathway occurring in two cell types, the IPAP cells (Gl0H) and epidermal cells (LAMT and SLS). The work presented in this thesis, localizes a novel enzymatic step, UDPG-7-deoxyloganetic acid glucosyltransferase (UGT8) to the IPAP cells of Catharanthus longifolius. These results enable the suggestion that all steps from Gl0H up to and including UGT8 occur in the IPAP cells of the leaf, making the IPAP cells the main site for the majority of secologanin biosynthesis. It also makes the IPAP cells a likely cell type to begin searching for the gene of the uncharacterized steps between Gl0H and UGT8. It also narrows the compound to be transported from the IPAP cells to either 7-deoxyloganic acid or loganic acid, which aids in the identification of the transportation mechanism.

ARTERIAL STIFFNESS IN CHILDREN WITH AND WITHOUT DEVELOPMENTAL COORDINATION DISORDER

The purpose of this study was to determine whether children with potential developmental coordination disorder (p-DCD) demonstrate increased arterial stiffness and thickness compared to age and school matched controls (mean age 14.7 yrs). We also assessed whether these measures differed by sex. Compliance, distensibility, and intima-media thickness (IMT) were measured at the common carotid artery for 28 children with p-DCD and 47 controls. ECG-R-wave-toe pulse wave velocity (PWV) was also measured for 29 children with p-DCD and 45 controls. We found that compared to controls males with p-DCD had significantly higher PWV (3.8±0.2 vs. 4.1±0.3, p=0.001) and lower distensibility (0.82± 0.19 vs. 0.70± 0.17, p=0.034) while females showed no significant differences (p=0.523 and p=0.123 respectively). As a result, it is apparent that sex differences exist with respect to arterial health within this population and that children with p-DCD may be more likely to develop cardiovascular disease later in life.

Photograph - Baie Comeau, welding railway line

A photograph of men working to weld the railway line at Baie Comeau. The caption reads, "Welding railway line as rails joined immediately behind the temporary staff house".

Influence of Interface Surface Geometries In The Tensile Characteristics Of Friction Welded Joints From Aluminium Alloys

Friction welding is a solid state joining process that produces coalescence in materials, using the heat developed between surfaces through a combination of mechanical induced rubbing motion and applied load. In rotary friction welding technique heat is generated by the conversion of mechanical energy into thermal energy at the interface of the work pieces during rotation under pressure. Traditionally friction welding is carried out on a dedicated machine because of its adaptability to mass production. In the present work, steps were made to modify a conventional lathe to rotary friction welding set up to obtain friction welding with different interface surface geometries at two different speeds and to carry out tensile characteristic studies. The surface geometries welded include flat-flat, flat-tapered, tapered-tapered, concave-convex and convex-convex. A comparison of maximum load, breaking load and percentage elongation of different welded geometries has been realized through this project. The maximum load and breaking load were found to be highest for weld formed between rotating flat and stationary tapered at 500RPM and the values were 19.219kN and 14.28 kN respectively. The percentage elongation was found to be highest for weld formed between rotating flat and stationary flat at 500RPM and the value was 21.4%. Hence from the studies it is cleared that process parameter like “interfacing surface geometries” of weld specimens have strong influence on tensile characteristics of friction welded joints

A Comparative Study Of Tensile And Microstructural Characteristics Of Friction Welded Joints And Conventionally Welded Joints Of Aluminium Alloy 6061

Welding of high strength and low weight materials like Aluminium Alloys without any defects by conventional welding techniques is a major challenge in industries. Hence research on solid state welding techniques like Friction stir welding and Friction welding techniques have got much importance in joining of Aluminium alloys. However most of the industries are not changing conventional techniques as skilled workers are available on that area. Most common conventional welding techniques used for joining of Aluminium alloys are Gas welding and Arc welding. Friction welding is a solid-state welding process that generates heat through mechanical friction between a moving and a stationary component with the addition of a lateral force called “upset” to plast ically displace and fuse the materials. In this work, experimental study on tensile and micro structural characteristics of welded joints formed from conventional welding techniques and Rotary friction welding(suitable for weld specimens with circular cross section) has been carried out and the same were compared. The process parameters for arc welding used was 50-70 Amp reverse polarity DC and electrodes of 2.3mm diameter. In Gas welding, the parameters were oxy acetylene neural flame at 3200°C and 3mm electrodes . In the case of friction welding an axial pressure loading of 3Mpa with 5 MPa as upsetting pressure and 500 rpm were used to obtain good welded joints. Tensile characteristic studies of Arc welded joints and Gas welded joints showed 48% and 60 % variations respectively from the maximum load bearing characteristics of parent metal. In the case of friction welded joint, the variation was found to 46%. Micro structural evaluation of conventionally welded joints exhibited clear distinct zones of various weld regions. In the case of friction welded joint micro structural photographs showed comparable features both in parent metal and welded region. Thus the tensile characteristic study and microstructure evaluations proved that friction welded joints are good in both aspects compared to conventionally welded joints.

Explorations of the Practical Issues of Learning Prediction-Control Tasks Using Temporal Difference Learning Methods

There has been recent interest in using temporal difference learning methods to attack problems of prediction and control. While these algorithms have been brought to bear on many problems, they remain poorly understood. It is the purpose of this thesis to further explore these algorithms, presenting a framework for viewing them and raising a number of practical issues and exploring those issues in the context of several case studies. This includes applying the TD(lambda) algorithm to: 1) learning to play tic-tac-toe from the outcome of self-play and of play against a perfectly-playing opponent and 2) learning simple one-dimensional segmentation tasks.