Assessment of trophic change and its probable impact on tropical estuarine environment (the Kodungallur-Azhikode estuary, India)

The cumulative effects of global change, including climate change, increased population density and domestic waste disposal, effluent discharges from industrial processes, agriculture and aquaculture will likely continue and increases the process of eutrophication in estuarine environments. Eutrophication is one of the leading causes of degraded water quality, water column hypoxia/anoxia, harmful algal bloom (HAB) and loss of habitat and species diversity in the estuarine environment. The present study attempts to characterize the trophic condition of coastal estuary using a simple tool; trophic index (TRIX) based on a linear combination of the log of four state variables with supplementary index Efficiency Coefficient (Eff. Coeff.) as a discriminating tool. Numerically, the index TRIX is scaled from 0 to10, covering a wide range of trophic conditions from oligotrophic to eutrophic. Study area Kodungallur-Azhikode Estuary (KAE) was comparatively shallow in nature with average depth of 3.6±0.2 m. Dissolve oxygen regime in the water column was ranged from 4.7±1.3 mgL−1 in Station I to 5.9±1.4 mgL−1 in Station IV. The average nitrate-nitrogen (NO3-N) of KAE water was 470 mg m−3; values ranged from Av. 364.4 mg m−3 at Station II to Av. 626.6 mg m−3at Station VII. The mean ammonium-nitrogen (NH4 +-N) varied from 54.1 mg m−3 at Station VII to 101 mg m−3 at Station III. The average Chl-a for the seven stations of KAE was 6.42±3.91 mg m−3. Comparisons over different spatial and temporal scales in the KAE and study observed that, estuary experiencing high productivity by the influence of high degree of eutrophication; an annual average of 6.91 TRIX was noticed in the KAE and seasonal highest was observed during pre monsoon period (7.15) and lowest during post monsoon period (6.51). In the spatial scale station V showed high value 7.37 and comparatively low values in the station VI (6.93) and station VII (6.96) and which indicates eutrophication was predominant in land cover area with comparatively high water residence time. Eff. Coeff. values in the KAE ranges from −2.74 during monsoon period to the lowest of −1.98 in pre monsoon period. Present study revealed that trophic state of the estuary under severe stress and the restriction of autochthonous and allochthonous nutrient loading should be keystone in mitigate from eutrophication process

INFO2009 - Group 9: Green ICT

A Video Tuturial explaining Green ICT approaches,legal issues and a case study.

Exploratory Study on Occupational Health Exposure to Chemical Agents, in a Public Hospital in Valencia, Venezuela. Preliminar Assessment

Descriptive study that identified chemical agents (AQ) use and training on risk management and waste disposal techniques in a public Hospital in Valencia. A questionnaire was answered by 48 workers. Information obtained was: personal data, occupational history, AQ used; knowledge of risk management and waste disposal. There were 16 occupations from 12 “High Risk” areas. “Adult emergency” was the one with more workers (11 individuals), followed by “sterilization” and “clinical laboratory” (7 each) and oncology (5). The remained areas had less than 8.3% workers. The most used anesthetic agents were: Halothane, Enfluorane and Isofluorane 4.17% each and main antineoplastics used were: Doxorubicin 16.67% and Paclitaxel, 5-Fluoracil and Etoposide, 8.33% each. The most mentioned substances were: alcohol (70.8%) and Chlorine (64.6%). None of the answers regarding knowledge of AQ’ risk management and waste disposal was satisfactory. Statistical associations between training and several variables such as age, time in their job and being or not a professional, resulted non-significant. The correlation between training and the knowledge of AQ’s management was significant (p < 0.001). Participants showed that their knowledge about chemical occupational risk factors they are exposed to is still insufficient. Therefore, this theme should be included in graduate course curricula. These results provide important data and will serve as a pilot research for the follow up Phase II study that will include clinical aspects and environmental and biological monitoring.

Projecte de construcció d'una plataforma especial per al desgel i neteja d'aeronaus a l'aeroport de Girona-Costa Brava

L’objecte d’aquest projecte és definir totes les instal·lacions que caldria construir per tal de dotar l’Aeroport de Girona-Costa Brava d’una plataforma (àrea pavimentada) especial d’estacionament que servís per al desgel i la neteja d’aeronaus, minimitzant al màxim l’impacte sobre el medi ambient i garantint el manteniment de l’operativitat a l’aeroport. El disseny d’aquesta plataforma hauria de permetre recollir l’aigua amb etilenglicol procedent de les operacions de desgel i conduir-la a un dipòsit per al seu posterior tractament i reutilització, a fi de no contaminar el subsòl i les aigües subterrànies. En cas de no utilitzar-se, l’aigua recollida en aquesta plataforma es conduiria a la xarxa d’aigües pluvials

Life cycle analysis of UK coal fired power plants

This paper examines the life cycle GHG emissions from existing UK pulverized coal power plants. The life cycle of the electricity Generation plant includes construction, operation and decommissioning. The operation phase is extended to upstream and downstream processes. Upstream processes include the mining and transport of coal including methane leakage and the production and transport of limestone and ammonia, which are necessary for flue gas clean up. Downstream processes, on the other hand, include waste disposal and the recovery of land used for surface mining. The methodology used is material based process analysis that allows calculation of the total emissions for each process involved. A simple model for predicting the energy and material requirements of the power plant is developed. Preliminary calculations reveal that for a typical UK coal fired plant, the life cycle emissions amount to 990 g CO2-e/kWh of electricity generated, which compares well with previous UK studies. The majority of these emissions result from direct fuel combustion (882 g/kWh 89%) with methane leakage from mining operations accounting for 60% of indirect emissions. In total, mining operations (including methane leakage) account for 67.4% of indirect emissions, while limestone and other material production and transport account for 31.5%. The methodology developed is also applied to a typical IGCC power plant. It is found that IGCC life cycle emissions are 15% less than those from PC power plants. Furthermore, upon investigating the influence of power plant parameters on life cycle emissions, it is determined that, while the effect of changing the load factor is negligible, increasing efficiency from 35% to 38% can reduce emissions by 7.6%. The current study is funded by the UK National Environment Research Council (NERC) and is undertaken as part of the UK Carbon Capture and Storage Consortium (UKCCSC). Future work will investigate the life cycle emissions from other power generation technologies with and without carbon capture and storage. The current paper reveals that it might be possible that, when CCS is employed. the emissions during generation decrease to a level where the emissions from upstream processes (i.e. coal production and transport) become dominant, and so, the life cycle efficiency of the CCS system can be significantly reduced. The location of coal, coal composition and mining method are important in determining the overall impacts. In addition to studying the net emissions from CCS systems, future work will also investigate the feasibility and technoeconomics of these systems as a means of carbon abatement.

Facilities management carbon footprints: an audit of critical elements of management and reporting

Concern for the environmental impact of organizations’ activities has led to the recognition and demand for organizations to manage and report on their carbon footprint. However, there is no limit as to the areas of carbon footprints required in such annual environmental reports. To deliver improvements in the quality of carbon footprint management and reporting, there is a need to identify the main elements of carbon footprint strategy that can be endorsed, supported and encouraged by facility managers. The study investigates carbon footprint elements managed and reported upon by facility manager in the UK. Drawing on a questionnaire survey of 256 facility managers in the UK, the key elements of carbon footprints identified in carbon footprint reports are examined. The findings indicate that the main elements are building energy consumption, waste disposal and water consumption. Business travel in terms of using public transport, air travel and company cars are also recognized as important targets and objectives for the carbon footprint strategy of several FM (facilities management) organizations.

Metal transport parameters of a gneiss saprolitic silty soil for liner design

Diffusion coefficients and retardation factors of two metal cations (Cd2+ and Pb2+) were measured for a compacted Brazilian saprolitic soil derived from gneiss, aiming to assess its geoenvironmental performance as a liner for waste disposal sites. This soil occurs extensively all over the country in very thick layers, but has not been used in liners because of its hydraulic conductivity, higher than 10(-9) m/s when compacted at optimum water content of standard Proctor energy, but which can be reduced by means of appropriate compaction techniques or additives. Batch, column, and diffusion tests were carried out with monospecies synthetic solutions at pH 1, 3, and 5.5. Measured diffusion coefficients varied between 0.5 and 4 X 10(-10) m(2)/s. Retardation factors show that cadmium, a very mobile cation, is not adsorbed at pH I but is significantly retained at pH 3 and pH 5.5, whereas lead is retained at all tested pH values though slightly at pH 1. Estimated retardation factors from batch tests were 1.3-2.3 times those resulting from column tests and at its highest when obtained by diffusion tests; whereas batch tests allow a more complete exposure of the soil grains to the solution, time-dependent nonspecific adsorption may take longer to occur. The importance of contact time was observed and should be considered in further investigations. Its significant retention of metals suggests a promising utilization of this soil as a bottom liner for wastes landfills.

Estudo exploratório da deposição de filmes de diamante em alguns substratos cerâmicos

o presente trabalho é um estudo exploratório a respeito da síntese de filmes de diamante via deposiçãoquímica a vapor (CVD) sobre alguns substratos cerâmicos: diboreto de titânio (TiB2), ítria (Y20a), zircão (ZrSi04), zircônia parcialmente e totalmente estabilizada com ítria (Zr02), pirofilita ( Al2Si4OlO(OHh), .alumina (Al2Oa) e nitreto de boro hexagonal (h-BN). Estes substratos foram produzidos, em sua maioria, a partir da sinterização de pós micrométricos em altas temperaturas. Além do estudo em relação a possíveis candidatos alternativos ao tradicional silício para o crescimento de filmes auto-sustentáveis, procuramos encontrar substratos onde o filme aderisse bem e cujas propriedades tribológicas pudessem ser melhoradas com o recobrimento com filme de diamante.Dentre os materiais selecionados, constatamos que a topografia da superfície relacionada à densidade de contornos de grão, desempenha um papel relevante na nucleação do diamante. Além disso, os materiais que favorecem a formação de carbonetos conduziram a melhores resultados na nucleação e crescimento do filme, indicando que a ação da atmosfera reativa do CVD com o substrato também contribui decisivamente para o processo de nucleação. A partir dos resultados obtidos, concluímos que a aderência do filme de diamante ao zircão é excelente, assim como a qualidade do filme, o que pode serexplorado convenientemente caso as propriedades mecânicas do sinterizado de zircão sejam adequadas. No caso da zircônia parcialmente estabilizada, os resultados obtidos foram surpreendentes e este material poderia substituir o convencional substrato de silício para a deposição de filmes auto-sustentados de diamante, com inúmeras vantagens, dentre elas o fato de ser reutilizável e de não ser necessário ataque com ácidos para remoção do substrato, o que evita a geração de resíduos químicos.

Uma avaliação técnico/econômica da reciclagem de revestimentos asfálticos a frio em usina em área urbana

Trata-se nesta dissertação do emprego da reciclagem a frio de revestimentos asfálticos em usina com a finalidade de aproveitamento como camada de revestimento em vias de tráfego leve e muito leve. São revistos os conceitos de dimensionamento de pavimentos e da dosagem de misturas asfálticas. Dá-se especial atenção ao valor do revestimento asfáltico recuperado e a relevância que a reciclagem tem sobre a redução do descarte de resíduos sólidos no meio ambiente. Identifica-se a importância do emprego da reciclagem sobre o comportamento da sociedade. A metodologia adotada tem por base uma revisão bibliográfica dos registros de trabalhos de reciclagem a frio realizados no Brasil e no exterior. Faz-se um relato dos procedimentos de caracterização dos materiais envolvidos e dos cuidados a serem observados para obter-se um produto final de qualidade. Estão aqui descritos os processos industriais de usinagem da mistura reciclada em plantas industriais fixas. É estabelecida uma proposta de definição da viabilidade econômica de emprego da reciclagem a frio em comparação com o revestimento asfáltico tradicional. Ao final são registrados temas a serem estudados visando tornar a reciclagem a frio de revestimentos asfálticos em usinas de áreas urbanas mais conhecida e considerada como alternativa para a melhoria da qualidade de vida nas cidades.

Desenvolvimento de filtros cerâmicos impregnados com nanopartículas de prata para desinfecção de água potável

Brazil has vast amounts of hydric resources, whose quality has been deteriorating due to pollutant dumping. Household waste disposal is one of the main sources of water pollution, stimulating bacteria proliferation and introducing microorganisms, including those from fecal matter. Conventional water disinfection methods are a solution, but on the downside, they lead to the formation byproducts hazardous to human health. In this study, aiming to develop bactericidal filters for the disinfection of drinking water; silver nanoparticles were deposited on alumina foams through three routes: sputtering DC, dip coating and in situ chemical reduction of silver nitrate. The depositions were characterized through X-ray diffraction, scanning electron microscopy and EDS element mapping. The influence of the depositions on permeability and mechanical properties of the ceramic foams was assessed and, in sequence, a preliminary antibacterial efficiency analysis was carried out. Characterization results indicate that the chemical reduction routes were efficient in depositing homogeneously distributed silver particles and that the concentration of the metallic precursor salt affects size and morphology of the particles. The antibacterial efficiency analysis indicates that the chemical reduction filters have potential for water disinfection

Diagnóstico e avaliação das áreas de destino final dos resíduos sólidos urbanos no estado do rio grande do norte

This work aims to present the diagnosis and the evaluation of areas of final destination of urban solid waste in Rio Grande do Norte (RN) state. The survey was based on the experience of the State of São Paulo, which made its first inventory in 1997, through its Companhia de Tecnologia de Saneamento Ambiental CETESB. The methodology for the structuring of diagnosis was the Índice de Qualidade de Aterros de Resíduo -- IQR, developed by the Institute for Technological Research of São Paulo (ITRP). The calculation is based on the completion of a matrix that contains information about the main features of the site, infrastructure and operating conditions of the area of waste disposal. This study intends to subsidize the state government of Rio Grande do Norte through its State Secretariat of Environment and Water Resources and the Instituto de Desenvolvimento Sustentável e Meio Ambiente do RN (IDEMA), as well as federal, state and municipal authorities, in the definition of public policies for integrated management of municipal solid wastes to take account of environmental preservation and improvement of sanitary conditions of Natal-RN population.

Aplicação integrada de métodos geofísicos em uma área de disposição de resíduos sólidos urbanos em Bauru-SP

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Panorama dos resíduos sólidos urbanos nos municípios de pequeno porte do Brasil

The panorama of Urban Solid Waste (USW) in Brazil, in general lacks information, given the immensity of the country. However, it is from available data that the public executives should define the USW management. To contribute to the choice of a model for the management of USW in small municipalities, this study reviews the related literature, showing an overview of the final disposal of USW in small municipalities. Several data and researches are discussed, concluding that the available data, despite being provided by the public managers, who often attenuate the problem, should be considered for the proposition of policies to encourage the waste treatment

Caracterização geomorfológica e paleogeográfica da plataforma continental adjacente a foz do Rio Apodi-Mossoró, RN/Brasil

The brazilian marginal basins have a huge potential to generate and accumulate petroleum. Incised valleys which are eroded in response to a fall of relative sea level are related to potential reservoir as well, modern drowned-valley estuaries serve as harbors to petroleum and salt industries, fisheries, waste-disposal sites and recreational areas for a significant fraction of the world s population. The combined influence of these factors has produced a dramatic increase in research on modern and ancient incised-valley systems. This research is one expression of this interest. The integrated use of satellites images and high resolution seismic (bathymetry, sides scan sonar) was used on the Apodi River mouth-RN to characterizes the continental shelf This area is located at the Potiguar Basin in the NE Brazilian Equatorial Atlantic margin. Through bathymetric and side scan sonar data processing, a digital Terrain Model was developed, and a detailed geomorphologic analysis was performed. In this way was possible to recognize the geomorphologic framework and differents sismofacies, which may influence this area. A channel extending from the ApodiMossoró river mouth to the shelf edge dominates the investigated area. This structure can be correlated with the former river valley developed during the late Pleistocene sea level fall. This channel has two main directions (NW-SE and NE-SW) probably controlled by the Potiguar Basin structures. The western margin of the channel is relatively steep and pronounced whereas the eastern margin consists only of a gentle slope. Longitudinal bedforms and massive ridges also occur. The first are formed doe to the shelf sediment rework and the reef-like structures probably are relics of submerged beachrock-lines indicating past shoreline positions during the deglacial sea-level rise. The sub-bottom seismic data allow the identification of different sismic patterns and a marcant discontinuity, interpreted as the Upper