Strength prediction of adhesively-bonded scarf repairs in composite structures under bending

This work reports on the experimental and numerical study of the bending behaviour of two-dimensional adhesively-bonded scarf repairs of carbon-epoxy laminates, bonded with the ductile adhesive Araldite 2015®. Scarf angles varying from 2 to 45º were tested. The experimental work performed was used to validate a numerical Finite Element analysis using ABAQUS® and a methodology developed by the authors to predict the strength of bonded assemblies. This methodology consists on replacing the adhesive layer by cohesive elements, including mixed-mode criteria to deal with the mixed-mode behaviour usually observed in structures. Trapezoidal laws in pure modes I and II were used to account for the ductility of the adhesive used. The cohesive laws in pure modes I and II were determined with Double Cantilever Beam and End-Notched Flexure tests, respectively, using an inverse method. Since in the experiments interlaminar and transverse intralaminar failures of the carbon-epoxy components also occurred in some regions, cohesive laws to simulate these failure modes were also obtained experimentally with a similar procedure. A good correlation with the experiments was found on the elastic stiffness, maximum load and failure mode of the repairs, showing that this methodology simulates accurately the mechanical behaviour of bonded assemblies.

Strength prediction and experimental validation of adhesive joints including polyethylene, carbon-epoxy and aluminium adherends

Polyolefins are especially difficult to bond due to their non-polar, non-porous and chemically inert surfaces. Acrylic adhesives used in industry are particularly suited to bond these materials, including many grades of polypropylene (PP) and polyethylene (PE), without special surface preparation. In this work, the tensile strength of single-lap PE and mixed joints bonded with an acrylic adhesive was investigated. The mixed joints included PE with aluminium (AL) or carbon fibre reinforced plastic (CFRP) substrates. The PE substrates were only cleaned with isopropanol, which assured cohesive failures. For the PE CFRP joints, three different surfaces preparations were employed for the CFRP substrates: cleaning with acetone, abrasion with 100 grit sand paper and peel-ply finishing. In the PE AL joints, the AL bonding surfaces were prepared by the following methods: cleaning with acetone, abrasion with 180 and 320 grit sand papers, grit blasting and chemical etching with chromic acid. After abrasion of the CFRP and AL substrates, the surfaces were always cleaned with acetone. The tensile strengths were compared with numerical results from ABAQUS® and a mixed mode (I+II) cohesive damage model. A good agreement was found between the experimental and numerical results, except for the PE AL joints, since the AL surface treatments were not found to be effective.

Information technology service management: an experimental approach towards IT service prediction

Dissertation presented to obtain a Masters degree in Computer Science

Strength prediction of single- and double-lap joints by standard and extended finite element modelling

The structural integrity of multi-component structures is usually determined by the strength and durability of their unions. Adhesive bonding is often chosen over welding, riveting and bolting, due to the reduction of stress concentrations, reduced weight penalty and easy manufacturing, amongst other issues. In the past decades, the Finite Element Method (FEM) has been used for the simulation and strength prediction of bonded structures, by strength of materials or fracture mechanics-based criteria. Cohesive-zone models (CZMs) have already proved to be an effective tool in modelling damage growth, surpassing a few limitations of the aforementioned techniques. Despite this fact, they still suffer from the restriction of damage growth only at predefined growth paths. The eXtended Finite Element Method (XFEM) is a recent improvement of the FEM, developed to allow the growth of discontinuities within bulk solids along an arbitrary path, by enriching degrees of freedom with special displacement functions, thus overcoming the main restriction of CZMs. These two techniques were tested to simulate adhesively bonded single- and double-lap joints. The comparative evaluation of the two methods showed their capabilities and/or limitations for this specific purpose.

Fractional discrete-time signal processing: scale conversion and linear prediction

Nonlinear Dynamics, Vol. 29

New results on fractional linear prediction

Proceedings of the European Control Conference, ECC’01, Porto, Portugal, September 2001

Aplicação da metodologia de “lean management” no processo de desenvolvimento de produto

O presente trabalho de dissertação teve como objetivo a implementação de metodologias de Lean Management e avaliação do seu impacto no processo de Desenvolvimento de Produto. A abordagem utilizada consistiu em efetuar uma revisão da literatura e levantamento do Estado da Arte para obter a fundamentação teórica necessária à implementação de metodologias Lean. Prosseguiu com o levantamento da situação inicial da organização em estudo ao nível das atividades de desenvolvimento de produto, práticas de gestão documental e operacional e ainda de atividades de suporte através da realização de inquéritos e medições experimentais. Este conhecimento permitiu criar um modelo de referência para a implementação de Lean Management nesta área específica do desenvolvimento de produto. Após implementado, este modelo foi validado pela sua experimentação prática e recolha de indicadores. A implementação deste modelo de referência permitiu introduzir na Unidade de Desenvolvimento de Produto e Sistemas (DPS) da organização INEGI, as bases do pensamento Lean, contribuindo para a criação de um ambiente de Respeito pela Humanidade e de Melhoria Contínua. Neste ambiente foi possível obter ganhos qualitativos e quantitativos nas várias áreas em estudo, contribuindo de forma global para um aumento da eficiência e eficácia da DPS. Prevê-se que este aumento de eficiência represente um aumento da capacidade instalada na Organização, pela redução anual de 2290 horas de desperdício (6.5% da capacidade total da unidade) e pela redução significativa em custos operacionais. Algumas das implementações de melhoria propostas no decorrer deste trabalho, após verificado o seu sucesso, extravasaram a unidade em estudo e foram aplicadas transversalmente à da organização. Foram também obtidos ganhos qualitativos, tais como a normalização de práticas de gestão documental e a centralização e agilização de fluxos de informação. Isso permitiu um aumento de qualidade dos serviços prestados pela redução de correções e retrabalho. Adicionalmente, com o desenvolvimento de uma nova ferramenta que permite a monitorização do estado atual dos projetos a nível da sua percentagem de execução (cumprimento de objetivos), prazos e custos, bem como a estimação das datas de conclusão dos projetos possibilitando o replaneamento do projeto bem como a detecção atempada de desvios. A ferramenta permite também a criação de um histórico que identifica o esforço horário associado à realização das atividades/tarefas das várias áreas de Desenvolvimento de Produto e desta forma pode ser usada como suporte à orçamentação futura de atividades similares. No decorrer do projeto, foram também criados os mecanismos que permitem o cálculo de indicadores das competências técnicas e motivações intrínsecas individuais da equipa DPS. Estes indicadores podem ser usados na definição por parte dos gestores dos projetos da composição das equipas de trabalho, dos executantes de tarefas individuais do projeto e dos destinatários de ações de formação. Com esta informação é expectável que se consiga um maior aproveitamento do potencial humano e como consequência um aumento do desempenho e da satisfação pessoal dos recursos humanos da organização. Este caso de estudo veio demonstrar que o potencial de melhoria dos processos associados ao desenvolvimento de produto através de metodologias de Lean Management é muito significativo, e que estes resultam em ganhos visíveis para a organização bem como para os seus elementos individualmente.

Limit Cycle Prediction of Systems with Fractional Controllers and Backlash

This article investigates the limit cycle (LC) prediction of systems with backlash by means of the describing function (DF) when using discrete fractional-order (FO) algorithms. The DF is an approximate method that gives good estimates of LCs. The implementation of FO controllers requires the use of rational approximations, but such realizations produce distinct dynamic types of behavior. This study analyzes the accuracy in the prediction of LCs, namely their amplitude and frequency, when using several different algorithms. To illustrate this problem we use FO-PID algorithms in the control of systems with backlash.

Using data mining with time series data in short-term stocks prediction

Data Mining (DM) methods are being increasingly used in prediction with time series data, in addition to traditional statistical approaches. This paper presents a literature review of the use of DM with time series data, focusing on short- time stocks prediction. This is an area that has been attracting a great deal of attention from researchers in the field. The main contribution of this paper is to provide an outline of the use of DM with time series data, using mainly examples related with short-term stocks prediction. This is important to a better understanding of the field. Some of the main trends and open issues will also be introduced.

Será que a Definição de Síndroma Metabólica pela International Diabetes Federation Melhora a Capacidade Preditora para Doença Coronária e do Espessamento da Íntima-Média Carotídea?

BACKGROUND: Metabolic syndrome (MS) is associated with increased incidence of diabetes and atherosclerotic complications. The new definition of the International Diabetes Federation (IDF) increases the population with this entity, compared to the NCEP ATP III definition. OBJECTIVES: To study the prevalence of coronary artery disease (CAD) and carotid intima-media thickness (IMT) in patients with and without MS, according to the NCEP ATP III and IDF definitions, and the predictive ability of carotid IMT for CAD. METHODS: We studied 270 consecutive patients admitted for elective coronary angiography due to suspicion of CAD. All patients underwent ultrasound study of the carotid arteries to measure IMT (the highest value between the right and left common carotid arteries was used in the analysis). Coronary stenosis of > or =70% (or 50% for the left main coronary artery) was considered significant. RESULTS: By the ATP III definition, 14% of the patients had MS, and these patients had a higher prevalence of CAD (87% vs. 63%, p = 0.004), but no significant difference was found for carotid IMT (1.03 +/- 0.36 mm vs. 0.95 +/- 0.35 mm, p=NS). With the IDF definition, 61% of the patients had MS; this group was slightly older and included more women. There were no differences in terms of CAD (68% vs. 63%) or carotid IMT (0.97 +/- 0.34 vs. 0.96 +/- 0.39 mm). On multivariate analysis, the ATP III definition of MS predicts CAD (OR 4.76, 95% CI 1.71-13.25, p = 0.003), but the IDF definition does not (OR 1.29, 95% CI 0.74-2.27, p = 0.37). On ROC curve analysis, an IMT of > or = 0.95 mm predicts CAD (AUC 0.66, p < 0.001), with a sensitivity of 52% and specificity of 75%. CONCLUSIONS: The new IDF definition increases the population with MS, decreasing the capacity to predict the presence of CAD. In our population, neither the ATP III nor the IDF definition showed differences in terms of carotid IMT. Carotid IMT can predict CAD, but with only modest sensitivity.

Do Spirituality and Faith Make a Difference? Report from the Southern European Psycho-Oncology Study Group

OBJECTIVE: In the last decade, some attention has been given to spirituality and faith and their role in cancer patients' coping. Few data are available about spirituality among cancer patients in Southern European countries, which have a big tradition of spirituality, namely, the Catholic religion. As part of a more general investigation (Southern European Psycho-Oncology Study--SEPOS), the aim of this study was to examine the effect of spirituality in molding psychosocial implications in Southern European cancer patients. METHOD: A convenience sample of 323 outpatients with a diagnosis of cancer between 6 to 18 months, a good performance status (Karnofsky Performance Status > 80), and no cognitive deficits or central nervous system (CNS) involvement by disease were approached in university and affiliated cancer centers in Italy, Spain, Portugal, and Switzerland (Italian speaking area). Each patient was evaluated for spirituality (Visual Analog Scale 0-10), psychological morbidity (Hospital Anxiety and Depression Scale--HADS), coping strategies (Mini-Mental Adjustment to Cancer--Mini-MAC) and concerns about illness (Cancer Worries Inventory--CWI). RESULTS. The majority of patients (79.3%) referred to being supported by their spirituality/faith throughout their illness. Significant differences were found between the spirituality and non-spirituality groups (p ≤ 0.01) in terms of education, coping styles, and psychological morbidity. Spirituality was significantly correlated with fighting spirit (r = -0.27), fatalism (r = 0.50), and avoidance (r = 0.23) coping styles and negatively correlated with education (r = -0.25), depression (r = -0.22) and HAD total (r = -0.17). SIGNIFICANCE OF RESULTS: Spirituality is frequent among Southern European cancer patients with lower education and seems to play some protective role towards psychological morbidity, specifically depression. Further studies should examine this trend in Southern European cancer patients.

Thermographic and visible spectrum camera calibration for marine robotic target detection

Oceans - San Diego, 2013

Adhesive selection for single lap bonded joints: Experimentation and advanced techniques for strength prediction

The integrity of multi-component structures is usually determined by their unions. Adhesive-bonding is often used over traditional methods because of the reduction of stress concentrations, reduced weight penalty, and easy manufacturing. Commercial adhesives range from strong and brittle (e.g., Araldite® AV138) to less strong and ductile (e.g., Araldite® 2015). A new family of polyurethane adhesives combines high strength and ductility (e.g., Sikaforce® 7888). In this work, the performance of the three above-mentioned adhesives was tested in single lap joints with varying values of overlap length (LO). The experimental work carried out is accompanied by a detailed numerical analysis by finite elements, either based on cohesive zone models (CZM) or the extended finite element method (XFEM). This procedure enabled detailing the performance of these predictive techniques applied to bonded joints. Moreover, it was possible to evaluate which family of adhesives is more suited for each joint geometry. CZM revealed to be highly accurate, except for largely ductile adhesives, although this could be circumvented with a different cohesive law. XFEM is not the most suited technique for mixed-mode damage growth, but a rough prediction was achieved.

A Brother or a Sister With CP. How Much it Makes a Difference in Childhood and Adulthood?

Every month we see to be published dozens of scientific papers about etiology and physiopathology of CP, imaging, treatment, survival, quality of life of patients and of mothers (just a few) and so on. Papers dealing with the feelings and the problems of siblings of children and adults with CP in the most important scientific journals are extremely rare. However in internet we can find the sites of the most important Cerebral Palsy Societies, like the British, the Australian and the American ones already devoting a special attention to the issue of siblings; we also can see several interesting blogs of parents sharing their experiences not only with the handicapped child but also with the siblings, even counseling some books written for children giving practical advices how to deal and live with a handicapped sibling. What was a surprise to me were the several sites of adults having a disabled sibling, frequently with CP, in a new situation: without parents to care them.