Internal resonance of an L-shaped beam with a limit stop .1. Free vibration

Real-life structures often possess piecewise stiffness because of clearances or interference between subassemblies. Such an aspect can alter a system's fundamental free vibration response and leads to complex mode interaction. The free vibration behaviour of an L-shaped beam with a limit stop is analyzed by using the frequency response function and the incremental harmonic balance method. The presence of multiple internal resonances, which involve interactions among the first five modes and are extremely complex, have been discovered by including higher harmonics in the analysis. The results show that mode interaction may occur if the higher harmonics of a vibration mode are close to the natural frequency of a higher mode. The conditions for the existence of internal resonance are explored, and it is shown that a prerequisite is the presence of bifurcation points in the form of intersecting backbone curves. A method to compute such intersections by using only one harmonic in the free vibration solution is proposed. (C) 1996 Academic Press Limited

Internal resonance of an L-shaped beam with a limit stop .2. Forced vibration

A limit stop is placed at the elbow of an L-shaped beam whose linear natural frequencies are nearly commensurable. As a result of this hardening device the non-linear system exhibits multiple internal resonances, which involve various degree of coupling between the first five modes of the beam in free vibration. A point load is so placed as to excite several modes and the resulting forced vibration is examined. In the undamped case, three in-phase and two out-of-phase solution branches have been found. The resonance curve is extremely complicated, with multiple branches and interactions between the first four modes. The amplitudes of the higher harmonics are highly influenced by damping, the presence of which can effectively attenuate internal resonances. Consequently parts of the resonance curve may be eliminated, with the resulting response comprising different distinctive branches. (C) 1996 Academic Press Limited

Circular brass foil failed by plugging opposite to direction of incident laser beam

The peripheries of circular foils of 30 mm in diameter and 0.1 mm thick are fixed while their surfaces are subjected to a long pulsed laser over a central region that may vary from 2 mm to 6 mm in diameter. Failure is observed and classified into three stages; they are referred to as thermal bulging, localized shear deformation, and perforation by plugging. A distinct feature of the failure mode is that bulging and plugging occurred in the direction opposite to the incident laser beam. Such a phenomenon can be expected to occur for a laser intensity threshold value of about 0.61 x 10(6) W/cm(2) beyond which local melting of the material begins to take place.

On the velocity of buckle propagation in a beam on a nonlinear elastic-foundation

The paper revisits a simple beam model used by Chater et al. (1983, Proc. IUTAM Symp. Collapse, Cambridge University Press) to examine the dynamics of propagating buckles on it. It was found that, if a buckle is initiated at a constant pressure higher than the propagation pressure of the model (P-p), the buckle accelerates and gradually reaches a constant velocity which depends upon the pressure, while if it is initiated at P-p, the buckle propagates at a velocity which depends upon the initial imperfection. The causes for the difference are also investigated.

Creep behavior of woven roving grp beam in three-point bending

The creep and relaxation behaviour of laminated glass fibre reinforced plastics (GRP) in three-point bending were studied both experimentally and analytically. Creep and relaxation experiments were carried out on eight types of specimens, consisting of glass fibre fabric reinforced epoxy beams. While the bending deflexion and creep strains were measured in the creep tests, the load and relaxation strain were recorded in the relaxation tests. Marked creep effects were seen in the tests, where the environment temperature was 50°C and the period of the measurement was 60 min. An attempt to predict the creep deflexion and relaxation behaviour was made. The transverse shear effect on creep deflexion was taken into account. The predicted results were compared with experimental ones. They were found to be in reasonable agreement, but the linearization assumption, upon which the relaxation behaviour analysis was based, appears to lead to larger inaccuracies in the results.

Investigation on the Interaction of Laser Beam and Metal Powders Conveyed by Coaxial Powder Feeder

In order to investigate the transient thermal stress field in wall-shape metal part during laser direct forming, a FEM model basing on ANSYS is established, and its algorithm is also dealt with. Calculation results show that while the wall-shape metal part is being deposited, in X direction, the thermal stress in the top layer of the wall-shape metal part is tensile stress and in the inner of the wall-shape metal part is compressive stress. The reason causing above-mentioned thermal stress status in the wall-shape metal part is illustrated, and the influence of the time and the processing parameters on the thermal stress field in wall-shape metal part is also studied. The calculation results are consistent with experimental results in tendency.

Mollusks taken by Beam Trawl in the vicinity of Gray's Reef National Marine Sanctuary on the Continental Shelf off Georgia, Southeastern U.S.

Mollusks were sorted from samples of shell hash (obtained as bycatch during NOAA-sponsored studies of larval and juvenile fish distribution), and analyzed to gain qualitative insights on species composition, distribution and habitat affinities of the molluscan fauna on the continental shelf off Georgia. Samples came from beam trawls at 37 stations located in the immediate vicinity and offshore of the Gray’s Reef National Marine Sanctuary (GRNMS) at depths of 4.9 to 103 m. Two hundred sixty-three (263) taxa of mollusks (~58% as dead shells only) were collected, and nearly all (~99%) were identified to the species level. Ninety-seven of these taxa appeared in samples from one or more of the four stations established near the corners of the GRNMS. Samples were highly variable in terms of appearance, volume and species composition of mollusks, reflecting the extreme patchiness of benthic habitats within this region of the continental shelf. With very few exceptions, the mollusks were generally characteristic of either the Carolinian or Caribbean faunal provinces. The Georgia continental shelf, however, was outside the previously reported ranges for at least 16 of the species reported here. Most of these extralimital species were known previously from the East Coast of Florida, and represented northerly range extensions of 1-5° Latitude (110-560 km). One species represented a more significant range extension from the Bahamas and the southern Caribbean, and two represented southerly range extensions, known previously from only as close as off North Carolina. The high incidence of range extensions found in this study and the potential for discovery of additional species are discussed in the context of the diversity and patchiness of benthic habitats on the continental shelf of the region, and the sensitivity of species recruitment to variability in Gulf Stream patterns and global climate change. (PDF contains 52 pages)