FIA potentiometric system based on periodate polymeric membrane sensors for the assessment of ascorbic acid in commercial drinks

Ascorbic acid is found in many food samples. Its clinical and technological importance demands an easyto- use, rapid, robust and inexpensive method of analysis. For this purpose, this work proposes a new flow procedure based on the oxidation of ascorbic acid by periodate. A new potentiometric periodate sensor was constructed to monitor this reaction. The selective membranes were of PVC with porphyrin-based sensing systems and a lipophilic cation as additive. The sensor displayed a near-Nernstian response for periodate over 1.0x10-2–6.0x10-6 M, with an anionic slope of 73.9 ± 0.9 mV decade-1. It was pH independent in acidic media and presented good selectivity features towards several inorganic anions. The flow set-up operated in double-channel, carrying a 5.0x10-4 M IO- 4 solution and a suitable buffer; these were mixed in a 50-cm reaction coil. The overall flow rate was 7 ml min-1 and the injection volume 70 µl. Under these conditions, a linear behaviour against concentration was observed for 17.7–194.0 µg ml-1, presenting slopes of 0.169 mV (mg/l)-1, a reproducibility of ±1.1 mV (n = 5), and a sampling rate of ~96 samples h-1. The proposed method was applied to the analysis of beverages and pharmaceuticals.

Ensaio sobre um sistema de um painel de uma divisória pré-fabricada

O setor da construção civil em Portugal sofre atualmente uma crise, como consequência da crise instalada no país. Além disso, a construção tradicional devido à sua rigidez espacial contribuiu para que os edifícios não se pudessem adaptar de uma forma simples, rápida e económica. Para contrabalançar esses factos a industrialização deverá ser encarada como uma das áreas com maior potencial de crescimento no futuro. A possibilidade de conceber um sistema que se adapta às constantes mudanças das necessidades humanas torna-se um dos grandes desafios da indústria da construção civil onde a pré-fabricação terá um papel fundamental. Neste ensaio estuda-se um sistema de divisórias leves amovíveis pré-fabricadas. No primeiro capítulo deste ensaio é elaborada uma síntese de conceitos que estão relacionados com as divisórias leves pré-fabricadas (industrialização e pré-fabricação), aborda-se a avaliação do sistema previsto ao nível da legislação e os passos a dar para verificação da viabilidade do sistema. No segundo capítulo faz-se uma distinção entre os vários tipos de pré-fabricação, definemse as exigências de desempenho e funcionais do sistema, aborda-se o conceito de coordenação modular e das tolerâncias de construção referindo a sua tremenda importância na pré-fabricação. Na parte final deste capítulo abordam-se exaustivamente as exigências de desempenho das paredes interiores não resistentes. No terceiro capítulo desenvolveu-se o sistema. Descrevem-se todos os componentes do sistema e a justificação da sua utilização. Elaboram-se três pré-avaliações: mecânica, acústica e térmica. Definem-se as ligações a serem utilizadas e pormenorizam-se todos os materiais das ligações. É apresentada uma avaliação económica de custos do sistema. Definem-se os procedimentos de: fabricação, transporte, montagem e desmontagem do sistema. No último capítulo apresentam-se as principais conclusões e os possíveis desenvolvimentos futuros.

Estudo dos desvios detectados pelas imagens portais no cancro da próstata em radioterapia conformacional (3DCRT)

Mestrado em Radioterapia

Transport mechanism in ionic liquid membranes and the study of thiomersal biodegradation

The initial goal of this work was the development of a supported liquid membrane (SLM) bioreactor for the remediation of vaccine production effluents contaminated with a highly toxic organomercurial – thiomersal. Therefore, two main aspects were focused on: 1) the development of a stable supported liquid membrane – using room temperature ionic liquids (RTILs) – for the selective transport of thiomersal from the wastewater to a biological compartment, 2) study of the biodegradation kinetics of thiomersal to metallic mercury by a Pseudomonas putida strain. The first part of the work focused on the evaluation of the physicochemical properties of ionic liquids and on the SLMs’ operational stability. The results obtained showed that, although it is possible to obtain a SLM with a high stability, water possesses nonnegligible solubility in the RTILs studied. The formation of water clusters inside the hydrophobic ionic liquid was identified and found to regulate the transport of water and small ions. In practical terms, this meant that, although it was possible to transport thiomersal from the vaccine effluent to the biological compartment, complete isolation of the microbial culture could not be guaranteed and the membrane might ultimately be permeable to other species present in the aqueous vaccine wastewater. It was therefore decided not to operate the initially targeted integrated system but, instead, the biological system by itself. Additionally, attention was given to the development of a thorough understanding of the transport mechanisms involved in the solubilisation and transport of water through supported liquid membranes with RTILs as well as to the evaluation of the effect of water uptake by the SLM in the transport mechanisms of water-soluble solutes and its effect on SLM performance. The results obtained highlighted the determinant role played by water – solubilised inside the ionic liquids – on the transport mechanism. It became clear that the transport mechanism of water and water-soluble solutes through SLMs with [CnMIM][PF6] RTILs was regulated by the dynamics of water clusters inside the RTIL, rather than by molecular diffusion through the bulk of the ionic liquid. Although the stability tests vi performed showed that there were no significant losses of organic phase from the membrane pores, the formation of water clusters inside the ionic liquid, which constitute new, non-selective environments for solute transport, leads to a clear deterioration of SLM performance and selectivity. Nevertheless, electrical impedance spectroscopy characterisation of the SLMs showed that the formation of water clusters did not seem to have a detrimental effect on the SLMs’ electrical characteristics and highlighted the potential of using this type of membranes in electrochemical applications with low resistance requirements. The second part of the work studied the kinetics of thiomersal degradation by a pure culture of P. putida spi3 strain, in batch culture and using a synthe tic wastewater. A continuous ly stirred tank reactor fed with the synthetic wastewater was also operated and the bioreactor’s performance and robustness, when exposed to thiomersal shock loads, were evaluated. Finally, a bioreactor for the biological treatment of a real va ccine production effluent was set up and operated at different dilution rates. Thus it was possible to treat a real thiomersal-contaminated effluent, lowering the outlet mercury concentration to values below the European limit for mercury effluent discharges.

Fractional order modelling of zero length column desorption response for adsorbents with variable particle sizes

This manuscript analyses the data generated by a Zero Length Column (ZLC) diffusion experimental set-up, for 1,3 Di-isopropyl benzene in a 100% alumina matrix with variable particle size. The time evolution of the phenomena resembles those of fractional order systems, namely those with a fast initial transient followed by long and slow tails. The experimental measurements are best fitted with the Harris model revealing a power law behavior.

Demo abstract: RadiaLE: a framework for benchmarking link quality estimators

Link quality estimation is a fundamental building block for the design of several different mechanisms and protocols in wireless sensor networks (WSN). A thorough experimental evaluation of link quality estimators (LQEs) is thus mandatory. Several WSN experimental testbeds have been designed ([1–4]) but only [3] and [2] targeted link quality measurements. However, these were exploited for analyzing low-power links characteristics rather than the performance of LQEs. Despite its importance, the experimental performance evaluation of LQEs remains an open problem, mainly due to the difficulty to provide a quantitative evaluation of their accuracy. This motivated us to build a benchmarking testbed for LQE - RadiaLE, which we present here as a demo. It includes (i.) hardware components that represent the WSN under test and (ii.) a software tool for the set up and control of the experiments and also for analyzing the collected data, allowing for LQEs evaluation.

Gruta da figueira brava (Arrabida): Geological setting

Separata do Tomo XXXVIII das Memories da Academia das Ciencias de Lisboa (Classe de Ciencias)

Meta-heuristics self-parameterization in a multi-agent scheduling system using case-based reasoning

This paper proposes a novel agent-based approach to Meta-Heuristics self-configuration. Meta-heuristics are algorithms with parameters which need to be set up as efficient as possible in order to unsure its performance. A learning module for self-parameterization of Meta-heuristics (MH) in a Multi-Agent System (MAS) for resolution of scheduling problems is proposed in this work. The learning module is based on Case-based Reasoning (CBR) and two different integration approaches are proposed. A computational study is made for comparing the two CBR integration perspectives. Finally, some conclusions are reached and future work outlined.

Otimização do processo produtivo de extrusão de pisos na E06

O presente trabalho foi elaborado no âmbito da Dissertação Final de Mestrado do curso de Engenharia Mecânica – Gestão Industrial do Instituto Superior de Engenharia do Porto. Este foi realizado numa empresa da indústria de pneus, a Continental Mabor S.A.. Nos dias atuais, a indústria esta cada vez mais competitiva, os custos e os prazos da entrega são cada vez mais reduzidos e a qualidade cada vez mais exigente, assim sendo, é imprescindível uma constante melhoria do sistema produtivo. Este fato fez com que o presente trabalho tivesse como principal objetivo determinar o estado atual e delinear um plano de melhoria para um equipamento (Extrusora de pisos nº6), recentemente instalado na fábrica mas oriundo de outra fábrica do grupo, recorrendo para tal ao Lean Manufacturing e a ferramentas que lhe estão associadas. Inicialmente realizou-se uma análise e diagnóstico ao processo de extrusão de pisos na Extrusora nº6, com o intuito de avaliar todas as suas ineficiências e ainda formular um plano de melhorias para a ineficiência de maior impacto no sistema produtivo. Esta análise foi realizada em diferentes turnos e diferentes equipas de trabalho de forma a se obter uma amostra mais representativa da realidade global. Após esta análise verificou-se que as principais ineficiências eram Setup, conformidade do material, dimensões e encravamentos, entre outros. Sendo que os Setup provocam um tempo de paragem de 101 minutos por turno, escolheu-se esta perturbação como o foco do plano de melhorias a realizar posteriormente. De forma a reduzir os tempos de mudança (Setup), o autor no presente trabalho utilizou ferramentas Lean Manufacturing, principalmente o SMED. Conjuntamente com o SMED ainda foram utilizadas outras ferramentas Lean Manufacturing tais como: 5S, Gestão Visual, Problem Solving e Normalização do Método de Trabalho. Após a implementação de todas estas ferramentas obteve-se uma redução de tempos de mudança de 43% com 1 operador e 71% com 2 operadores, ou seja, reduziu-se de 40,5 minutos gastos por turno para a mudança de fieira para 23,13 min e 11,79 min respetivamente, o que corresponde a um ganho monetário anual de 63.621€ ou 105.045€, respetivamente. Com este trabalho conclui-se que a utilização de ferramentas Lean Manufacturing contribuem para a redução dos desperdícios do processo produtivo. Por isso, espera-se que este estudo seja aplicado na Extrusora nº6 e nas restantes Extrusoras de pisos existentes na fábrica, e num futuro próximo que se realize estudos semelhantes em máquinas com diferentes funções.

Estratégias de resolução de comportamentos de oposição e desafio

Relatório da Prática Profissional Supervisionada Mestrado em Educação Pré-Escolar

Estudo e parametrização das principais proteções elétricas de geradores e transformadores de grupo de uma central hidroelétrica

Nesta dissertação, é realizado o estudo e parametrização dos relés de proteção para geradores e transformadores de grupo de uma central hidroelétrica. É efetuada, também, uma breve abordagem à manutenção e ensaio dos respetivos relés. No fornecimento de Energia Elétrica aos seus consumidores, deve-se ter em consideração todo o funcionamento do Sistema Elétrico de Energia (SEE). Como os SEE são projetados para gerar energia elétrica para responder à carga, é necessário garantir que este assegure o fornecimento de energia elétrica com elevados padrões de qualidade e continuidade de serviço. Assim, as proteções revelam, um papel fulcral na garantia da continuidade de serviço. As proteções são constituídas por equipamentos de proteção nomeadamente, relés de proteção, que são dispositivos cuja função é retirar de serviço os equipamentos em defeito, permitindo que o restante sistema elétrico seja alimentado. Os sistemas de proteção são, assim, de extrema importância, já que têm como função, assegurar, garantir e eliminar anomalias evitando danos nos equipamentos e nos utilizadores/consumidores.

Development of procedures for the simulation of atmospheric flows over complex terrain, using OpenFOAM

The main purpose of this work was the development of procedures for the simulation of atmospheric ows over complex terrain, using OpenFOAM. For this aim, tools and procedures were developed apart from this code for the preprocessing and data extraction, which were thereafter applied in the simulation of a real case. For the generation of the computational domain, a systematic method able to translate the terrain elevation model to a native OpenFOAM format (blockMeshDict) was developed. The outcome was a structured mesh, in which the user has the ability to de ne the number of control volumes and its dimensions. With this procedure, the di culties of case set up and the high computation computational e ort reported in literature associated to the use of snappyHexMesh, the OpenFOAM resource explored until then for the accomplishment of this task, were considered to be overwhelmed. Developed procedures for the generation of boundary conditions allowed for the automatic creation of idealized inlet vertical pro les, de nition of wall functions boundary conditions and the calculation of internal eld rst guesses for the iterative solution process, having as input experimental data supplied by the user. The applicability of the generated boundary conditions was limited to the simulation of turbulent, steady-state, incompressible and neutrally strati ed atmospheric ows, always recurring to RaNS (Reynolds-averaged Navier-Stokes) models. For the modelling of terrain roughness, the developed procedure allowed to the user the de nition of idealized conditions, like an uniform aerodynamic roughness length or making its value variable as a function of topography characteristic values, or the using of real site data, and it was complemented by the development of techniques for the visual inspection of generated roughness maps. The absence and the non inclusion of a forest canopy model limited the applicability of this procedure to low aerodynamic roughness lengths. The developed tools and procedures were then applied in the simulation of a neutrally strati ed atmospheric ow over the Askervein hill. In the performed simulations was evaluated the solution sensibility to di erent convection schemes, mesh dimensions, ground roughness and formulations of the k - ε and k - ω models. When compared to experimental data, calculated values showed a good agreement of speed-up in hill top and lee side, with a relative error of less than 10% at a height of 10 m above ground level. Turbulent kinetic energy was considered to be well simulated in the hill windward and hill top, and grossly predicted in the lee side, where a zone of ow separation was also identi ed. Despite the need of more work to evaluate the importance of the downstream recirculation zone in the quality of gathered results, the agreement between the calculated and experimental values and the OpenFOAM sensibility to the tested parameters were considered to be generally in line with the simulations presented in the reviewed bibliographic sources.

A new approach to assess defragmentation strategies in dynamically reconfigurable FPGAs

Fragmentation on dynamically reconfigurable FPGAs is a major obstacle to the efficient management of the logic space in reconfigurable systems. When resource allocation decisions have to be made at run-time a rearrangement may be necessary to release enough contiguous resources to implement incoming functions. The feasibility of run-time relocation depends on the processing time required to set up rearrangements. Moreover, the performance of the relocated functions should not be affected by this process or otherwise the whole system performance, and even its operation, may be at risk. Relocation should take into account not only specific functional issues, but also the FPGA architecture, since these two aspects are normally intertwined. A simple and fast method to assess performance degradation of a function during relocation and to speed up the defragmentation process, based on previous function labelling and on the application of the Euclidian distance concept, is proposed in this paper.

Poupança de Energia na Pultrusão

Nos dias de hoje, a problemática energética toma um papel de destaque a nível mundial. Devido às elevadas emissões de CO2 dos últimos anos, que promoveram o efeito de estufa e, consequente, aquecimento global, existe a necessidade de reunir esforços de forma a tornar cada vez mais eficiente e racional o uso de energia. Sendo grandes consumidores de energia, a indústria é uma área onde é imprescindível actuar, permitindo obter benefícios a nível ecológico bem como na competitividade do produto. A pultrusão, como processo industrial cada vez mais utilizado no fabrico de perfis estruturais extremamente leves e resistentes é também uma forte consumidora de energia, com vista à cura da resina termoendurecível utilizada no processo. O sistema de aquecimento normalmente utilizado não tem levado em consideração alguns desperdícios de energia perfeitamente evidentes. Neste trabalho, e recorrendo à termografia e ao método de elementos finitos (MEF), foi efectuado um estudo de utilização mais racional da energia, o qual veio a demonstrar alta eficácia permitindo uma poupança energética de cerca de 57%. Para além disso, este estudo permitiu ainda uma redução efectiva do tempo de set-up, incrementando a flexibilidade do processo.

Convergence to the European Energy Policy in European countries: case studies and comparison

Purpose – Our paper aims at analyzing how different European countries cope with the European Energy Policy, which proposes a set of measures (free energy market, smart meters, energy certificates) to improve energy utilization and management in Europe. Design/methodology/approach – The paper first reports the general vision, regulations and goals set up by Europe to implement the European Energy Policy. Later on, it performs an analysis of how some European countries are coping with the goals, with financial, legal, economical and regulatory measures. Finally, the paper draws a comparison between the countries to present a view on how Europe is responding to the emerging energy emergency of the modern world. Findings – Our analysis on different use cases (countries) showed that European countries are converging to a common energy policy, even though some countries appear to be later than others In particular, Southern European countries were slowed down by the world financial and economical crisis. Still, it appears that contingency plans were put into action, and Europe as a whole is proceeding steadily towards the common vision. Research limitations/implications – European countries are applying yet more cuts to financing green technologies, and it is not possible to predict clearly how each country will evolve its support to the European energy policy. Practical implications – Different countries applied the concepts and measures in different ways. The implementation of the European energy policy has to cope with the resulting plethora of regulations, and a company proposing enhancement regarding energy management still has to possess robust knowledge of the single country, before being able to export experience and know-how between European countries. Originality/Value – Even though a few surveys on energy measures in Europe are already part of the state-of-the-art, organic analysis diagonal to the different topics of the European Energy Policy is missing. Moreover, this paper highlights how European countries are converging on a common view, and provides some details on the differences between the countries, thus facilitating parties interesting into cross-country export of experience and technology for energy management.