Study on fatigue and energy-dissipation properties of nanolayered Cu/Nb thin films

Energy dissipation and fatigue properties of nano-layered thin films are less well studied than bulk properties. Existing experimental methods for studying energy dissipation properties, typically using magnetic interaction as a driving force at different frequencies and a laser-based deformation measurement system, are difficult to apply to two-dimensional materials. We propose a novel experimental method to perform dynamic testing on thin-film materials by driving a cantilever specimen at its fixed end with a bimorph piezoelectric actuator and monitoring the displacements of the specimen and the actuator with a fibre-optic system. Upon vibration, the specimen is greatly affected by its inertia, and behaves as a cantilever beam under base excitation in translation. At resonance, this method resembles the vibrating reed method conventionally used in the viscoelasticity community. The loss tangent is obtained from both the width of a resonance peak and a free-decay process. As for fatigue measurement, we implement a control algorithm into LabView to maintain maximum displacement of the specimen during the course of the experiment. The fatigue S-N curves are obtained.

Synthesis of M2AC (M = Ti, V, Cr, Nb, Zr, A = Al, Sn, S) (MAX) carbide phases and study of their physical behavior under extreme conditions

Materials known as Mn+1AXn phases, where n is 1, 2, or 3, and M represents an early transition metal, A an A-group element, and X is either Carbon and/or Nitrogen [1], are fast becoming technologically important materials due to the interesting combination of unique properties. However, a lot of important information about the high temperature and high pressure behavior of many of these compounds is still missing, which needs to be determined systematically. ^ In this dissertation the synthesis of M2AC (M = Ti, V, Cr, Nb, Zr) and A = (Al, Sn, S) compounds by arc melting, vacuum sintering and piston cylinder synthesis is presented along with the synthesis of Zr 2SC, which has been synthesized for first time in bulk form, by piston cylinder technique. The microstructural analysis by electron microscopy and phase analysis by x-ray diffraction is presented next. Finally, a critical analysis of the behavior of these compounds under the application of extreme pressure (as high as 50 GPa) and temperature (≈ 1000°C) is presented. ^ The high pressure studies, up to 50 GPa, showed that these compounds were structurally intact and their bulk moduli ranged from 140 to 190 GPa. The high temperature studies in the inert atmosphere showed that the M 2SnC compounds were unstable above 650°C and the expansion along the a-axis was higher than that along the c-axis, unlike the other phases. M2SC compounds on the other hand showed negligible difference in the thermal expansion along the two axes. The oxidation study revealed that Ti2AC (Al, S) compounds had highest resistance to oxidation while the M2SnC compounds had the least. Furthermore, from the oxidation study of these compounds, which were short time oxidation experiments, it was found that all of these compounds oxidized to their respective binary oxides. ^

Produção de estrutura com gradiente de porosidade a partir da sinterização por plasma da mistura de pós Ti-Nb-Sn

Porous structures are being widely investigated for use in biomedical implants, aiming to mechanically integrate and functionally the implant inside the bone tissue. Moreover, this structure is also important for drugs that can be stored and can induce and accelerate the process of osseointegration. With the purpose to investigate this effect, Ti, Nb and Sn metal powders, were sintered by plasma using a hollow cathode discharge. Sintering was performed in argon plasma set at 4 mbar pressure and temperatures of 500 ° C, 600 ° C and 700 ° C. Samples were also sintered in the electrical resistance furnace at 1200 ° C in order to compare plasma sintering with the conventional method. It was observed that plasma samples sintered with the hollow cathode configuration showed a gradient in porosity, while the samples sintered in the resistive furnace did not. Furthermore, differences in the microstructure of the samples were found, were a surface with higher porosity and ales porous core were obtained at different temperatures. The percolation profile of distilled water and the chemical compositions of the porous layers of the plasma treated samples were the main results obtained. Based on these results, we can conclude that this structure is particularly important for application in the biomedical field such as scaffolds for drug delivery and implants

Estudo de um compósito Nb-15%pCu obtidos por moagem de alta energia e sinterizados por fase líquida

There is great difficulty in forming a composite refractory metal niobium with copper. This is due to the fact that Nb-Cu system is almost mutually immiscible and may be neglected solubility between them. These properties hinder or prevent obtaining homogeneous and high-density structures, conventionally prepared. This study aims to analyze the use of high-energy milling process (MAE) to implement these natural difficulties, with regard to the densification of the sintered bodies. The MAE and the press were used in the preparation of powders, to obtain a fine and homogeneous distribution of the grain size. Four loads Nb and Cu powders containing 15% by weight of Cu were then milled for MAE in a planetary type ball mill under various milling times and speeds. The results obtained by MAE were analyzed by scanning electron microscopy (SEM), according to the parameters of time and grinding speed. The samples were compacted under pressure of 200 MPa, were then sintered in liquid phase in a vacuum furnace at temperatures of 1100 ° C / 60 min and 1200 ° C / 60 min. Then it was used to characterize diffraction of X-rays to identify the phases. The microstructures of the sintered samples were observed and evaluated using scanning electron microscopy (SEM). Vickers Microhardness tests were performed, obtaining higher values for the sintered bodies in the largest of the post milling times and the larger grinding speeds. It was found that the liquid phase sintering of the samples that were processed by MAE produced at the end of a homogeneous and densified structure in 77,4% relative to the value of the theoretical density of the composite

Estudo de duas pseudoligas de Nb-Cu obtidas pela rota da metalurgia do pó

The Nb-Cu pseudoalloys present themselves as potential substitutes for the alloys from a well known system and already commercially applied, as the W-Cu alloys, used in applications such as heat sinks, electrical contacts and coils for the generation of high magnetic fields. Because it is an immiscible system, where there is mutual insolubility and low wettability of the liquid Cu on the Nb surface, the processing route used in this work was the Powder Metallurgy. Two Nb alloys were used, with additions of 10% and 20% in weight of Cu, and times of 20, 30 and 40 hours for the high energy milling of the starting powders. The milling evolution of the powders is presented through the characterization techniques, such as the LASER diffraction for particle size, XRD, SEM, EDS, DSC, dilatometry, TEM and chemical analysis. After the milling, portions of the loads were submitted to the annealing heat treatment. The process used for the samples consolidation was the hot pressing, which has been applied both on some milled powders samples, as on the annealed powders. Subsequent heat treatments were performed in the samples at temperatures of 1000ºC (solid phase) and 1100ºC (in the Cu liquid phase). All sets of consolidated samples, and also the two sets of the heat treated, were analyzed by XRD, SEM, EDS, density and Vickers microhardness. Moreover, other Nb powder samples with 10% and 20% in weight of Cu obtained by simple mechanical mixing, were consolidated, thermally treated and characterized with the same techniques applied to the others, and the results were compared among themselves. Despite the difficulty of consolidation and densification of the two pseudoalloys of the Nb-Cu system of this study, on the route that passes through the HEM, samples were obtained with densities around 90% of the theoretical density. And, on the processing route of which were only mixed, the values reached up to 97%. Therefore, in this work are also emphasized the processes that made possible these results.

Improved electrochemical performance of Sr2Fe1.5Mo0.4Nb0.1O6-δ -Sm0.2Ce0.8O2-δ composite cathodes by a one-pot method for intermediate temperature solid oxide fuel cells

In this paper, Sr₂Fe_1.5Mo_0.4Nb_0.1O_6-δ (SFMNb)-xSm_0.2Ce_0.8O_2-δ (SDC) (x = 0, 20, 30, 40, 50 wt%) composite cathode materials were synthesized by a one-pot combustion method to improve the electrochemical performance of SFMNb cathode for intermediate temperature solid oxide fuel cells (IT-SOFCs). The fabrication of composite cathodes by adding SDC to SFMNb is conducive to providing extended electrochemical reaction zones for oxygen reduction reactions (ORR). X-ray diffraction (XRD) demonstrates that SFMNb is chemically compatible with SDC electrolytes at temperature up to 1100 °C. Scanning electron microscope (SEM) indicates that the SFMNb-SDC composite cathodes have a porous network nanostructure as well as the single phase SFMNb. The conductivity and thermal expansion coefficient of the composite cathodes decrease with the increased content of SDC, while the electrochemical impedance spectra (EIS) exhibits that SFMNb-40SDC composite cathode has optimal electrochemical performance with low polarization resistance (R_p) on the La_0.9Sr_0.1Ga_0.8Mg_0.2O₃ electrolyte. The R_p of the SFMNb-40SDC composite cathode is about 0.047 Ω cm² at 800 °C in air. A single cell with SFMNb-40SDC cathode also displays favorable discharge performance, whose maximum power density is 1.22 W cm^-2 at 800 °C. All results indicate that SFMNb-40SDC composite material is a promising cathode candidate for IT-SOFCs.

Materiais à base de Sr(Ti,Nb)O3 para sensores lambda

Os sensores lambda resistivos possuem as vantagens de simplicidade e menor custo relativamente à utilização generalizada de sensores potenciométricos de oxigénio. Nesse sentido, os titanatos de estrôncio têm sido alvo de diversos estudos. Para a produção de uma relação inequívoca entre a condutividade destes materiais e a pressão parcial de oxigénio é necessária a adição de um dopante dador que suprime a condução eletrónica do tipo-p na região de pressões parciais de oxigénio próximas de ar. Contudo, a adição de um dopante dador produz respostas lentas destes materiais quando densos a variações da pressão parcial de oxigénio. Além da preparação usual dos pós por reação do estado sólido, foram preparadas diversas composições por mecanossíntese. Tal relaciona-se com o fato exaustivamente reportado de as amostras destes materiais, especialmente quando dopados com dadores, apresentarem comportamentos dependentes das condições de processamento. Teve ainda o intuito de avaliar a viabilidade da sua preparação por este método, e consequentemente verificar se este método de preparação, que presumivelmente produzirá pós com composição mais homogénea e mais reativos, permite alterar/manipular a resposta obtida por amostras com eles produzidas. Foram preparados diversos filmes, tipologia muito usada na produção de sensores resistivos, e amostras porosas com diversas composições à base de titanato de estrôncio produzidos com variadas condições de processamento. Foram realizadas diversas caracterizações sobre estes espécimes numa tentativa de melhor compreender as propriedades destes materiais e a dependência destas com parâmetros microestruturais como o tamanho de grão e a porosidade. Foi verificado que os exemplares de titanato de estrôncio não dopado, quer em filmes quer em amostras porosas, apresentam um comportamento elétrico semelhante ao apresentado por amostras densas deste material. Apurou-se ainda, que as suas características apresentam uma variação ténue com a alteração das condições de processamento. Já espécimes de titanato de estrôncio dopados com dador revelam uma forte dependência das suas propriedades com as condições de processamento utilizadas, nomeadamente, a temperatura de sinterização e o tempo de permanência a essa temperatura. Para o fabrico de sensores resistivos de oxigénio poderá ser preferível o recurso a amostras porosas pelo facto de mais facilmente se manipularem as suas características microestruturais e devido à exclusão dos problemas associados à interação entre o substrato de alumina e o filme. As composições não dopadas são as indicadas para esta função se a gama de pressões de oxigénio a avaliar for relativamente pouco extensa sendo aconselhadas as composições dopadas com dador se for pretendida uma medição da pressão parcial de oxigénio em zonas mais extensas correspondentes à queima com deficiência ou excesso de oxigénio. Mesmo em amostras de elevada porosidade poderá ocorrer resposta transiente do material dopado com dador.

Variación fenotípica y correlación de rendimiento con características morfo-agronómicas en una población de maíz (Zea mays L.) variedad NB-6 en la época de primera, Sábana Grande, Managua, 2014.

Con el objetivo de describir variación fenotípica y correlación de rendimiento con características morfo-agronómicas en una población de maíz (zea mays L.) variedad NB-6 en la época de primera, Sábana Grande, Managua, 2014, se estableció un ensayo en la Finca Santa Rosa Sabana Grande, Managua propiedad de la Universidad Nacional Agraria. La muestra consistió en 93 individuos para caracteres del tallo y hoja, diámetro del tallo (DiamT), altura de la mazorca (AltM), número de hojas (Nho), longitud de la hoja (LonHo), ancho de la hoja (AncHo), altura de la planta (AltP), y 393 individuos para rasgos asociados al rendimiento, longitud de la mazorca (LM), diámetro de la mazorca (DM), número de hilera por mazorca (NH), granos por hilera (GH), peso de granos de la mazorca (PGMAZ), peso de 100 granos (P100G) y peso de la mazorca (PMAZ). El análisis de los datos consistió en estadísticos descriptivos: media, desviación estándar, coeficiente de variación, valores máximos y mínimos, así como correlaciones entre variables morfológicas, correlaciones entre variables asociadas al rendimiento. Finalmente mediante regresión paso a paso (stepwise) se determinaron parámetros de estimación del rendimiento en grano a través de las variables PMAZ y GH. La media y desviación estándar para los caracteres evaluados fueron, 2.21±0.21 AltP, 1.14±0.17 AltM, 94.71±8.18 LonHo, 14.33±1.17 Nho,10.51±0.92 AncHo, 22.81±2.53 DiamT, 16.56±1.83 LM,48.22±3.48 DM, 14.39±1.83 NH, 33.85±4.74 GH, 183.65±40.15 PMAZ, 153.20±33.39 PGMAZ, 34.38±6.08 P100G. El coeficiente de variación mostró valores entre 14.88 y 8.13 % para los caracteres de tallo y hoja correspondientes a AltP y Nho respectivamente. Hubo correlación positiva y significativa AltP con AltM y LonHo (0.74, 036) y DiamT y AncHo (0.39). Para los caracteres relacionados al rendimiento el coeficiente de variación mostró valores entre 21.86 y 7.21 correspondiente a PMAZ y PGMAIZ. Se encontró correlación positiva y significativa para la mayoría de variables del rendimiento exceptuando DM con NH que fue significativa y negativa y LM y NH que no mostraron correlación. El PGMAZ mostró correlaciones positivas y significativas, el resto de variables asociadas al rendimiento con valores que oscilaron entre 0.95 y 0.19 la de mayor correlación fue el PMAZ. El peso de la mazorca contribuyó mas (R2 0.99) al ajuste del modelo de estimación seguido por el número de granos por hilera, para la ecuación final: Yij = 0.7705X1 + 0.3470X2, que puede ser utilizada en selección fenotípica inicial.

Parámetros fenotípicos y genéticos de caracteres de la mazorca asociados al rendimiento del cultivo de maíz (Zea mays L.) cv NB-6, en postrera, Managua 2014

Con el propósito de evaluar la influencia del número de hileras en la mazorca de progenitores maternos (10, 12, 14, 16, 18, 20) sobre variables asociadas al rendimiento, estimar grados de asociación fenotípica entre rasgos y su variabilidad genética, se estableció un experimento de campo en bloques completos al azar (BCA) con cuatro réplicas, en la Finca Santa Rosa propiedad de la UNA, en época de postrera del 2014. Las variables analizadas fueron: Longitud de la mazorca (LM), diámetro de la mazorca (DM) , número de granos por hilera (NGH), peso de 100 granos (P100G), numero de hileras por mazorca ( NHM),peso de la mazorca (PM),peso en grano por mazorca (PGM), mediante los procedimientos de SAS, con estadísticos descriptivos, correlaciones de Pearson y análisis de varianza con regresión de los caracteres maternos sobre los de progenie. Los tratamientos que presentaron promedios más altos para LMp, DMp, NHMp, PMp, PGMp fueron los de 14 y 18 hileras. El tratamiento con 16 hileras mostró la más alta variación fenotípica (CV). Las correlaciones fenotípicas de progenies más destacadas fueron: PMp con PGMp y DMp; PMp con NGHp; DMp con PGMp; PMp con NGHp; NGHp con PGMp; y LMp con PMp, todas ellas positivas y altamente significativas. Las correlaciones fenotípicas entre variables de la progenie con progenitor materno más notorias fueron LM, con NHM y P100G. Del análisis de varianza, el factor NHMm fue altamente significativo para LMp y NHMp y en menor grado para DMp y P100Gp. Se estimaron niveles de variabilidad genética importante en rasgos como LMp, NHMp y NGHp, con valores de heredabilidad entre 0.36 y 0.46, los cuales son muy promisorios para programas de mejoramiento genético participativo.

Estudo da hidrogenação para pulverização de ligas à base de terras raras com Nb para eletrodos de hidreto metálico

Tese (Doutorado em Tecnologia Nuclear)

Caracterização de compósitos Nb-20%cu obtidos por moagem de alta energia e sinterizados por fase líquida

In this work, was studied the formation of a composite of the refractory metal niobium with copper, through the process of high-energy milling and liquid phase sintering. The HEM can be used to synthesize composite powders with high homogeneity and fine size particle distribution. It may also produce the solid solubility in immiscible systems such as Nb-Cu, or extend the solubility of systems with limited solubility. Therefore, in the immiscible system Cu-Nb, the high-energy milling was successfully used to obtain the composite powder particles. Initially, the formation of composite particles during the HEM and the effect of preparation technique on the microstructure of the material was evaluated. Four loads of Nb and Cu powders containing 20%wt Cu were synthesized by MAE in a planetary type ball mill under different periods of grinding. The influence of grinding time on the metal particles is evaluated during the process by the withdrawal of samples at intermediate times of milling. After compaction under different forces, the samples were sintered in a vacuum furnace. The liquid phase sintering of these samples prepared by HEM produced a homogeneous and fine grained. The composite particles forming the sintered samples are the addition of a hard phase (Nb) with a high melting point, and a ductile phase (Cu) with low melting point and high thermal and electrical conductivities. Based on these properties, the Nb-Cu system is a potential material for many applications, such as electrical contacts, welding electrodes, coils for generating high magnetic fields, heat sinks and microwave absorbers, which are coupled to electronic devices. The characterization techniques used in this study, were laser granulometry, used to evaluate the homogeneity and particle size, and the X-ray diffraction, in the phase identification and to analyze the crystalline structure of the powders during milling. The morphology and dispersion of the phases in the composite powder particles, as well the microstructures of the sintered samples, were observed by scanning electron microscopy (SEM). Subsequently, the sintered samples are evaluated for density and densification. And finally, they were characterized by techniques of measuring the electrical conductivity and microhardness, whose properties are analyzed as a function of the parameters for obtaining the composite

Determinación de las condiciones de vitrificación del sistema de BaO-TiO₂-Nb₅, con adiciones de AI₂O₃ y B₂O₃, para la generación de precursores dieléctricos

Propósito y Método de estudio: Este estudio se ha basado en la determinación de las condiciones de vitrificación del sistema óxido: BaO-TiO2-Nb2O5 con adiciones de Al2O3 y -B2O3. Este método representa una alternativa para la obtención de fases cristalinas de titanato de niobio, que presenten propiedad dieléctrica, ya que estas fases cristalinas contribuyen al desarrollo vitrocerámico dieléctrico dentro de la industria de la electrónica. Para la caracterización del vidrio y la posterior caracterización del vitrocerámico se utilizaron las técnicas de DRX, ATD y espectroscopia de impedancia, cuyos datos obtenidos se utilizaron para obtener un vidrio estable y someterlo a un tratamiento térmico adecuado para la producción y el control de la cristalización del vitrocerámico, así como también para determinar las fases cristalinas presentes. Conclusiones y contribuciones: Se obtuvieron vidrios estables en el rango de composición (en% peso) 50BaO-25Nb2O3-25TiO2 con adiciones del 5, 10, 15 y 20% en peso de B2O3, mediante un tratamiento térmico a 1450°C por 2 horas para producir un material homogéneo, dado que se obtuvieron vidrio estables solo con la adición de B2O3 se optó por omitir el Al2O3. Posteriormente, se realizaron tratamientos térmicos a los vidrios estables, para inducir su cristalización controlada. Las propiedades dieléctricas de los vitrocerámicos producidos fueron medidas por espectroscopia de impedancia.