Aeroacoustic source measurement methods for characterizing the sound generated by ducted flow devices with higher-order modes.

The International Organization for Standardization (ISO) method 5136 is widely used in industry and academia to determine the sound power radiated into a duct by fans and other flow devices. The method involves placing the device at the center of a long cylindrical duct with anechoic terminations at each end to eliminate reflections. A single off-axis microphone is used on the inlet and outlet sides that can theoretically capture the plane-wave mode amplitudes but this does not provide enough information to fully account for higher-order modes. In this study, the "two-port" source model is formulated to include higher-order modes and applied for the first three modes. This requires six independent surface pressure measurements on each side or "port." The resulting experimental set-up is much shorter than the ISO rig and does not require anechoic terminations. An array of six external loudspeaker sources is used to characterize the passive part of the two-port model and the set-up provides a framework to account for transmission of higher-order modes through a fan. The relative importance of the higher-order modes has been considered and their effect on inaccuracies when using the ISO method to find source sound power has been analyzed.

Improving intermediate pressure turbine performance by using a nonorthogonal stator

Intermediate pressure (IP) turbines in high bypass ratio civil aeroengines are characterized by a significant increase in radius and a low aspect ratio stator. Conventional aerodynamic designs for the IP turbine stator have had leading and trailing edges orthogonal to the hub and casing end walls. The IP turbine rotor, however, is stacked radially due to stress limits. These choices inevitably lead to a substantial gap between the IP stator and rotor at the outer diameter in a duct that is generally diffusing the flow due to the increasing radius. In this low Mach number study, the IP stator is redesigned, incorporating compound sweep so that the leading and trailing edges are no longer orthogonal to the end walls. Computational investigations showed that the nonorthogonal stator reduces the flow diffusion between the stator and rotor, which yields two benefits: The stator trailing edge velocity was reduced, as was the boundary layer growth on the casing end wall within the gap. Experimental measurements confirm that the turbine with the nonorthogonal stator has an increased efficiency by 0.49%, while also increasing the work output by 4.6%, at the design point. © 2014 by ASME.

Predominant expression and cellular distribution of fish Agr2 in renal collecting system

Anterior gradient 2 (Agr2) genes encode secretory proteins, and play significant roles in anterior-posterior patterning and tumor metastasis. Agr2 transcripts were shown to display quite diverse tissue distribution in different species, and little was known about the cellular localization of Agr2 proteins. In this study, we identified an Agr2 homologue from gibe[ carp (Carassius auratus gibelio), and revealed the expression patterns and cellular localization during embryogenesis and in adult tissues. The full-length cDNA of CagAgr2 is 803 nucleotides (nt) with an open reading frame of 510 nt encoding 169 amino acids. The Agr2 C-terminus matches to the class I PDZ-interacting motif, suggesting that it might be a PDZ-binding protein. During embryogenesis, CagAgr2 was found to be transcribed in the mucus-secreting hatching gland from tailbud stage and later in the pharynx region, swim bladder and pronephric duct as revealed by RT-PCR and whole mount in situ hybridization. In the adult fish, its transcription was predominantly confined to the kidney, and lower transcription levels were also found in the intestine, ovary and gills. To further localize the Agr2 protein, the anti-CagAgr2 polyclonal antibody was produced and used for immunofluorescence observation. In agreement with mRNA expression data, the Agr2 protein was localized in the pronephric duct of 3dph larvae. In adult fish, Agr2 protein expression is confined to the renal collecting system with asymmetric distribution along the apical-basolateral axis. The data provided suggestive evidence that fish Agr2 might be involved in differentiation and secretory functions of kidney epithelium. (C) 2009 Elsevier Inc. All rights reserved.

Fridericia dianchiensis sp nov (Enchytraeidae, oligochaeta) from Yunnan Province, China

Fridericia dianchiensis, a new enchytraeid species collected from Yunnan Province, is described here. It is characterized by a combination of the following characters: 1) lateral bundles containing maximum 3 chaetae; 2) esophageal appendages with 3-4 simple, terminal branches; 3) dorsal vessel originating in XX-XXIII; 4) sub-neural glands absent; 5) seminal vesicle large, occupying two segments; 6)clitellum girdle-shaped or gland cells absent between bursal slits and pre-middle ventrally; 7) coelomocytes without refractile vesicles, 8) spermatheca without diverticula and both ampullae broadly united; and 9) long spermathecal ectal duct without gland at the orifice.

A taxonomic study of Oconnorella (Enchytraeidae, Oligochaeta) from Changbaishan Mountain, China

We describe three enchytraeid species, including two new species, from Mt. Changbaishan, Jilin Province, northeastern China. Oconnorella cheni sp. nov. is characterized by a simple spermatheca; absence of the oesophageal appendages and seminal vesicle; and nephridia from 6/7, with a distinct funnel and the efferent duct arising from the anterior part of the postseptale. Oconnorella globula sp. nov. is distinguished by a spermatheca with two diverticula; lack of oesophageal appendages and seminal vesicle; and nephridia from 6/7, with distinct funnel and the efferent duct arising from the mid-ventral or posteroventral part of the postseptale. We redescribe Oconnorella changbaishanensis (Xie et al., 2000) from type and live specimens, and amend some characters that cannot be investigated clearly from mounted specimens. We revise the generic diagnosis of Oconnorella.

Development of a turning mid turbine frame with embedded design-part II: Unsteady measurements

© 2014 by ASME. This paper, the second of two parts, presents a new setup for the two-stage two-spool facility located at the Institute for Thermal Turbomachinery and Machine Dynamics (ITTM) of Graz University of Technology. The rig was designed to reproduce the flow behavior of a transonic turbine followed by a counter-rotating low pressure stage such as those in high bypass aero-engines. The meridional flow path of the machine is characterized by a diffusing S-shaped duct between the two rotors. The role of wide chord vanes placed into the mid turbine frame is to lead the flow towards the low pressure (LP) rotor with appropriate swirl. Experimental and numerical investigations performed on this setup showed that the wide chord struts induce large wakes and extended secondary flows at the LP inlet flow. Moreover, large deterministic fluctuations of pressure, which may cause noise and blade vibrations, were observed downstream of the LP rotor. In order to minimize secondary vortices and to damp the unsteady interactions, the mid turbine frame was redesigned to locate two zero-lift splitters into each vane passage. While in the first part of the paper the design process of the splitters and the time-averaged flow field were presented, in this second part the measurements performed by means of a fast response probe will support the explanation of the time-resolved field. The discussion will focus on the comparison between the baseline case (without splitters) and the embedded design.

Development of a turning mid turbine frame with embedded design-part I: Design and steady measurements

© 2014 by ASME. The paper presents a new setup for the two-stage two-spool facility located at the Institute for Thermal Turbomachinery and Machine Dynamics (ITTM) of Graz University of Technology. The rig was designed in order to simulate the flow behavior of a transonic turbine followed by a counter-rotating low pressure (LP) stage like the spools of a modern high bypass aeroengine. The meridional flow path of the machine is characterized by a diffusing S-shaped duct between the two rotors. The role of turning struts placed into the mid turbine frame is to lead the flow towards the LP rotor with appropriate swirl. Experimental and numerical investigations performed on the setup over the last years, which were used as baseline for this paper, showed that wide chord vanes induce large wakes and extended secondary flows at the LP rotor inlet flow. Moreover, unsteady interactions between the two turbines were observed downstream of the LP rotor. In order to increase the uniformity and to decrease the unsteady content of the flow at the inlet of the LP rotor, the mid turbine frame was redesigned with two zero-lifting splitters embedded into the strut passage. In this first part of the paper the design process of the splitters and its critical points are presented, while the time-averaged field is discussed by means of five-hole probe measurements and oil flow visualizations. The comparison between the baseline case and the embedded design configuration shows that the new design is able to reduce the flow gradients downstream of the turning struts, providing a more suitable inlet condition for the low pressure rotor. The improvement in the flow field uniformity is also observed downstream of the turbine and it is, consequently, reflected in an enhancement of the LP turbine performance. In the second part of this paper the influence of the embedded design on the time-resolved field is investigated.

Fridericia nanningensis, a new terrestrial enchytraeid species (Oligochaeta) from southwestern China

Fridericia nanningensis, a new species from wetland soil of Nanhu Park, Nanning city, the capital of Guangxi Zhuang Autonomous Region in southwest China, is described. It is characterized by 2-4 chaetae per bundle, poorly-developed clitellar glands, slender, unbranched peptonephridia, and spermathecae with 2 ampullar diverticula, a deep constriction in the middle of the ampulla and one large ectal gland. It is closely related to the European species, F. alata Nielsen & Christensen, 1959 and the East European species, F. tubulosa Dozsa-Farkas, 1972 by the shape of peptonephridia and the undeveloped clitellar glands. It differs from F. alata by its shorter body length and fewer chaetae per bundle, its type of coelomocytes (type "c"), its deep constriction in the middle of the spermathecae ampulla and a larger ectal gland, and it differs from F. tubulosa by its pale epidermal glands, its more anterior origin of the dorsal vessel, a deep constriction in the middle of the spermathecae ampulla, shorter ectal duct, and only one ectal gland at the spermathecal orifice.

交变流动中压力速度之间相位差对突变截面损失的影响分析

从弱非线性热声理论出发,给出交变流动中突变截面阻力系数的定义以及考察方法。通过PIV(粒子成像测速仪)测量与CFD计算结果的对比,验证了CFD计算结果的可靠性。进而利用CFD模拟考察了交变流动中压力与速度之间相位差对突变截面局部损失的影响,观察到产生这种影响的流场内部流动机制。分析表明,阻力特性确实对声场压力与速度之间的相位差存在依赖性,但这种依赖性会随着非线性的增强而减少。

管道内一氧化碳和空气预热混合物的爆燃特性

为了安全回收煤气余热,实验研究了不同初始温度下的一氧化碳和空气混合气体在设置障碍物的管道中的爆燃特性。测量了爆燃压力和火焰速度,分析了化学当量比和温度对爆燃的影响。结果表明:爆燃压力和火焰速度在障碍物段快速提高;一氧化碳当量比为1.1时爆燃的强度最大;初始温度升高后,压力提高逐渐减缓,最大火焰速度下降,但仍大于550 m/s,传播时间先快速增加后平稳。

Enhancements of the simulation method on the edge effect in resin transfer molding processes

In resin transfer molding processes, small clearances exist between the fiber preform and the mold edges, which result in a preferential resin flow in the edge channel and then disrupt the flow patterns during the mold filling stage. A mathematical model including the effect of cavity thickness on resin flow was developed for flow behavior involving the interface between an edge channel and a porous medium. According to the mathematical analysis of momentum equations in a fully developed rectangular duct and formulations of the equivalent edge permeability, comparing with three-dimensional Navier-Stokes equations, the governing equations were modified in the edge channel. The volume of fluid (VOF) method was applied to track the flow front. A simple case is numerically simulated using the modified governing equations. The effects of edge channel width and cavity thickness on flow front and inlet pressure are analyzed, and the evolution characteristics of simulated results are in agreement with the experimental results. (c) 2007 Elsevier B.V. All rights reserved

Biodegradation of poly(L-lactide-co-glycolide) tube stents in bile

The objective of this study was to evaluate degradation behavior and the feasibility of biodegradable polymeric stents in common bile duct (CBD) repair and reconstruction. Various molar ratios of lactide (LA) and glycolide (GA) in poly(L-lactide-co-glycolide) (PLGA) were synthesized and processed into a circular tubing of similar to 10.0 mm outer diameter and a wall thickness of about 2.0 mm.

A simple and low-cost airlift photobioreactor for microalgal mass culture

A simple, low-cost, and efficient airlift photobioreactor for microalgal mass culture was designed and developed. The reactor was made of Plexiglas, and composed of three major parts: outer tube, draft tube and air duct. The fluid-dynamic characteristics of the airlift reactor were studied. The system proved to be well suited to the mass cultivation of a marine microalga, Chlorella sp. In batch culture, the biomass volumetric output rate of 0.21 g l(-1) d(-1) was obtained at the superficial gas velocity of 4 mm s(-1) in the draft tube.

Energy storage systems for wave energy converters and microgrids

The thesis initially gives an overview of the wave industry and the current state of some of the leading technologies as well as the energy storage systems that are inherently part of the power take-off mechanism. The benefits of electrical energy storage systems for wave energy converters are then outlined as well as the key parameters required from them. The options for storage systems are investigated and the reasons for examining supercapacitors and lithium-ion batteries in more detail are shown. The thesis then focusses on a particular type of offshore wave energy converter in its analysis, the backward bent duct buoy employing a Wells turbine. Variable speed strategies from the research literature which make use of the energy stored in the turbine inertia are examined for this system, and based on this analysis an appropriate scheme is selected. A supercapacitor power smoothing approach is presented in conjunction with the variable speed strategy. As long component lifetime is a requirement for offshore wave energy converters, a computer-controlled test rig has been built to validate supercapacitor lifetimes to manufacturer’s specifications. The test rig is also utilised to determine the effect of temperature on supercapacitors, and determine application lifetime. Cycle testing is carried out on individual supercapacitors at room temperature, and also at rated temperature utilising a thermal chamber and equipment programmed through the general purpose interface bus by Matlab. Application testing is carried out using time-compressed scaled-power profiles from the model to allow a comparison of lifetime degradation. Further applications of supercapacitors in offshore wave energy converters are then explored. These include start-up of the non-self-starting Wells turbine, and low-voltage ride-through examined to the limits specified in the Irish grid code for wind turbines. These applications are investigated with a more complete model of the system that includes a detailed back-to-back converter coupling a permanent magnet synchronous generator to the grid. Supercapacitors have been utilised in combination with battery systems for many applications to aid with peak power requirements and have been shown to improve the performance of these energy storage systems. The design, implementation, and construction of coupling a 5 kW h lithium-ion battery to a microgrid are described. The high voltage battery employed a continuous power rating of 10 kW and was designed for the future EV market with a controller area network interface. This build gives a general insight to some of the engineering, planning, safety, and cost requirements of implementing a high power energy storage system near or on an offshore device for interface to a microgrid or grid.

Discoplana malagasensis sp. nov. a New Turbellarian (Platyhelminthes: Polycladida: Leptoplanidae) symbiotic in an ophiuroid (Echinodermata), with a cladistic analysis of the Discoplana/Euplana species

A new species of polyclad flatworm from Papua New Guinea is described. It is found symbiotic in the ophiuroid Ophiothrix purpurea von Martens, 1867 (Echinodermata: Ophiuroidea). Apparently it belongs to the taxon Discoplana Bock, 1913 and can be distinguished from the six previously described Discoplana species by its very short ejaculatory duct and a penial papilla covered with a penial sheath, but without any true sclerotised structures such as a stylet or spines. The cladistic analysis of the Discoplana/Euplana species, based on morphological features and including two outgroups, reveals that all species of Discoplana, except D. pacificola, form a monophyletic taxon, that is not a synonym of Euplana Girard, 1893. Therefore the name Discoplana is conserved and the new species will be described as Discoplana malagasensis sp. nov. A key for the Discoplana/Euplana group is provided. In this key the biogeographical distribution and possible synonyms are given.