On a control design to an AFM microcantilever beam, operating in a tapping-mode, with irregular behavior

In last decades, control of nonlinear dynamic systems became an important and interesting problem studied by many authors, what results the appearance of lots of works about this subject in the scientific literature. In this paper, an Atomic Force Microscope micro cantilever operating in tapping mode was modeled, and its behavior was studied using bifurcation diagrams, phase portraits, time history, Poincare maps and Lyapunov exponents. Chaos was detected in an interval of time; those phenomena undermine the achievement of accurate images by the sample surface. In the mathematical model, periodic and chaotic motion was obtained by changing parameters. To control the chaotic behavior of the system were implemented two control techniques. The SDRE control (State Dependent Riccati Equation) and Time-delayed feedback control. Simulation results show the feasibility of the bothmethods, for chaos control of an AFM system. Copyright © 2011 by ASME.

Forced oscillations with continuum models of atomic force microscopy

The dynamics of the AFM-atomic force microscope follows a model based in a Timoshenko cantilever beam with a tip attached at the free end and acting with the surface of a sample. General boundary conditions arise when the tip is either in contact or non-contact with the surface. The governing equations are given in matrix conservative form subject to localized loads. The eigenanalysis is done with a fundamental matrix response of a damped second-order matrix differential equation. Forced responses are found by using a Galerkin approximation of the matrix impulse response. Simulations results with harmonic and pulse forcing show the filtering character and the effects of the tip-sample interaction at the end of the beam. © 2012 American Institute of Physics.

Tilted and Short Implants Supporting Fixed Prosthesis in an Atrophic Maxilla: A 3D-FEA Biomechanical Evaluation

Purpose: This study compared the biomechanical behavior of tilted long implant and vertical short implants to support fixed prosthesis in an atrophic maxilla. Materials and Methods: The maxilla model was built based on a tomographic image of the patient. Implant models were based on micro-computer tomography imaging of implants. The different configurations considered were M4S, four vertical anterior implants; M4T, two mesial vertical implants and two distal tilted (45°) implants in the anterior region of the maxilla; and M6S, four vertical anterior implants and two vertical posterior implants. Numerical simulation was carried out under bilateral 150N loads applied in the cantilever region in axial (L1) and oblique (45°) (L2) direction. Bone was analyzed using the maximum and minimum principal stress (σmax and σmin), and von Mises stress (σvM) assessments. Implants were analyzed using the σvM. Results: The higher σmax was observed at: M4T, followed by M6S/L1, M6S/L2, M4S/L2, and M4S/L1 and the higher σvM: M4T/L1, M4T/L2 and M4S/L2, M6S/L2, M4S/L1, and M6S/L1. Conclusions: The presence of distal tilted (all-on-four) and distal short implants (all-on-six) resulted in higher stresses in both situations in the maxillary bone in comparison to the presence of vertical implants (all-on-four). © 2013 Wiley Periodicals, Inc.

Utilização de modelos de falhas na metodologia dos observadores de estado para detecção de trincas em sistemas contínuos

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Projeto de controladores robustos para aplicações em estruturas inteligentes utilizando desigualdades matriciais lineares

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Determinação da variação de rigidez em placas, através da metodologia dos observadores de estados

Pós-graduação em Engenharia Mecânica - FEIS

Uso de absorvedores de vibrações eletromecânicos lineares e não-lineares em sistemas não-lineares e não-ideais

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Dinâmica não linear, caos, e controle na microscopia de força atômica

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Caos e controle de microviga em balanço de um microscópio de força atômica, operando em modo intermitente, na ressonância

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Comportamento mecânico de sistemas prótese/implante em região dos elementos finitos e interferometria holográfica

Pós-graduação em Odontologia - FOAR

Análise fotoelástica de tensões em próteses obturadoras palatinas implantorretidas, sobre implantes paralelos ou inclinados, associados a diferentes tipos de sistemas de retenção

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Análise fotoelástica da distribuição de tensão de diferentes materiais de revestimento oclusal em prótese protocolo do tipo Branemark

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência do número e inclinação dos implantes para a ancoragem de prótese fixa em maxila atrófica: estudo comparativo com elementos finitos 3D

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação fotoelástica de overdentures mandibulares sobre implantes com três diferentes sistemas de retenção e prótese protocolo de Branemark

Pós-graduação em Odontologia - FOA

Avaliação da distribuição de tensões em próteses do tipo protocolo mandibular para carregamento imediato por meio do MEF-3D

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)