Residual stresses in titanium nitride thin films obtained with step variation of substrate bias voltage during deposition

In this work, a series of depositions of titanium nitride (TiN) films on M2 and D2 steel substrates were conducted in a Triode Magnetron Sputtering chamber. The temperature; gas flow and pressure were kept constant during each run. The substrate bias was either decreased or increased in a sequence of steps. Residual stress measurements were later conducted through the grazing X-ray diffraction method. Different incident angles were used in order to change the penetration depth and to obtain values of residual stress at different film depths. A model described by Dolle was adapted as an attempt to calculate the values of residual stress at each incident angle as a function of the value from each individual layer. Stress results indicated that the decrease in bias voltage during the deposition has produced compressive residual stress gradients through the film thickness. On the other hand, much less pronounced gradients were found in one of the films deposited with increasing bias voltage. (C) 2010 Elsevier B.V. All rights reserved.

Modeling of Plastic Deformation Effects in Ferromagnetic Thin Films

To explain the magnetic behavior of plastic deformation of thin magnetic films (Fe and permalloy) on an elastic substrate (nitinol), it is noted that unlike in the bulk, the dislocation density does not increase dramatically because of the dimensional constraint. As a result, the resulting residual stress, even though strain hardening is limited, dominates the observed magnetic behavior. Thus, with the field parallel to the stress axis, the compressive residual stress resulting from plastic deformation causes a decrease in remanence and an increase in coercivity; and with the field perpendicular to the stress axis, the resulting compressive residual stress causes an increase in remanence and a decrease in coercivity. These elements have been inserted into the model previously developed for plastic deformation in the bulk, producing the aforementioned behavior, which has been observed experimentally in the films.

The low fertility of repeat-breeder cows during summer heat stress is related to a low oocyte competence to develop into blastocysts

It was hypothesized the lower fertility of repeat-breeder (RB) Holstein cows is associated with oocyte quality and this negative effect is enhanced during summer heat stress (HS). During the summer and the winter, heifers (H; n = 36 and 34, respectively), peak-lactation (PL; n = 37 and 32, respectively), and RB (n = 36 and 31, respectively) Holstein cows were subjected to ovum retrieval to assess oocyte recovery, in vitro embryonic developmental rates, and blastocyst quality [terminal deoxynucleotidyl transferase-mediated dUTP nick end labeling (TUNEL)-positive cells and total cell number]. The environmental temperature and humidity, respiration rate, and cutaneous and rectal temperatures were recorded in both seasons. The summer HS increased the respiration rate and the rectal temperature of PL and RB cows, and increased the cutaneous temperature and lowered the in vitro embryo production of Holstein cows and heifers. Although cleavage rate was similar among groups [H = 51.7% +/- 4.5 (n = 375), PL = 37.9% +/- 5.1 (n = 390), RB = 41.9% +/- 4.5 (n = 666)], blastocyst rate was compromised by HS, especially in RB cows [H = 30.3% +/- 4.8 (n = 244) vs. 23.3% +/- 6.4 (n = 150), PL = 22.0% +/- 4.7 (n = 191) vs. 14.6% +/- 7.6 (n = 103), RB = 22.5% +/- 5.4 (n = 413) vs. 7.9% +/- 4.3 (n = 177)]. Moreover, the fragmentation rate of RB blastocysts was enhanced during the summer, compared with winter [4.9% +/- 0.7 (n = 14) vs. 2.2% +/- 0.2 (n = 78)] and other groups [H = 2.5% +/- 0.7 (n = 13), and PL = 2.7% +/- 0.6 (n = 14)] suggesting that the association of RB fertility problems and summer HS may potentially impair oocyte quality. Our findings provide evidence of a greater sensitivity of RB oocytes to summer HS.

CO(2) Laser (10.6 mu m) Parameters for Caries Prevention in Dental Enamel

Although CO(2) laser irradiation can decrease enamel demineralisation, it has still not been clarified which laser wavelength and which irradiation conditions represent the optimum parameters for application as preventive treatment. The aim of the present explorative study was to find low-fluence CO(2) laser (lambda = 10.6 mu m) parameters resulting in a maximum caries-preventive effect with the least thermal damage. Different laser parameters were systematically evaluated in 3 steps. In the first experiment, 5 fluences of 0.1, 0.3, 0.4, 0.5 and 0.6 J/cm(2), combined with high repetition rates and 10 mu s pulse duration, were chosen for the experiments. In a second experiment, the influence of different pulse durations (5, 10, 20, 30 and 50 mu s) on the demineralisation of dental enamel was assessed. Finally, 3 different irradiation times (2, 5 and 9 s) were tested in a third experiment. In total, 276 bovine enamel blocks were used for the experiments. An 8-day pH-cycling regime was performed after the laser treatment. Demineralisation was assessed by lesion depth measurements with a polarised light microscope, and morphological changes were assessed with a scanning electron microscope. Irradiation with 0.3 J/cm(2), 5 mu s, 226 Hz for 9 s (2,036 overlapping pulses) increased caries resistance by up to 81% compared to the control and was even significantly better than fluoride application (25%, p < 0.0001). Scanning electron microscopy examination did not reveal any obvious damage caused by the laser irradiation. Copyright (C) 2009 S. Karger AG, Basel

Locus coeruleus mediates cold stress-induced polycystic ovary in rats

Previous reports about the rat ovary have shown that cold stress promotes ovarian morphological alterations related to a polycystic ovary (PCO) condition through activation of the ovarian sympathetic nerves. Because the noradrenergic nucleus locus coeruleus (LC) is activated by cold stress and synaptically connected to the preganglionic cell bodies of the ovarian sympathetic pathway, this study aimed to evaluate the LC`s role in cold stress-induced PCO in rats. Ovarian morphology and endocrine and sympathetic functions were evaluated after 8 wk of chronic intermittent cold stress (4 C, 3 h/d) in rats with or without LC lesion. The effect of acute and chronic cold stress upon the LC neuron activity was confirmed by Fos protein expression in tyrosine hydroxylase-immunoreactive neurons. Cold stress induced the formation of follicular cysts, type III follicles, and follicles with hyperthecosis alongside increased plasma estradiol and testosterone levels, irregular estrous cyclicity, and reduced ovulation. Considering estradiol release in vitro, cold stress potentiated the ovarian response to human chorionic gonadotropin. Ovarian norepinephrine (NE) was not altered after 8 wk of stress. However, LC lesion reduced NE activity in the ovary of cold-stressed rats, but not in controls, and prevented all the cold stress effects evaluated. Cold stress increased the number of Fos/tyrosine hydroxylase-immunoreactive neurons in the LC, but this effect was more pronounced for acute stress as compared with chronic stress. These results show that cold stress promotes PCO in rats, which apparently depends on ovarian NE activity that, under this condition, is regulated by the noradrenergic nucleus LC.

Crescimento, teores e acúmulo de nutrientes em plantas de milho fertirrigadas com água residuária do beneficiamento de frutos de café

A cultura do cafeeiro sempre ocupou lugar de destaque na economia do país, dada sua importância na área econômica e social, buscando cada vez mais, um mercado diferenciado, com novas tecnologias para a melhoria da qualidade da bebida. A atividade de lavagem e despolpa de frutos do cafeeiro, necessária para a redução do custo de secagem e a melhoria da qualidade de bebida, é geradora de grandes volumes de resíduos sólidos e líquidos, ricos em material orgânico e inorgânico. A água residuária da atividade de beneficiamento do café (ARC) é gerada anualmente em grande volume no Espírito Santo, e aliado aos nutrientes existentes nesse efluente indica a sua viabilidade de reaproveitamento na fertirrigação de culturas agrícolas. O objetivo do presente trabalho foi avaliar o efeito de diferentes doses de água residuária de café no crescimento, na absorção e interação entre nutrientes e no estado nutricional do milho. Para tanto, foi conduzido um experimento em casa de vegetação utilizando-se o delineamento experimental inteiramente casualizado, onde foram aplicadas 7 doses de ARC, com 3 repetições, em unidades experimentais constituídas por vasos com 2 dm³ de solo. As doses foram equivalentes a 0,00, 15,17, 30,35, 45,52, 60,70, 75,87 e 91,05 litros de ARC por m² de solo. Realizou-se a semeadura de cinco sementes de milho híbrido BR 206 por vaso e cinco dias após a germinação das plantas foi feito o desbaste, mantendo-se três plantas por vaso. Aos trinta dias após a germinação determinou-se o diâmetro do caule (DC), área foliar (AF), matéria seca da parte aérea (MSPA), matéria seca do sistema radicular (MSR), relação parte aérea/raiz (MSPA/MSR), razão massa radicular (matéria seca raiz/matéria seca total) e razão área foliar (área foliar/matéria seca total). Na parte aérea das plantas foi determinado os teores dos macronutrientes (N, P, K, Ca, Mg e S). Os dados foram submetidos a análise de variância e as variáveis em função das doses de ARC submetidas a análise de regressão. Para as variáveis dependentes foi calculado o coeficiente de correlação linear de Pearson. A ARC serviu como fonte de nutrientes para as plantas de milho, aumentou o rendimento da maioria das variáveis de crescimento e os teores de N, K e S. Porém diminuiu o teor de Ca, Mg e P da parte aérea das plantas além de indicar que altas doses promovem desbalanceamento na relação entre nutrientes.

Perfis de tensão residual do aço duplex UNS S32304 submetido a diferentes processos de soldagem TIG e condições de tratamento térmico

Visando a aplicação do aço UNS S32304 em embalados para transporte de material radioativo, amostras soldadas por processo TIG, com diferentes gases de proteção, foram submetidas a tratamentos térmicos nas temperaturas de 475°C, 600°C e 750°C por 8 horas, seguidas de resfriamento ao ar, a fim de analisar o efeito de temperaturas críticas no perfil de tensões residuais e microestrutura. A difratometria de raios X foi utilizada para determinação das tensões residuais, em diferentes condições (amostras como recebidas e apenas tratadas termicamente) e o perfil de tensões residuais total das amostras soldadas é apresentado para cada fase (austenita e ferrita). As tensões residuais das fases foram determinadas pela técnica sen2ψ, utilizando um difratômetro com fonte de radiação CuKα (<λ

Thermal Residual Stresses in Functionally Graded Structures: a Didactic Case Study

Conferência: 2nd Experiment at International Conference - 18-20 September 2013

Mechanical behavior and localized failure modes in a porous basalt from the Azores

Basaltic rocks are the main component of the oceanic upper crust, thus of potential interest for water and geothermal resources, storage of CO2 and volcanic edifice stability. In this work, we investigated experimentally the mechanical behavior and the failure modes of a porous basalt, with an initial connected porosity of 18%. Results were acquired under triaxial compression experiments at confining pressure in the range of 25-200 MPa on water saturated samples. In addition, a purely hydrostatic test was also performed to reach the pore collapse critical pressure P*. During hydrostatic loading, our results show that the permeability is highly pressure dependent, which suggests that the permeability is mainly controlled by pre-existing cracks. When the sample is deformed at pressure higher than the pore collapse pressure P*, some very small dilatancy develops due to microcracking, and an increase in permeability is observed. Under triaxial loading, two modes of deformation can be highlighted. At low confining pressure (Pc < 50 MPa), the samples are brittle and shear localization occurs. For confining pressure > 50 MPa, the stress-strain curves are characterized by strain hardening and volumetric compaction. Stress drops are also observed, suggesting that compaction may be localized. The presence of compaction bands is confirmed by our microstructure analysis. In addition, the mechanical data allows us to plot the full yield surface for this porous basalt, which follows an elliptic cap as previously observed in high porosity sandstones and limestones.

Avaliação numérica e experimental da carga admissível de vigas compostas para monocarris de sistemas de elevação

Este trabalho foi realizado com o apoio, e em colaboração da empresa Flexcrane, que constrói e comercializa soluções flexíveis de pontes rolantes para cargas ligeiras. Com cargas máximas de 2 toneladas estas pontes e seus caminhos de rolamento são construídas essencialmente enformados a frio. O objetivo deste trabalho é a verificação numérica e experimental das cargas que este tipo de estrutura suporta, nas suas diferentes configurações. Numa aproximação por engenharia inversa, com a realização deste trabalho, foi possível determinar a carga admissível das vigas compostas utilizadas, assim como o seu comportamento quando em carga. Para obtenção destes resultados foram realizadas simulações computacionais recorrendo ao método de elementos finitos, utilizando para isso o software Ansys Workbench e ainda ensaios experimentais que permitiram validar os resultados obtidos numericamente e consolidar o conhecimento sobre o comportamento desta solução comercial. Por ser de construção modular, são possíveis diferentes combinações para o produto final, por esta razão foram estudados numericamente diferentes configurações possíveis, com e sem reforços. Foi realizada a validação experimental para a configuração mais usual, fazendo recurso a um dispositivo para ensaio de estruturas e componentes, pertencente ao Isep. Foi ainda utilizada a técnica extensométrica para avaliar as tensões em pontos selecionados e compara-los com os obtidos numericamente. Concluiu-se pelo ótimo desempenho dos produtos Flexcrane.

Mechanische Charakterisierung von Konstruktionskeramik im oberflächennahen Bereich

Engineering ceramics, indentation methods, crack-resistance, Rayleigh waves, acoustic microscopy, machining parameters, green ceramic bodies, ultrasonic contact impedance, acoustic impedance, residual stress

Tumor necrosis-like weak inducer of apoptosis as a proinflammatory cytokine in human adipocyte cells: up-regulation in severe obesity is mediated by inflammation but not hypoxia.

CONTEXT Adipose tissue hypoxia and endoplasmic reticulum (ER) stress may link the presence of chronic inflammation and macrophage infiltration in severely obese subjects. We previously reported the up-regulation of TNF-like weak inducer of apoptosis (TWEAK)/fibroblast growth factor-inducible 14 (Fn14) axis in adipose tissue of severely obese type 2 diabetic subjects. OBJECTIVES The objective of the study was to examine TWEAK and Fn14 adipose tissue expression in obesity, severe obesity, and type 2 diabetes in relation to hypoxia and ER stress. DESIGN In the obesity study, 19 lean, 28 overweight, and 15 obese nondiabetic subjects were studied. In the severe obesity study, 23 severely obese and 35 control subjects were studied. In the type 2 diabetes study, 11 type 2 diabetic and 36 control subjects were studied. The expression levels of the following genes were analyzed in paired samples of sc and visceral adipose tissue: Fn14, TWEAK, VISFATIN, HYOU1, FIAF, HIF-1a, VEGF, GLUT-1, GRP78, and XBP-1. The effect of hypoxia, inflammation, and ER stress on the expression of TWEAK and Fn14 was examined in human adipocyte and macrophage cell lines. RESULTS Up-regulation of TWEAK/Fn14 and hypoxia and ER stress surrogate gene expression was observed in sc and visceral adipose tissue only in our severely obese cohort. Hypoxia modulates TWEAK or Fn14 expression in neither adipocytes nor macrophages. On the contrary, inflammation up-regulated TWEAK in macrophages and Fn14 expression in adipocytes. Moreover, TWEAK had a proinflammatory effect in adipocytes mediated by the nuclear factor-kappaB and ERK but not JNK signaling pathways. CONCLUSIONS Our data suggest that TWEAK acts as a pro-inflammatory cytokine in the adipose tissue and that inflammation, but not hypoxia, may be behind its up-regulation in severe obesity.

Iodine intakes of 100-300 μg/d do not modify thyroid function and have modest anti-inflammatory effects.

Little information is available as to whether doses of iodide similar to those recommended in clinical practice for the prevention of iodine deficiency in pregnant women affect thyroid function. The aim of the present study was to analyse whether doses of iodide can affect thyroid function in adults, and evaluate its effect on plasma markers of oxidative stress, inflammation and acute-phase proteins. A total of thirty healthy volunteers (ten men and twenty women) with normal thyroid function were randomly assigned to three groups (n 10). Each group received a daily dose of 100, 200 or 300 μg of iodide in the form of KI for 6 months. Free tetraiodothyronine (FT4) levels at day 60 of the study were higher in the groups treated with 200 and 300 μg (P = 0·01), and correlated with the increase in urinary iodine (r 0·50, P = 0·007). This correlation lost its significance after adjustment for the baseline FT4. The baseline urinary iodine and FT4 correlated positively with the baseline glutathione peroxidase. On day 60, urinary iodine correlated with C-reactive protein (r 0·461, P = 0·018), and free triiodothyronine correlated with IL-6 (r - 0·429, P = 0·025). On day 60, the changes produced in urinary iodine correlated significantly with the changes produced in α1-antitrypsin (r 0·475, P = 0·014) and ceruloplasmin (r 0·599, P = 0·001). The changes in thyroid-stimulating hormone correlated significantly with the changes in α1-antitrypsin (r - 0·521, P = 0·005) and ceruloplasmin (r - 0·459, P = 0·016). In conclusion, the administration of an iodide supplement between 100 and 300 μg/d did not modify thyroid function in a population with adequate iodine intake. The results also showed a slight anti-inflammatory and antioxidative action of iodide.

The residual efficacy of a cypermethrin pour-on formulation applied on goats on the mortality and blood intake of Triatoma infestans

Triatoma infestans is the main vector of Trypanosoma cruzi, the aetiological agent of Chagas disease in the Gran Chaco region of South America. As a frequent blood meal source for triatomine bugs, domestic goats play a key role in the eco-epidemiology of Chagas disease. The aim of this study was to evaluate the mortality and blood intake of T. infestans fed on goats that had been treated with different doses of pour-on insecticide. Third-instar nymphs were fed on goats that had been treated with 0 cc, 5 cc, 10 cc or 15 cc of a pour-on formulation of cypermethrin. The exposure of T. infestans to animals treated at different post-application intervals revealed a residual activity of the insecticide. The mortality rate in the treated groups was higher than in the control groups until 30 days post-insecticide application (p = 0.03), except in the group treated with 5 cc, in which no mortality was detected after seven days of insecticide application. Rainfall affected the triatomicide effect, reducing the time of residual activity. The cypermethrin pour-on treatment decreased the blood intake of T. infestans. Thirty days after the cypermethrin application, nymph mortality was 16% (± 13) with both doses (10 cc and 15 cc). The 15 cc dose did not result in higher insect mortality or increased persistence compared to the 10 cc dose.

Atomic diffusion induced by stress relaxation in InGaAs/GaAs epitaxial layers

The origin of the microscopic inhomogeneities in InxGa12xAs layers grown on GaAs by molecular beam epitaxy is analyzed through the optical absorption spectra near the band gap. It is seen that, for relaxed thick layers of about 2.8 mm, composition inhomogeneities are responsible for the band edge smoothing into the whole compositional range (0.05,x,0.8). On the other hand, in thin enough layers strain inhomogeneities are dominant. This evolution in line with layer thickness is due to the atomic diffusion at the surface during growth, induced by the strain inhomogeneities that arise from stress relaxation. In consequence, the strain variations present in the layer are converted into composition variations during growth. This process is energetically favorable as it diminishes elastic energy. An additional support to this hypothesis is given by a clear proportionality between the magnitude of the composition variations and the mean strain.