Impact of nitrogen seeding on confinement and power load control of a high-triangularity JET ELMy H-mode plasma with a metal wall

This paper reports the impact on confinement and power load of the high-shape 2.5 MA ELMy H-mode scenario at JET of a change from all carbon plasma-facing components to an all metal wall. In preparation to this change, systematic studies of power load reduction and impact on confinement as a result of fuelling in combination with nitrogen seeding were carried out in JET-C and are compared with their counterpart in JET with a metallic wall. An unexpected and significant change is reported on the decrease in the pedestal confinement but is partially recovered with the injection of nitrogen.

Inter-Area Power Oscillation Frequency Mode with Wind Turbine Generator in Irish Power System using PMU Data

Two case studies are presented in this paper to demonstrate the impact of different power system operation conditions on the power oscillation frequency modes in the Irish power system. A simplified 2 area equivalent of the Irish power system has been used in this paper, where area 1 represents the Republic of Ireland power system and area 2 represents the Northern Ireland power system.

The potential power oscillation frequency modes on the interconnector during different operation conditions have been analysed in this paper. The main objective of this paper is to analyse the influence of different operation conditions involving wind turbine generator (WTG) penetration on power oscillation frequency modes using phasor measurement unit (PMU) data.

Fast Fourier transform (FFT) analysis was performed to identify the frequency oscillation mode while correlation coefficient analysis was used to determine the source of the frequency oscillation. The results show that WTG, particularly fixed speed induction generation (FSIG), gives significant contribution to inter-area power oscillation frequency modes during high WTG operation.

FAST MODE SURFACE-PLASMON DAMPING ON TUNNEL JUNCTION STRUCTURES

Using a prism-air gap-sample (Otto) configuration we have optically excited surface plasmon polaritons at the Ag-air interface of passive Al-Al oxide-Ag tunnel junction structures at wavelength 632.8 nm. It is found that the internal damping of this excitation is more than a factor of 2 greater for samples with a very thin (approximately 15 nm) Ag electrode than for samples with a thicker (approximately 40 nm) Ag electrode. This observation is explained by the fact that the fields of the surface plasmon polariton penetrate more substantially into the lossy Al base electrode when the Ag top electrode is very thin.

Wave Damping Observed in Upwardly Propagating Sausage-Mode Oscillations Contained within a Magnetic Pore

We present observational evidence of compressible MHD wave modes propagating from the solar photosphere through to the base of the transition region in a solar magnetic pore. High cadence images were obtained simultaneously across four wavelength bands using the Dunn Solar Telescope. Employing Fourier and wavelet techniques, sausage-mode oscillations displaying significant power were detected in both intensity and area fluctuations. The intensity and area fluctuations exhibit a range of periods from 181 to 412 s, with an average period∼290 s, consistent with the global p-mode spectrum. Intensity and area oscillations present in adjacent band passes were found to be out of phase with one another, displaying phase angles of 6.°12, 5.°82,and 15.°97 between the 4170 Å continuum–G-band,G-band–Na i D1, and Na i D1–Ca ii K heights, respectively, reiterating the presence of upwardly propagating sausage-mode waves. A phase relationship of ∼0° between same-bandpass emission and area perturbations of the pore best categorizes the waves as belonging to the “slow” regime of a dispersion diagram. Theoretical calculations reveal that the waves are surface modes, with initial photospheric energies in excess of 35,000 Wm‑2. The wave energetics indicate a substantial decrease in energy with atmospheric height, confirming that magnetic pores are able to transport waves that exhibit appreciable energy damping, which may release considerable energy into the local chromospheric plasma.

Identification of Small Signal Oscillation Mode Parameters from Simulated and Actual PMU Ringdown Data

This paper presents the practical use of Prony Analysis to identify small signal oscillation mode parameters from simulated and actual phasor measurement unit (PMU) ringdown data. A well-known two-area four-machine power system was considered as a study case while the latest PMU ringdown data were collected from a double circuit 275 kV main interconnector on the Irish power system. The eigenvalue analysis and power spectral density were also conducted for the purpose of comparison. The capability of Prony Analysis to identify the mode parameters from three different types of simulated PMU ringdown data has been shown successfully. Furthermore, the results indicate that the Irish power system has dominant frequency modes at different frequencies. However, each mode has good system damping.

‘At First I Saw It as a Toy’: Life Stories, Social Consciousness and Music Ethnography

This article examines the role of life narratives as discursive spaces for the performance of individual resistance. Through the inspection of three interviews with professional musicians in Athens, the essay will illustrate how the recounting of nodal events in their lives and careers facilitates an assertion of their current social ideology and their disillusionment with the popular music industry in which they operate. Ultimately, what follows will suggest a mode of listening to individual utterances and narratives as discursive forms of resistance that need to be appreciated as social acts as opposed to mere ethnographic data.

Mode of prostate cancer detection is associated with the psychological wellbeing of survivors: results from the PiCTure study

Purpose: Many men with prostate cancer are asymptomatic, diagnosed following prostate specific antigen (PSA) testing. We investigate whether mode of detection, i.e. ‘PSA detected’ or ‘clinically detected’, was associated with psychological wellbeing among prostate cancer survivors. Methods: A cross-sectional postal questionnaire was administered in 2012 to 6559 prostate cancer (ICD10 C61) survivors up to 18 years post-diagnosis, identified through population-based cancer registries in Ireland. Psychological wellbeing was assessed using the Depression Anxiety Stress Scale-21. Logistic regression was used to investigate associations between mode of detection and depression, anxiety and stress, adjusting for socio-demographic and clinical confounders. Results: The response rate was 54 % (3348/6262). Fifty-nine percent of survivors were diagnosed with asymptomatic PSA-tested disease. Prevalence of depression (13.8 vs 20.7 %; p < 0.001), anxiety (13.6 vs 20.9 %; p < 0.001) and stress (8.7 vs 13.8 %; p < 0.001) were significantly lower among survivors diagnosed with PSA-detected, than clinically detected disease. After adjusting for clinical and socio-demographic factors, survivors with clinically detected disease had significantly higher risk of depression (odds ratio (OR) = 1.46 95 % CI 1.18, 1.80; p = 0.001), anxiety (OR = 1.36 95 % CI 1.09, 1.68; p = 0.006) and stress (OR = 1.43 95 % CI 1.11, 1.85; p = 0.006) than survivors with PSA-detected disease. Conclusions: These findings contribute to the ongoing debate on benefits and risks of PSA testing and may be considered by policy makers formulating population-based prostate cancer screening policies. The relatively high prevalence of negative psychological states among survivors means that a ‘risk-adapted approach’ should be implemented to screen survivors most at risk of psychological morbidity for psychological health, and mode of detection could be considered as a risk stratum.

Evaluation of an improved atomic data basis for carbon in UEDGE emission modeling for L-mode plasmas in DIII-D

New scaled carbon atomic electron-impact excitation data is utilized to evaluate comparisons between experimental measurements and fluid emission modeling of detached plasmas at DIII-D. The C I and C II modeled emission lines for 909.8 and 514.7 nm were overestimated by a factor of 10-20 than observed experimentally for the inner leg, while the outer leg was within a factor of 2. Due to higher modeled emissions, a previous study using the UEDGE code predicted that a higher amount of carbon was required to achieve a detached outboard divertor plasma in L-mode at DIII-D. The line emission predicted by using the new scaled carbon data yields closer results when compared against experiment. We also compare modeling and measurements of Dα emission from neutral deuterium against predictions from newly calculated R-Matrix with pseudostates data available at the ADAS database. © 2013 Published by Elsevier B.V.

Nonlinear behavioral modeling of mixed signal RF-digital I/O devices

Esta tese investiga a caracterização (e modelação) de dispositivos que realizam o interface entre os domínios digital e analógico, tal como os buffers de saída dos circuitos integrados (CI). Os terminais sem fios da atualidade estão a ser desenvolvidos tendo em vista o conceito de rádio-definido-por-software introduzido por Mitola. Idealmente esta arquitetura tira partido de poderosos processadores e estende a operação dos blocos digitais o mais próximo possível da antena. Neste sentido, não é de estranhar que haja uma crescente preocupação, no seio da comunidade científica, relativamente à caracterização dos blocos que fazem o interface entre os domínios analógico e digital, sendo os conversores digital-analógico e analógico-digital dois bons exemplos destes circuitos. Dentro dos circuitos digitais de alta velocidade, tais como as memórias Flash, um papel semelhante é desempenhado pelos buffers de saída. Estes realizam o interface entre o domínio digital (núcleo lógico) e o domínio analógico (encapsulamento dos CI e parasitas associados às linhas de transmissão), determinando a integridade do sinal transmitido. Por forma a acelerar a análise de integridade do sinal, aquando do projeto de um CI, é fundamental ter modelos que são simultaneamente eficientes (em termos computacionais) e precisos. Tipicamente a extração/validação dos modelos para buffers de saída é feita usando dados obtidos da simulação de um modelo detalhado (ao nível do transístor) ou a partir de resultados experimentais. A última abordagem não envolve problemas de propriedade intelectual; contudo é raramente mencionada na literatura referente à caracterização de buffers de saída. Neste sentido, esta tese de Doutoramento foca-se no desenvolvimento de uma nova configuração de medição para a caracterização e modelação de buffers de saída de alta velocidade, com a natural extensão aos dispositivos amplificadores comutados RF-CMOS. Tendo por base um procedimento experimental bem definido, um modelo estado-da-arte é extraído e validado. A configuração de medição desenvolvida aborda não apenas a integridade dos sinais de saída mas também do barramento de alimentação. Por forma a determinar a sensibilidade das quantias estimadas (tensão e corrente) aos erros presentes nas diversas variáveis associadas ao procedimento experimental, uma análise de incerteza é também apresentada.

β-Lactams: chemical structure, mode of action and mechanisms of resistance

This synopsis summarizes the key chemical and bacteriological characteristics of β-lactams, penicillins, cephalosporins, carbanpenems, monobactams and others. Particular notice is given to first-generation to fifth-generation cephalosporins. This reviewalso summarizes the main resistancemechanism to antibiotics, focusing particular attention to those conferring resistance to broad-spectrum cephalosporins by means of production of emerging cephalosporinases (extended-spectrum β-lactamases and AmpC β-lactamases), target alteration (penicillin-binding proteins from methicillin-resistant Staphylococcus aureus) and membrane transporters that pump β-lactams out of the bacterial cell.

Global-EDF scheduling of multimode real- time systems considering mode independent tasks

Embedded real-time systems often have to support the embedding system in very different and changing application scenarios. An aircraft taxiing, taking off and in cruise flight is one example. The different application scenarios are reflected in the software structure with a changing task set and thus different operational modes. At the same time there is a strong push for integrating previously isolated functionalities in single-chip multicore processors. On such multicores the behavior of the system during a mode change, when the systems transitions from one mode to another, is complex but crucial to get right. In the past we have investigated mode change in multiprocessor systems where a mode change requires a complete change of task set. Now, we present the first analysis which considers mode changes in multicore systems, which use global EDF to schedule a set of mode independent (MI) and mode specific (MS) tasks. In such systems, only the set of MS tasks has to be replaced during mode changes, without jeopardizing the schedulability of the MI tasks. Of prime concern is that the mode change is safe and efficient: i.e. the mode change needs to be performed in a predefined time window and no deadlines may be missed as a function of the mode change.

Reactivity of bulky tris(Phenylpyrazolyl) methanesulfonate copper(I) complexes towards small unsaturated molecules

Reaction of the tris(3-phenylpyrazolyl)methane sulfonate species (Tpms(Ph))Li with the copper(I) complex [Cu(MeCN)(4)][PF6] affords [Cu(Tpms(Ph))(MeCN)] 1. The latter, upon reaction with equimolar amounts of cyclohexyl-(CyNC) or 2,6-dimethylphenyl (XylNC) isocyanides, or excess CO, furnishes the corresponding Cu(I)complexes [Cu(Tpms(Ph))(CNR)] (R = Cy 2, Xyl 3) or [Cu(Tpms(Ph))(CO)] 4. The ligated isocyanide in 2 or 3 (or the acetonitrile ligand in 1)is displaced by 3-iminoisoindolin-1-one to afford 5, the first copper(I) complex containing an 3-iminoisoindolin-1-one ligand. The ligated acetonitrile in 1 undergoes nucleophilic attack by methylamine to give the amidine complex [Cu(Tpms(Ph)){MeC(NH)NHMe}] 6, whereas only the starting materials were recovered from the attempted corresponding reactions of 2 and 3 with methylamine. Complexes 1 or 6 form the trinuclear hydroxo-copper(II)species [(mu-Cu){Cu(mu-OH) (2)(Tpms(Ph))}(2)] 7 upon air oxidation in moist methanol. In all the complexes the scorpionate ligand facially caps the metal in the N,N,O-coordination mode.

L’écologie industrielle : nouveau paradigme ou slogan à la mode

article

L'expérience comme mode de détermination des faits dans le procès civil

L'utilisation de l'expérience comme un mode de détermination des faits, c'est-à-dire comme un élément qui comble les lacunes dans l'ensemble des éléments de preuve dans le procès civil, est un thème quelque peu tabou. La doctrine est souvent basée sur la prémisse voulant que le décideur rende une décision uniquement en vertu des éléments de preuve et qu'il doit absolument s'abstenir d'insérer aux constatations quoi que ce soit qui n'est pas présent dans les éléments de preuve. Cette vision est éloignée de la réalité juridique. Dans la première partie, nous allons aborder les principes procéduraux qui empêchent l'utilisation de l'expérience comme mode de détermination des faits. Ce sont le principe de la reconstruction de l'événement du passé, le principe de l'abstraction des connaissances acquises hors du procès et le principe de l'exclusion de la preuve par ouï-dire. Ensuite, nous portons notre attention sur les différents types d'expérience, c'est-à-dire l'expérience profane, divisible en bon sens et sens commun, et l'expérience scientifique, ainsi sur leurs modes de fonctionnement dans le procès civil. La première partie se termine par une brève confrontation des différents types d'expérience avec les principes procéduraux. La deuxième partie est consacré à l'analyse de l'expérience dans trois instruments juridiques: la connaissance d'office, la présomption de fait et le témoignage d'expert. Nous nous intéressons principalement à vérifier si l'expérience fonctionne à l'intérieur de ces instruments juridiques comme mode de détermination des faits et ensuite quelles sont les limites que le droit pose à l'expérience dans ce rôle. L'analyse va confirmer que le principal instrument par lequel l'expérience comme mode de détermination des faits pénètre dans le procès civil est la présomption de fait.

Identification des peptides du complexe majeur d’histocompatibilité de classe I par spectrométrie de masse

L’immunité adaptive et la discrimination entre le soi et le non-soi chez les vertébrés à mâchoire reposent sur la présentation de peptides par les récepteurs d’histocompatibilité majeur de classe I. Les peptides antigéniques, présentés par les molécules du complexe d’histocompatibilité (CMH), sont scrutés par les lymphocytes T CD8 pour une réponse immunitaire appropriée. Le répertoire des peptides du CMH de classe I, aussi appelé immunopeptidome, est généré par la dégradation protéosomale des protéines endogènes, et a un rôle essentiel dans la régulation de l’immunité cellulaire. La composition de l’immunopeptidome dépend du type de cellule et peut présenter des caractéristiques liées à des maladies comme le cancer. Les peptides antigéniques peuvent être utilisés à des fins immunothérapeutiques notamment dans le traitement voire la prévention de certains cancers. La spectrométrie de masse est un outil de choix pour l’identification, le séquençage et la caractérisation de ces peptides. Cependant, la composition en acides aminés, la faible abondance et la diversité de ces peptides compliquent leur détection et leur séquençage. Nous avons développé un programme appelé StatPeaks qui permet de calculer un certains nombres de statistiques relatives à la fragmentation des peptides. À l’aide de ce programme, nous montrons sans équivoque que les peptides du CMH classe I, en mode de fragmentation par dissociation induite par collision (CID), fragmentent très différemment des peptides trypsiques communément utilisés en protéomique. Néanmoins, la fragmentation par décomposition induite par collision à plus haute énergie (HCD) proposée par le spectromètre LTQ-Orbitrap Velos améliore la fragmentation et fournit une haute résolution qui permet d’obtenir une meilleure confiance dans l’identification des peptides du CMH de classe I. Cet avantage permet d’effectuer le séquençage de novo pour identifier les variants polymorphes qui ne sont normalement pas identifiés par les recherches utilisant des bases de données. La comparaison des programmes de séquençage Lutefisk, pepNovo, pNovo, Vonode et Peaks met en évidence que le dernier permet d’identifier un plus grand nombre de peptides du CMH de classe I. Ce programme est intégré dans une chaîne de traitement de recherche d’antigènes mineurs d’histocompatibilité. Enfin, une base de données contenant les informations spectrales de plusieurs centaines de peptides du CMH de classe I accessible par Internet a été développée.