Ni catalyst on mixed support of CeO2-ZrO2 and Al2O3: Effect of composition of CeO2-ZrO2 solid solution on the methane steam reforming reaction

In this study, catalysts containing 5 wt.% Ni deposited on a support composed of a CeO2-ZrO2 solid solution deposited on alumina were tested in the steam reforming of methane. The supports, with various ratios of Ce to Zr, were prepared by co-precipitation of the oxide precursors, followed by calcination in synthetic air. The catalysts were then prepared by Ni impregnation of the supports. The prepared solids were characterized by temperature-programmed reduction with H-2 (TPR-H-2), in situ X-ray diffraction (XRD) and X-ray absorption near-edge structure (XANES) spectroscopy. The XRD analysis confirmed the formation of a solid solution between ZrO2 and CeO2. In the catalytic tests, it was found that catalysts with higher Ce content did not exhibit deactivation during 6 h of reaction. The catalyst with highest Ce content, Ni(0.8Ce0.2Zr)AI, provided the best result, with the highest rate of conversion of methane and the lowest carbon deposition, which may be partly due to the smaller Ni-0 crystallites in this sample and also the segregated CeO2 particles may have favored H2O adsorption which could lead to higher C gasification. (C) 2012 Elsevier B.V. All rights reserved.

Hydrogen and Methane Production, Energy Recovery, and Organic Matter Removal from Effluents in a Two-Stage Fermentative Process

This study evaluates the potential for using different effluents for simultaneous H-2 and CH4 production in a two-stage batch fermentation process with mixed microflora. An appreciable amount of H-2 was produced from parboiled rice wastewater (23.9 mL g(-1) chemical oxygen demand [COD]) and vinasse (20.8 mL g(-1) COD), while other effluents supported CH4 generation. The amount of CH4 produced was minimum for sewage (46.3 mL g(-1) COD), followed by parboiled rice wastewater (115.5 mL g(-1) COD) and glycerol (180.1 mL g(-1) COD). The maximum amount of CH4 was observed for vinasse (255.4 mL g(-1) COD). The total energy recovery from vinasse (10.4 kJ g(-1) COD) corresponded to the maximum COD reduction (74.7 %), followed by glycerol (70.38 %, 7.20 kJ g(-1) COD), parboiled rice wastewater (63.91 %, 4.92 kJ g(-1) COD), and sewage (51.11 %, 1.85 kJ g(-1) COD). The relatively high performance of vinasse in such comparisons could be attributed to the elevated concentrations of macronutrients contained in raw vinasse. The observations are based on kinetic parameters of H-2 and CH4 production and global energy recovery of the process. These observations collectively suggest that organic-rich effluents can be deployed for energy recovery with sequential generation of H-2 and CH4.

Oxidation and pyrolysis of methane and methyl formate in a plug flow reactor: computational and experimenal studies

Biodiesel represents a possible substitute to the fossil fuels; for this reason a good comprehension of the kinetics involved is important. Due to the complexity of the biodiesel mixture a common practice is the use of surrogate molecules to study its reactivity. In this work are presented the experimental and computational results obtained for the oxidation and pyrolysis of methane and methyl formate conducted in a plug flow reactor. The work was divided into two parts: the first one was the setup assembly whilst, in the second one, was realized a comparison between the experimental and model results; these last was obtained using models available in literature. It was started studying the methane since, a validate model was available, in this way was possible to verify the reliability of the experimental results. After this first study the attention was focused on the methyl formate investigation. All the analysis were conducted at different temperatures, pressures and, for the oxidation, at different equivalence ratios. The results shown that, a good comprehension of the kinetics is reach but efforts are necessary to better evaluate kinetics parameters such as activation energy. The results even point out that the realized setup is adapt to study the oxidation and pyrolysis and, for this reason, it will be employed to study a longer chain esters with the aim to better understand the kinetic of the molecules that are part of the biodiesel mixture.

Experimental and computational study of methane and methyl formate pyrolysis and oxidation in a flow reactor

A study of the pyrolysis and oxidation (phi 0.5-1-2) of methane and methyl formate (phi 0.5) in a laboratory flow reactor (Length = 50 cm, inner diameter = 2.5 cm) has been carried out at 1-4 atm and 300-1300 K temperature range. Exhaust gaseous species analysis was realized using a gas chromatographic system, Varian CP-4900 PRO Mirco-GC, with a TCD detector and using helium as carrier for a Molecular Sieve 5Å column and nitrogen for a COX column, whose temperatures and pressures were respectively of 65°C and 150kPa. Model simulations using NTUA [1], Fisher et al. [12], Grana [13] and Dooley [14] kinetic mechanisms have been performed with CHEMKIN. The work provides a basis for further development and optimization of existing detailed chemical kinetic schemes.

Alpha, Omega end group functionalization of RAFT polymers based on pentafluorophenyl esters and methane thiosulfonates

While polymers with different functional groups along the backbone have intensively been investigated, there is still a challenge in orthogonal functionalization of the end groups. Such well-defined systems are interesting for the preparation of multiblock (co) polymers or polymer networks, for bio-conjugation or as model systems for examining the end group separation of isolated polymer chains. rnHere, Reversible Addition Fragmentation Chain Transfer (RAFT) polymerization was employed as method to investigate improved techniques for an a, w end group functionalization. RAFT produces polymers terminated in an R group and a dithioester-Z group, where R and Z stem from a suitable chain transfer agent (CTA). rnFor alpha end group functionalization, a CTA with an activated pentafluorophenyl (PFP) ester R group was designed and used for the polymerization of various methacrylate monomers, N-isopropylacrylamide and styrene yielding polymers with a PFP ester as a end group. This allowed the introduction of inert propyl amides, of light responsive diazo compounds, of the dyes NBD, Texas Red, or Oregon Green, of the hormone thyroxin and allowed the formation of multiblocks or peptide conjugates. rnFor w end group functionalization, problems of other techniques were overcome through an aminolysis of the dithioester in the presence of a functional methane thiosulfonate (MTS), yielding functional disulfides. These disulfides were stable under ambient conditions and could be cleaved on demand. Using MTS chemistry, terminal methyl disulfides (enabling self-assembly on planar gold surfaces and ligand substitution on gold and semiconductor nanoparticles), butynyl disulfide end groups (allowing the “clicking” of the polymers onto azide functionalized surfaces and the selective removal through reduction), the bio-target biotin, and the fluorescent dye Texas Red were introduced into polymers. rnThe alpha PFP amidation could be performed under mild conditions, without substantial loss of DTE. This way, a step-wise synthesis produced polymers with two functional end groups in very high yields. rnAs examples, polymers with an anchor group for both gold nanoparticles (AuNP) and CdSe / ZnS semi-conductor nanoparticles (QD) and with a fluorescent dye end group were synthesized. They allowed a NP decoration and enabled an energy transfer from QD to dye or from dye to AuNP. Water-soluble polymers were prepared with two different bio-target end groups, each capable of selectively recognizing and binding a certain protein. The immobilization of protein-polymer-protein layers on planar gold surfaces was monitored by surface plasmon resonance.Introducing two different fluorescent dye end groups enabled an energy transfer between the end groups of isolated polymer chains and created the possibility to monitor the behavior of single polymer chains during a chain collapse. rnThe versatility of the synthetic technique is very promising for applications beyond this work.

Methane production through anaerobic digestion of dedicated energy crops

Methane yield of ligno-cellulosic substrates (i.e. dedicated energy crops and agricultural residues) may be limited by their composition and structural features. Hence, biomass pre-treatments are envisaged to overcome this constraint. This thesis aimed at: i) assessing biomass and methane yield of dedicated energy crops; ii) evaluating the effects of hydrothermal pre-treatments on methane yield of Arundo; iii) investigating the effects of NaOH pre-treatments and iv) acid pre-treatments on chemical composition, physical structure and methane yield of two dedicated energy crops and one agricultural residue. Three multi-annual species (Arundo, Switchgrass and Sorghum Silk), three sorghum hybrids (Trudan Headless, B133 and S506) and a maize, as reference for AD, were studied in the frame of point i). Results exhibit the remarkable variation in biomass yield, chemical characteristics and potential methane yield. The six species alternative to maize deserve attention in view of a low need of external inputs but necessitate improvements in biodegradability. In the frame of point ii), Arundo was subjected to hydrothermal pre-treatments at different temperature, time and acid catalyst (with and without H2SO4). Pre-treatments determined a variable effect on methane yield: pre-treatments without acid catalyst achieved up to +23% CH4 output, while pre-treatments with H2SO4 catalyst incurred a methanogenic inhibition. Two biomass crops (Arundo and B133) and an agricultural residue (Barley straw) were subject to NaOH and acid pre-treatments, in the frame of point iii) and iv), respectively. Different pre-treatments determined a change of chemical and physical structure and an increase of methane yield: up to +30% and up to +62% CH4 output in Arundo with NaOH and acid pre-treatments, respectively. It is thereby demonstrated that pre-treatments can actually enhance biodegradability and subsequent CH4 output of ligno-cellulosic substrates, although pre-treatment viability needs to be evaluated at the level of full scale biogas plants in a perspective of profitable implementation.

Sources and pathways of methane formed in oxidative environments

Methane is the most abundant reduced organic compound in the atmosphere. As the strongest known long-lived greenhouse gas after water vapour and carbon dioxide methane perturbs the radiation balance of Earth’s atmosphere. The abiotic formation of methane requires ultraviolet irradiation of organic matter or takes place in locations with high temperature and/or pressure, e.g. during biomass burning or serpentinisation of olivine, under hydrothermal conditions in the oceans deep or below tectonic plates. The biotic methane formation was traditionally thought to be formed only by methanogens under strictly anaerobic conditions, such as in wetland soils, rice paddies and agricultural waste. rnIn this dissertation several chemical pathways are described which lead to the formation of methane under aerobic and ambient conditions. Organic precursor compounds such as ascorbic acid and methionine were shown to release methane in a chemical system including ferrihydrite and hydrogen peroxide in aquatic solution. Moreover, it was shown by using stable carbon isotope labelling experiments that the thio-methyl group of methionine was the carbon precursor for the methane produced. Methionine, a compound that plays an important role in transmethylation processes in plants was also applied to living plants. Stable carbon isotope labelling experiments clearly verified that methionine acts as a precursor compound for the methane from plants. Further experiments in which the electron transport chain was inhibited suggest that the methane generation is located in the mitochondria of the plants. The abiotic formation of methane was shown for several soil samples. Important environmental parameter such as temperature, UV irradiation and moisture were identified to control methane formation. The organic content of the sample as well as water and hydrogen peroxide might also play a major role in the formation of methane from soils. Based on these results a novel scheme was developed that includes both biotic and chemical sources of methane in the pedosphere.rn

Development and application of an analytical method for the determination of total atmospheric biogenic non-methane organic carbon

Ein wesentlicher Anteil an organischem Kohlenstoff, der in der Atmosphäre vorhanden ist, wird als leichtflüchtige organische Verbindungen gefunden. Diese werden überwiegend durch die Biosphäre freigesetzt. Solche biogenen Emissionen haben einen großen Einfluss auf die chemischen und physikalischen Eigenschaften der Atmosphäre, indem sie zur Bildung von bodennahem Ozon und sekundären organischen Aerosolen beitragen. Um die Bildung von bodennahem Ozon und von sekundären organischen Aerosolen besser zu verstehen, ist die technische Fähigkeit zur genauen Messung der Summe dieser flüchtigen organischen Substanzen notwendig. Häufig verwendete Methoden sind nur auf den Nachweis von spezifischen Nicht-Methan-Kohlenwasserstoffverbindungen fokussiert. Die Summe dieser Einzelverbindungen könnte gegebenenfalls aber nur eine Untergrenze an atmosphärischen organischen Kohlenstoffkonzentrationen darstellen, da die verfügbaren Methoden nicht in der Lage sind, alle organischen Verbindungen in der Atmosphäre zu analysieren. Einige Studien sind bekannt, die sich mit der Gesamtkohlenstoffbestimmung von Nicht-Methan-Kohlenwasserstoffverbindung in Luft beschäftigt haben, aber Messungen des gesamten organischen Nicht-Methan-Verbindungsaustauschs zwischen Vegetation und Atmosphäre fehlen. Daher untersuchten wir die Gesamtkohlenstoffbestimmung organische Nicht-Methan-Verbindungen aus biogenen Quellen. Die Bestimmung des organischen Gesamtkohlenstoffs wurde durch Sammeln und Anreichern dieser Verbindungen auf einem festen Adsorptionsmaterial realisiert. Dieser erste Schritt war notwendig, um die stabilen Gase CO, CO2 und CH4 von der organischen Kohlenstofffraktion zu trennen. Die organischen Verbindungen wurden thermisch desorbiert und zu CO2 oxidiert. Das aus der Oxidation entstandene CO2 wurde auf einer weiteren Anreicherungseinheit gesammelt und durch thermische Desorption und anschließende Detektion mit einem Infrarot-Gasanalysator analysiert. Als große Schwierigkeiten identifizierten wir (i) die Abtrennung von CO2 aus der Umgebungsluft von der organischen Kohlenstoffverbindungsfaktion während der Anreicherung sowie (ii) die Widerfindungsraten der verschiedenen Nicht-Methan-Kohlenwasserstoff-verbindungen vom Adsorptionsmaterial, (iii) die Wahl des Katalysators sowie (iiii) auftretende Interferenzen am Detektor des Gesamtkohlenstoffanalysators. Die Wahl eines Pt-Rd Drahts als Katalysator führte zu einem bedeutenden Fortschritt in Bezug auf die korrekte Ermittlung des CO2-Hintergrund-Signals. Dies war notwendig, da CO2 auch in geringen Mengen auf der Adsorptionseinheit während der Anreicherung der leichtflüchtigen organischen Substanzen gesammelt wurde. Katalytische Materialien mit hohen Oberflächen stellten sich als unbrauchbar für diese Anwendung heraus, weil trotz hoher Temperaturen eine CO2-Aufnahme und eine spätere Abgabe durch das Katalysatormaterial beobachtet werden konnte. Die Methode wurde mit verschiedenen leichtflüchtigen organischen Einzelsubstanzen sowie in zwei Pflanzenkammer-Experimenten mit einer Auswahl an VOC-Spezies getestet, die von unterschiedlichen Pflanzen emittiert wurden. Die Pflanzenkammer-messungen wurden durch GC-MS und PTR-MS Messungen begleitet. Außerdem wurden Kalibrationstests mit verschiedenen Einzelsubstanzen aus Permeations-/Diffusionsquellen durchgeführt. Der Gesamtkohlenstoffanalysator konnte den tageszeitlichen Verlauf der Pflanzenemissionen bestätigen. Allerdings konnten Abweichungen für die Mischungsverhältnisse des organischen Gesamtkohlenstoffs von bis zu 50% im Vergleich zu den begleitenden Standardmethoden beobachtet werden.

Einzelpartikel- und Ensemblemessungen mit dem Aerosolmassenspektrometer (AMS): Untersuchungen zu Quellen und chemischer Prozessierung von Aerosolpartikeln im Submikrometerbereich

Atmosphärische Aerosolpartikel haben einen Einfluss sowohl auf das Klima als auch auf die menschliche Gesundheit, wobei sowohl die Größe, als auch die chemische Zusammensetzung der Partikel maßgeblich sind. Um insbesondere die chemische Zusammensetzung der Partikel in Abhängigkeit ihrer Quellen besser zu verstehen, wurden im Rahmen dieser Arbeit massenspektrometrische Untersuchungen thermisch verdampfbarer Partikel im Submikrometerbereich durchgeführt. Hierzu wurden sowohl die Massenspektren einzelner Partikel, als auch die von Ensembles von Partikeln mit dem Aerodyne Aerosolmassenspektrometer (AMS) in mehreren Feldmesskampagnen untersucht. Für die Messung von Einzelpartikelmassenspektren wurde das AMS zunächst durch den Einbau eines optischen Partikeldetektors (light scattering probe) modifiziert und anschließend eingehend charakterisiert. Dabei wurde festgestellt, dass mit dem Gerät im Partikelgrößenbereich von etwa 400-750 nm (untere Grenze bedingt durch die Detektionseffizienz des optischen Detektors, obere Grenze durch die Transmissionseffizienz des Aerosoleinlasssystems) quantitative Einzelpartikelmessungen möglich sind. Zudem wurde die Analyse der erhaltenen Messdaten systematisiert, und durch Einsatz von Standardspektren ein Sortieralgorithmus für die Einzelpartikelmassenspektren entwickelt, der erfolgreich auf Daten von Feldmesskampagnen angewandt werden konnte. Mit diesem Sortieralgorithmus sind zudem quantitative Aussagen über die verschiedenen Partikelbestandteile möglich. Im Sommer 2009 und im Winter 2010 fanden im Großraum Paris zwei einmonatige Feldmesskampagnen statt, bei denen unter anderem der Einfluss der Abluftfahne der Megastadt auf seine Vororte untersucht wurde. Erhöhte Konzentrationen sekundär gebildeter Aerosolkomponenten (Nitrat, Sulfat, oxidiertes organisches Aerosol (OOA)) waren insbesondere beim Herantransport kontinentaler Luftmassen zu beobachten. Im Gegensatz dazu waren die beobachteten Konzentrationen der Tracer primärer Emissionen NOx, BC (black carbon) und HOA (hydrocarbonlike organic aerosol) neben der lokalen Quellstärke insbesondere durch die herrschende Windgeschwindigkeit beeinflusst. Aus dem Vergleich der Messungen an drei Stationen konnte der Einfluss der Megastadt Paris auf seine Vororte (unter Annahme gleicher lokaler Emissionen an den zwei Vorort-Stationen) zu 0,1-0,7 µg m-3 BC, 0,3-1,1 µg m-3 HOA, und 3-5 ppb NOx abgeschätzt werden. Zudem konnten für zwei Stationen aus den Ensemble- bzw. den Einzelpartikelmessungen unabhängig voneinander zwei verschiedene HOA-Typen unterschieden werden, die den Quellen „Kochen“ und „Autoabgase“ zugeordnet wurden. Der Anteil der Partikel aus den Quellen „Kochen“ bzw. „Autoabgase“ am Gesamt-HOA betrug 65,5 % und 34,5 % für die Ensemblemessungen in der Innenstadt (nahe vieler Restaurants), und für die Einzelpartikelmessungen in einem Vorort 59 % bzw. 41 % (bezogen auf die Partikelanzahl, welche hier der Masse etwa proportional ist). Die Analyse der Einzelpartikelmassenspektren erbrachte zudem neue Erkenntnisse über den Mischungszustand der Einzelpartikel. So konnte belegt werden, dass Nitrat, Sulfat und OOA intern gemischt sind, HOA-Partikel aber als externe Mischung mit diesen vorliegen. Zudem konnte anhand der Tagesgänge der Masse pro Partikel von OOA, Nitrat und Sulfat und der Anzahl der diese Substanzen enthaltenden Partikel gezeigt werden, dass der im Ensemblemodus beobachtete fehlende Tagesgang der Sulfat-Massenkonzentration wahrscheinlich durch die gegensätzlichen Effekte der Modulation der Partikelanzahlkonzentration durch die sich verändernde Mischungsschichthöhe und der variierenden Masse an Sulfat pro Partikel (mittägliche photochemische Neuproduktion und Kondensation auf existierende Partikel) erklärt werden kann. Für OOA ist eine ähnliche Erklärung des Ensemblemodus-Tagesganges jedoch nur teilweise möglich; weitere Arbeit ist daher nötig, um auch für diese Substanzklasse belastbare Aussagen aus dem Vergleich der Ensemble- und Einzelpartikelmessungen zu erhalten. Im Rahmen einer Labormesskampagne an der AIDA-Kammer in Karlsruhe wurden Ensemble- und Einzelpartikelmassenspektren von Bakterien aufgenommen. Es konnte gezeigt werden, dass es prinzipiell möglich ist, Bakterien in Außenluft mittels Einzelpartikelmessungen nachzuweisen, jedoch wahrscheinlich nur bei sehr hohen Anzahlkonzentrationen. Der Nachweis von Bakterien und anderen primären biologischen Aerosolpartikeln mit dem AMS sollte daher in weiterführenden Experimenten noch optimiert werden.

Abiotic methane formation in oxic soils

Methane plays an important role as a radiatively and chemically active gas in our atmosphere. Until recently, sources of atmospheric methane in the biosphere have been attributed to strictly anaerobic microbial processes during degradation of organic matter. However, some potentially abiotic sources from the biosphere have been discovered in the past few years, starting with methane emissions from plants and plant litter up to the recent discovery of methane production in saprotrophic fungi.rnAlso methane fluxes from aerobic soils have been observed for decades but no alternative source to methanogenesis has been identified so far.rnThis work aims to provide evidence for non-microbial methane formation in soils under oxic conditions. It was found that soils release methane upon heating and other environmental factors like ultraviolet irradiation, and drying-rewetting cycles. The chemical formation of methane during degradation of soil organic matter represents an additional source in soil that helps to understand the methane cycle in aerobic soils. Although the emission fluxes are relatively low when compared to those from aerobic soil sources like wetlands, they may still be important in warm and wet regions subjected to ultraviolet radiation. Therefore this methane source might be highly sensitive to global climate change.rn

Carbon sequestration in Himalaya's alpine meadows: Mitigating cropping encroachment on pastures in Northern Pakistan

Rangelands store about 30% of the world’s carbon and support over 120 million pastoralists globally. Adjusting the management of remote alpine pastures bears a substantial climate change mitigation potential that can provide livelihood support for marginalized pastoralists through carbon payment. Landless pastoralists in Northern Pakistan seek higher income by cropping potatoes and peas over alpine pastures. However, tilling steep slopes without terracing exposes soil to erosion. Moreover, yields decline rapidly requiring increasing fertilizer inputs. Under these conditions, carbon payment could be a feasible option to compensate pastoralists for renouncing hazardous cropping while favoring pastoral activities. The study quantifies and compares C on cropped and grazed land. The hypothesis was that cropping on alpine pastures reduces former carbon storage. The study area located in the Naran valley of the Pakistani Himalayas receives an annual average of 819 mm of rain and 764 mm of snow. Average temperatures remain below 0°C from November to March while frost may occur all year round. A total of 72 soil core samples were collected discriminating land use (cropping, pasture), aspect (North, South), elevation (low 3000, middle 3100, and high 3200 m a.s.l.), and soil depth (shallow 0-10, deep 10-30 cm). Thirty six biomass samples were collected over the same independent variables (except for soil depth) using a 10x10x20 cm steal box inserted in the ground for each sample. Aboveground biomass and coarse roots were separated from the soil aggregate and oven-dried. Soil organic carbon (SOC) and biomass carbon (BC) were estimated through a potassium dichromate oxidation treatment. The samples were collected during the second week of October 2010 at the end of the grazing and cropping season and before the first snowfall. The data was statistically analyzed by means of a one-way analysis of variance. Results show that all variables taken separately have a significant effect on mean SOC [%]: crop/pasture 1.33/1.6, North/South 1.61/1.32, low/middle/high 1.09/1.62/1.68, shallow/deep 1.4/1.53. However, for BC, only land use has a significant effect with more than twice the amount of carbon in pastures [g m-2]: crop/pasture 127/318. These preliminary findings suggest that preventing the conversion of pastures into cropping fields in the Naran valley avoids an average loss of 12.2 t C ha-1 or 44.8 t CO2eq ha-1 representing a foreseeable compensation of 672 € ha-1 for the Naran landless pastoralists who would renounce cropping. The ongoing study shall provide a complete picture for carbon payment integrating key aspects such as the rate of cropping encroachment over pastures per year, the methane leakage from the system due to livestock enteric fermentation, the expected cropping income vs. livestock income and the transaction costs of implementing the mitigation project, certifying it, and verifying carbon credits. A net present value over an infinite time horizon for the mitigation scenario shall be estimated on an iterative simulation to consider weather and price uncertainties. The study will also provide an estimate of the minimum price of carbon at which pastoralists would consider engaging in the mitigation activity.