Desgaste corrosivo-cavitativo-erosivo de um aço-carbono em meio aquoso com frações de sal (NaCl), CO2 e particulados sólidos (SiO2)

A batch of eighty-four coupons of low carbon steel were investigated at laboratory conditions under a corrosive, cavitative-corrosive (CO2) and corrosive-erosive (SiO2 + CO2) in an aqueous salt solution and two levels of temperature. The following measurements were made on Vickers (HV0,05, HV0,10, HV0,20) Microhardness tests at three levels of subsurface layer. A turbulent flow collided on the cylindrical sample, with and without mechanical stirring and gas bubbling, with and without fluid contamination by solid particles of SiO2, at two temperatures. Surface Roughness and Waviness, under two conditions "as received, after machining" and "after worn out", as well as gravimetric and electrochemical parameter were measured on the two opposite generatrices of each cylindrical sample, on the flow upstream (0°) and downstream (180°) by Profilometry, Mass Variation and Linear Polarization Resistance (LPR). The results of the Microhardness and Surface Texture of all coupons were subjected to statistical comparison, using the software Statgraphics® Centurion XVI, 95% statistical certainty, and significant differences were observed in some arrays of measurements. The corrosive wear rate measured by LPR and mass variation shown to be sensitive to the presence of bubbles and hydrodynamic fluctuations inside the cell, considering the temperature and contamination of corrosive fluid by solid particles. The main results of visual inspection relative to some topologies of the surface damages involving different mechanisms that were seen to give explanation for some fluctuations in wear rates of the steel experimentally investigated

Análise topológica experimental por perfilometria cíclica indutiva de superficies de paredes estruturais

To enhance the maintenance practices, Oil and Gas Pipelines are inspected from the inside by automated systems called PIG (Pipeline Inspection Gauge). The inspection and mapping of defects, as dents and holes, in the internal wall of these pipelines are increasingly put into service toward an overall Structural Integrity Policy. The residual life of these structures must be determined such that minimize its probability of failure. For this reason, the investigation on the detection limits of some basic topological features constituted by peaks or valleys disposed along a smooth surface is of great value for determining the sensitivity of the measurements of defects from some combinations of circumferential, axial and radial extent. In this investigation, it was analyzed an inductive profilometric sensor to scan three races, radius r1, r2, r3, in a circular surface of low carbon steel, equipped with eight consecutive defects simulated by bulges and holes by orbit, equally spaced at p/4 rad. A test rig and a methodology for testing in laboratory were developed to evaluate the sensor response and identify their dead zones and jumps due to fluctuations as a function of topological features and scanning velocity, four speeds different. The results are presented, analyzed and suggestions are made toward a new conception of sensor topologies, more sensible to detect these type of damage morphologies

Medição e modelagem da resposta de um sensor de pig perfilométrico sob diferentes solicitações dinâmicas

Ensure the integrity of the pipeline network is an extremely important factor in the oil and gas industry. The engineering of pipelines uses sophisticated robotic inspection tools in-line known as instrumented pigs. Several relevant factors difficult the inspection of pipelines, especially in offshore field which uses pipelines with multi-diameters, radii of curvature accentuated, wall thickness of the pipe above the conventional, multi-phase flow and so on. Within this context, appeared a new instrumented Pig, called Feeler PIG, for detection and sizing of thickness loss in pipelines with internal damage. This tool was developed to overcome several limitations that other conventional instrumented pigs have during the inspection. Several factors influence the measurement errors of the pig affecting the reliability of the results. This work shows different operating conditions and provides a test rig for feeler sensors of an inspection pig under different dynamic loads. The results of measurements of the damage type of shoulder and holes in a cyclic flat surface are evaluated, as well as a mathematical model for the sensor response and their errors from the actual behavior

Estudo de um sistema híbrido de destilação solar para polimento de águas produzidas

The oil industry, experiencing a great economic and environmental impact, has increasingly invested in researches aiming a more satisfactory treatment of its largest effluent, i.e., produced water. These are mostly discarded at sea, without reuse and after a basic treatment. Such effluent contains a range of organic compounds with high toxicity and are difficult to remove, such as polycyclic aromatic hydrocarbons, salts, heavy metals, etc.. The main objective of this work was to study the solar distillation of produced water pre-treated to remove salts and other contaminants trough of a hybrid system with a pre-heater. This developed apparatus was called solar system, which consists of a solar heater and a conventional distillation solar still. The first device consisted of a water tank, a solar flat plate collector and a thermal reservoir. The solar distillator is of simple effect, with 1m2 of flat area and 20° of inclination. This dissertation was divided in five steps: measurements in the solar system, i.e. temperatures and distillate flow rate and weather data; modeling and simulation of the system; study of vapor-liquid equilibrium of the synthetic wastewater by the aqueous solution of p-xylene; physical and chemical analyses of samples of the feed, distillate and residue, as well as climatology pertinent variables of Natal-RN. The solar system was tested separately, with the supply water, aqueous NaCl and synthetic oil produced water. Temperature measurements were taken every minute of the thermal reservoir, water tank and distillator (liquid and vapor phases). Data of solar radiation and rainfall were obtained from INPE (National Institute for Space Research). The solar pre-heater demonstrated to be effective for the liquid systems tested. The reservoir fluid had an average temperature of 58°C, which enabled the feed to be pre-heated in the distillator. The temperature profile in the solar distillator showed a similar behavior to daily solar radiation, with temperatures near 70°C. The distillation had an average yield of 2.4 L /day, i.e., an efficiency of 27.2%. Mathematical modeling aided the identification of the most important variables and parameters in the solar system. The study of the vapor-liquid equilibrium from Total Organic Carbon (TOC) analysis indicated heteroazeotropia and the vapor phase resulted more concentrated in p-xylene. The physical-chemical analysis of pH, conductivity, Total Dissolved Solids (TDS), chlorides, cations (including heavy metals) and anions, the effluent distillate showed satisfactory results, which presents a potential for reuse. The climatological study indicates the region of Natal-RN as favorable to the operation of solar systems, but the use of auxiliary heating during periods of higher rainfall and cloud cover is also recommended

Influência da intensidade de aeração na formação do floco de lodo ativado e na eficiência de remoção de matéria orgânica

In wastewater treatment, activated sludge systems have been a technology widely applied as secondary treatment. During this step, which has a strong biological aspect, it is necessary to introduce oxygen supply for the maintenance of metabolic activity of the bacteria through the aerators. Aeration devices are responsible for most of the energy consumption in this stage. In this background, the influence of three aeration intensities (atmospheric air flow 3.5, 7.0 and 10.5 L.min-1) and the concentration of dissolved oxygen (DO) on the dimension of activated sludge flocs as well as on the efficiency of organic matter removal were assessed using a traditional activated sludge system which was fed with synthetic domestic wastewater. Samples were taken weekly from the three units that make up the system feed, aeration and storage tank in order to verify the Chemical Oxygen Demand (COD). It was established the process efficiency through a comparison between the initial and final COD. Besides the parameters already mentioned, this monitoring work on activated sludge batch system was also observed by Mixed Liquor Suspend Solids (MLSS), Volatile Suspend Solids (VSS), pH and temperature measures. The results have showed a maximum removal efficiency around 75% in the first aeration sequence and approximately 85% for the second and third one. For the first aeration, the DO concentration remained higher than 3.0 mg.L-1 and a diameter range from 10 to 60 μm was observed. In the second e third sequence, the DO concentration remained higher than 4.0 mg.L-1 with a diameter range of 10 until 200 μm. Although the sequence 1 and 2 have presented similar performances for organic matter removal, the sequence 2 promoted a regular floc size distribution and with lower values of Sludge Volumetric Index (SVI) meaning a better flocculating ability. In addition, the results reaffirmed what the literature has reported: higher DO concentrations produce flocs with greater dimensions

Eutrofização do Reservatório Cruzeta na bacia representativa do rio Seridó RN

Eutrophication has been listed as one of the main problems of water pollution on a global level. In the Brazilian semi-arid areas this problem takes even greater proportions due to characteristical water scarcity of the region. It is extremely important to the predictive eutrophication models development and to the reservoirs management in the semi-arid region, studies that promotes understanding of the mechanisms responsible for the expansion and control of algae blooms, essential for improving the water quality of these environments. The present study had as its main aims, evaluate the temporal pattern of trophic state, considering the influence of nutrients (N and P) and the light availability in the water column in the development of phytoplankton biomass, and perform the mathematical modelling of changes in phosphorus and chlorophyll a concentrations in the Cruzeta man-made lake located on Seridó, a typical semi-arid region of Rio Grande do Norte. To this, a fortnightly monitoring was performed in the reservoir in 05 stations over the months of March 2007 to May 2008. Were measured the concentrations of total phosphorus, total organic nitrogen, chlorophyll a, total, fixed and volatile suspended solids, as well as the measure of transparency (Secchi) and the profiles of photosynthetic active radiation (PAR), temperature, pH, dissolved oxygen and electrical conductivity in the water column. Measurements of vertical profiles have shown some periods of chemical and thermal stratification, especially in the rainy season, due to increased water column depth, however, the reservoir can be classified as warm polimitic. During the study period the reservoir was characterized as eutrophic considering the concentrations of phosphorus and most of the time as mesotrophic, based on the concentrations of chlorophyll a, according to the Thornton & Rast (1993) classification. The N:P relations suggest N limitation, conversely, significant linear relationship between the algae biomass and nutrients (N and P) were not observed in our study. However, a relevant event was the negative and significant correlation presented by Kt and chlorophyll a (r ² = 0.83) at the end of the drought of 2007 and the rainy season of 2008, and the algal biomass collapse observed at the end of the drought season (Dec/07). The equation used to simulate the change in the total phosphorus was not satisfactory, being necessary inclusion of parameters able to increase the power of the model prediction. The chlorophyll a simulation presented a good adjustment trend, however there is a need to check the calibrated model parameters and subsequent equation validation

A gestão da qualidade nos cursos de graduação a distância da UFRN/SEDIS : a percepção dos discentes

The management of water resources in the river basin level, as it defines the Law nº 9433/97, requires the effective knowledge of the processes of hydrological basin, resulting from studies based on consistent series of hydrological data that reflect the characteristics of the basin. In this context, the objective of this work was to develop the modeling of catchment basin of the river Jundiaí - RN and carry out the study of attenuation of a flood of the dam Tabatinga, by means of a monitoring project of hydrological data and climatology of the basin, with a view to promoting the development of research activities by applying methodologies unified and appropriate for the assessment of hydrological studies in the transition region of the semiarid and the forest zone on the coast of Rio Grande do Norte. For the study of the hydrological characteristics of the basin was conducted the automatic design of the basin of the river Jundiaí, with the aid of programs of geoprocessing, was adopted a hydrological model daily, the NRCS, which is a model determined and concentrated. For the use of this model was necessary to determine some parameters that are used in this model, as the Curve Number. Having in mind that this is the first study that is being conducted in the basin with the employment of this model, it was made sensitivity analysis of the results of this model from the adoption of different values of CN, situated within a range appropriate to the conditions of use, occupation and the nature of the soil of this basin. As the objective of this study was also developing a simulation model of the operation of the Tabatinga dam and with this flood control caused in the city of Macaíba, it was developed a mathematical model of fluid balance, developed to be used in Microsoft Excel. The simulation was conducted in two phases: the first step was promoted the water balance daily that allowed the analysis of the sensitivity of the model in relation to the volume of waiting, as well as the determination of the period of greatest discharges daily averages. From this point, it was assumed for the second stage, which was in the determination of the hydrograph of discharges effluent slots, that was determined by means of the fluid balance time, on the basis of the discharges effluents generated by a mathematical equation whose parameters were adjusted according to the hydrograph daily. Through the analyzes it was realized that the dam Tabatinga only has how to carry out the attenuation of floods through the regularization of the volume of waiting, with this there is a loss of approximately 56.5% on storage capacity of this dam, because for causing the attenuation effect of filled the shell of this dam has to remain more than 5m below the level of the sill, representing at least 50.582.927m3. The results obtained with the modeling represents a first step in the direction of improving the level of hydrological information about the behavior of the basins of the semiarid. In order to monitor quantitatively the hydrographic basin of the river Jundiaí will be necessary to install a rain gauge register, next to the Tabatinga dam and a pressure transducer, for regular measurements of flow in the reservoir of the dam. The climatological data will be collected in full automatic weather station installed in Agricultural School Jundiaí

O que controla o crescimento do Fitoplâncton em lagoas costeiras tropicais? um modelo para a lagoa de Extremoz (RN)

The phytoplankton growth is dependent of several abiotic (nutrients, temperature) and biotic (predation by zooplankton) variables. In this work, a mathematical model was developed in Stella software to understand the planktonic dynamics of Extremoz Lagoon (RN) and to simulate scenarios of different environmental conditions. Data were collected monthly at two points of the lagoon. The state variables are phytoplankton and zooplankton and forcing variables are nitrogen, phosphorus and temperature. The results show that: a) the model are well coupled, especially when some constants assume different values; b) simulated nutrient concentrations reduction decreases phytoplankton biomass, but the increase of nutrients does not stimulate the growth; c) changes in the temperature does not change the phytoplankton biomass; d) changes in zooplankton biomass affect directly and reduces the phytoplankton, indicating a topdown control mechanism; e) changes in the nutrient concentration modified the biomass of zooplankton suggesting a rapid flow of energy between nutrients, phytoplankton and zooplankton and a ecosystem likely arranged in an inverted pyramid (higher concentration of zooplankton than phytoplankton)

Trabalhos prático-experimentais no ensino da biologia: Uma análise dos livros didáticos de Biologia aprovados no PNLD/2012

El trabajo práctico experimental en la educación en Ciencias y en el contexto de la enseñanza de la Biología es un objetivo clave. Teniendo en cuenta la influencia de los libros de texto en la actividad profesional de docentes, interesado en este estudio para caracterizar la orientación de este tipo de materiales, para el trabajo práctico experimental y el uso de la medición en esta actividad. Para ello analizaron las ocho colecciones de libros de Biología aprobado en PNLD en 2012. La investigación es de naturaleza descriptiva e interpretativa y de recogida de datos ha sido elegida por el método de análisis de contenido (BARDIN, 2002). El análisis de los trabajos práctico experimentales buscó caracterizar su naturaleza epistemológica, concepción de la ciencia implícita, conceptual, tipología, contenido conceptual de Biología utilizado, cuántos implican medidas, y cómo se utiliza en este contexto según el procedimiento general para medir propuesto por Núñez y Silva (2008). Los trabajo práctico experimental ha sugerido una epistemología de la enseñanza conceptual, carácter racionalista en su mayoría y dominada por las actividades del tipo de ejercicio práctico, a necesidad de medir está presente en una minoría de estos y se se utiliza el procedimiento general de medición de forma parcial e implícito en la mayoría de los trabajos prático experimentales. Por lo tanto, proponemos en este actividades de estudio a desarrollar una guía de análisis de los trabajo práctico experimentales propuesto en los libros de texto de Biología

Controle profissional de biofilme dentário como estratégia para manutenção da saúde periodontal de pacientes com aparelho ortodôntico fixo: análise comparativa entre diferentes períodos

The presence of fixed orthodontics appliances interfere on sanitation, allowing periodontal diseases to appear, despite the fact patients keep on visiting the dentist every month. This research aims to determine a protocol for the mechanical control of the dental biofilm performed by the professional. A protocol that was able to maintain the periodontal health of the patients under orthodontic treatment with fixed appliances, and in order to do so, it used a non-controlled, randomized and blind clinical essay. The sample involved 40 adolescents who were under the installation of fixed orthodontics appliances and it was divided in three groups, as follows: monthly controlled group (group 1) composed of 11 patients, the quarterly controlled group (group 2) with 16 patients and the semestrial controlled group (group 3) with 13 patients. For data collection, an interview and clinical exams with probing depth measurement, quantity of keratinized mucosa, Gingival Index and the Plaque Index were used. On the initial exam all patients received brushing guidelines as well as the professional control of dental biofilm, with periodontal scaler, Robinson s brush and prophylactic paste. However, Group 1 returned every month for control procedures; Group 2 every three months and Group 3 after six months. The intervention had a six-month duration (for all the three groups), when all the exams were repeated by another examiner who did not know which group each patient was inserted in. Finally, the research concluded that despite the fact there is no statistically significant difference among the three groups, clinically the patients from the monthly group presented a better response to professional control, with less accumulation of dental biofilm and less rate of gingival inflammation. Thus, the mechanical control of the dental biofilm performed by the professional could not avoid gingival increase, characterized by the raise of probing depth measurement, neither the quantity of keratinized mucosa

Comportamento e ecologia acústica da baleia jubarte (Megaptera novaeangliae) na região Nordeste do Brasil

The acoustic ecology concept involve the relation between the live organisms and their sound environment and is applied in the present work to study the context in which the humpback whale (Megaptera novaeangliae) singing behavior, known as the most complex display in the nature, occurred in the northeastern Brazilian coast, outside the core area of Abrolhos Bank, between 2005 and 2010.I analyze the singer male occurrence , their spatial distribution and probable relations with oceanographic features, such as depth, tide regimen and moon phases. I also describe the acoustic structure and temporal variation of the singing behavior, based on song frequency and time measurements outside the Abrolhos Bank, and further compare the song complexity, registered in the same period, between Abrolhos Bank (16°- 19° S, 37°- 39° W) and the adjacent North Coast, herein considered from Itacaré (14° S, 38° W) to Aracaju (11° S, 37° W). Additionally, I look for describe and analyze anthropogenic noise sources in the marine environment of the study area, produced by the oil industry as well as by the whale watching operation, relating their frequencies to the acoustic niche utilized by the humpbacks. The results indicated a great plasticity in the singing behavior, evidenced by the occurrence of singer males in diverse social structures, from solitary individuals to other groups, even containing females and calves, as well as by the diversity which compound the song, when compared between two regions inside the same breeding area, which present distinct oceanographic characteristics. The singer male distribution may be related with the continental shelf extent along the study area. The anthropogenic noise presented frequency range, amplitude and sound intensity in potential to interfere acoustically in the singing behavior of the species, may resulting in disturbance during the breeding season in the Brazilian coast. Implications about the obtained results in the humpback whale mating system are discussed. In this way, I pretend to contribute with the acoustic ecology subject and provide information to subsidize humpback whale conservation

Análises bromatológicas e fitoquímicas de frutos de Licania tomentosa (Benth) FRITSCH

This study conducted chemical analyzes of the fruits of Licania tomentosa Benth belonging to the Chrysobalanaceae family, order and superorder Rosiflorae Rosales. Samples were collected in February 2011 in the city of Natal - RN. The fruits were separated into peel, pulp and seed, and the samples were analyzed on moisture and ash by thermogravimetric methods, reducing and total sugars, lipids by Soxhlet extraction, minerals by ICP / OES and other analyzes by physical measurements of the fruit. The fruits for the analysis of determination of flavonoids and phenolic compounds were dried at 40 ° C and ground. For the analyzes to determine the content of phenolics and flavonols was used spectroscopy in the visible region, and also performed the characterization of ethanol extracts by high performance liquid chromatography and test for antioxidant activity hydroethanolic extracts. The results obtained are about 83.9% of the fruits have a length between 4.0 to 6.0 cm with respect to the diameter of the fruit about 97.4% of the fruits have a diameter between 2.0 - 4, 0 cm, mean weight of 36.14 g (7.86), the bark showed 60.5 (1.5)% relative humidity, the flesh 72.3 (0.9) and 44.4 seeds (0.4 )%, the bark showed 0.22 (0.00)% ash, the pulp 1.41 (0.01)% and the seed 1.18 (0.01)%, the bark showed 3.73 (0, 09) mg lipids / 100 g sample of the pulp 0.40 (0.04) and the seed 0.05 (0.00). With respect to reducing sugars and total gave the results, 16.23 (0.23) g/100g and 20.70 (0.24) g/100g. The fruit is presented with a good source of nutrients especially carbohydrates and lipids. The analysis for determining the antioxidant activity tests were performed reducing power and antioxidant capacity, the antioxidant capacity of hydroethanolic extracts of peel and pulp showed similar results, with higher concentrations however hydroethanolic bark extract. Regarding the content of phenolics and flavonoids hidroetanílico bark extract showed higher concentration values. The characterization of the extracts by high performance liquid chromatography identified the following compounds by retention time indicated by the race of the standards: galic acid, kaempferol and kaempferol derivatives. Considering the results of the fruit Licania tomentosa Benth may be an alternative food by analysis of their nutritional content and has substances with antioxidant action

Revitalização do Rio Golandim (RN/Brasil) após décadas de contaminação por efluentes industriais e domésticos: este rio está recuperado?

Environmental pollution causes the loss of the quality of aquatic resources and also affects the health of human beings. The Golandim River is located in São Gonçalo do Amarante (RN Brazil) and had its water recovered seven years ago by measurements of parameters of the water s quality analyses physicochemistry, microbiological and heavy metals. However, it is not well established if this river is truly recovered, so this study provides a wide knowledge about the quality of these waters. Therefore, this investigation was accomplished by assays of ecotoxicology utilizing Ceriodaphnia dubia and of genotoxicity of the river s water using a biomarker Tradescantia Pallida (Trad-MCN). In set, it carried through a study of environmental perception through questionnaires that approached questions related to the profile of the interviewed one, knowledge on the environment and of the river Golandim with the community that lives in the neighborhoods of the river to diagnosis as they perceive the environment where live and its problems. The assays of the water had been carried out by collecting samples in three different sites of the Golandim River. They were collected between the periods of December 2010 (dry season in the northeast of Brazil) and July 2011 (rainy season in the northeast of). The analysis of the data allowed observing that the majority of the inhabitants are adult and presents a global vision of what it is part of the environment, the majority mentions the pollution of the river as one of the problems of the city, considering it serious. The ecotoxicology assay showed that there was not acute toxicity in all three samples collected. Meanwhile, all these three samples demonstrated significant chronic toxicity. The results from the Trad-MCN assay presented an increase in the frequency of micronucleus in one of the sites analyzed (S3) (p<0.01), in both seasons collected. On the other hand, the sites S1 and S2 did not presented a significant increase of micronucleus using this bioassay. The analyses of chemicals detected an increase in the levels of some metals, in different seasons and samples, which can be associates with some compounds found in urban and industrial areas. On the other hand, the physicochemistries parameters demonstrated that the Golandim River is recouped, when compared with the values presented at the CONAMA s legislation. However, these results indicate the presence of compounds capable of inducing chromosomal mutation in plants. On the other hand, the parameters physicistchemistries demonstrate that the river Golandim is if recouping, since when compares the values observed with the legislation of the CONAMA. All these results point to the fact that the Trad-MCN assay was sensitive and efficient biomarker for chromosomal instability and the C. dubia ecotoxicology assay was as though an efficient biomarker of toxicity of water s quality. The results from Trad-MCN associated with the ecotoxicology demonstrates that these analyses are important for environmental monitoring, once the first bioassay described above indicates alterations at the standards of cells and the other one indicates alterations at the standards of organisms. This study alerts for the necessity to carry out biological assays for the analyses of the water s quality

Uma nova proposta de antena planar multibanda para comunicações móveis

The great interest observed in wireless communication systems has required the development of new configurations of microstrip antennas, because they are easily built and integrated to other microwave circuit components, which is suitable for the construction and development of planar antenna arrays and microwave integrated circuits. This work presents a new configuration of tapered microstrip antenna, which is obtained by impressing U-slots on the conducting patch combined with a transmission line matching circuit that uses an inset length. It is shown that the use of U-slots in the microstrip antenna conducting patch excites new resonating modes, that gives a multiband characteristic for the slotted microstrip antenna, that is suitable for applications in communication systems that operates several frequencies simultaneously. Up to this date, the works reported in the literature deals with the use of Uslotted microstrip rectangular antennas fed by a coaxial probe. The properties of a linear array of microstrip patch tapered antennas are also investigated. The main parameters of the U slotted tapered microstrip antennas are investigated for different sizes and locations of the slots impressed on the conducting patch. The analysis of the proposed antenna is performed by using the resonant cavity and equivalent transmission line methods, in combination with a parametric study, that is conducted by the use of the Ansoft Designer, a commercial computer aided microwave software well known by its accuracy and efficiency. The mentioned methods are used to evaluate the effect in the antennas parameters, like resonant frequency and return loss, produced by variations of the antenna structural parameters, accomplished separately or simultaneously. An experimental investigation is also developed, that consists of the design, construction and measurement of several U slotted microstrip antenna prototypes. Finally, theoretical and simulated results are presented that are in agreement with the measured ones. These results are related to the resonating modes identification and to the determination of the main characteristics of the investigated antennas, such as resonant frequency, return loss, and radiation pattern

Uso do GPR na geração de modelos estáticos 3D para o planejamento de lavra de minerais pesados depositados em dunas eólicas

This project was developed as a partnership between the Laboratory of Stratigraphical Analyses of the Geology Department of UFRN and the company Millennium Inorganic Chemicals Mineração Ltda. This company is located in the north end of the paraiban coast, in the municipal district of Mataraca. Millennium has as main prospected product, heavy minerals as ilmenita, rutilo and zircon presents in the sands of the dunes. These dunes are predominantly inactive, and overlap the superior portion of Barreiras Formation rocks. The mining happens with the use of a dredge that is emerged at an artificial lake on the dunes. This dredge removes sand dunes of the bottom lake (after it disassembles of the lake borders with water jets) and directs for the concentration plant, through piping where the minerals are then separate. The present work consisted in the acquisition external geometries of the dunes, where in the end a 3D Static Model could be set up of these sedimentary deposits with emphasis in the behavior of the structural top of Barreiras Formation rocks (inferior limit of the deposit). The knowledge of this surface is important in the phase of the plowing planning for the company, because a calculation mistake can do with that the dredge works too close of this limit, taking the risk that fragments can cause obstruction in the dredge generating a financial damage so much in the equipment repair as for the stopped days production. During the field stages (accomplished in 2006 and 2007) topographical techniques risings were used with Total Station and Geodesic GPS as well as shallow geophysical acquisitions with GPR (Ground Penetrating Radar). It was acquired almost 10,4km of topography and 10km of profiles GPR. The Geodesic GPS was used for the data geopositioning and topographical rising of a traverse line with 630m of extension in the stage of 2007. The GPR was shown a reliable method, ecologically clean, fast acquisition and with a low cost in relation to traditional methods as surveys. The main advantage of this equipment is obtain a continuous information to superior surface Barreiras Formation rocks. The static models 3D were elaborated starting from the obtained data being used two specific softwares for visualization 3D: GoCAD 2.0.8 and Datamine. The visualization 3D allows a better understanding of the Barreiras surface behavior as well as it makes possible the execution of several types of measurements, favoring like calculations and allowing that procedures used for mineral extraction is used with larger safety