On configuration of exchanged La3+ on ZSM-5: A theoretical approach to the improvement in hydrothermal stability of La-modified ZSM-5 zeolite

Density functional calculations have been employed to investigate the locating and binding of lanthanum cation, i.e., La(OH)(2)(+), on HZSM-5 zeolite. Through geometry optimization, it was determined that lanthanum ions are favorably accommodated in the two 6-T rings of the straight channels (Clusters 1 and 2, see Sec. III A for details). Cluster 1 was found to exist in prior to Cluster 2 due to the preference of Al substitution in the T11 site (Cluster 1) rather than in the T8 site (Cluster 2). Geometry-optimization of Cluster 1 containing another two lanthanide ions Nd3+ and Yb3+ was also carried out and it was found that a monotonic decrease in Ln-O bond length will take place as the atomic number increases, conforming well to the rule of lanthanide contraction. Some of the optimized parameters are comparable to the corresponding experimental values in Y zeolite, which confirms that the optimized configurations are acceptable. The average frequencies of hydroxyls attached to La3+ or Yb3+ in Cluster 1 fall at 3609.16 and 3579.76 cm(-1), respectively, with the gap of these two frequencies close to that in the sodalite cage of Y zeolite. Compared to H-form zeolite, the charges on both Al and O atoms in Ln-ZSM-5 zeolite show an obvious increase, which will undoubtedly lead to a stronger mutual interaction and hence enhance the stability of the [AlO4](-) anion. Moreover, the Ln(OH)(2)(+) seem to have thickened the zeolite framework, which can effectively retard the process of dealumination. Through the evaluation of the possibility for dimer formation, it turned out that when the exchange degree arrived to approximately 0.28, lanthanum monomers began to aggregate into dimers, and were completely converted into dimers when the exchange degree approached 0.60. (C) 2003 American Institute of Physics.

Synthesis and characterization of novel neutral nickel complexes bearing fluorinated salicylaidiminato ligands and their catalytic behavior for vinylic polymerization of norbornene

A series of salicylaldimine-based neutral Ni(II) complexes (3a-j) [ArN = CH(C6H40)]Ni(PPh3)Ph [3a,Ar = C6H5; 3b,Ar = C6H4F(o); 3c, Ar = C6H4F(m); 3d, Ar = C6H4F(p); 3e, Ar = C6H3F2(2,4); 3f, Ar = C6H3F2(2,5); 3g, Ar = C6H3F2(2,6); 3h, Ar = C6H3F2(3,5); 3i, Ar = C6H2F3(3,4,5); 3j, Ar = C6H5] have been synthesized in good yield, and the structures of complexes 3a and 3i have been confirmed by X-ray crystallographic analysis. Using modified methylaluminoxane as a cocatalyst, these neutral Ni(II) complexes exhibited high catalytic activities for the vinylic polymerization of norbornene.

Carbon dioxide/propylene oxide coupling reaction catalyzed by chromium salen complexes

A series of chromium/Schiff base complexes N,N'-bis(salicylidene)-1,2-phenylenediamino chromium(III) X were prepared and employed for the alternating copolymerization of carbon dioxide with racemic propylene oxide in the presence of (4-dimethylamino)pyridine. The effect of the complex structure and reaction conditions on the catalytic activity, the poly(propylene carbonate)/cyclic carbonate (PPC/PC) selectivity, and the polymer head-to-tail linkages was examined. The experiments indicated that N,N'-bis(3,5-di-tert-butylsalicylidene)-1,2-phenylenediamino chromium(III) (NO3) exhibited the highest PPC/PC selectivity as well as polymer head-to-tail linkages and N,N'-bis(3,5-dichlorosalicylidene)-1,2-phenylenediimino chromiu(III) (NO3) possessed the highest catalytic activity among these chromium/Schiff base complexes. The structure of the produced copolymer was characterized by the IR, H-1 NMR, and C-13 NMR measurements.

Preparation of methyl tert-butyl ether (MTBE) over heteropoly acids immobilized on activated carbon (HPA/C) in the vapor phase

Heteropolyacids (HPAs) supported on the activated carbon (SiW12/C and PW12/C) have been used to study the formation of methyl tert-butyl ether (MTBE). Compared to the conventional commercial catalysts, Amberlyst-15 resin and HZSM-5, HPAs supported catalysts have been proved to have much higher catalytic activity under lower temperature, especially selectivity to MTBE is up to 100%. It may be due to the high acid strength of HPAs as well as the specialty of heteropolyanion.

A high coking-resistance catalyst for methane aromatization

Steaming-dealuminated HZSM-5-supported molybdenum catalysts have been found to be high coking-resistance catalysts for methane aromatization reactions; compared with conventional catalysts, they give a much higher selectivity towards aromatics.

An integrated air-POM syngas/dimethyl ether process from natural gas

A Cu-Zn-Al methanol catalyst combined with HZSM-5 was used for dimethyl ether (DME) synthesis from a syngas containing nitrogen, which was produced by air-partial oxidation of methane (air-POM). Air-POM occurred at 850 degreesC, 0.8 MPa, CH4/air/H2O/CO2 ratio of 1/2.4/0.8/0.4 over a Ni-based catalyst modified by magnesia and lanthanum oxide with 96% CH4 conversion and constantly gave syngas with a H-2/CO ratio of 2/1 during a period of 450 h. The obtained N-2-containing syngas was used directly for DME synthesis. About 90% CO per-pass conversion, 78% DME selectivity and 70% DME yield could be achieved during 450 h stability testing under the pressure of 5.0 MPa. the temperature of 240 degreesC and the space velocity of 1000 h(-1). (C) 2002 Elsevier Science B. V. All rights reserved.

The effect of chromium on sulfur resistance of Pd/HY-Al2O3 catalysts for aromatic hydrogenation

Sulfur is a major poison to noble metal catalysts for deep aromatic hydrogenation in the petroleum refining industry. In order to study the sulfur resistance of Pd-based catalysts, a series of Pd, Cr, and PdCr catalysts supported on HY-Al2O3 were studied by NH3-TPD, pyridine-adsorption IR, TPR, IR spectra of adsorbed CO, and toluene hydrogenation in the presence of 3000 ppm sulfur as thiophene under the following conditions: 533-573 K, 4.2 MPa, and WHSV 4.0 h(-1). Cr has no influence on the acidity of the catalysts. TPR patterns and in situ IR spectra of adsorbed CO revealed a strong interaction between Cr and Pd, and the frequency shift of linear bonded CO on Pd indicates that the electron density of Pd decreases with the increase of the Cr/Pd atomic ratio. The catalytic performance of Pd, Cr, and PdCr catalysts shows that the sulfur resistance of Pd is strongly enhanced by Cr, and the activity reaches its maximum when the Cr/Pd atomic ratio equals 8. The active phase model "Pd particles decorated by Cr2O3" is postulated to explain the behavior of PdCr catalysts. (C) 2001 Academic Press.

Bimetallic effects in the liquid phase hydrogenation of 2-butanone

A series of bimetallic Ru-containing monometallic and bimetallic catalysts were prepared and tested for their activity for the hydrogenation of 2-butanone to 2-butanol at 30 °C and 3 bar H2. RuPt bimetallic catalysts were the most active for the reaction, with a ratio of 5 wt% Ru:1 wt% Pt on activated carbon (AC) found to be optimum. The activity of this bimetallic catalyst was more than double that of the sum of the activities of the monometallic Ru and Pt catalysts, providing evidence of a “bimetallic” effect. Structural analysis of the bimetallic catalysts revealed that they consisted of clusters of particles of the order of 1–2 nm. Extended X-ray absorption fine structure analysis showed that there were two types of particle on the surface of the bimetallic RuPt catalyst, specifically monometallic Ru and bimetallic RuPt particles. For the bimetallic particles, it was possible to fit the data with a model in which a Ru core of 1.1 nm is enclosed by two Pt-rich layers, the outer layer containing only 13 at% Ru. Pretreatment of the monometallic and bimetallic catalysts in hydrogen had a significant effect on the activity. Both the bimetallic and monometallic Ru-based catalysts showed a trend of decreasing activity with increasing temperature of prereduction in hydrogen. This loss of activity was almost fully reversible by exposure of the catalysts to air after reduction. The changing activity with exposure to different gas phase environments could not be attributed to changes in particle size or surface composition. It is proposed that the introduction of hydrogen results in a gradual smoothing of the surface and loss of defect sites; this process being reversible on introduction of air. These defect sites are particularly important for the dissociative adsorption of hydrogen, potentially the rate-determining step in this reaction.

A review of the effect of the addition of hydrogen in the selective catalytic reduction of NOx with hydrocarbons on silver catalysts

Research is progressing fast in the field of the hydrogen assisted hydrocarbon selective catalytic reduction (HC-SCR) over Ag-based catalysts: this paper is a review of the work to date in this area. The addition of hydrogen to the HC-SCR reaction feed over Ag/Al2O3 results in a remarkable improvement in NO (x) conversion using a variety of different hydrocarbon feeds. There is some debate concerning the role that hydrogen has to play in the reaction mechanism and its effect on the form of Ag present during the reaction. Many of the studies use in situ UV-Vis spectroscopy to monitor the form of Ag in the catalyst and appear to indicate that the addition of hydrogen promotes the formation of small Ag clusters which are highly reactive for NO (x) conversion. However, some authors have expressed concern about the use of this technique for these materials and further work is required to address these issues before this technique can be used to give an accurate assessment of the state of Ag during the SCR reaction. A study using in situ EXAFS to probe the H-2 assisted octane-SCR reaction has shown that small Ag particles (containing on average 3 silver atoms) are formed during the SCR reaction but that the addition of H-2 to the feed does not result in any further change in the Ag particle size. This points to the direct involvement of H-2 in the reaction mechanism. Clearly the addition of hydrogen results in a large increase in the number and variety of adsorbed species on the surface of the catalyst during the reaction. Some authors have suggested that conversion of cyanide to isocyanate is the rate-determining step and that hydrogen promotes this conversion. Others have suggested that hydrogen reduces nitrates to more reactive nitrite species which can then activate the hydrocarbon; activation of the hydrocarbon to form acetates has been proposed as the key step. It is probable that all these promotional effects can take place and that it very much depends on the reaction temperature and feed conditions as to which one is most important.

Steam reforming of model compounds and fast pyrolysis bio-oil on supported noble metal catalysts

The production of hydrogen by steam reforming of bio-oils obtained from the fast pyrolysis of biomass requires the development of efficient catalysts able to cope with the complex chemical nature of the reactant. The present work focuses on the use of noble metal-based catalysts for the steam reforming of a few model compounds and that of an actual bio-oil. The steam reforming of the model compounds was investigated in the temperature range 650-950 degrees C over Pt, Pd and Rh supported on alumina and a ceria-zirconia sample. The model compounds used were acetic acid, phenol, acetone and ethanol. The nature of the support appeared to play a significant role in the activity of these catalysts. The use of ceria-zirconia, a redox mixed oxide, lead to higher H-2 yields as compared to the case of the alumina-supported catalysts. The supported Rh and Pt catalysts were the most active for the steam reforming of these compounds, while Pd-based catalysts poorly performed. The activity of the promising Pt and Rh catalysts was also investigated for the steam reforming of a bio-oil obtained from beech wood fast pyrolysis. Temperatures close to, or higher than, 800 degrees C were required to achieve significant conversions to COx and H-2 (e.g., H-2 yields around 70%). The ceria-zirconia materials showed a higher activity than the corresponding alumina samples. A Pt/ceria-zirconia sample used for over 9 h showed essentially constant activity, while extensive carbonaceous deposits were observed on the quartz reactor walls from early time on stream. In the present case, no benefit was observed by adding a small amount of O-2 to the steam/bio-oil feed (autothermal reforming, ATR), probably partly due to the already high concentration of oxygen in the bio-oil composition. (c) 2005 Elsevier B.V. All rights reserved.

Acidic properties of nanolayered ZSM-5 zeolites

The acidic properties of nanolayered ZSM-5 zeolites synthesized with the aid of multiquaternary ammonium surfactants were investigated in detail. A substantial fraction of Al is present in highly dispersed form at extraframework positions indicative of the defective nature of the calcined nanolayered zeolites. Acidity characterization reveals that the Brønsted acid sites are similar in strength to those in bulk HZSM-5. Nanolayered zeolites contain a higher amount of Brønsted acid sites (BAS) at their external (mesopore) surface. Unilamellar zeolites have a higher concentration of external BA and silanol sites than multilamellar ones. The number of BAS in the nanolayered zeolites is considerably lower than the tetrahedral Al content, the difference increasing with nanolayer thickness. Except for one particular sample (nanolayered ZSM-5 synthesized from COH template), the total turnover of methanol normalized per BAS trends inversely with the concentration of BAS. There is no correlation with the concentration of external BAS. Catalyst deactivation due to coke mainly depends on the BAS concentration. A unilamellar ZSM-5 zeolite prepared using COH displayed substantially improved performance in terms of a much lower rate of coke deactivation in line with earlier data Choi et al. [10]. Since the acidic and textural properties of this zeolite did not differ significantly from the others, it remains to be determined why this zeolite performs so much better. © 2013 Elsevier Ltd. All rights reserved.

The effects of stepped sites and ruthenium adatom decoration on methanol dehydrogenation over platinum-based catalyst surfaces

A density functional theory study of methanol dehydrogenation over stepped Pt(2 1 1) surfaces without and with Ru modification was carried out to understand fuel catalytic reactions on Pt-based catalysts. Two main pathways of the CH3OH dehydrogenation were examined: the O–H pathway which was initiated by O–H bond scission to form the methoxy (CH3O) intermediate followed by sequential cleavage of C–H bonds to CO, and the C–H pathway which was initiated by C–H bond scission to form the hydroxymethyl (CH2OH) followed by two C–H bond cleavages to COH and then CO. Possible crossover reactions between the O–H and C–H pathways were also computed. Compared to flat Pt(1 1 1), stepped Pt(2 1 1) increases the adsorption energies of intermediates, making no significant contribution to decreasing the reaction barriers of most elementary steps involved, except in the first hydrogen scission. However, on the Ru-modified surface, a significant reduction was found in reaction barriers for the first step of the C–H bond scission and a number of further dehydrogenation steps crossing over to the O–H pathway, with the most facile paths identified. Our data reveals the complexity of methanol catalytic reaction processes at the atomic level and contributes to a fundamental understanding of fuel reactions on Pt-based catalysts.

The interaction between adsorbed OH and O-2 on TiO2 surfaces

Reduced TiO2 (110) surfaces usually have OH groups as a result of H2O dissociation at oxygen vacancy defects. Because of excess electrons due to OH adsorption, OH/TiO2. exhibit interesting properties favorable to further O-2 or H2O adsorption. Both O-2 and H2O can adsorb and easily diffuse on the OH/TiO2 surface; such behavior plays a significant role in photocatalysis, heterogeneous catalysis, electronic devices and sensors. Indeed, the processes of H2O dissociation, O-2 and H2O diffusion on Such TiO2 surfaces, in the presence of OH groups, are important issues in their own right. Herein, the most recent experimental and theoretical progresses in understanding the interactions between adsorbed OH groups and O-2, or H2O, over TiO2 (110) surfaces and their implications will be reviewed. (c) 2009 Elsevier Ltd. All rights reserved.

Catalisadores ou precursores de espécies activas à base de molibdénio

Atendendo à produção de epóxidos em larga escala e à sua importância como intermediários versáteis, muita atenção tem sido dada à epoxidação de olefinas. Destaca-se a implementação do processo industrial de epoxidação de propileno em fase líquida com tBHP, usando complexos de molibdénio como catalisadores homogéneos (Halcon-ARCO). Neste trabalho foram investigados novos complexos à base de molibdénio como catalisadores (ou precursores) para epoxidação de olefinas em fase líquida. Foi objecto de estudo a identificação das espécies activas e a estabilidade dos catalisadores através da sua separação no final das reacções catalíticas, caracterização e reutilização. Escolheu-se como reacção modelo a epoxidação do ciscicloocteno com tBHP (em decano, tBHPdec), a 55 ºC. Estendeu-se o estudo dos desempenhos catalíticos a diferentes substratos, oxidantes, solventes e métodos de aquecimento. A maior actividade catalítica foi observada para os complexos [MoO2Cl2L2] (L=ligando dialquilamida), mais estáveis e fáceis de manusear que [MoO2Cl2] e complexos análogos com L {THF, MeCN} (Cap. 2). A partir destes complexos podem-se formar in situ espécies activas intermediárias do tipo [(MoO2ClL2)2(μ-O)]. O complexo [MoO2(Lzol)], Lzol= ligando oxazolina quiral (Cap. 3), é um catalisador estável e versátil, activo para a epoxidação de diversas olefinas (selectividades elevadas para epóxidos, mas enantioselectividades baixas), desidrogenação oxidativa de álcoois e sulfoxidação de sulfuretos. O catalisador foi também reciclado eficientemente, usando um líquido iónico (LI). O complexo iónico [MoO2Cl{HC(3,5-Me2pz)3}]BF4 (Cap.4) converteu-se nos complexos activos [{MoO2(HC(3,5-Me2pz)3)}2(μ-O)](BF4)2, [Mo2O3(O2)2(μ-O){HC(3,5-Me2pz)3}] e [MoO3{HC(3,5-Me2pz)3}]; quando dissolvido num LI, o catalisador foi reciclado com sucesso. A presença de água e o meio oxidante influenciaram a formação destas espécies. Os complexos [CpMo(CO)3Me] (Cap.5) e [CpMo(CO)2(η3- C3H5)] (Cap.6) originaram espécies activas similares (baseado nos testes catalíticos e nos espectros FT-IR ATR dos sólidos recuperados). Para [Cp'Mo(CO)2(η3-C3H5)], a influência do Cp' na actividade catalítica sugeriu a formação de espécies activas com este ligando. A partir dos complexos [Mo(CO)4L] formaram-se in situ catalisadores estáveis, que podem ser heterogéneos: para L=2-[3(5)-pirazolil]piridina formou-se [Mo4O12L4]; para L=[3- (2-piridil)-1-pirazolil]acetato de etilo formou-se [Mo8O24L4] (Cap.7). O uso de microondas (MO) como método de aquecimento em vez de um banho de óleo (BO) resultou no aumento da velocidade da reacção catalítica, devido ao aquecimento mais rápido da mistura reaccional (Caps. 5 e 7). A utilização da solução aquosa de tBHP em vez de tBHPdec era preferível, porque excluía o decano do sistema reaccional e mantinham-se elevados os rendimentos em epóxido (Caps. 2 e 6); optimizou-se o desempenho catalítico removendo a água das misturas reaccionais (Caps. 4 e 7). O melhor resultado para a epoxidação de limoneno foi observado para [CpMoCO3Me]: 88% de rendimento em epóxido (2 h, 55 ºC, método de aquecimento MO).

A comparative study of medium and large pore zeolites in alkylation reactions

In this thesis an attempt has been made to compare the catalytic activity of some medium and large pore zeolites in a few alkylation and acylation reactions. The work reported in the present study is basically centered around the following zeolites namely, ZSM-5, mordenite, zeolite Y and beta. The major reactions carried out were benzoylation of o-xylene, propionylation of toluene and anisole and benzylation of 0xylene.The programme involves the synthesis, modifications and characterization of the zeolite catalysts by various methods. The influence of various parameters such as non-framework cations, Si/AI ratio of zeolites, temperature of the reaction, catalyst concentration, molar ratio of the reactants and recycling of the catalysts were also examined upon the conversion of reactants and the formation of the desired products in the alkylation / acylation reactions.The general conclusions drawn by us from the results obtained are summarized in the last chapter of the thesis. Zeolite beta offers interesting opportunities as a potential catalyst in alkylation reactions and the area of catalysis by medium and large pore zeolites is very fascinating and there is plenty of scope for further research in this field. Moreover, zeolite based catalysts are effective in meeting current industrial processing and more stringent environment pollution limits.