Experimental investigation of soil and groundwater impacts caused by vinasse disposal

The problems caused by the residual effluents of wine distilleries for alcohol production are well known. The effluent effects in soil and groundwater are being researched in an area with sugar cane culture which receives, yearly, vinasse by dispersion. Samples are being collected from the soil, the groundwater and the existing creeks in the area. Four sub-areas are being monitored separately with a vinasse application of 300 m 3/ha year. Experimentation periods in each area have been 0, 5, 10 and 15 years. In the unsaturated zone, samples are being collected at depths of 25, 75 and 150 cm. The chemical analyses include macro and micro nutrients, organic matter and pH. Physical analyses give the soil water retention, hydraulic conductivity and soil particle distribution. These measurements permit the evaluation of nitrogen absorption and fertility changes of the soil. A tendency for the maintenance of soil fertility can be observed but with an elevation of nitrate concentration in groundwater.

Comparative analysis between biogas flow in landfill and electrical resistivity tomography in Rio Claro city, Brazil

The biogas originated from anaerobic degradation of organic matter in landfills consists basically in CH4, CO2, and H2O. The landfills represent an important depository of organic matter with high energetic potential in Brazil, although with inexpressive use in the present. The estimation of production of the productive rate of biogas represents one of the major difficulties of technical order to the planning of capture system for rational consumption of this resource. The applied geophysics consists in a set of methods and techniques with wide use in environmental and hydrogeological studies. The DC resistivity method is largely applied in environmental diagnosis of the contamination in soil and groundwater, due to the contrast of electrical properties frequent between contaminated areas and the natural environment. This paper aims to evaluate eventual relationships between biogas flows quantified in drains located in the landfill, with characteristic patterns of electrical resistivity in depth. The drain of higher flow (117 m3 /h) in depth was characterized for values between 8000 Ω⋅m and 100.000 Ω⋅m, in contrast with values below 2000 Ω⋅m, which characterize in subsurface the drain with less flow (37 m3 /h), besides intermediary flow and electrical resistivity values, attributed to the predominance of areas with accumulation or generation of biogas.

Origin of the groundwater salinization in La Aldea coastal aquifer (Gran Canaria, Canary Islands)

[EN] Groundwater chemistry in La Aldea aquifer (Gran Canaria, Canary Islands) shows high contents of chloride and nitrate ions. The salinization process has been modelled using the geochemical data, taking into account the results of a previous flow model. The results allow to identify the salinity of the recharge from the rainfall under aridity conditions and the irrigation returns like the main causes of the groundwater salinization.

Aerobic biodegradation of chlorinated solvents and plastics in batch and continuous-flow bioreactors: process development, and identification of suitable chemical pre-Treatments

The purpose of the first part of the research activity was to develop an aerobic cometabolic process in packed bed reactors (PBR) to treat real groundwater contaminated by trichloroethylene (TCE) and 1,1,2,2-tetrachloroethane (TeCA). In an initial screening conducted in batch bioreactors, different groundwater samples from 5 wells of the contaminated site were fed with 5 growth substrates. The work led to the selection of butane as the best growth substrate, and to the development and characterization from the site’s indigenous biomass of a suspended-cell consortium capable to degrade TCE with a 90 % mineralization of the organic chlorine. A kinetic study conducted in batch and continuous flow PBRs and led to the identification of the best carrier. A kinetic study of butane and TCE biodegradation indicated that the attached-cell consortium is characterized by a lower TCE specific degredation rates and by a lower level of mutual butane-TCE inhibition. A 31 L bioreactor was designed and set up for upscaling the experiment. The second part of the research focused on the biodegradation of 4 polymers, with and with-out chemical pre-treatments: linear low density polyethylene (LLDPE), polyethylene (PP), polystyrene (PS) and polyvinyl chloride (PVC). Initially, the 4 polymers were subjected to different chemical pre-treatments: ozonation and UV/ozonation, in gaseous and aqueous phase. It was found that, for LLDPE and PP, the coupling UV and ozone in gas phase is the most effective way to oxidize the polymers and to generate carbonyl groups on the polymer surface. In further tests, the effect of chemical pretreatment on polyner biodegrability was studied. Gas-phase ozonated and virgin polymers were incubated aerobically with: (a) a pure strain, (b) a mixed culture of bacteria; and (c) a fungal culture, together with saccharose as a co-substrate.

A REGIONAL ASSESSMENT OF GROUNDWATER AVAILABILITY AS CONSTRAINED BY LOCAL HYDROGEOLOGY AND ENVIRONMENTAL LIMITS TO STREAMFLOW DEPLETION

Groundwater pumping from aquifers in hydraulic connection with nearby streams is known to cause adverse impacts by decreasing flows to levels below those necessary to maintain aquatic ecosystems. The recent passage of the Great Lakes--St. Lawrence River Basin Water Resources Compact has brought attention to this issue in the Great Lakes region. In particular, the legislation requires the Great Lakes states to enact measures for limiting water withdrawals that can cause adverse ecosystem impacts. This study explores how both hydrogeologic and environmental flow limitations constrain groundwater availability in the Great Lakes Basin. A methodology for calculating maximum allowable pumping rates is presented. Groundwater availability across the basin is shown to be constrained by a combination of hydrogeologic yield and environmental flow limitations varying over both local and regional scales. The results are sensitive to factors such as pumping time and streamflow depletion limits as well as streambed conductance. Understanding how these restrictions constrain groundwater usage and which hydrogeologic characteristics and spatial variables have the most influence on potential streamflow depletions has important water resources policy and management implications.

Geochemistry and Stable Isotopes of Surface Water and Groundwater in the Continental Pit in Butte, Montana, USA

The Continental porphyry Cu‐Mo mine, located 2 km east of the famous Berkeley Pit lake of Butte, Montana, contains two small lakes that vary in size depending on mining activity. In contrast to the acidic Berkeley Pit lake, the Continental Pit waters have near-neutral pH and relatively low metal concentrations. The main reason is geological: whereas the Berkeley Pit mined highly‐altered granite rich in pyrite with no neutralizing potential, the Continental Pit is mining weakly‐altered granite with lower pyrite concentrations and up to 1‐2% hydrothermal calcite. The purpose of this study was to gather and interpret information that bears on the chemistry of surface water and groundwater in the active Continental Pit. Pre‐existing chemistry data from sampling of the Continental Pit were compiled from the Montana Bureau of Mines and Geology and Montana Department of Environmental Quality records. In addition, in March of 2013, new water samples were collected from the mine’s main dewatering well, the Sarsfield well, and a nearby acidic seep (Pavilion Seep) and analyzed for trace metals and several stable isotopes, including dD and d18O of water, d13C of dissolved inorganic carbon, and d34S of dissolved sulfate. In December 2013, several soil samples were collected from the shore of the frozen pit lake and surrounding area. The soil samples were analyzed using X‐ray diffraction to determine mineral content. Based on Visual Minteq modeling, water in the Continental Pit lake is near equilibrium with a number of carbonate, sulfate, and molybdate minerals, including calcite, dolomite, rhodochrosite (MnCO3), brochantite (CuSO4·3Cu(OH)2), malachite (Cu2CO3(OH)2), hydrozincite (Zn5(CO3)2(OH)6), gypsum, and powellite (CaMoO4). The fact that these minerals are close to equilibrium suggests that they are present on the weathered mine walls and/or in the sediment of the surface water ponds. X‐Ray Diffraction (XRD) analysis of the pond “beach” sample failed to show any discrete metal‐bearing phases. One of the soil samples collected higher in the mine, near an area of active weathering of chalcocite‐rich ore, contained over 50% chalcanthite (CuSO4·5H2O). This water‐soluble copper salt is easily dissolved in water, and is probably a major source of copper to the pond and underlying groundwater system. However, concentrations of copper in the latter are probably controlled by other, less‐soluble minerals, such as brochantite or malachite. Although the acidity of the Pavilion Seep is high (~ 11 meq/L), the flow is much less than the Sarsfield Well at the current time. Thus, the pH, major and minor element chemistry in the Continental Pit lakes are buffered by calcite and other carbonate minerals. For the Continental Pit waters to become acidic, the influx of acidic seepage (e.g., Pavilion Seep) would need to increase substantially over its present volume.

Effects of Coalbed Methane Production on Stream Flow

Coalbed methane production has the potential to reduce instream flows in Powder River Basin streams. Quantifying this effect is difficult, but important, for water users in both Wyoming and Montana. Isotope tracing of coal aquifer groundwater entering the streams can help.

Using 18O/2H, 3H/3He, 85Kr and CFCs to determine mean residence times and water origin in the Grazer and Leibnitzer Feld groundwater bodies (Austria)

Two groundwater bodies, Grazer Feld and Leibnitzer Feld, with surface areas of 166 and 103 km2 respectively are characterised for the first time by measuring the combination of d18O/d2H, 3H/3He, 85Kr, CFC-11, CFC-12 and hydrochemistry in 34 monitoring wells in 2009/2010. The timescales of groundwater recharge have been characterised by 131 d18O measurements of well and surface water sampled on a seasonal basis. Most monitoring wells show a seasonal variation or indicate variable contributions of the main river Mur (0–30%, max. 70%) and/or other rivers having their recharge areas in higher altitudes. Combined d18O/d2H-measurements indicate that 65–75% of groundwater recharge in the unusual wet year of 2009 was from precipitation in the summer based on values from the Graz meteorological station. Monitoring wells downstream of gravel pit lakes show a clear evaporation trend. A boron–nitrate differentiation plot shows more frequent boron-rich water in the more urbanised Grazer Feld and more frequent nitrate-rich water in the more agricultural used Leibnitzer Feld indicating that a some of the nitrate load in the Grazer Feld comes from urban sewer water. Several lumped parameter models based on tritium input data from Graz and monthly data from the river Mur (Spielfeld) since 1977 yield a Mean Residence Time (MRT) for the Mur-water itself between 3 and 4 years in this area. Data from d18O, 3H/3He measurements at the Wagna lysimeter station supports the conclusion that 90% of the groundwaters in the Grazer Feld and 73% in the Leibnitzer Feld have MRTs of <5 years. Only in a few groundwaters were MRTs of 6–10 or 11–25 years as a result of either a long-distance water inflow in the basins or due to longer flow path in somewhat deeper wells (>20 m) with relative thicker unsaturated zones. The young MRT of groundwater from two monitoring wells in the Leibnitzer Feld was confirmed by 85Kr-measurements. Most CFC-11 and CFC-12 concentrations in the groundwater exceed the equilibration concentrations of modern concentrations in water and are therefore unsuitable for dating purposes. An enrichment factor up to 100 compared to atmospheric equilibrium concentrations and the obvious correlation of CFC-12 with SO4, Na, Cl and B in the ground waters of the Grazer Feld suggest that waste water in contact with CFC-containing material above and below ground is the source for the contamination. The dominance of very young groundwater (<5 years) indicates a recent origin of the contamination by nitrate and many other components observed in parts of the groundwater bodies. Rapid measures to reduce those sources are needed to mitigate against further deterioration of these waters.

Modelling susceptibility of grassland soil to macropore flow

Investigating preferential flow, including macropore flow, is crucial to predicting and preventing point sources of contamination in soil, for example in the vicinity of pumping wells. With a view to advancing groundwater protection, this study aimed (i) to quantify the strength of macropore flow in four representative natural grassland soils on the Swiss plateau, and (ii) to define the parameters that significantly control macropore flow in grassland soil. For each soil type we selected three measurement points on which three successive irrigation experiments were carried out, resulting in a total of 36 irrigations. The strength of macropore flow, parameterized as the cumulated water volume flowing from macropores at a depth of 1 m in response to an irrigation of 60 mm h−1 intensity and 1 h duration, was simulated using the dual-permeability MACRO model. The model calibration was based on the key soil parameters and fine measurements of water content at different depths. Modelling results indicate high performance of macropore flow in all investigated soil types except in gleysols. The volume of water that flowed from macropores and was hence expected to reach groundwater varied between 81% and 94% in brown soils, 59% and 67% in para-brown soils, 43% and 56% in acid brown soils, and 22% and 35% in gleysols. These results show that spreading pesticides and herbicides in pumping well protection zones poses a high risk of contamination and must be strictly prohibited. We also found that organic carbon content was not correlated with the strength of macropore flow, probably due to its very weak variation in our study, while saturated water content showed a negative correlation with macropore flow. The correlation between saturated hydraulic conductivity (Ks) and macropore flow was negative as well, but weak. Macropore flow appears to be controlled by the interaction between the bulk density of the uppermost topsoil layer (0–0.10 m) and the macroporosity of the soil below. This interaction also affects the variations in Ks and saturated water content. Further investigations are needed to better understand the combined effect of all these processes including the exchange between micropore and macropore domains.

A method to assess annual average renewable groundwater reserves for large regions in Spain

This paper proposes a method for assessing the groundwater renewable reserves of large regions for an average year, based on the integration of the recession curves for their basins springs or the natural base flow of their rivers. In this method, the hydrodynamic volume (or renewable reserves), were estimated from the baseflow equation. It was assumed that the flow was the same as the natural recharge, and that the recession coefficients were derived by the hydrogeological parameters and geometrical characteristics of aquifers, and adjusted to fit the recession curves at gauging stations. The method was applied to all the aquifers of Spain, which have a total groundwater renewable reserve of 86,895 hm3 four times the mean annual recharge. However, the distribution of these reserves is very variable; 18.6% of the country aquifers contain 94.7% of the entire reserve.

Hidrogeología e hidrodinámica del acuífero de los manantiales de Gormaz y su importancia en el caudal base del río Duero, España = Hydrogeology and hydrodynamic of the Gormaz Springs Aquifer and its importance to the base flow of the Duero River, Spain

Se cuantifican las descargas subterráneas de un acuífero a un río que lo atraviesa utilizando correlaciones estadísticas. El río Duero, España, incrementa su caudal base en varios m3/s, al atravesar unos afloramientos carbonatados mesozoicos en un pequeño tramo de su cabecera; esto es de especial importancia en época de estiaje, cuando la mayor parte del caudal base del río procede de manantiales que allí se sitúan. Dichos afloramientos corresponden a uno de los dos acuíferos calcáreos confinados, que se desarrollan en paralelo y están hidráulicamente desconectados por una capa impermeable, que forman el sistema acuífero de los manantiales de Gormaz. Este sistema se encuentra en estado de régimen natural y está apenas explotado. Se define el modelo conceptual de funcionamiento hidrogeológico, considerando el papel hidrogeológico de la falla de Gormaz, situada en la zona de descarga del sistema. Analizando información geológica antecedente y la geofísica exploratoria realizada, se obtuvo un mejor conocimiento de la geometría y los límites de los acuíferos, definiéndose un sistema acuífero con una zona de recarga en el sur, correspondiente a los afloramientos calcáreos, los cuales se confinan hacia el norte bajo el Terciario, hasta intersecar con la falla normal de Gormaz. El salto de falla genera una barrera para las formaciones permeables situadas al extremo norte (margen derecha del río Duero); a su vez, el plano de falla facilita el ascenso del agua subterránea del sistema acuífero en estudio y pone en conexión hidráulica los dos acuíferos. Se estimaron, además, los parámetros hidráulicos de los acuíferos en los alrededores de la falla. La buena correlación entre los niveles piezométricos y las descargas subterráneas al río Duero han permitido la reconstrucción del hidrograma de los manantiales de Gormaz en el periodo 1992-2006. Se calcula así que la contribución subterránea al río Duero es de 135.9 hm3/año, que supone el 18.9% de la aportación total del río. In a short stretch of its headwaters, the base flow of the River Duero increases by several m3/s as it traverses some Mesozoic carbonate outcrops. This is of special importance during the dry season, when the majority of the base flow of the river proceeds from springs in this reach. The outcrops correspond to one of two confined calcareous aquifers that developed in parallel but which are not hydraulically connected because of an impermeable layer. Together, they constitute the aquifer system of the Gormaz Springs. The system is still in its natural regime and is hardly exploited. This study defines the conceptual model of hydrogeological functioning, taking into consideration the role of the Gormaz Fault, which is situated in the discharge zone of the system. Analysis of both antecedent geological information and geophysical explorations has led to a better understanding of the geometry and boundaries of the aquifers, defining an aquifer system with a recharge zone in the south corresponding to in the calcareous outcrops. These calcareous outcrops are confined to the north below Tertiary formations, as far as their intersection with the normal fault of Gormaz. The throw of the fault forms the barrier of the permeable formations situated in the extreme north (right bank of the River Duero). In turn, the fault plane facilitates the upflow of groundwater from the aquifer system and creates hydraulic connection between the two aquifers. In addition, the study estimated the hydraulic parameters of the aquifer around the fault. The close correlation between piezometric levels and the groundwater discharges to the River Duero has enabled the reconstruction of the hydrogram of Gormaz springs over the period 1992-2006. By this means, it is calculated that the groundwater contribution to the River Duero is 135.9 hm3/year, or 18.9% of the total river inflow.

Guidelines for the design of an environmental flow regime program at the regional scale: Application of the ELOHA framework in the Ebro River basin

La gestión de los recursos hídricos se convierte en un reto del presente y del futuro frente a un panorama de continuo incremento de la demanda de agua debido al crecimiento de la población, el crecimiento del desarrollo económico y los posibles efectos del calentamiento global. La política hidráulica desde los años 60 en España se ha centrado en la construcción de infraestructuras que han producido graves alteraciones en el régimen natural de los ríos. Estas alteraciones han provocado y acrecentado los impactos sobre los ecosistemas fluviales y ribereños. Desde los años 90, sin embargo, ha aumentado el interés de la sociedad para conservar estos ecosistemas. El concepto de caudales ambientales consiste en un régimen de caudales que simula las características principales del régimen natural. Los caudales ambientales están diseñados para conservar la estructura y funcionalidad de los ecosistemas asociados al régimen fluvial, bajo la hipótesis de que los elementos que conforman estos ecosistemas están profundamente adaptados al régimen natural de caudales, y que cualquier alteración del régimen natural puede provocar graves daños a todo el sistema. El método ELOHA (Ecological Limits of Hydrological Alteration) tiene como finalidad identificar las componentes del régimen natural de caudales que son clave para mantener el equilibrio de los ecosistemas asociados, y estimar los límites máximos de alteración de estas componentes para garantizar su buen estado. Esta tesis presenta la aplicación del método ELOHA en la cuenca del Ebro. La cuenca del Ebro está profundamente regulada e intervenida por el hombre, y sólo las cabeceras de los principales afluentes del Ebro gozan todavía de un régimen total o cuasi natural. La tesis se estructura en seis capítulos que desarrollan las diferentes partes del método. El primer capítulo explica cómo se originó el concepto “caudales ambientales” y en qué consiste el método ELOHA. El segundo capítulo describe el área de estudio. El tercer capítulo realiza una clasificación de los regímenes naturales de la cuenca (RNC) del Ebro, basada en series de datos de caudal mínimamente alterado y usando exclusivamente parámetros hidrológicos. Se identificaron seis tipos diferentes de régimen natural: pluvial mediterráneo, nivo-pluvial, pluvial mediterréaneo con una fuerte componente del caudal base, pluvial oceánico, pluvio-nival oceánico y Mediterráneo. En el cuarto capítulo se realiza una regionalización a toda la cuenca del Ebro de los seis RNC encontrados en la cueca. Mediante parámetros climáticos y fisiográficos se extrapola la información del tipo de RNC a puntos donde no existen datos de caudal inalterado. El patrón geográfico de los tipos de régimen fluvial obtenido con la regionalización resultó ser coincidente con el patrón obtenido a través de la clasificación hidrológica. El quinto capítulo presenta la validación biológica de los procesos de clasificación anteriores: clasificación hidrológica y regionalización. La validación biológica de los tipos de regímenes fluviales es imprescindible, puesto que los diferentes tipos de régimen fluvial van a servir de unidades de gestión para favorecer el mantenimiento de los ecosistemas fluviales. Se encontraron diferencias significativas entre comunidades biológicas en cinco de los seis tipos de RNC encontrados en la cuenca. Finalmente, en el sexto capítulo se estudian las relaciones hidro-ecológicas existentes en tres de los seis tipos de régimen fluvial encontrados en la cuenca del Ebro. Mediante la construcción de curvas hidro-ecológicas a lo largo de un gradiente de alteración hidrológica, se pueden sugerir los límites de alteración hidrológica (ELOHAs) para garantizar el buen estado ecológico en cada uno de los tipos fluviales estudiados. Se establecieron ELOHAs en tres de los seis tipos de RNC de la cuenca del Ebro Esta tesis, además, pone en evidencia la falta de datos biológicos asociados a registros de caudal. Para llevar a cabo la implantación de un régimen de caudales ambientales en la cuenca, la ubicación de los puntos de muestreo biológico cercanos a estaciones de aforo es imprescindible para poder extraer relaciones causa-efecto de la gestión hidrológica sobre los ecosistemas dependientes. ABSTRACT In view of a growing freshwater demand because of population raising, improvement of economies and the potential effects of climate change, water resources management has become a challenge for present and future societies. Water policies in Spain have been focused from the 60’s on constructing hydraulic infrastructures, in order to dampen flow variability and granting water availability along the year. Consequently, natural flow regimes have been deeply altered and so the depending habitats and its ecosystems. However, an increasing acknowledgment of societies for preserving healthy freshwater ecosystems started in the 90’s and agreed that to maintain healthy freshwater ecosystems, it was necessary to set environmental flow regimes based on the natural flow variability. The Natural Flow Regime paradigm (Richter et al. 1996, Poff et al. 1997) bases on the hypothesis that freshwater ecosystems are made up by elements adapted to natural flow conditions, and any change on these conditions can provoke deep impacts on the whole system. Environmental flow regime concept consists in designing a flow regime that emulates natural flow characteristics, so that ecosystem structure, functions and services are maintained. ELOHA framework (Ecological Limits of Hydrological Alteration) aims to identify key features of the natural flow regime (NFR) that are needed to maintain and preserve healthy freshwater and riparian ecosystems. Moreover, ELOHA framework aims to quantify thresholds of alteration of these flow features according to ecological impacts. This thesis describes the application of the ELOHA framework in the Ebro River Basin. The Ebro River basin is the second largest basin in Spain and it is highly regulated for human demands. Only the Ebro headwaters tributaries still have completely unimpaired flow regime. The thesis has six chapters and the process is described step by step. The first chapter makes an introduction to the origin of the environmental flow concept and the necessity to come up. The second chapter shows a description of the study area. The third chapter develops a classification of NFRs in the basin based on natural flow data and using exclusively hydrological parameters. Six NFRs were found in the basin: continental Mediterranean-pluvial, nivo-pluvial, continental Mediterranean pluvial (with groundwater-dominated flow pattern), pluvio-oceanic, pluvio-nival-oceanic and Mediterranean. The fourth chapter develops a regionalization of the six NFR types across the basin by using climatic and physiographic variables. The geographical pattern obtained from the regionalization process was consistent with the pattern obtained with the hydrologic classification. The fifth chapter performs a biological validation of both classifications, obtained from the hydrologic classification and the posterior extrapolation. When the aim of flow classification is managing water resources according to ecosystem requirements, a validation based on biological data is compulsory. We found significant differences in reference macroinvertebrate communities between five over the six NFR types identified in the Ebro River basin. Finally, in the sixth chapter we explored the existence of significant and explicative flow alteration-ecological response relationships (FA-E curves) within NFR types in the Ebro River basin. The aim of these curves is to find out thresholds of hydrological alteration (ELOHAs), in order to preserve healthy freshwater ecosystem. We set ELOHA values in three NFR types identified in the Ebro River basin. During the development of this thesis, an inadequate biological monitoring in the Ebro River basin was identified. The design and establishment of appropriate monitoring arrangements is a critical final step in the assessment and implementation of environmental flows. Cause-effect relationships between hydrology and macroinvertebrate community condition are the principal data that sustain FA-E curves. Therefore, both data sites must be closely located, so that the effects of external factors are minimized. The scarce hydro-biological pairs of data available in the basin prevented us to apply the ELOHA method at all NFR types.

THE TRANSPORT OF HEAT BY FLOWING GROUNDWATER IN A DISCRETE FRACTURE

In typical theoretical or experimental studies of heat migration in discrete fractures, conduction and thermal dispersion are commonly neglected from the fracture heat transport equation, assuming heat conduction into the matrix is predominant. In this study analytical and numerical models are used to investigate the significance of conduction and thermal dispersion in the plane of the fracture for a point and line sources geometries. The analytical models account for advective, conductive and dispersive heat transport in both the longitudinal and transverse directions in the fracture. The heat transport in the fracture is coupled with a matrix equation in which heat is conducted in the direction perpendicular to the fracture. In the numerical model, the governing heat transport processes are the same as the analytical models; however, the matrix conduction is considered in both longitudinal and transverse directions. Firstly, we demonstrate that longitudinal conduction and dispersion are critical processes that affect heat transport in fractured rock environments, especially for small apertures (eg. 100 μm or less), high flow rate conditions (eg. velocity greater than 50 m/day) and early time (eg. less than 10 days). Secondly, transverse thermal dispersion in the fracture plane is also observed to be an important transport process leading to retardation of the migrating heat front particularly at late time (eg. after 40 days of hot water injection). Solutions which neglect dispersion in the transverse direction underestimate the locations of heat fronts at late time. Finally, this study also suggests that the geometry of the heat sources has significant effects on the heat transport in the system. For example, the effects of dispersion in the fracture are observed to decrease when the width of the heat source expands.

Radial flow behavior of artificial recharge from surface cavities,

Bibliography: p. 53.