Haja-asutusalueen keskijänniteverkon kaapeloinnin ja automaation suunnittelumetodiikka

Tässä diplomityössä tutkitaan erilaisia keskijänniteverkon kehittämismenetelmiä sekä suunnittelua haja-asutusalueelle. Suunnittelumetodiikan perustana on vertailla sähköverkon käyttövarmuuden tunnuslukujen sekä kokonaiskustannusten kehittymistä erilaisilla investointiratkaisuilla. Lähemmässä tarkastelussa ovat erilaiset kaapelointimenetelmät sekä automaatiolaitteet kuten maastoon sijoitettavat katkaisijat sekä kauko-ohjattavat erottimet. Kehittämisratkaisujen vertailemiseksi sähköverkosta muodostetaan laskentaa varten malli, jonka avulla on mahdollista tarkastella mm. käyttövarmuuden tunnuslukujen sekä verkon kustannusten kehittymistä. Verkon kustannuksissa otetaan huomioon investointikustannukset, käyttö- ja kunnossapitokustannukset, viankorjauskustannukset sekä keskeytyskustannukset. Keskeytysten laskentaa varten toteutetaan erilliset laskentalohkot, jotta keskeytyskustannukset saadaan mallinnettua tarkasti. Kaapelointistrategia-analyysissä vertaillaan kaapeloinnin erilaisia toteuttamisperiaatteita. Erilaisia tutkittavia kaapelointimenetelmiä ovat vyörytysmenetelmä, vikaherkimpien kohteiden uusinta, vanhimpien kohteiden uusinta, täydellinen kaapelointi sekä optimiverkostoratkaisu, jossa on hyödynnetty keskijännitejohtojen kaapeloinnin lisäksi mm. automaatioratkaisuja ja 1000 V tekniikkaa. Kaapelointimenetelmiä vertailtaessa on havaittu, että vikaherkimmistä kohteista aloitettava saneeraus tuottaa parhaimman tuloksen, jos optimiratkaisua ei oteta huomioon.

Grounding in a wind power application

The subject of this master’s thesis is to research grounding in a particular wind power application. The aim is to define how the grounding from different points effects to the function of the whole system. The investigated subjects are generator voltage spikes, ground currents and system fault situations. The first part of this thesis represents power electronics, which is commonly used in wind power systems. The second part concentrates more to the grounding, electrical safety demands and potential fault situations. The object of the simulations is to investigate voltage spikes and fault situations. Measurements will be made with small-scale setup and in the last part simulation and measurement results are compared to each other and to a full-scale system.

Microcontroller-based interface circuit for inductive sensors

This work proposes a fully-digital interface circuit for the measurement of inductive sensors using a low-cost microcontroller (µC) and without any intermediate active circuit. Apart from the µC and the sensor, the circuit just requires an external resistor and a reference inductance so that two RL circuits with a high-pass filter (HPF) topology are formed. The µC appropriately excites such RL circuits in order to measure the discharging time of the voltage across each inductance (i.e. sensing and reference) and then it uses such discharging times to estimate the sensor inductance. Experimental tests using a commercial µC show a non-linearity error (NLE) lower than 0.5%FSS (Full-Scale Span) when measuring inductances from 1 mH to 10 mH, and from 10 mH to 100 mH.

The factorial structure of the 41-item version of the Screen for Child Anxiety Related Emotional Disorders (SCARED) in a Spanish population of 8 to 12 years-old

On this instrumental study we intend to analyse the factorial structure of the Screen for Child Anxiety Related Emotional Disorders (SCARED) in a Spanish sample using exploratory and confirmatory factorial analysis. As a second objective we intend to develop a short form of it for rapid screening and, finally, to analyze the reliabilities of both questionnaires. The SCARED was administered to a community sample of 1,508 children aged between 8 and 12 years. The sample was randomly split using half for the exploratory analysis and the other half for the confirmatory study. Furthermore a reduced version of the SCARED was developed using the SchmidLeiman procedure. Exploratory Factor Analysis yielded a four factor structure comprised of Somatic/panic, Generalized anxiety, Separation anxiety and Social phobia factors This structure was confirmed using Confirmatory Factor Analysis. The four factors, the full scale and the short scale showed good reliabilities. The results obtained seem to indicate that the Spanish version of the SCARED has good internal consistency, and along with other recent results, has a structure of four related factors that replicates the dimensions proposed for anxiety disorders by the DSM-IV-TR

Täystehokonvertterin tehohäviöt ja hyötysuhde

Diplomityössä perehdytään tuuliturbineissa käytettyjen täystehokonvertterien tehohäviöihin ja hyötysuhteeseen. Täystehokonvertterissa generaattorin tuottama sähköteho tasasuunnataan hyvällä hyötysuhteella aktiivisella geenraattorisillalla konvertterin välipiiriin ja edelleen vaihtosuunnataan aktiivisella verkkovaihtosuuntaajasillalla siirtoverkkoon. Työn tarkoituksena on antaa yleiskuva tehohäviöiden jakautumisesta ja yksinkertaistaa niiden laskentaa. Häviömekanismit ja häviöiden määräytyminen esitellään pääkomponenttitasolla. Tehohäviöiden osalta keskitytään erityisesti muuntajateräksestä valmistettujen sinisuotimien ja du/dt-suotimien rautahäviöihin. Ongelmana rautahäviöiden määrittämisessä on korkeilla taajuuksilla tapahtuvat häviöt, joiden laskentaan ei ole yleensä saatavilla tarvittavia materiaaliparametrejä. Tehohäviöiden laskentaa varten toteutettu laskentasovellus on esitelty periaatteellisina vuokaavioina ja sovelluksella saatavia tuloksia on esitetty ja vertailtu mitattuihin tuloksiin.

Multilevel converter modulation: implementation and analysis

Multilevel converters provide an attractive solution to bring the benefits of speed-controlled rotational movement to high-power applications. Therefore, multilevel inverters have attracted wide interest in both the academic community and in the industry for the past two decades. In this doctoral thesis, modulation methods suitable especially for series connected H-bridge multilevel inverters are discussed. A concept of duty cycle modulation is presented and its modification is proposed. These methods are compared with other well-known modulation schemes, such as space-vector pulse width modulation and carrier-based modulation schemes. The advantage of the modified duty-cycle modulation is its algorithmic simplicity. A similar mathematical formulation for the original duty cycle modulation is proposed. The modified duty cycle modulation is shown to produce well-formed phase-to-neutral voltages that have lower total harmonic distortion than the space-vector pulse width modulation and the duty cycle modulation. The space-vector-based solution and the duty cycle modulation, on the other hand, result in a better-quality line-to-line voltage and current waveform. The voltage of the DC links in the modules of the series-connected H-bridge inverter are shown to fluctuate while they are under load. The fluctuation causes inaccuracies in the voltage production, which may result in a failure of the flux estimator in the controller. An extension for upper-level modulation schemes, which changes the switching instants of the inverter so that the output voltage meets the reference voltage accurately regardless of the DC link voltages, is proposed. The method is shown to reduce the error to a very low level when a sufficient switching frequency is used. An appropriate way to organize the switching instants of the multilevel inverter is to make only one-level steps at a time. This causes restrictions on the dynamical features of the modulation schemes. The produced voltage vector cannot be rotated several tens of degrees in a single switching period without violating the above-mentioned one-level-step rule. The dynamical capabilities of multilevel inverters are analyzed in this doctoral thesis, and it is shown that the multilevel inverters are capable of operating even in dynamically demanding metal industry applications. In addition to the discussion on modulation schemes, an overvoltage in multilevel converter drives caused by cable reflection is addressed. The voltage reflection phenomenon in drives with long feeder cables causes premature insulation deterioration and also affects the commonmode voltage, which is one of the main reasons for bearing currents. Bearing currents, on the other hand, cause fluting in the bearings, which results in premature bearing failure. The reflection phenomenon is traditionally prevented by filtering, but in this thesis, a modulationbased filterless method to mitigate the overvoltage in multilevel drives is proposed. Moreover, the mitigation method can be implemented as an extension for upper-level modulation schemes. The method exploits the oscillations caused by two consecutive voltage edges so that the sum of the oscillations results in a mitigated peak of the overvoltage. The applicability of the method is verified by simulations together with experiments with a full-scale prototype.

Lujasta rakenneteräksestä tehdyn rakenteen vikasietoisuuden määritys

Tässä työssä tutkittiin Ruukin valmistamista lujista Optim 700 MC Plus sekä Optim 700 QL teräksistä tehtyjen hitsattujen palkkirakenteiden vikasietoisuutta sekä murtumiskäyttäytymistä laboratoriossa suoritettujen täyden mittakaavan kokeiden avulla. Koerakenteet suunniteltiin siten, että rakenteen kylmämuovauksen sekä hitsauksen vaikutukset yhdessä rakenteen geometrian vaikutuksen kanssa heikentävät rakenteen murtumissitkeyttä rakenteeseen tehdyn teräväkärkisen alkusärön tasossa. Suunnitellussa koesarjassa varioidaan testauslämpötilan lisäksi hitsauksen lämmöntuontia sekä koerakenteeseen tehtävän alkusärön kokoa. Tässä työssä tavoitteena oli yleisesti esittää menettely hitsatun säröllisen teräsrakenteen kestävyyden arviointia varten. Optim 700 MC Plus teräksestä tehdyn koerakenteen käyttäytymistä tutkittiin laskennallisesti murtumismekaniikan avulla. Laadittujen FEM - mallien avulla laskettiin rakenteen murtumisparametrien arvot kummallekin tutkittavalle teräkselle. Optim 700 MC Plus materiaalista valmistetuille koerakenteen säröalueen rakennedetaljia vastaavalle koekappaleille suoritettiin murtumissitkeyskokeita. Murtumissitkeyskokeista saatujen tulosten avulla pystyttiin kuvaamaan täyden mittakaavan koerakenteessa olevan särön murtumiskäyttäytymistä mitoitusmenetelmissä. Koerakenteelle laskettiin tässä työssä kriittisen särökoon ja sitä vastaavan kuorman arvot perustuen rakenteen oletettuun hauraaseen, epästabiiliin sitkeään sekä plastiseen murtumiskäyttäytymiseen. Tässä työssä testattiin molemmista tutkittavista materiaaleista valmistetut täyden mittakaavan koerakenteet -40 °C lämpötilassa. Molemmat testatut rakenteet käyttäytyvät mitattujen siirtymätulosten perusteella melko hauraasti. Optim 700 MC Plus materiaalille saatujen laskentatulosten voidaan todeta testatun koekappaleen perusteella soveltuvan hauraasti käyttäytyvän rakenteen mitoitukseen.

Corrosion behaviour of boiler tube materials during combustion of fuels containing Zn and Pb

Många förbränningsanläggningar som bränner utmanande bränslen såsom restfraktioner och avfall råkar ut för problem med ökad korrosion på överhettare och/eller vattenväggar pga. komponenter i bränslena som är korrosiva. För att minimera problemen i avfallseldade pannor hålls ångparametrarna på en relativt låg nivå, vilket drastiskt minskar energiproduktionen. Beläggningarna i avfallseldade pannor består till största delen av element som är förknippade med högtemperaturkorrosion: Cl, S, alkalimetaller, främst K och Na, och tungmetaller som Pb och Zn, och det finns också indikationer av Br-förekomst. Det låga ångtrycket i avfallseldade pannor påverkar också stålrörens temperatur i pannväggarna i eldstaden. I dagens läge hålls temperaturen normalt vid 300-400 °C. Alkalikloridorsakad (KCl, NaCl) högtemperaturkorrosion har inte rapporterats vara relevant vid såpass låga temperaturer, men närvaro av Zn- och Pb-komponenter i beläggningarna har påvisats förorsaka ökad korrosion redan vid 300-400 °C. Vid förbränning kan Zn och Pb reagera med S och Cl och bilda klorider och sulfater i rökgaserna. Dessa tungmetallföreningar är speciellt problematiska pga. de bildar lågsmältande saltblandningar. Dessa lågsmältande gasformiga eller fasta föreningar följer rökgasen och kan sedan fastna eller kondensera på kallare ytor på pannväggar eller överhettare för att sedan bilda aggressiva beläggningar. Tungmetallrika (Pb, Zn) klorider och sulfater ökar risken för korrosion, och effekten förstärks ytterligare vid närvaro av smälta. Motivet med den här studien var att få en bättre insikt i högtemperaturkorrosion förorsakad av Zn och Pb, samt att undersöka och prediktera beteendet och motståndskraften hos några stålkvaliteter som används i överhettare och pannväggar i tungmetallrika förhållanden och höga materialtemperaturer. Omfattande laboratorie-, småskale- och fullskaletest utfördes. Resultaten kan direkt utnyttjas i praktiska applikationer, t.ex. vid materialval, eller vid utveckling av korrosionsmotverkande verktyg för att hitta initierande faktorer och förstå deras effekt på högtemperaturkorrosion.

Characterisation of waste for combustion : with special reference to the role of zinc

Waste combustion has gone from being a volume reducing discarding-method to an energy recovery process for unwanted material that cannot be reused or recycled. Different fractions of waste are used as fuel today, such as; municipal solid waste, refuse derived fuel, and solid recovered fuel. Furthermore, industrial waste, normally a mixture between commercial waste and building and demolition waste, is common, either as separate fuels or mixed with, for example, municipal solid waste. Compared to fossil or biomass fuels, waste mixtures are extremely heterogeneous, making it a complicated fuel. Differences in calorific values, ash content, moisture content, and changing levels of elements, such as Cl and alkali metals, are common in waste fuel. Moreover, waste contains much higher levels of troublesome trace elements, such as Zn, which is thought to accelerate a corrosion process. Varying fuel quality can be strenuous on the boiler system and may cause fouling and corrosion of heat exchanger surfaces. This thesis examines waste fuels and waste combustion from different angles, with the objective of giving a better understanding of waste as an important fuel in today’s fuel economy. Several chemical characterisation campaigns of waste fuels over longer time periods (10-12 months) was used to determine the fossil content of Swedish waste fuels, to investigate possible seasonal variations, and to study the presence of Zn in waste. Data from the characterisation campaigns were used for thermodynamic equilibrium calculations to follow trends and determine the effect of changing concentrations of various elements. The thesis also includes a study of the thermal behaviour of Zn and a full—scale study of how the bed temperature affects the volatilisation of alkali metals and Zn from the fuel. As mixed waste fuel contains considerable amounts of fresh biomass, such as wood, food waste, paper etc. it would be wrong to classify it as a fossil fuel. When Sweden introduced waste combustion as a part of the European Union emission trading system in the beginning of 2013 there was a need for combustion plants to find a usable and reliable method to determine the fossil content. Four different methods were studied in full-scale of seven combustion plants; 14Canalysis of solid waste, 14C-analysis of flue gas, sorting analysis followed by calculations, and a patented balance method that is using a software program to calculate the fossil content based on parameters from the plant. The study showed that approximately one third of the coal in Swedish waste mixtures has fossil origins and presented the plants with information about the four different methods and their advantages and disadvantages. Characterisation campaigns also showed that industrial waste contain higher levels of trace elements, such as Zn. The content of Zn in Swedish waste fuels was determined to be approximately 800 mg kg-1 on average, based on 42 samples of solid waste from seven different plants with varying mixtures between municipal solid waste and industrial waste. A review study of the occurrence of Zn in fuels confirmed that the highest amounts of Zn are present in waste fuels rather than in fossil or biomass fuels. In tires, Zn is used as a vulcanizing agent and can reach concentration values of 9600-16800 mg kg-1. Waste Electrical and Electronic Equipment is the second Zn-richest fuel and even though on average Zn content is around 4000 mg kg-1, the values of over 19000 mg kg-1 were also reported. The increased amounts of Zn, 3000-4000 mg kg-1, are also found in municipal solid waste, sludge with over 2000 mg kg-1 on average (some exceptions up to 49000 mg kg-1), and other waste derived fuels (over 1000 mg kg-1). Zn is also found in fossil fuels. In coal, the average level of Zn is 100 mg kg-1, the higher amount of Zn was only reported for oil shale with values between 20-2680 mg kg-1. The content of Zn in biomass is basically determined by its natural occurrence and it is typically 10-100 mg kg-1. The thermal behaviour of Zn is of importance to understand the possible reactions taking place in the boiler. By using thermal analysis three common Zn-compounds were studied (ZnCl2, ZnSO4, and ZnO) and compared to phase diagrams produced with thermodynamic equilibrium calculations. The results of the study suggest that ZnCl2(s/l) cannot exist readily in the boiler due to its volatility at high temperatures and its conversion to ZnO in oxidising conditions. Also, ZnSO4 decomposes around 680°C, while ZnO is relatively stable in the temperature range prevailing in the boiler. Furthermore, by exposing ZnO to HCl in a hot environment (240-330°C) it was shown that chlorination of ZnO with HCl gas is possible. Waste fuel containing high levels of elements known to be corrosive, for example, Na and K in combination with Cl, and also significant amounts of trace elements, such as Zn, are demanding on the whole boiler system. A full-scale study of how the volatilisation of Na, K, and Zn is affected by the bed temperature in a fluidised bed boiler was performed parallel with a lab-scale study with the same conditions. The study showed that the fouling rate on deposit probes were decreased by 20 % when the bed temperature was decreased from 870°C to below 720°C. In addition, the lab-scale experiments clearly indicated that the amount of alkali metals and Zn volatilised depends on the reactor temperature.

Fate of fuel-bound nitrogen and sulfur in biomass-fired Industrial boilers

Användning av biomassa som energikälla för produktion av el och värme är ett sätt att minska beroendet av fossila bränslen och höja självförsörjningen av energi. Fossila bränslen är den främsta källan till koldioxid utsläpp förorsakad av människan. Biomassa, å andra sidan, betraktas som en koldioxidneutral energikälla. Svavlet och kvävet i biomassan bildar dock föroreningar såsom kväveoxider (NOX) och svaveldioxid (SO2), som bidrar till försurning av mark och sjöar. Svavlet i bränslet kan även både förorsaka och förhindra korrosion i en förbränningsanläggning, beroende på förbränningen och bränslet. Huvudsyftet med detta arbete var att få en bättre förståelse om hur utsläppen av NOX och SO2 bildas från bränslebundet kväve och svavel vid förbränning av olika biobränslen. Mätkampanjer i fullskaliga förbränningsanläggningar utfördes, där gassammansättningen mättes i eldstaden och rökgasen. Förståelsen om gaskemin i eldstaden är viktig, för att möjliggöra utvecklandet av renare och effektivare förbränningsanläggningar. Ett annat syfte med arbetet var att klargöra om sulfatering av askkomponenter vid förbränning av biobränslen med olika askegenskaper. Alkaliklorider som bildas vid biomassaförbränning kan orsaka korrosion av värmeöverföringsytor. Svavlet i bränslet visade sig ha en viktig roll i att sulfatera alkaliklorider till mindre korrosiva alkalisulfater. Närvaron av gasformig svavelsyra i rökgaskanalen av förbränningsanläggningar studerades även. Kondensering av svavelsyra leder till korrosion av rökgaskanalen och dess delar. Om svavelsyrakoncentrationen i rökgasen är känd, kan daggpunktstemperaturen beräknas och kondensering av svavelsyra förhindras. I arbetet utvecklades en mätmetod för att mäta låga koncentrationer av gasformig svavelsyra i rökgaser. Denna metod användes för att undersöka risken av lågtemperaturkorrosion orsakad av svavelsyra i förbränningsanläggningar. ------------------------------------------------------------------------------------------------------------ Käyttämällä biomassaa energianlähteenä voidaan vähentää sähkön- ja lämmöntuotannon riippuvuutta fossiilisiin polttoaineisiin. Biomassan käytöllä voidaan myös lisätä energiantuotannon omavaraisuutta. Fossiiliset polttoaineet ovat pääasiallinen syy ihmisen aiheuttamiin hiilidioksidipäästöihin. Biomassa sen sijaan luetaan hiilidioksidineutraaleihin energianlähteisiin. Biopolttoaineiden käytössä tosin vapautuu typpi- ja rikkioksideja, jotka edesauttavat maaperän ja merien happamoitumista. Lisäksi biopolttoaineen rikki voi sekä vähentää että aiheuttaa laitteiden korroosiota energiantuotannossa riippuen biopolttoaineesta ja palamisesta. Tämän työn päätavoitteena oli selvittää mitä biopolttoaineeseen sitoutuneelle typelle ja rikille tapahtuu teollisissa polttolaitoksissa. Kyseisten oksidien muodostumista tutkittiin polttamalla eri biomassoja polttolaitoksissa. Tutkimukset toteutettiin mittauskampanjoilla useissa polttolaitoksissa. Kaasujen koostumusta mitattiin sekä tulipesässä, että savukaasuista. Kaasujen koostumus varsinkin tulipesässä on tärkeää, jotta tulevaisuudessa voidaan rakentaa puhtaampia ja tehokkaampia polttolaitoksia. Työn toisena tavoitteena oli selvittää biomassan polton yhteydessä tapahtuvaa tuhkan sulfatoitumista. Alkalikloridit, joita muodostuu biomassan poltossa, voivat aiheuttaa lämmönsiirtopintojen korroosiota. Rikki osoittautui tärkeäksi osaksi prosessia, jossa korroosiota aiheuttavat alkalikloridit sulfatoituivat vähemmän korrosoiviksi alkalisulfaateiksi. Myös kaasumaisen rikkihapon läsnäoloa savukaasuissa tutkittiin. On todettu, että kaasumuotoinen rikkihappo johtaa korroosioon savukaasukanavan kylmässä päässä ja sen eri osissa rikkihapon tiivistyessä lämpötilan laskiessa. Mikäli rikkihapon pitoisuus savukaasussa tiedetään, sen kastepiste voidaan laskea ja tiivistyminen estää. Tässä työssä kehitettiin mittausmenetelmä rikkihapon alhaisten pitoisuuksien mittaamiseen. Menetelmää hyödynnettiin polttolaitoksissa, joissa tutkittiin rikkihapon tiivistymisestä johtuvaa korroosiota.

Capital investments planning and life cycle simulations for the new valves manufacturing facility in Russia

The focus of the research is on the derivation of the valid and reliable performance results regarding establishment and launching of the new full-scale industrial facility, considering the overall current conditions for the project realization in and out of Russia. The study demonstrates the process of the new facility concept development, with following perfor-mance calculation, comparative analyzes conduction, life-cycle simulations, performance indicators derivation and project`s sustainability evaluation. To unite and process the entire input parameters complexity, regards the interlacing between the project`s internal technical and commercial sides on the one hand, and consider all the specifics of the Russian conditions for doing business on the other hand, was developed the unique model for the project`s performance calculation, simulations and results representation. The complete research incorporates all corresponding data to substantiate the assigned facility`s design, sizing and output capacity for high quality and cost efficient ferrous pipe-line accessories manufacturing, as well as, demonstrates that this project could be suc-cessfully realized in current conditions in Russia and highlights the room for significant performance and sustainability improvements based on the indexes of the derived KPIs.

Kartoitus Kaakkois-Suomen jätelietteistä, lietteen tuottajista ja käsittelymenetelmistä

In this thesis the sludge of Southeastern-Finland, the companies which produce sludge and the current methods and those still in development have been surveyed. 85 % of the waste sludge from industry comes from forest industries. The sludge from municipal waste water treatment plants is mostly used as a raw material for bioplants. The sludge from forest industry is mostly incinerated. New circulation methods increase the recycling value of the waste by creating new products but they still lack a full-scale plant. The political pressure from Europe and the politics driven by the government of Finland will drive circular economy forward and thus uplifting the processing options of waste slurries. This work is divided in two parts, first contains the survey and the second contains the experimental part and the operational methods based on the survey. In the experimental part wet hard sheet waste sludge was de-watered with shaking filter and the applications for waste sludge from cellulose factory were considered. The results are, that the wet hard sheet waste sludge can be dewatered to high enough total solids content for the inteded use. Also, the cellulose waste sludge has too high Cd content in almost all of the batches to be used as a land improment.

Agrarian revolution in Central America : a comparison of Nicaragua and Honduras using Jeffery Paige's theory of Agrarian revolution

ABSTRACT In 1979 Nicaragua, under the Sandinistas, experienced a genuine, socialist, full scale, agrarian revolution. This thesis examines whether Jeffery Paige's theory of agrarian revolutions would have been successful in predicting this revolution and ln predicting non-revolution in the neighboring country of Honduras. The thesis begins by setting Paige's theory in the tradition of radical theories of revolution. It then derives four propositions from Paige's theory which suggest the patterns of export crops, land tenure changes and class configurations which are necessary for an agrarian and socialist revolution. These propositions are tested against evidence from the twentieth century histories of economic, social and political change in Nicaragua and Honduras. The thesis concludes that Paige's theory does help to explain the occurrence of agrarian revolution in Nicaragua and non-revolution in Honduras. A fifth proposition derived from Paige's theory proved less useful in explaining the specific areas within Nicaragua that were most receptive to Sandinista revolutionary activity.

Niagara Symphony Orchestra fonds, 1926, 1948-1998, n.d.

In 1948, The St. Catharines Civic Orchestra was founded by Jan Wolanek who was also the first conductor. Initially, this was a community orchestra and in 1963 its governing body assumed the name St. Catharines Symphony Association. In 1978 the name was again changed to The Niagara Symphony Association to reflect regional responsibilities. Wally Laughton was named Assistant Conductor in 1952/53. R.C. Clarke took over the orchestra for an interim period after Wolanek left in 1957. In 1958 Leonard Pearlman became the Music Director. It was under his direction that the Niagara Symphony Chorus came into existence in 1963. Milton Barnes succeeded Pearlman in 1964 and he was responsible for directing the symphony’s first opera production. He also made a concerted effort to attract younger people to symphonic music. In 1972 Leonard Atherton became the Music Director. He started the Cantata Choir and the Madrigal Singers. It was under his tenure that the orchestra became professional. When Atherton left in 1980, there were three seasons of guest conductors, the most notable of these conductors was Uri Mayer. In 1981 James Vincent Fusco was appointed as composer in residence and in 1983 Ermanno Florio became the Music Director. He retained this position until 1995 when Michael Reason took over. Daniel Swift was appointed as Music Director and Conductor in 1999 and the Niagara Symphony Orchestra became the orchestr in residence at Brock University. Laura Thomas was appointed as Associate Conductor 1n 2004. Daniel Swift’s resignation in 2008 began a search for a new Music Director. Bradley Thachuck was appointed as Music Director Designate and Principal Conductor in 2010. The orchestra is a fully professional, charitable institution with 52 members.The orchestra has also been led by Victor Feldbrill and Howard Cable. A junior symphony was first formed under Leonard Pearlman in 1960/61, but it wasn’t until 1965 that The St. Catharines Youth Orchestra was founded. The orchestra has consistently been an award winner in music festivals. The musicians range in age from 12 to 18 years. The highlight of the 1973-74 season was the orchestra’s participation in the first Canadian Festival of Youth Orchestras at The Banff School of Fine Arts. The St. Catharines Youth Orchestra has evolved from the St. Catharines School String and Brass Ensembles to a full scale symphony under the direction of conductor Paul van Dongen. In 1974 the Symphony House music program came into existence. It was 1976 when Richard Grymonpre was hired as the principal violinist of the St. Catharines Symphony Orchestra and conductor of the St. Catharines Youth Orchestra. Tak Ng Lai took over the position as conductor in 1978. Laura Thomas is currently the Music Director of The Niagara Youth Orchestra. Source: Niagara Symphony, Orchestra in Residence, Brock University website and notes from Niagara Symphony files

Les gladiateurs grecs en Asie Mineure durant le Haut-Empire romain à Éphèse, Aphrodisias, Attaleia et Side.

Entièrement réalisé grâce au programme LaTeX (http://www.latex-project.org/)