680 resultados para Flames Premixed Laminar
Resumo:
The twenty-first century Iowa State Capitol contains state-of-the-art fire protection. Sprinklers and smoke detectors are located in every room and all public hallways are equipped with nearby hydrants. The Des Moines Fire Department is able to fight fires at nearly any height. However, on Monday morning, January 4, 1904, the circumstances were much different. By the beginning of 1904, the Capitol Improvement Commission had been working in the Capitol for about two years. The commissioners were in charge of decorating the public areas of the building, installing the artwork in the public areas, installing a new copper roof, re-gilding the dome, replacing windows, and connecting electrical lines throughout. Electrician H. Frazer had been working that morning in Committee Room Number Five behind the House Chamber, drilling into the walls to run electrical wires and using a candle to light his way. The investigating committee determined that Frazer had left his work area and had neglected to extinguish his candle. The initial fire alarm sounded at approximately 10 a.m. Many citizen volunteers came to help the fire department. Capitol employees and state officials also assisted in fighting the fire, including Governor Albert Cummins. The fire was finally brought under control around 6 p.m., although some newspaper accounts at the time reported that the fire continued smoldering for several days. Crampton Linley was the engineer working with the Capitol Improvement Commission. He was in the building at the time of the fire and was credited with saving the building. Linley crawled through attic areas to close doors separating wings of the Capitol, an action which smothered the flames and brought the fire under control. Sadly, Linley did not live long enough to be recognized for his heroism. The day after the fire, while examining the damage, Linley fell through the ceiling of the House Chamber and died instantly from severe head injuries. The flames had burned through the ceiling and caused much of it to collapse to the floor below, while the lower areas of the building had been damaged by smoke and water. Elmer Garnsey was the artist hired by the Capitol Improvement Commission to decorate the public areas of the building. Therefore, he seemed the logical candidate to be given the additional responsibility of redecorating the areas damaged by the fire. Garnsey had a very different vision for the decoration, which is why the House Chamber, the old Supreme Court Room, and the old Agriculture offices directly below the House Chamber have a design that is very different from the areas of the building untouched by the fire.
Resumo:
The Paleozoic stratigraphic succession in the Catalonian Coastal Ranges spans the interval from Cambrian(?) to Carboniferous, with only one break, separating the pre-Carboniferous part of the sequence from the Carboniferous. The oldest rocks exposed form a sequence of schists, fine grained sandstones, gneisses (laminar pre-Hercynian intrusions), marbles, orto- and para-amphibolites and calcsilicate rocks. comparison with other localities iuggests an Early Cambrian age (or perhaps in part older). Upwards the sequence becomes more monotonous andconsists only of schists (or slates where themetamorphic grade is lower) and thin fine-grained sandstone layers (Cambrian-Ordovician). Still higher in the sequence, an altemation of greywackes and slates is found, with interlayered mud-supported conglomerates at its lower part and acid volcanic rocks which occur throughout the whole sequence. This part of the sequence has provided the oldest faunas known in the Catalonian Coastal Ranges, which indicate the Caradoc. Finally, in its uppermost part, the Ordovician sequence contains some thin limestone layers that contain Ashgill faunas. The Silurian, from Llandovery to Lower Ludlow, consists of black graptolitic shales with dolerite sills, whilst the upper Ludlow, Pridolian and Devonian consist of nodular limestones and marls withpelagic and hemipelagic faunas. The youngest Devonian faunas found correspond in general to the Emsian. The existence of a gap at this point of the sequence suggests the possibility that part of the Devonian could have been eroded. The Carboniferous is characterized by a thick culm sequence (Visean to Westphalian?), resting on thin chert and limestone layers (Tournaisian and Visean). A comparison with neighbouring areas shows a similarity regarding succession and facies with other Paleozoic massifs around the Western Mediterranean.
Resumo:
Advances in implant design, surgical technique, peri-operative antimicrobial prophylaxis and laminar airflow operating room environment have made total joint arthroplasty one of the most successful surgical procedures of all times. Orthopaedic implants, however, remain prone to microbial contamination resulting in persistent risk of implant-associated infection. Treatment of infections associated with orthopaedic devices usually requires appropriate surgical intervention combined with a prolonged antimicrobial therapy. The choice of the best possible treatment regimen depends on duration and pathogenesis of infection, stability of the implant, antimicrobial susceptibility of the pathogen and condition of the surrounding soft tissue. In addition towell known diagnostic procedures new promising tools for rapid and correct microbial diagnosis are being developed as correct diagnosis of the responsible micro-organism and this is paramount for successful treatment of prosthetic joint infection.
Resumo:
We review the progress in the field of front propagation in recent years. We survey many physical, biophysical and cross-disciplinary applications, including reduced-variable models of combustion flames, Reid's paradox of rapid forest range expansions, the European colonization of North America during the 19th century, the Neolithic transition in Europe from 13 000 to 5000 years ago, the description of subsistence boundaries, the formation of cultural boundaries, the spread of genetic mutations, theory and experiments on virus infections, models of cancer tumors, etc. Recent theoretical advances are unified in a single framework, encompassing very diverse systems such as those with biased random walks, distributed delays, sequential reaction and dispersion, cohabitation models, age structure and systems with several interacting species. Directions for future progress are outlined
Resumo:
We review the progress in the field of front propagation in recent years. We survey many physical, biophysical and cross-disciplinary applications, including reduced-variable models of combustion flames, Reid's paradox of rapid forest range expansions, the European colonization of North America during the 19th century, the Neolithic transition in Europe from 13 000 to 5000 years ago, the description of subsistence boundaries, the formation of cultural boundaries, the spread of genetic mutations, theory and experiments on virus infections, models of cancer tumors, etc. Recent theoretical advances are unified in a single framework, encompassing very diverse systems such as those with biased random walks, distributed delays, sequential reaction and dispersion, cohabitation models, age structure and systems with several interacting species. Directions for future progress are outlined
Resumo:
Distribution of the monocarboxylate transporter MCT1 has been investigated in the cortex of normal adult human brain. Similarly to the glucose transporter GLUT1 55 kDa isoform, MCT1 was found to be strongly expressed on blood vessels in all cortical layers. In addition, laminar analysis revealed intense MCT1 expression in the neuropil of layer IV in primary auditory (AI) and visual (VI) areas, while this expression was more homogeneous in the non-primary auditory area STA. The cellular distribution shows that MCT1 is strongly expressed by glial cells often associated with blood vessels that were identified as astrocytes. The observed distribution of MCT1 supports the concept that, under certain circumstances, monocarboxylates could be provided as energy substrates to the adult human brain. Moreover, the distinct laminar pattern of MCT1 expression between primary and non-primary cortical areas may reflect different types of neuronal activity requiring adequate supply of specific energy substrates.
Resumo:
The deposits of two volcanic debris avalanches (VDA I and II) that occur in the upper Maronne valley, northwest sector of Cantal Volcano, France, were studied to establish their mechanisms of formation, transport and deposition. These two volcanic debris avalanches that clearly differ with regard to their structures, textures and extensions, exemplify the wide spectrum of events associated with large-scale sector collapse. VDA I is voluminous (similar to1 km(3) in the upper Maronne valley) and widespread. The deposits comprise two distinct facies: the block facies that forms the intermediate and upper part of the unit and the mixed facies that crops out essentially at the base of the unit. The block facies consists of more or less brecciated lava, block-and-ash-flow breccia and pumice-flow tuff megablocks set in breccias resulting from block disaggregation. Mixing and differential movements are almost absent in this part of the VDA. The mixed facies consists of breccias rich in fine particles that originate from block disagregation, as well as being picked up from the substratum during movement. Mixing and differential movements are predominant in this zone. Analysis of fractures on lava megablocks suggests that shear stress during the initial sliding is the principal cause of fracture. These data strongly indicate that VDA I is purely gravitational and argue for a model in which the initial sliding mass transforms into a flow due to differential in situ fragmentation caused by the shear stress. VDA II is restricted to low-topography areas. Its volume, in the studied area, is about 0.3 km(3). The deposits consist of brecciated, rounded blocks and megablocks set in a fine-grained matrix composed essentially of volcanic glass. This unit is stratified, with a massive layer that contains all the megablocks at the base and in the intermediate part, and in the upper part a normally graded layer that contains only blocks <1 m in size. The different lithologies present are totally mixed. These observations suggest that VDA II may be of the Bezymianny-type and that it underwent a flow transformation from a turbulent to a stratified flow consisting of a basal hyperconcentrated laminar body overlain by a dilute layer. (C) 2000 Elsevier Science B.V. All rights reserved.
Resumo:
Resumo: O objetivo deste trabalho foi avaliar o efeito do cultivo de plantas de copo-de-leite (Zantedeschia aethiopica) em sistema hidropônico, no crescimento vegetativo, no teor de nutrientes na parte aérea e nas trocas gasosas. Utilizou-se o delineamento experimental inteiramente casualizado, em arranjo fatorial triplo (2x2x2), com oito tratamentos, três repetições e oito plantas por parcela. Os tratamentos consistiram de duas dimensões de espuma fenólica (2,5x2,5x2,5 e 5,0x5,0x3,8 cm, expressas em altura x comprimento x largura), duas soluções nutritivas e dois perfis hidropônicos (100 e 150 mm). As plantas de copo-de-leite foram cultivadas em sistema hidropônico fluxo laminar de nutriente (NFT) e apresentaram teores de nutrientes na parte aérea, na seguinte sequência decrescente: K>N>Ca>P>S>Mg para macronutrientes e Fe>Mn>Zn>B>Cu para micronutrientes. Plantas de copo-de-leite cultivadas em sistema hidropônico NFT, em espuma fenólica de 5,0x5,0x3,8 cm e em perfil hidropônico de 150 mm, apresentam maior acúmulo de massa de matéria seca na parte aérea e no rizoma, bem como maiores taxas fotossintéticas, independentemente da solução nutritiva.
Resumo:
Diplomityön ensimmäisessä vaiheessa tutkittiin hydraulisen kuristimen ominaisuuksia ja esiteltiin numeerisesti tehokas kuristinmalli käyttäenpolynomifunktiota virtauksen laminaarisen ja transitioalueen kuvaukseen. Puoliempiirisen mallin paremmuus tulee esille siinä, että kuristimen geometriatietoja ei tarvita laskettaessa virtausta paine-eron perusteella. Reaaliaikasimuloinnissa esiintyy kompromisseja tarkkuuden ja laskentanopeuden välillä. Tätä asiaa tutkittiin kahden virtausalueen kuristinmallilla. Transition paine-eron ja integrointiaika-askelen valinnan vaikutus tarkkuuteen ja laskentanopeuteen tutkittiin. Toisessa vaiheessa tutkittiin mahdollisimman hyvän liiketuntuman tuottamista liikealustalla ohjaussignaalia kehittämällä. Liikealustan liikeradan rajallisuudesta johtuen ohjauksessa on perinteisesti käytetty washout-suodatusta, joka erottelee simuloitavan järjestelmän kiihtyvyyssignaalista vain nopeatkiihtyvyydet. Tässä työssä tutkittiin hitaiden kiihtyvyyksien ottamista mukaan liikealustan ohjaukseen liikealustan liikeradan puitteissa. Tämä toteutettiin kuvaamalla hitaat kiihtyvyydet kallistamalla liikealustaa, jolloin käyttäjään kohdistuva voima saatiin kuvattua gravitaatiota hyväksi käyttäen.
Resumo:
The study of fluid flow in pipes is one of the main topic of interest for engineers in industries. In this thesis, an effort is made to study the boundary layers formed near the wall of the pipe and how it behaves as a resistance to heat transfer. Before few decades, the scientists used to derive the analytical and empirical results by hand as there were limited means available to solve the complex fluid flow phenomena. Due to the increase in technology, now it has been practically possible to understand and analyze the actual fluid flow in any type of geometry. Several methodologies have been used in the past to analyze the boundary layer equations and to derive the expression for heat transfer. An integral relation approach is used for the analytical solution of the boundary layer equations and is compared with the FLUENT simulations for the laminar case. Law of the wall approach is used to derive the empirical correlation between dimensionless numbers and is then compared with the results from FLUENT for the turbulent case. In this thesis, different approaches like analytical, empirical and numerical are compared for the same set of fluid flow equations.
Resumo:
This study was undertaken to determine how dopamine influences cortical development. It focused on morphogenesis of GABAergic neurons that contained the calcium-binding protein parvalbumin (PV). Organotypic slices of frontoparietal cortex were taken from neonatal rats, cultured with or without dopamine, harvested daily (4-30 d), and immunostained for parvalbumin. Expression of parvalbumin occurred in the same regional and laminar sequence as in vivo. Expression in cingulate and entorhinal preceded that in lateral frontoparietal cortices. Laminar expression progressed from layer V to VI and finally II-IV. Somal labeling preceded fiber labeling by 2 d. Dopamine accelerated PV expression. In treated slices, a dense band of PV-immunoreactive neurons appeared in layer V at 7 d in vitro (DIV), and in all layers of frontoparietal cortex at 14 DIV, whereas in control slices such labeling did not appear until 14 and 21 DIV, respectively. The laminar distribution and dendritic branching of PV-immunoreactive neurons were quantified. More labeled neurons were in the superficial layers, and their dendritic arborizations were significantly increased by dopamine. Treatment with a D1 receptor agonist had little effect, whereas a D2 agonist mimicked dopamine's effects. Likewise, the D2 but not the D1 antagonist blocked dopamine-induced changes, indicating that they were mediated primarily by D2 receptors. Parvalbumin expression was accelerated by dopaminergic reinnervation of cortical slices that were cocultured with mesencephalic slices. Coapplication of the glutamate NMDA receptor antagonist MK801 or AP5 blocked dopamine-induced increases in dendritic branching, suggesting that changes were mediated partly by interaction with glutamate to alter cortical excitability.
Resumo:
In this thesis different parameters influencing critical flux in protein ultrafiltration and membrane foul-ing were studied. Short reviews of proteins, cross-flow ultrafiltration, flux decline and criticalflux and the basic theory of Partial Least Square analysis (PLS) are given at the beginning. The experiments were mainly performed using dilute solutions of globular proteins, commercial polymeric membranes and laboratory scale apparatuses. Fouling was studied by flux, streaming potential and FTIR-ATR measurements. Critical flux was evaluated by different kinds of stepwise procedures and by both con-stant pressure and constant flux methods. The critical flux was affected by transmembrane pressure, flow velocity, protein concentration, mem-brane hydrophobicity and protein and membrane charges. Generally, the lowest critical fluxes were obtained at the isoelectric points of the protein and the highest in the presence of electrostatic repulsion between the membrane surface and the protein molecules. In the laminar flow regime the critical flux increased with flow velocity, but not any more above this region. An increase in concentration de-creased the critical flux. Hydrophobic membranes showed fouling in all charge conditionsand, furthermore, especially at the beginning of the experiment even at very low transmembrane pressures. Fouling of these membranes was thought to be due to protein adsorption by hydrophobic interactions. The hydrophilic membranes used suffered more from reversible fouling and concentration polarisation than from irreversible foul-ing. They became fouled at higher transmembrane pressures becauseof pore blocking. In this thesis some new aspects on critical flux are presented that are important for ultrafiltration and fractionation of proteins.
Resumo:
A descontaminação dos explantes é um dos princípios básicos para o sucesso da cultura de tecidos. Um dos problemas diagnosticados na propagação in vitro da figueira, através de gemas apicais, é a contaminação endógena dos explantes por bactérias. Este trabalho teve como objetivo avaliar a eficiência de alguns antibióticos em meio de cultura para o controle de bactérias endógenas em gemas apicais de figueira. Foram avaliados os seguintes tratamentos: T1(sem adição de antibiótico); T2 (30 mg L-1 de cloranfenicol); T3 (250 mg L-1 de ampicilina sódica); T4 (500 mg L-1 de ácido nalidícico); T5 (150 mg L-1 de cefalotina sódica); T6 (500 mg L-1 de tetraciclina), e T7 (400 mg L-1 de norfloxacina). Após coletados em campo, os segmentos de ramos contendo as gemas foram colocados em recipiente com água corrente. Posteriormente, as gemas apicais foram imersas em álcool etílico a 70% e hipoclorito de sódio a 2,5%. Todo procedimento de desinfestação externa dos explantes foi realizado em câmara de fluxo laminar. Os explantes foram inoculados em tubos de ensaio contendo 15 mL de meio básico MS suplementado, após a autoclavagem, com as doses de antibióticos de acordo com os tratamentos estabelecidos. Após a inoculação, os explantes foram mantidos em sala de crescimento por quatro dias no escuro e, em seguida, sob fotoperíodo de 16 horas de luz branca fria e irradiância de 25 µmol m s-1, na temperatura de 22 ± 3ºC. A assepsia realizada externamente nos explantes foi suficiente para o controle de contaminação fúngica, e a adição de antibióticos ao meio, após autoclavagem, foi eficiente para o controle de bactérias endógenas, cujo antibiótico ampicilina sódica proporcionou mais de 90% de explantes sobreviventes.
Resumo:
Työn tavoitteena oli tutkia aaltomaisen profiloinnin vaikutusta suorien jäähdytyskanavien lämmönsiirtoon ja painehäviöön. Erilaisia profiileja oli kymmenen kappaletta ja ne olivat 5mm leveitä ja 30cm pitkiä kukin. Ne laskettiin kolmeulotteisina tapauksina FINFLO-virtausratkaisijalla kolmella eri Reynoldsin luvulla, jotka vastasivat laminaarista, osittain turbulenttista ja lähes kokonaan turbulenttista virtausta. Lämmönsiirtoaine oli kuiva +30°C ilma ja profiloinnin toteutustapa oli toisiaan sivuavat ympyräkaaret kolmella erilaisella säteen arvolla ja kolmella erilaisella aallonpituuden arvolla. Lisäksi laskettiin saman levyisen tasokanavan arvot jokaisella Reynoldsin luvulla kaksiulotteisina tapauksina. Näitä profiloimattomia kanavia pidettiin referenssitapauksina. Tuloksena havaittiin että profiloimalla saadaan yksiselitteisesti suurempi lämpöteho ulos samasta tilavuudesta. Lämmönsiirtokerroin kasvaa profiloinnin avulla parhaimmillaan n. 20% käytetystä turbulenssimallista tai lämmönsiirtokertoimen määritelmästä riippumatta. Painehäviö kasvaa myös aina, mutta kitkakerroin voi hieman pienentyä. Profiilin varsinaisena hyvyyskriteerinä pidettiin lämmönsiirtokertoimen ja kitkakertoimen suhdetta h/f. Se osoittautui riippuvaksi Reynoldsin luvusta ja turbulenssimallista; ASM ja Chien k-έ -mallit ennustavat transitioetäisyyden eri tavalla. Laminaarisilla virtauksilla h/f :n vaihtelu oli vähäistä; suhde vaihteli vain ±5% eri profiilien kesken. ASM-mallilla havaittiin sekundääripyörteilyä, ehkä siksi että se mallintaa anisotrooppisen turbulenssin. Chien k-έ malli ennusti suuremman ja aikaisemmin alkavan turbulenttisuuden kuin ASM. Lisäksi havaittiin mm. että tietyillä profiileilla muodostuu kanavan kapeimpaan kohtaan selvä virtausnopeuden paikallinen minimi seinämän läheisyyden takia.
Resumo:
We review the progress in the field of front propagation in recent years. We survey many physical, biophysical and cross-disciplinary applications, including reduced-variable models of combustion flames, Reid's paradox of rapid forest range expansions, the European colonization of North America during the 19th century, the Neolithic transition in Europe from 13 000 to 5000 years ago, the description of subsistence boundaries, the formation of cultural boundaries, the spread of genetic mutations, theory and experiments on virus infections, models of cancer tumors, etc. Recent theoretical advances are unified in a single framework, encompassing very diverse systems such as those with biased random walks, distributed delays, sequential reaction and dispersion, cohabitation models, age structure and systems with several interacting species. Directions for future progress are outlined