Lubrication efficiency and die design in wire drawing

With the competitive challenge facing business today, the need to keep cost down and quality up is a matter of survival. One way in which wire manufacturers can meet this challenge is to possess a thorough understanding of deformation, friction and lubrication during the wire drawing process, and therefore to make good decisions regarding the selection and application of lubricants as well as the die design. Friction, lubrication and die design during wire drawing thus become the subject of this study. Although theoretical and experimental investigations have been being carried out ever since the establishment of wire drawing technology, many problems remain unsolved. It is therefore necessary to conduct further research on traditional and fundamental subjects such as the mechanics of deformation, friction, lubrication and die design in wire drawing. Drawing experiments were carried out on an existing bull-block under different cross-sectional area reductions, different speeds and different lubricants. The instrumentation to measure drawing load and drawing speed was set up and connected to the wire drawing machine, together with a data acquisition system. A die box connected to the existing die holder for using dry soap lubricant was designed and tested. The experimental results in terms of drawing stress vs percentage area reduction curves under different drawing conditions were analysed and compared. The effects on drawing stress of friction, lubrication, drawing speed and pressure die nozzle are discussed. In order to determine the flow stress of the material during deformation, tensile tests were performed on an Instron universal test machine, using the wires drawn under different area reductions. A polynomial function is used to correlate the flow stress of the material with the plastic strain, on which a general computer program has been written to find out the coefficients of the stress-strain function. The residual lubricant film on the steel wire after drawing was examined both radially and longitudinally using an SEM and optical microscope. The lubricant film on the drawn wire was clearly observed. Therefore, the micro-analysis by SEM provides a way of friction and lubrication assessment in wire drawing.

Design of films for oral dosage formulations

A novel method for tablet coating was studied where a thin polymer film was cast (pre-formed film), dried and applied as a coating hence eliminating the need for using any solvent during the actual coating process. A pre-formed film is initially heating to a temperature where it becomes flexible, a vacuum is applied and the film is then pulled around the tablet. The proposed films (gelatine or cellulose-based) were characterised in terms of their dissolution, swelling, mechanical and thermal properties prior to using them in the novel coating process; selected films were then coated onto tablets containing paracetamol or ibuprofen and the effect of the film on the subsequent dissolution was evaluated. It was found that the pre-formed films could be designed to be fast dissolving and mechanically strong to withstand the stress from the coating process. Also metoclopramide was incorporated in a gelatine film-coating formulation which was then successfully coated on paracetamol-containing core. Gelatin-based films were found to be successful in the novel coating process therefore to be suitable as finished coatings for immediate release dosage forms. Orally disintegrating dosage forms have been identified as a favourable dosage form due to the following reasons: fast onset of drug release, easy to use, not painful and possible increase of amount absorbed to systemic circulation. Selected films formulated for coating studies were also successfully formulated to contain active ingredient suitable for orally disintegrating dosage form; cellulose-based naratriptan-films were studied as orally disintegrating dosage forms of where the effect of formulation on the film properties was studied. It was found that strength of the film can affect the dissolution of the film but it may be the inclusion of specific excipients in the formulation which affect the penetration of the drug through mucosa.

An ultra-sensitive localised surface plasmon resonance fibre device for environmental sensing based upon a structured bi-metal coating

We demonstrate a bi-metal coating (platinum and gold or silver) localised surface plasmon resonance fibre device that produces an index spectral sensitivity of over 11,000 nm/RIU, yielding an index resolution of 5×10-6in the aqueous index regime, consisting of a structured multi-layered thin film on D-shaped fibre. © 2014 SPIE.

Highly sensitive, localized surface plasmon resonance fiber device for environmental sensing, based upon a structured bi-metal array of nano-wires

We demonstrate a bi-metal coated (platinum and gold or silver), localized surface plasmon resonance fiber sensor with an index sensitivity exceeding 11,900 nm/RIU, yielding an index resolution of 2 × 10-5 in the aqueous index regime. This is one of the highest index sensitivities achieved with an optical fiber sensor. The coatings consist of arrays of bi-metal nano-wires (typically 36 nm in radius and 20 μm in length), supported by a silicon dioxide thin film on a thin substrate of germanium, the nano-wires being perpendicular to the longitudinal axis of the D-shaped fiber.

Enhanced zinc oxide and graphene nanostructures for electronics and sensing applications

Zinc oxide and graphene nanostructures are important technological materials because of their unique properties and potential applications in future generation of electronic and sensing devices. This dissertation investigates a brief account of the strategies to grow zinc oxide nanostructures (thin film and nanowire) and graphene, and their applications as enhanced field effect transistors, chemical sensors and transparent flexible electrodes. Nanostructured zinc oxide (ZnO) and low-gallium doped zinc oxide (GZO) thin films were synthesized by a magnetron sputtering process. Zinc oxide nanowires (ZNWs) were grown by a chemical vapor deposition method. Field effect transistors (FETs) of ZnO and GZO thin films and ZNWs were fabricated by standard photo and electron beam lithography processes. Electrical characteristics of these devices were investigated by nondestructive surface cleaning, ultraviolet irradiation treatment at high temperature and under vacuum. GZO thin film transistors showed a mobility of ∼5.7 cm2/V·s at low operation voltage of <5 V and a low turn-on voltage of ∼0.5 V with a sub threshold swing of ∼85 mV/decade. Bottom gated FET fabricated from ZNWs exhibit a very high on-to-off ratio (∼106) and mobility (∼28 cm2/V·s). A bottom gated FET showed large hysteresis of ∼5.0 to 8.0 V which was significantly reduced to ∼1.0 V by the surface treatment process. The results demonstrate charge transport in ZnO nanostructures strongly depends on its surface environmental conditions and can be explained by formation of depletion layer at the surface by various surface states. A nitric oxide (NO) gas sensor using single ZNW, functionalized with Cr nanoparticles was developed. The sensor exhibited average sensitivity of ∼46% and a minimum detection limit of ∼1.5 ppm for NO gas. The sensor also is selective towards NO gas as demonstrated by a cross sensitivity test with N2, CO and CO2 gases. Graphene film on copper foil was synthesized by chemical vapor deposition method. A hot press lamination process was developed for transferring graphene film to flexible polymer substrate. The graphene/polymer film exhibited a high quality, flexible transparent conductive structure with unique electrical-mechanical properties; ∼88.80% light transmittance and ∼1.1742Ω/sq k sheet resistance. The application of a graphene/polymer film as a flexible and transparent electrode for field emission displays was demonstrated.

Desenvolvimento de bionanocompósitos: nano e microcristais de celulose com poli (álcool vinílico) e poli (ácido lático)

This work has the main objective to obtain nano and microcrystals of cellulose, extracted from the pineapple leaf fibres (PALF), as reinforcement for the manufacture of biocomposite films with polymeric matrices of Poly(vinyl alcohol) (PVA) and Poly(lactic acid) (PLA). The polymer matrices and the nano and microcrystals of cellulose were characterised by means of TGA, FTIR and DSC. The analysis was performed on the pineapple leaves to identify the macro and micronutrients. The fibers of the leaves of the pineapple were extracted in a desfibradeira mechanical. The PALF extracted were washed to remove washable impurities and subsequently treated with sodium hydroxide (NaOH) and sodium hypochlorite (NaClO) in the removal of impurities, such as fat, grease, pectates, pectin and lignin. The processed PALF fibers were hydrolysed in sulfuric acid (H2SO4) at a concentration of 13.5 %, to obtain nano and microcrystals of cellulose. In the manufacture of biocomposite films, concentrations of cellulose, 0 %, 1 %, 3 %, 6 %, 9% and 12% were used as reinforcement to the matrices of PVA and PLA. The PVA was dissolved in distilled water at 80 ± 5 oC and the PLA was dissolved in dichloromethane at room temperature. The manufacture of biocompósitos in the form of films was carried out by "casting". Tests were carried out to study the water absorption by the films and mechanical test of resistance to traction according to ASTM D638-10 with a velocity of 50 mm/min.. Chi-square statistical test was used to check for the existence of significant differences in the level of 0.05: the lengths of the PALF, lengths of the nano and microcrystals of cellulose and the procedures used for the filtration using filter syringe of 0.2 μm or filtration and centrifugation. The hydrophilicity of biocompósitos was analysed by measuring the contact angle and the thickness of biocompósitos were compared as well as the results of tests of traction. Statistical T test - Student was also applied with the significance level (0.05). In biodegradation, Sturm test of standard D5209 was used. Nano and microcrystals of cellulose with lengths ranging from 7.33 nm to 186.17 nm were found. The PVA films showed average thicknesses of 0.153 μm and PLA 0.210 μm. There is a strong linear correlation directly proportional between the traction of the films of PVA and the concentration of cellulose in the films (composite) (0,7336), while the thickness of the film was correlated in 0.1404. Nano and microcrystals of cellulose and thickness together, correlated to 0.8740. While the correlation between the cellulose content and tensile strength was weak and inversely proportional (- 0,0057) and thickness in -0.2602, totaling -0,2659 in PLA films. This can be attributed to the nano and microcrystals of cellulose not fully adsorbed to the PLA matrix. In the comparison of the results of the traction of the two polymer matrices, the nano and microcrystals have helped in reducing the traction of the films (composite) of PLA. There was still the degradation of the film of PVA, within a period of 20 days, which was not seen in the PLA film, on the other hand, the observations made in the literature, the average time to start the degradation is above 60 days. What can be said that the films are biodegradable composites, with hydrophilicity and the nano and microcrystals of cellulose, contribute positively in the improvement of the results of polymer matrices used.

Cobayes de la relève : l’artiste et le chercheur à la rencontre de l’expérience

Essai / Essay

An investigation by AFM and TEM of the mechanism of anodic formation of nanoporosity in n-InP in KOH

The early stages of nanoporous layer formation, under anodic conditions in the absence of light, were investigated for n-type InP with a carrier concentration of ∼3× 1018 cm-3 in 5 mol dm-3 KOH and a mechanism for the process is proposed. At potentials less than ∼0.35 V, spectroscopic ellipsometry and transmission electron microscopy (TEM) showed a thin oxide film on the surface. Atomic force microscopy (AFM) of electrode surfaces showed no pitting below ∼0.35 V but clearly showed etch pit formation in the range 0.4-0.53 V. The density of surface pits increased with time in both linear potential sweep and constant potential reaching a constant value at a time corresponding approximately to the current peak in linear sweep voltammograms and current-time curves at constant potential. TEM clearly showed individual nanoporous domains separated from the surface by a dense ∼40 nm InP layer. It is concluded that each domain develops as a result of directionally preferential pore propagation from an individual surface pit which forms a channel through this near-surface layer. As they grow larger, domains meet, and the merging of multiple domains eventually leads to a continuous nanoporous sub-surface region.

Contrary Voices: Heine, Holderlin, and Goethe in the music of Hanns Eisler

Contrary Voices examines composer Hanns Eisler’s settings of nineteenth-century poetry under changing political pressures from 1925 to 1962. The poets’ ideologically fraught reception histories, both under Nazism and in East Germany, led Eisler to intervene in this reception and voice dissent by radically fragmenting the texts. His musical settings both absorb and disturb the charisma of nineteenth-century sound materials, through formal parody, dissonance, and interruption. Eisler’s montage-like work foregrounds the difficult position of a modernist artist speaking both to and against political demands placed on art. Often the very charisma the composer seeks to expose for its power to sway the body politic exerts a force of its own. At the same time, his text-settings resist ideological rigidity in their polyphonic play. A dialogic approach to musical adaptation shows that, as Eisler seeks to resignify Heine’s problematic status in the Weimar Republic, Hölderlin’s appropriation under Nazism, and Goethe’s status as a nationalist symbol in the nascent German Democratic Republic, his music invests these poetic voices with surprising fragility and multivalence. It also destabilizes received gender tropes, in the masculine vulnerability of Eisler’s Heine choruses from 1925 and in the androgynous voices of his 1940s Hölderlin exile songs and later Goethe settings. Cross-reading the texts after hearing such musical treatment illuminates faultlines and complexities less obvious in text-only analysis. Ultimately Eisler’s music translates canonical material into a form as paradoxically faithful as it is violently fragmented.

Cobayes de la relève : l’artiste et le chercheur à la rencontre de l’expérience

Essai / Essay

The Gentleman-Scholar at Home: Domesticity, Masculinity, and Civility in Dutch Seventeenth-Century Genre Painting

This dissertation examines the gentleman-scholar depicted at home in Dutch seventeenth-century genre paintings, focusing primarily on art created in the Northern Netherlands from the 1630s through the 1670s. The methodological approach is art historical but also pertains to history of architecture, history of dress, and gender studies. Employing the framework of the 'Ages of Man', this thesis investigates three related pictorial themes: the student, the scholar in his prime, and the aged scholar. Variations of male scholarly figures and the accoutrements of the study have a long history in Europe. Prototypical sources include religious history paintings of learned hermit-saints; artistic interest in the allegorical Saturnine persona; portraits of famous scholars; and the iconography of scholarly melancholy implied through vanitas allusions in portraiture and genre paintings. While the majority of Dutch genre paintings pertain to themes of women, male domestic routines form a small but important subset of this imagery and have not been studied. By the 1640s, this subject is readily identified by his setting, clothing, and actions. The ubiquity of scholarly attributes, such as books and globes, paired with the wearing of scholarly robes suggest the merits of intellectual curiosity and the privileges of studying as a pastime and designating a room as a study (studeerkamer). Distinct themes in genre also imply the challenges and rewards of scholarly activity pursued in concert with masculine civic and familial duty. Central to the development of this pictorial theme were: the innovative treatment of learned men by Rembrandt and his circle; the fijnschilder subjects of Dou; and the practice of amateur study by elite men, as suggested by the art of Vermeer. As this dissertation reveals, this convention did not grow to be consistent across the Northern Netherlands, nor was artistic interest limited to university towns. Rather, the larger relevance of scholars in Dutch society is evident in visual and literary sources. The domesticity of this figure in genre painting suggests that scholars mediated between an active and a contemplative life. Societal respect was garnered for scholars through their balance of familial and social duties with the honorable pastime of scholarly leisure.

Dar un contenido al tiempo, una interpretación arquetipal del arte en la postmodernidad

La obra de arte tiene la capacidad de convocar en la conciencia colectiva aquello que ha sido excluido, funcionando del mismo modo que los sueños, los síntomas o los mitos. La interpretación arquetipal buscará más allá de las relaciones causales entre un tiempo y su arte, otras de complementariedad o de compensación, que nos llevan hacía un análisis profundo, innatista, más simbólico y más espiritual de la obra de arte. Previamente revisamos los referentes de la postmodernidad y nos preguntamos sobre la muerte del arte en nuestro mundo actual. Para finalizar respondemos a esta pregunta abriendo dos posibilidades opuestas, discrepantes y ambas posibles. En una de ellas apostamos por la muerte del arte, justificada desde los postulados de la psicología arquetipal. En la otra, desde la misma perspectiva, optamos por la supervivencia de un mensaje subyacente en el arte postmoderno, que por tanto permanece vivo y preparado para complementar la conciencia colectiva y nuestra psique actual.

Structural and Electrical Investigation of C 60 –Graphene Vertical Heterostructures

Graphene, with its unique electronic and structural qualities, has become an important playground for studying adsorption and assembly of various materials including organic molecules. Moreover, organic/graphene vertical structures assembled by van der Waals interaction have potential for multifunctional device applications. Here, we investigate structural and electrical properties of vertical heterostructures composed of C60 thin film on graphene. The assembled film structure of C60 on graphene is investigated using transmission electron microscopy, which reveals a uniform morphology of C60 film on graphene with a grain size as large as 500 nm. The strong epitaxial relations between C60 crystal and graphene lattice directions are found, and van der Waals ab initio calculations support the observed phenomena. Moreover, using C60-graphene heterostructures, we fabricate vertical graphene transistors incorporating n-type organic semiconducting materials with an on/off ratio above 3 × 10(3). Our work demonstrates that graphene can serve as an excellent substrate for assembly of molecules, and attained organic/graphene heterostructures have great potential for electronics applications.

Thermomechanical sensitivity of microcantilever in the mid-infrared spectral region

This paper reports the thermomechanical sensitivity of bimaterial cantilevers over a mid-infrared (IR) spectral range (5-10 µm) that is critical both for chemical analysis via vibrational spectroscopy and for direct thermal detection in the 300-700 K range. Mechanical bending sensitivity and noise were measured and modeled for six commercially available microcantilevers, which consist of either an aluminum film on a silicon cantilever or a gold film on a silicon nitride cantilever. The spectral sensitivity of each cantilever was determined by recording cantilever deflection when illuminated with IR light from a monochromator. Rigorous modeling and systematic characterization of the optical system allowed for a quantitative estimate of IR energy incident upon the cantilever. Separately, spectral absorptance of the cantilever was measured using Fourier transform infrared (FT-IR) microscopy, which was compared with analytical models of radiation onto the cantilever and heat flow within the cantilever. The predictions of microcantilever thermomechanical bending sensitivity and noise agree well with measurements, resulting in a ranking of these cantilevers for their potential use in IR measurements.

Prevalence and associated factors of TB/HIV co-infection among HIV Infected patients in Amhara region, Ethiopia.

Background: Tuberculosis is one of the world’s most common causes of death in the era of Human immunodeficiency virus. The purpose of this study was to determine the prevalence and associated factors of TB/HIV co-infection. Methods: Hospital based retrospective studies were conducted among adult HIV-positive patients. Logistic regression method and Chi square test were applied. Results: A total of 571 HIV positive study participants were enrolled. Of these, 158 (27.7%) were found to have pulmonary tuberculosis. Lower baseline CD4 count<200cell/μl, patients who drunk alcohol, patients who were ambulatory at the initiation of ART, patients whose marital status was single were significant predictors for increased risk of tuberculosis in PLWHIV (P <0.05). Non smoker patients, patients in WHO clinical stage I, patients in WHO clinical stage II and ownership of the house had significant protective benefit against risk of TB (P <0.05). Conclusion: The prevalence of TB/HIV co-infection in adults on ART in our study was moderately high. Having advanced clinical status and presence of risk factors were found to be the predicting factors for co-infection. The health office should open TB/HIV co-infection units in the hospitals and health workers should be cautious when a patient has an advanced disease.