Estudo comparativo de pás para aerogeradores de grande porte fabricadas em materiais compósitos reforçadas com fibra de carbono ou fibra de vidro

The research and development of wind turbine blades are essential to keep pace with worldwide growth in the renewable energy sector. Although currently blades are typically produced using glass fiber reinforced composite materials, the tendency for larger size blades, particularly for offshore applications, has increased the interest on carbon fiber reinforced composites because of the potential for increased stiffness and weight reduction. In this study a model of blade designed for large generators (5 MW) was studied on a small scale. A numerical simulation was performed to determine the aerodynamic loading using a Computational Fluid Dynamics (CFD) software. Two blades were then designed and manufactured using epoxy matrix composites: one reinforced with glass fibers and the other with carbon fibers. For the structural calculations, maximum stress failure criterion was adopted. The blades were manufactured by Vacuum Assisted Resin Transfer Molding (VARTM), typical for this type of component. A weight comparison of the two blades was performed and the weight of the carbon fiber blade was approximately 45% of the weight of the fiberglass reinforced blade. Static bending tests were carried out on the blades for various percentages of the design load and deflections measurements were compared with the values obtained from finite element simulations. A good agreement was observed between the measured and calculated deflections. In summary, the results of this study confirm that the low density combined with high mechanical properties of carbon fibers are particularly attractive for the production of large size wind turbine blades

Cinemática de partículas em fluidos de viscosidade variável com o tempo e sua aplicação na construção de poços de petróleo: avaliação durante paradas operacionais

The new oil reservoirs discoveries in onshore and ultra deep water offshore fields and complex trajectories require the optimization of procedures to reduce the stops operation during the well drilling, especially because the platforms and equipment high cost, and risks which are inherent to the operation. Among the most important aspects stands out the drilling fluids project and their behavior against different situations that may occur during the process. By means of sedimentation experiments, a correlation has been validated to determe the sedimentation particles velocity in variable viscosity fluids over time, applying the correction due to effective viscosity that is a shear rate and time function. The viscosity evolution over time was obtained by carrying out rheologic tests using a fixed shear rate, small enough to not interfere in the fluid gelling process. With the sedimentation particles velocity and the fluid viscosity over time equations an iterative procedure was proposed to determine the particles displacement over time. These equations were implemented in a case study to simulate the cuttings sedimentation generated in the oil well drilling during stops operation, especially in the connections and tripping, allowing the drilling fluid project in order to maintain the cuttings in suspension, avoiding risks, such as stuck pipe and in more drastic conditions, the loss of the well

Automação da drenagem no teste de produção convencional em tanque cilíndrico

This document aims to improve the quality of the production test in vertical tanks with free water drain pipes, through a device to control the draining system. This proposal consists of an interface detector close to the tank bottle and a control valve on the pipe-drain; they are attached to a remote supervisor system, which will be minimizing the human influence in the conclusion of the test result. And for more consciousness the work shows the importance of the wells production test in the attendance and diagnosis of the productive process, informing the large number of tests executed and problems of the procedure adopted in the field today. There are many possible sources of uncertainty in this kind of test as shown in the experiments realized in the field; the object prototype of this dissertation will be made in the field, based upon the definition of parameters and characteristics of the devices proposal. For a better definition of the draining process the action results of the assessment test are shown, especially changed some for the understand ing of the real process. It shows the proposal details and the configuration that will be used in the tank of Monte Alegre s field Production Station, explaining the interface detector kind and the control system. It is the base to a pilot project now in development, named as the new project classified in the status of the new technology and production improvement of PETROBRAS in Rio Grande do Norte and Ceará. This dissertation concludes that the automation of the conventional test with the draining system will bring benefits both economically as metrologically, because it reduces the uncertainty of the test procedures with free water draining, and also decreases the number of tests with problems

Implementação de um Módulo de Supervisão para um Sistema de Detecção de Vazamentos em Dutos de Petróleo

The transport of fluids through pipes is used in the oil industry, being the pipelines an important link in the logistics flow of fluids. However, the pipelines suffer deterioration in their walls caused by several factors which may cause loss of fluids to the environment, justifying the investment in techniques and methods of leak detection to minimize fluid loss and environmental damage. This work presents the development of a supervisory module in order to inform to the operator the leakage in the pipeline monitored in the shortest time possible, in order that the operator log procedure that entails the end of the leak. This module is a component of a system designed to detect leaks in oil pipelines using sonic technology, wavelets and neural networks. The plant used in the development and testing of the module presented here was the system of tanks of LAMP, and its LAN, as monitoring network. The proposal consists of, basically, two stages. Initially, assess the performance of the communication infrastructure of the supervisory module. Later, simulate leaks so that the DSP sends information to the supervisory performs the calculation of the location of leaks and indicate to which sensor the leak is closer, and using the system of tanks of LAMP, capture the pressure in the pipeline monitored by piezoresistive sensors, this information being processed by the DSP and sent to the supervisory to be presented to the user in real time

Construction and demolition waste as a source of PVC for recycling

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Sistema de recirculação e rotina de manejo para larvicultura de camarões de água doce Macrobrachium rosenbergii em pequena escala

A recirculating system and a matching management schedule for small-scale freshwater prawn larviculture were described. The system comprised a 140 L larval culture tank in line with a 43 L biofilter filled with 24 L of calcareous substrate. Both the tank and biofilter were made of black colored fiberglass in a conical-cylindrical shape. The turnover rate of the water through the system was 24 times a day; water was pumped by airlift. Results of ten larvicultures showed that the system maintained temperature, dissolved oxygen, pH, salinity, ammonium and nitrite stable and suitable to Macrobrachium rosenbergii larvae. Survival and productivity varied from 60.5 to 72.4% and 37 to 72 post-larvae/L, respectively; both were compatible with results of commercial hatcheries. Therefore, this system may be very useful for research purposes or adapted for small-scale post-larvae production.

Efeito da utilização da levedura desidratada de álcool em dietas para tilápia-do-nilo

Este trabalho teve como objetivo avaliar o efeito da levedura desidratada de álcool (Saccharomyces cerevisae) como substituto do suplemento vitamínico, em dietas de tilápia-do-nilo (Oreochromis niloticus). Trezentos alevinos machos, sexualmente revertidos, com peso médio de 1,5 g, foram distribuídos igualmente em 20 aquários de fibra de vidro, equipados com filtro biológico. Cinco dietas isoprotéicas com 32% de proteína bruta na primeira fase (40 dias) e com 28% de proteína bruta na segunda fase (74 dias) foram fornecidas ad libitum, duas vezes ao dia. A dieta-controle não conti-nha levedura, e as demais apresentavam 10% de levedura. O delineamento foi inteiramente casualizado, com cinco tratamentos e quatro repetições. Não houve influência significativa dos tratamentos sobre o ganho de peso e taxa de crescimento específico. Foi observada, nos peixes alimentados com dietas sem suplemento vitamínico, alta mortalidade. Os peixes que receberam levedura apresentaram menor conteúdo corporal de proteína, e maior, de lipídeos. A levedura desidratada de álcool pode ser usada como fonte de vitaminas hidrossolúveis em dietas para alevinos de tilápia-do-nilo.

Gesso sintético e pinos transcorticais na redução de fratura de tíbia em uma bezerra

Relata-se um caso de fratura de tíbia em uma bezerra de sete meses de idade, 200kg de peso, apresentando fratura fechada, cominutiva em diáfise. A fixação externa foi preferida como método de imobilização óssea, utilizando-se pinos transcorticais e gesso sintético. Obteve-se eficiente imobilização da fratura, com rápida recuperação do animal, dispendendo-se pouco tempo para o pós-operatório (52 dias). A técnica demonstrou ser de fácil realização e passível de ser executada a campo.

Inflammatory responses of Nile tilapia Oreochromis niloticus to Streptococcus agalactiae: effects of vaccination and yeast diet supplement

This study evaluated the effects of dietary supplementation with 0.3% Saccharomyces cerevisiae yeast cell wall and of vaccination against Streptococcus agalactiae on the cellular component of acute inflammation induced in the coelomic cavity of Nile tilapia Oreochromis niloticus and on survival of the fish after challenge. A total of 84 tilapia of mean (+/- SD) weight 125.0 +/- 1.5 g were distributed among twelve 310 l fiberglass tanks according to a 2 x 2 x 3 factorial design in the following manner: with and without supplementation; 2 stimulations (oily solution without S. agalactiae vaccine and vaccination); 15 d later all fish were intracoelomically challenged with 10(8) CFU ml(-1) of a homologous strain of S. agalactiae, and evaluated after 6, 24 and 48 h, with 7 replicates. The fish received the non-supplemented or supplemented diet for a total of 77 d. The vaccination was performed on the 60th day, intracoelomically, as a single injection of 0.5 ml of the vaccine containing 10(8) CFU ml(-1). Fifteen days later, all the fish were challenged with S. agalactiae by means of an intracoelomic inoculation of 10(8) CFU ml(-1). No mortality was observed among the supplemented fish. The fish that were fed the non-supplemented diet and immunized with the bacterium presented a mortality rate of 28.5%. Among the non-supplemented and non-immunized fish, the mortality rate was 38.09%. Supplementation, in both vaccinated and non-vaccinated fish, induced larger accumulations of thrombocytes, lymphocytes and macrophages at the inflammatory focus. The results suggest that supplementation with 0.3% yeast cell wall, in both vaccinated and non-vaccinated fish, improved the inflammatory response of the fish and protected against the challenge. Vaccination increased the defense response, but the effect was stronger when associated with supplementation with S. cerevisiae.

Atuação dos profissionais de enfermagem durante o processo transfusional na UTI de um hostital universitário

Prospective descriptive study with quantitative approach, which aimed to analyze the relationship of the knowledge of Nurses and conduct assistance during the process of transfusion, to patients in the ICU of a university hospital in Natal-RN. The sample consisted of 27 professionals from the nursing staff (5 nurses and 22 nursing technicians), climbing in the ICU during the period of data collection. Data collection was through a questionnaire and structured form of observation, in addition to consulting the diary. The results were organized in SPSS 15.0, tabulated, cathegorized and analyzed by descriptive and inferential statistics. The results show a young population, aged between 21 and 32 years (63.0%), female (85.2%). Among those surveyed were the main type of stock, mostly technical, nursing (ρ= 0006), which have little time to experience - up to 2 years (ρ= 0008), did not know the DRC in 153 (ρ= 0019), held greater number of pipelines care in blood (ρ= 0018), the non-participation in training and feel informed about the process of transfusion, showed no significant differences. As for officials, highlighted only the time to experience more than 2 years, carrying out fewer procedures and feel informed about the blood. As for the pipes during the transfusion process, I found that the majority of pipes observed in both the stock and the staff were inadequate, with predominance in the first, both in the pursuit of conduct regarding the shortfall. The averages of inappropriate conduct, predominantly developed by stock, were higher in all stages for appropriate conduct. Analyzing the knowledge about the disease process, the stock market were those who had lower scores of knowledge in three stages. As the relationship between the pipes care and knowledge, we see that at all stages of the process of transfusion inadequate knowledge of the averages were higher, taking a significant difference in the stages pre-transfusion (ρ= 0012). When analyzing the average of pipes behind, we see that in inappropriate conduct were significantly higher (ρ= 0031), who had searched in inadequate knowledge. As for the frequency of total procedures performed, we found a significant predominance (ρ= 0049) of inappropriate conduct (88.9%) of which 81.5% were developed by professionals who had inadequate knowledge, showing moderate correlation (r = 0,516) and odds ratio of 2,750 times the development of inappropriate conduct in trade with inadequate knowledge. We conclude that the professionals surveyed, especially the technicians of nursing stock, showed serious deficiencies with regard to the development of pipelines and knowledge of the transfusion process, showing the inadequacy to develop this therapy. Facing the foregoing, we accept the alternative hypothesis proposed in the study, because we show that the inadequacy of knowledge about the process of transfusion influence in inappropriate conduct implemented by the nursing staff in ICU.

Estratégia de produção e competitividade :estudo de caso com enfoque de estratégia de foco em empresas de fibra de vidro

The objective of this thesis is to study the theory of production as it relates to and focuses on the strategy of production and competitiveness. The theory utilized was based on Terry Hill s Strategies through the utilization of Matrix of Manufacturing Strategy Issues and supported by the studies of others in this area. The methodology used for the development of this study was based on observing the engagement between two companies over a long period of time. Through interviews and discussions it was possible to collect the necessary information to guide this study; and by constant involvement in each of these companies, their ways of thinking, performing and administrating were observed and understood. In conclusion, this work created an understanding of the importance of the strategy of production, not as the only important element but as an important factor to direct attitudes and decisions in the company under the concept of strategy and competitiveness

Desenvolvimento de antenas de microfita e antenas DRA Broadband

The search for ever smaller device and without loss of performance has been increasingly investigated by researchers involving applied electromagnetics. Antennas using ceramics materials with a high dielectric constant, whether acting as a substract element of patch radiating or as the radiant element are in evidence in current research, that due to the numerous advantages offered, such as: low profile, ability to reduce the its dimensions when compared to other devices, high efficiency of ratiation, suitability the microwave range and/or millimeter wave, low temperature coefficient and low cost. The reason for this high efficiency is that the dielectric losses of ceramics are very low when compared to commercially materials sold used in printed circuit boards, such as fiberglass and phenolite. These characteristics make ceramic devices suitable for operation in the microwave band. Combining the design of patch antennas and/or dielectric resonator antenna (DRA) to certain materials and the method of synthesis of these powders in the manufacture of devices, it s possible choose a material with a dielectric constant appropriate for the design of an antenna with the desired size. The main aim of this work is the design of patch antennas and DRA antennas on synthesis of ceramic powders (synthesis by combustion and polymeric precursors - Pe- chini method) nanostructured with applications in the microwave band. The conventional method of mix oxides was also used to obtain nanometric powders for the preparation of tablets and dielectric resonators. The devices manufactured and studied on high dielectric constant materials make them good candidates to have their small size compared to other devices operating at the same frequency band. The structures analyzed are excited by three different techniques: i) microstrip line, ii) aperture coupling and iii) inductive coupling. The efficiency of these techniques have been investigated experimentally and compared with simulations by Ansoft HFSS, used in the accurate analysis of the electromagnetic behavior of antennas over the finite element method (FEM). In this thesis a literature study on the theory of microstrip antennas and DRA antenna is performed. The same study is performed about the materials and methods of synthesis of ceramic powders, which are used in the manufacture of tablets and dielectric cylinders that make up the devices investigated. The dielectric media which were used to support the analysis of the DRA and/or patch antennas are analyzed using accurate simulations using the finite difference time domain (FDTD) based on the relative electrical permittivity (er) and loss tangent of these means (tand). This work also presents a study on artificial neural networks, showing the network architecture used and their characteristics, as well as the training algorithms that were used in training and modeling some parameters associated with the devices investigated

Sistema inteligente para detecção de vazamentos em dutos de petróleo usando transformada Wavelet e redes neurais

This work consists in the use of techniques of signals processing and artificial neural networks to identify leaks in pipes with multiphase flow. In the traditional methods of leak detection exists a great difficulty to mount a profile, that is adjusted to the found in real conditions of the oil transport. These difficult conditions go since the unevenly soil that cause columns or vacuum throughout pipelines until the presence of multiphases like water, gas and oil; plus other components as sand, which use to produce discontinuous flow off and diverse variations. To attenuate these difficulties, the transform wavelet was used to map the signal pressure in different resolution plan allowing the extraction of descriptors that identify leaks patterns and with then to provide training for the neural network to learning of how to classify this pattern and report whenever this characterize leaks. During the tests were used transient and regime signals and pipelines with punctures with size variations from ½' to 1' of diameter to simulate leaks and between Upanema and Estreito B, of the UN-RNCE of the Petrobras, where it was possible to detect leaks. The results show that the proposed descriptors considered, based in statistical methods applied in domain transform, are sufficient to identify leaks patterns and make it possible to train the neural classifier to indicate the occurrence of pipeline leaks

Medição da densidade óssea através de ondas eletromagnéticas e classificação por MVS

This work holds the purpose of presenting an auxiliary way of bone density measurement through the attenuation of electromagnetic waves. In order to do so, an arrangement of two microstrip antennas with rectangular configuration has been used, operating in a frequency of 2,49 GHz, and fed by a microstrip line on a substrate of fiberglass with permissiveness of 4.4 and height of 0,9 cm. Simulations were done with silica, bone meal, silica and gypsum blocks samples to prove the variation on the attenuation level of different combinations. Because of their good reproduction of the human beings anomaly aspects, samples of bovine bone were used. They were subjected to weighing, measurement and microwave radiation. The samples had their masses altered after mischaracterization and the process was repeated. The obtained data were inserted in a neural network and its training was proceeded with the best results gathered by correct classification on 100% of the samples. It comes to the conclusion that through only one non-ionizing wave in the 2,49 GHz zone it is possible to evaluate the attenuation level in the bone tissue, and that with the appliance of neural network fed with obtained characteristics in the experiment it is possible to classify a sample as having low or high bone density

Construção e análise de desempenho de um fogão solar à concentração utilizando dois focos para cozimento direto

A model of a solar oven with a reflective surface composed of two mirror segments is presented, constituting a two semi-parabolic surfaces made of fiberglass, applied on a ceramic mold, intended to be used in residential and commercial cooking. The reflective surface of the semi-parable is obtained with the use of multiple plain segments of 2 mm wide mirrors. The semi-parabolic structure has visible movements that are comparable to that of the sun. The technical details of the manufacturing and assembling processes will be presented with an analysis of the viability of thermal, economic, and materials of such prototype. This prototype has important social implications and primordial aspects, which combats the ecological damages caused by the wide-scale use of firewood during cooking. It has been demonstrated that the solar oven has the capacity to cook simultaneous two meals distinct for a family of four