Studies on Laser Induced and RF Sputtered Plasma using Optical Emission Spectroscopy and Langmuir Probe

The main objective of the present study is to understand different mechanisms involved in the production and evolution of plasma by the pulsed laser ablation and radio frequency magnetron sputtering. These two methods are of particular interest, as these are well accomplished methods used for surface coatings, nanostructure fabrications and other thin film devices fabrications. Material science researchers all over the world are involved in the development of devices based on transparent conducting oxide (TCO) thin films. Our laboratory has been involved in the development of TCO devices like thin film diodes using zinc oxide (ZnO) and zinc magnesium oxide (ZnMgO), thin film transistors (TFT's) using zinc indium oxide and zinc indium tin oxide, and some electroluminescent (EL) devices by pulsed laser ablation and RF magnetron sputtering.In contrast to the extensive literature relating to pure ZnO and other thin films produced by various deposition techniques, there appears to have been relatively little effort directed towards the characterization of plasmas from which such films are produced. The knowledge of plasma dynamics corresponding to the variations in the input parameters of ablation and sputtering, with the kind of laser/magnetron used for the generation of plasma, is limited. To improve the quality of the deposited films for desired application, a sound understanding of the plume dynamics, physical and chemical properties of the species in the plume is required. Generally, there is a correlation between the plume dynamics and the structural properties of the films deposited. Thus the study of the characteristics of the plume contributes to a better understanding and control of the deposition process itself. The hydrodynamic expansion of the plume, the composition, and SIze distribution of clusters depend not only on initial conditions of plasma production but also on the ambient gas composition and pressure. The growth and deposition of the films are detennined by the thermodynamic parameters of the target material and initial conditions such as electron temperature and density of the plasma.For optimizing the deposition parameters of various films (stoichiometric or otherwise), in-situ or ex-situ monitoring of plasma plume dynamics become necessary for the purpose of repeatability and reliability. With this in mind, the plume dynamics and compositions of laser ablated and RF magnetron sputtered zinc oxide plasmas have been investigated. The plasmas studied were produced at conditions employed typically for the deposition of ZnO films by both methods. Apart from this two component ZnO plasma, a multi-component material (lead zirconium titanate) was ablated and plasma was characterized.

Spray Pyrolysed Tin Chalcogenide Thin Films: Optimization of optoelectronic properties of SnS for possible photovoltaic application as an absorber layer

In the early 19th century, industrial revolution was fuelled mainly by the development of machine based manufacturing and the increased use of coal. Later on, the focal point shifted to oil, thanks to the mass-production technology, ease of transport/storage and also the (less) environmental issues in comparison with the coal!! By the dawn of 21st century, due to the depletion of oil reserves and pollution resulting from heavy usage of oil the demand for clean energy was on the rising edge. This ever growing demand has propelled research on photovoltaics which has emerged successful and is currently being looked up to as the only solace for meeting our present day energy requirements. The proven PV technology on commercial scale is based on silicon but the recent boom in the demand for photovoltaic modules has in turn created a shortage in supply of silicon. Also the technology is still not accessible to common man. This has onset the research and development work on moderately efficient, eco-friendly and low cost photovoltaic devices (solar cells). Thin film photovoltaic modules have made a breakthrough entry in the PV market on these grounds. Thin films have the potential to revolutionize the present cost structure of solar cells by eliminating the use of the expensive silicon wafers that alone accounts for above 50% of total module manufacturing cost.Well developed thin film photovoltaic technologies are based on amorphous silicon, CdTe and CuInSe2. However the cell fabrication process using amorphous silicon requires handling of very toxic gases (like phosphene, silane and borane) and costly technologies for cell fabrication. In the case of other materials too, there are difficulties like maintaining stoichiometry (especially in large area films), alleged environmental hazards and high cost of indium. Hence there is an urgent need for the development of materials that are easy to prepare, eco-friendly and available in abundance. The work presented in this thesis is an attempt towards the development of a cost-effective, eco-friendly material for thin film solar cells using simple economically viable technique. Sn-based window and absorber layers deposited using Chemical Spray Pyrolysis (CSP) technique have been chosen for the purpose

The Surface Plasmon Resonance of Supported Noble Metal Nanoparticles: Characterization, Laser Tailoring, and SERS Application

This work deals with the optical properties of supported noble metal nanoparticles, which are dominated by the so-called Mie resonance and are strongly dependent on the particles’ morphology. For this reason, characterization and control of the dimension of these systems are desired in order to optimize their applications. Gold and silver nanoparticles have been produced on dielectric supports like quartz glass, sapphire and rutile, by the technique of vapor deposition under ultra-high vacuum conditions. During the preparation, coalescence is observed as an important mechanism of cluster growth. The particles have been studied in situ by optical transmission spectroscopy and ex situ by atomic force microscopy. It is shown that the morphology of the aggregates can be regarded as oblate spheroids. A theoretical treatment of their optical properties, based on the quasistatic approximation, and its combination with results obtained by atomic force microscopy give a detailed characterization of the nanoparticles. This method has been compared with transmission electron microscopy and the results are in excellent agreement. Tailoring of the clusters’ dimensions by irradiation with nanosecond-pulsed laser light has been investigated. Selected particles are heated within the ensemble by excitation of the Mie resonance under irradiation with a tunable laser source. Laser-induced coalescence prevents strongly tailoring of the particle size. Nevertheless, control of the particle shape is possible. Laser-tailored ensembles have been tested as substrates for surface-enhanced Raman spectroscopy (SERS), leading to an improvement of the results. Moreover, they constitute reproducible, robust and tunable SERS-substrates with a high potential for specific applications, in the present case focused on environmental protection. Thereby, these SERS-substrates are ideally suited for routine measurements.

The Ri chicken breed and livelihoods in North Vietnam: characterization and prospects

For the last twenty years, the consumption of poultry meat has boomed in Vietnam as in the rest of the developing world. Capital-intensive production has grown rapidly to satisfy this demand. Based on a few numbers of genetically uniform strains, these systems threaten biodiversity. In Vietnam, both rural and urban households still keep indigenous chickens as part of a diversified livelihood portfolio. In line with the national in situ conservation strategy, this study approached the context of local poultry keeping in two rural and one suburban districts of Northern Vietnam. It aimed at understanding households’ willingness, constraints and opportunities for practice improvement, including breeds’ management. As the Ri chicken constitutes the large majority of backyard flocks, two particular objectives of this study are the morpho-biometric characterisation of phenotypic diversity among individuals classified as Ri by farmers and an assessment of their productive potential. Chicken was found to hold a different place in livelihoods of the three districts with consequences on the management of genetic resources. The most favourable conditions for improvement of the Ri breed was found in the rural district of Luong-Son, due to market integration. In the more remote district of Ky-Son, living standards were lower and much would be gained from Ri conservation. Ri breed was the most threatened in the suburban Gia-Lam district, where poultry was a minor side-activity, lacking incentive for genetic management. From motives and constraints, tracks about breeding goals are suggested. Further considerations about conservation, improvement, market integration and livelihoods are proposed.

Molecular Beam Epitaxial Growth of III-V Semiconductor Nanostructures on Silicon Substrates

The main focus and concerns of this PhD thesis is the growth of III-V semiconductor nanostructures (Quantum dots (QDs) and quantum dashes) on silicon substrates using molecular beam epitaxy (MBE) technique. The investigation of influence of the major growth parameters on their basic properties (density, geometry, composition, size etc.) and the systematic characterization of their structural and optical properties are the core of the research work. The monolithic integration of III-V optoelectronic devices with silicon electronic circuits could bring enormous prospect for the existing semiconductor technology. Our challenging approach is to combine the superior passive optical properties of silicon with the superior optical emission properties of III-V material by reducing the amount of III-V materials to the very limit of the active region. Different heteroepitaxial integration approaches have been investigated to overcome the materials issues between III-V and Si. However, this include the self-assembled growth of InAs and InGaAs QDs in silicon and GaAx matrices directly on flat silicon substrate, sitecontrolled growth of (GaAs/In0,15Ga0,85As/GaAs) QDs on pre-patterned Si substrate and the direct growth of GaP on Si using migration enhanced epitaxy (MEE) and MBE growth modes. An efficient ex-situ-buffered HF (BHF) and in-situ surface cleaning sequence based on atomic hydrogen (AH) cleaning at 500 °C combined with thermal oxide desorption within a temperature range of 700-900 °C has been established. The removal of oxide desorption was confirmed by semicircular streaky reflection high energy electron diffraction (RHEED) patterns indicating a 2D smooth surface construction prior to the MBE growth. The evolution of size, density and shape of the QDs are ex-situ characterized by atomic-force microscopy (AFM) and transmission electron microscopy (TEM). The InAs QDs density is strongly increased from 108 to 1011 cm-2 at V/III ratios in the range of 15-35 (beam equivalent pressure values). InAs QD formations are not observed at temperatures of 500 °C and above. Growth experiments on (111) substrates show orientation dependent QD formation behaviour. A significant shape and size transition with elongated InAs quantum dots and dashes has been observed on (111) orientation and at higher Indium-growth rate of 0.3 ML/s. The 2D strain mapping derived from high-resolution TEM of InAs QDs embedded in silicon matrix confirmed semi-coherent and fully relaxed QDs embedded in defectfree silicon matrix. The strain relaxation is released by dislocation loops exclusively localized along the InAs/Si interfaces and partial dislocations with stacking faults inside the InAs clusters. The site controlled growth of GaAs/In0,15Ga0,85As/GaAs nanostructures has been demonstrated for the first time with 1 μm spacing and very low nominal deposition thicknesses, directly on pre-patterned Si without the use of SiO2 mask. Thin planar GaP layer was successfully grown through migration enhanced epitaxy (MEE) to initiate a planar GaP wetting layer at the polar/non-polar interface, which work as a virtual GaP substrate, for the GaP-MBE subsequently growth on the GaP-MEE layer with total thickness of 50 nm. The best root mean square (RMS) roughness value was as good as 1.3 nm. However, these results are highly encouraging for the realization of III-V optical devices on silicon for potential applications.

The Koundoum sheep breed in Niger: morpho-biometric study and description of the production system

The diffusion of highly productive breeds across developing countries goes along with a neglect of indigenous breeds, which are well suited to their environment but often show low yields. Thus, in Niger, the flock of Koundoum sheep are rapidly decreasing. The Koundoum is one of the few wool sheep breeds of Africa and shows important adaptive feature to its native environment, i.e. the humid pastures on the banks of the Niger River. To characterise the breed and to understand its production context, a survey has been conducted in 104 herds in four communes along the Niger River (Kollo, Tillabery, Say and Tera). Nine body measurements, including live weight, were taken on 180 adult sheep (101 females and 79 males). The herds varied from 2 to 60 heads, with a median size of eight animals and two thirds of the herds having less than 10 animals. Mainly fed on natural pastures, 85.6% of the herds received crop residues. Only natural mating was practiced. Veterinary care was restricted to anti-helminthic and some indigenous treatments. The frequent affiliation of breeders to professional unions appeared as favourable to the implementation of a collective conservation program. The Koundoum sheep were white or black coated, with the black colour being most frequent (75.6%). Wattles were present in both sexes at similar frequencies of around 14%. All biometric variables were significantly and positively correlated between them. The thoracic perimeter showed the best correlation with live weight in both males and females. Three variables were selected for live weight prediction: thoracic perimeter, height at withers and rump length. From the present study, it is expected that the in situ conservation of the Koundoum sheep will be highly problematic, due to lack of market opportunities for wool and the willingness of smallholders to get involved in pure Koundoum rearing.

Influence of molecular composition on the development of microstructure from sheared polyethylene melts: Molecular and lamellar templating

A combination of in situ and ex situ X-ray scattering techniques and transmission electron microscopy has been used to study the crystallization behaviour of polyethylene, following the imposition of melt shear. In the case of a branched material, the imposition of shear flow up to a rate of 30 s(-1) was found to induce no anisotropy. Although shearing the linear material only ever induced a very small degree of anisotropy in the melt, for shear rates > 0.15 s(-1), subsequent crystallization resulted in increasing anisotropy. Blends of the above two polyethylenes were produced, in which the linear material constituted the minority fraction (similar to 10%). Isothermal crystallization at temperatures where extensive crystallization of the branched material does not occur demonstrated that the behaviour of the linear component of the sheared blend mirrored that of the linear polyethylene alone. However, in addition, it was found that when crystallized in the presence of an oriented morphology, the branched polymer also formed anisotropic structures. We have termed the process templating, in which the crystallization behaviour of the bulk of the system (similar to 90% branched material) is completely altered (spherulitic to oriented lamellar) by mapping it onto a pre-existing minority structure (similar to 10% linear polymer). (c) 2006 Elsevier Ltd. All rights reserved.

The development of organized structures in polyethylene crystallized from a sheared melt, analyzed by WAXS and TEM

The development of global orientation and morphological features in linear polyethylene crystallizing from a sheared melt are studied using in-situ time-resolving wide angle X-ray scattering (WAXS) and ex-situ transmission electron microscopy. It is found that samples subjected to a shear rate above a critical value of ~1s-1 result in macroscopically oriented structures in the crystallized sample. This critical shear rate appears to be independent of the differences in molecular weight distribution of the samples studied although the morphologies which develop are sensitive to quite small differences in molecular weight distributions. The presence of shish kebabs in the morphology is shown to differ markedly according to variations in the upper molecular weight fraction of the molecular weight distribution, even though the resulting global orientation does not. The WAXS also reveals that areas which evidence no row nucleated structures still realize high degrees of molecular orientation. It is proposed that the formation of shish kebab or lamellar morphologies in these samples is dependent on the critical density of contiguous elongated crystallization nuclei rather than any specific global criteria.

Genotoxicity and composition of particulate matter from biomass burning in the eastern Brazilian Amazon region

In the present study Tradescantia pallida micronucleus (Trad-MCN) bioassay was used to assess the genotoxicity of particulate matter with a mass median aerodynamic diameter less than 10 pm (PM(10)) in Tangara da Serra (MT), a Brazilian Amazon region that suffers the impact of biomass burning. The levels of PM (coarse and fine size fractions) and black carbon (BC) collected were also measured. Furthermore, the alkanes and polycyclic aromatic hydrocarbons (PAHs) were identified and quantified in the samples taken during the burning period by gas chromatography with flame ionization detection (GC-FID). The PM and BC results for both fractions indicate a strong correlation (p < 0.001). The analysis of alkanes indicates an anthropic influence. Retene was the most abundant PAH found, an indicator of biomass burning, and 12 other PAHs considered to be potentially mutagenic and/or carcinogenic were identified in this sample. The Trad-MCN bioassay showed a significant increase in micronucleus frequency during the period of most intense burning, possibly related to the mutagenic PAHs that were found in such extracts. This study demonstrated that Trad-MCN was sensitive and efficient in evaluating the genotoxicity of organic compounds from biomass burning. It further emphasizes the importance of performing chemical analysis, because changes in chemical composition generally have a negative effect on many living organisms. This bioassay (ex situ), using T. pallida with chemical analysis, is thus recommended for characterizing the genotoxicity of air pollution. Crown Copyright (C) 2011 Published by Elsevier Inc. All rights reserved.

Hydrogen purification for fuel cell using CuO/CeO(2)-Al(2)O(3) catalyst

CuO/CeO(2), CuO/Al(2)O(3) and CuO/CeO(2)-Al(2)O(3) catalysts, with CuO loading varying from 1 to 5 wt.%, were prepared by the citrate method and applied to the preferential oxidation of carbon monoxide in a reaction medium containing large amounts of hydrogen (PROX-CO). The compounds were characterized ex situ by X-ray diffraction, specific surface area measurements, temperature-programmed reduction and temperature-programmed reduction of oxidized surfaces; XANES-PROX in situ experiments were also carried out to study the copper oxidation state under PROX-CO conditions. These analyses showed that in the reaction medium the Cu(0) is present as dispersed particles. On the ceria, these metallic particles are smaller and more finely dispersed, resulting in a stronger metal-support interaction than in CuO/Al(2)O(3) or CuO/CeO(2)-Al(2)O(3) catalysts, providing higher PROX-CO activity and better selectivity in the conversion of CO to CO(2) despite the greater BET area presented by samples supported on alumina. It is also shown that the lower CuO content, the higher metal dispersion and consequently the catalytic activity. The redox properties of the ceria support also contributed to catalytic performance. (C) 2010 Elsevier B.V. All rights reserved.

SnO(2)-based materials for pesticide degradation

This study presents the results of the degradation of the pesticide atrazine using electrochemical and photo-assisted electrochemical degradation techniques using SnO(2)-containing electrode of nominal composition electrodes of composition Ti/Ru(x)Sni-(x)O(2) (where X = 0.10, 0.15, 0.20, 0.25 and 0.30). The materials were characterized ex situ and in situ in order to correlate the observed atrazine removal rates with electrode morphology/composition. The results obtained demonstrate the effectiveness of the photo-assisted electrochemical degradation. Using purely electrochemical methods the rate of atrazine removal is almost zero at all the electrodes studied. However, the application of photo-assisted degradation results in almost complete atrazine removal in 1 h of electrolysis. The efficiency of atrazine degradation does not seem to be greatly affected by the electrode material or by SnO(2) content, but the overall COD removal is dependent on the SnO(2) content. Overall, the SnO(2)-containing electrodes do not reach the level of COD removal (maximum similar to 21%) seen for the Ti/Ru(0.3)Ti(0.2)O(2) electrode. An interesting correlation between the morphology factor (phi) and chemical oxygen demand removal is observed. (C) 2010 Elsevier B.V. All rights reserved.

Organic additive-copper(II) complexes as plating precursors

Cu(II) ions previously coordinated with typical electroplating organic additives were investigated as an alternative source of metal for plating bath. The coordination complexes were isolated from reaction between CuSO(4) and organic additives as ligands (oxalate ion, ethylenediamine or imidazole). Deposits over 1010 steel were successfully obtained from electroplated baths using the complexes without any addition of free additives, at pH = 4.5 (H(2)SO(4)/Na(2)SO(4)). These deposits showed better morphologies than deposits obtained from CuSO(4) solution either in the absence or presence of oxalate ion as additive (40 mmol L(-1)), at pH = 4.5 (H(2)SO(4)/Na(2)SO(4))It is suggestive that the starting metal plating coordinated with additives influences the electrode position processes, providing deposits with corrosion potentials shifted over + 200 mV in 0.5 mol L(-1) NaCl (1 mV s(-1)). The resistance against corrosion is sensitive to the type of additive-complex used as precursor. The complex with ethylenediamine presented the best deposit results with the lowest pitting potential (-0.27 V vs 3.0 mol L(-1) CE). It was concluded that the addition of free additives to the electrodeposition baths is not necessary when working with previously coordinated additives. Thus, the complexes generated in ex-situ are good alternatives as plating precursors for electrodeposition bath. (C) 2009 Elsevier B.V. All rights reserved.

Ensaio clínico randomizado da preservação de enxertos hepáticos com solução de perfusão de UW e HTK no transplante ortotópico de fígado

Introdução: A solução de UW (University of Wisconsin) tem sido utilizada como padrão para preservação de enxertos hepáticos para transplante ortotópico de fígado (TOF) desde 1990. Seu custo é alto, e não existem, em nosso meio, estudos clínicos que comparem a sua efetividade com a de outras soluções. A solução de HTK (histidina-triptofano-cetoglutarato) foi desenvolvida inicialmente para cardioplegia, porém estudos experimentais e alguns estudos clínicos retrospectivos demonstraram sua eficácia na preservação hepática, mesmo com tempos de isquemia prolongados. Objetivos: Comparar a efetividade das soluções de preservação de órgãos HTK e UW com relação as variáveis: disfunção primária do enxerto (DPE), tempo de isquemia fria (TIF), complicações de via biliar (CVB), alterações de provas funcionais hepáticas (PFH) e sobrevida do enxerto e dos pacientes. Método: Foram estudados os fígados de doadores de múltiplos órgãos, implantados nos receptores pela técnica de piggyback, segundo ordem cronológica de ingresso em lista de espera no RS no período janeiro de 2003 a agosto de 2004. As soluções de preservação HTK e UW foram utilizadas de forma randomizada em blocos. A perfusão na aorta foi feita com 4 litros de HTK ou 2 litros de UW e a perfusão venosa portal com 1 litro de ambas as soluções, utilizando-se 500 ml para perfusão venosa e arterial adicional ex-situ e armazenagem do enxerto. Realizou-se biópsia hepática em cunha do lobo esquerdo quando a esteatose macroscópica estava presente. A análise bioquímica sérica foi diária na primeira semana e, em 15 e 30 dias pós-operatórios. Resultados: Foram estudados 102 pacientes submetidos ao TOF, sendo 65 no grupo UW (63,7%) e 37 no grupo HTK (36,3%). As frequências de sexo, raça, estado hemodinâmico, o uso de vasopressores e a presença de esteatose nos doadores foram igual nos dois grupos (pα>,05). A idade média dos doadores foi de 38,1 anos (DP +-14,4) no grupo UW e de 44,6 anos (DP +-14,2) no HTK (pα=,036). A distribuição de sexo, raça, idade, etiologia da cirrose, re-transplante, hepatite fulminante, trombose portal e escore de Child-Pugh dos receptores foi igual nos dois grupos (pα>,05). O grupo HTK teve 8 casos (25,8%) de CVB (4 estenose, 2 fístulas e 2 lesões do tipo isquêmica) contra 5 casos (8,6%) do grupo UW (pα=,033) em 89 pacientes que completaram 4 meses de seguimento (OR=2,0; IC 95%=1,2 a 3,5). A média do TIF nos dois grupos foi semelhante (UW= 579,2 min.; HTK= 527,9 min. pα>,05) e não houve diferenças nas incidências de CVB, DPE e óbito com relação a TIF estratificados entre os grupos. Não houve variação nas medianas das PFH (pα>,05 para BT, AST, ALT, FA, GGT, LDH, Fator 5 e TP). A incidência de óbito foi similar em ambos os grupos: UW= 6 (9,4%) e HTK= 4 (11,1%). A incidências de DPE foi de 2,8% no grupo HTK (1 caso) e 9,4% no grupo UW (6 casos) (pα=0,15), dos quais 5 (71,4%) evoluíram para o óbito por não funcionamento primário do enxerto, com ou sem outras morbidades. Conclusão: As soluções de UW e HTK foram igualmente efetivas na preservação dos enxertos hepáticos de doadores cadavéricos na amostra analisada, considerando-se aspectos clínicos, laboratoriais e sobrevida dos pacientes e dos enxertos. A utilização rotineira da solução de HTK poderá diminuir os custos do TOF. A média de idade maior dos doadores e a utilização de um volume reduzido de solução podem ter contribuído para uma incidência maior de CVB no grupo HTK.

Study of Densification Process and Microstructure for Highly Dense Doped MgB2 Bulk Samples

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Laboratory study on the bioremediation of diesel oil contaminated soil from a petrol station

O objetivo do presente estudo foi investigar possíveis métodos para aumentar a taxa de biodegradação aeróbia de hidrocarbonetos (tratamentos ex-situ). Neste trabalho, processos de biorremediação foram aplicados a um solo arenoso com alto nível de contaminação ocasionada por um vazamento de um tanque de armazenamento de óleo diesel subterrâneo em um posto de combustíveis. Experimentos em escala laboratorial (respirômetros de Bartha) foram utilizados para avaliar a biodegradação do óleo diesel. Estímulo da biodegradação foi realizado utilizando-se as técnicas de bioestímulo (adição de soluções de nitrogênio e fósforo ou surfactante Tween 80) e de bioaumento (consórcio bacteriano isolado de um sistema de landfarming). Para investigar as interações entre os fatores otimizadores, e encontrar a melhor combinação entre esses agentes, o estudo foi baseado em um delineamento experimental fatorial completo. A eficiência de biodegradação foi simultaneamente medida com dois métodos: respirométrico (produção de CO2 microbiano) e cromatografia gasosa. Testes de toxicidade aguda com Daphnia similis foram aplicados para examinar a eficiência dos processos em termos de geração de produtos menos tóxicos. Resultados mostraram que todas as estratégias de biorremediação aceleraram a biorremediação natural do solo contaminado e os melhores resultados foram obtidos quando os tratamentos tinham adição de nutrientes. Dados respirométricos indicaram uma máxima mineralização de hidrocarbonetos de 19,8%, obtida com a combinação dos três agentes, com uma remoção de hidrocarbonetos totais de petróleo (TPH) de 45,5% em 55 dias de tratamento. No final dos experimentos, duas espécies predominantes de bactéria foram isoladas e identificadas como Staphylococcus hominis e Kocuria palustris.