Identification of Some Additional Loss Components in High-Power Low-Voltage Permanent Magnet Generators

Permanent magnet generators (PMG) represent the cutting edge technology in modern wind mills. The efficiency remains high (over 90%) at partial loads. To improve the machine efficiency even further, every aspect of machine losses has to be analyzed. Additional losses are often given as a certain percentage without providing any detailed information about the actual calculation process; meanwhile, there are many design-dependent losses that have an effect on the total amount of additional losses and that have to be taken into consideration. Additional losses are most often eddy current losses in different parts of the machine. These losses are usually difficult to calculate in the design process. In this doctoral thesis, some additional losses are identified and modeled. Further, suggestions on how to minimize the losses are given. Iron losses can differ significantly between the measured no-load values and the loss values under load. In addition, with embedded magnet rotors, the quadrature-axis armature reaction adds losses to the stator iron by manipulating the harmonic content of the flux. It was, therefore, re-evaluated that in salient pole machines, to minimize the losses and the loss difference between the no-load and load operation, the flux density has to be kept below 1.5 T in the stator yoke, which is the traditional guideline for machine designers. Eddy current losses may occur in the end-winding area and in the support structure of the machine, that is, in the finger plate and the clamping ring. With construction steel, these losses account for 0.08% of the input power of the machine. These losses can be reduced almost to zero by using nonmagnetic stainless steel. In addition, the machine housing may be subjected to eddy current losses if the flux density exceeds 1.5 T in the stator yoke. Winding losses can rise rapidly when high frequencies and 10–15 mm high conductors are used. In general, minimizing the winding losses is simple. For example, it can be done by dividing the conductor into transposed subconductors. However, this comes with the expense of an increase in the DC resistance. In the doctoral thesis, a new method is presented to minimize the winding losses by applying a litz wire with noninsulated strands. The construction is the same as in a normal litz wire but the insulation between the subconductors has been left out. The idea is that the connection is kept weak to prevent harmful eddy currents from flowing. Moreover, the analytical solution for calculating the AC resistance factor of the litz-wire is supplemented by including an end-winding resistance in the analytical solution. A simple measurement device is developed to measure the AC resistance in the windings. In the case of a litz-wire with originally noninsulated strands, vacuum pressure impregnation (VPI) is used to insulate the subconductors. In one of the two cases studied, the VPI affected the AC resistance factor, but in the other case, it did not have any effect. However, more research is needed to determine the effect of the VPI on litz-wire with noninsulated strands. An empirical model is developed to calculate the AC resistance factor of a single-layer formwound winding. The model includes the end-winding length and the number of strands and turns. The end winding includes the circulating current (eddy currents that are traveling through the whole winding between parallel strands) and the main current. The end-winding length also affects the total AC resistance factor.

Application of a non isotropic turbulence model to stable atmospheric flows and dispersion over 3D topography

A non isotropic turbulence model is extended and applied to three dimensional stably stratified flows and dispersion calculations. The model is derived from the algebraic stress model (including wall proximity effects), but it retains the simplicity of the "eddy viscosity" concept of first order models. The "modified k-epsilon" is implemented in a three dimensional numerical code. Once the flow is resolved, the predicted velocity and turbulence fields are interpolated into a second grid and used to solve the concentration equation. To evaluate the model, various steady state numerical solutions are compared with small scale dispersion experiments which were conducted at the wind tunnel of Mitsubishi Heavy Industries, in Japan. Stably stratified flows and plume dispersion over three distinct idealized complex topographies (flat and hilly terrain) are studied. Vertical profiles of velocity and pollutant concentration are shown and discussed. Also, comparisons are made against the results obtained with the standard k-epsilon model.

Is there correlation between the turbulent eddies size and mechanical hemolysis ?

Hemolytic profile of an artificial device chronically implanted in the cardiovascular system may represent the difference between the success and failure in its long-term performance. Last decades have witnessed efforts on the development of methods capable of predicting red blood cell damage in artificial organs. However, all of them have had limited success to predict hemolysis. The primary cause of this problem is that such models do not take into consideration structures of turbulent flow. The present paper demonstrates that microscopic measurable occurrences of the turbulent flow may be linked to red blood cell trauma. This study suggests that if the smallest turbulent eddies dimension is under 10 m m hemolysis is not dependent on the exposure time and the red blood cells damage depends only on the dissipation of the turbulent energy in the erythrocyte membrane. The analysis reported here opens the possibility of mapping the flow field in artificial assist devices based on the smallest eddy length scales. This is a promising new trend and should be considered in the designing requirements of the next generations of artificial organs.

Hysteresis Losses in Sintered NdFeB Permanent Magnets in Rotating Electrical Machines

Permanent magnet materials are nowadays widely used in the electrical machine manufacturing industry. Eddy current loss models of permanent magnets used in electrical machines are frequently discussed in research papers. In magnetic steel materials we have, in addition to eddy current losses, hysteresis losses when AC or a rotating flux travels through the material. Should a similar phenomenon also be taken into account in calculating the losses of permanent magnets? Actually, every now and then authors seem to assume that some significant hysteresis losses are present in rotating machine PMs. This paper studies the mechanisms of possible hysteresis losses in PMs and their role in PMs when used in rotating electrical machines.

Freshwater dinoflagellates as proxies of cultural eutrophication: a case study from Crawford Lake, Ontario

Crawford Lake, Ontario, provides an ideal natural laboratory to study the response of freshwater dinoflagellates to cultural eutrophication. The anoxic bottom waters that result from meromixis in this small (2.4 ha) but deep (24 m) lake preserve varved sediments that host an exceptional fossil record. These annual layers provide dates for human activity (agriculture and land disturbance) around the lake over the last millennium by both Iroquoian village farmers (ca. A.D. 1268-1486) and Canadian farmers beginning ~A.D. 1883. The well established separate intervals of human activity around Crawford Lake, together with an abundance of available data from other fossil groups, allow us to further investigate the potential use of the cyst of freshwater dinoflagellates in studies of eutrophication. Cyst morphotypes observed have been assigned as Peridinium willei Huitfeldt-Kaas, Peridinium wisconsinense Eddy and Peridinium volzii Lemmermann and Parvodinium inconspicuum (Lemmermann) Carty. The latter two cyst-theca relationships were determined by culturing and by the exceptional preservation of thecae of P. inconspicuum in varves deposited at times of anthropogenic reductions in dissolved oxygen.

Construcción de una cepa de Pichia pastoris sobreproductora de la isoforma de 20 kDa de la hormona del crecimiento humano

Tesis (Maestría en Ciencias con Especialidad en Biología Molecular e Ingeniería Genética) UANL

Researches in graphical statics

UANL

La monumentalité des ensembles architecturaux au site Las Mercedes : une étude volumétrique des couts énergétiques

Mémoire numérisé par la Division de la gestion de documents et des archives de l'Université de Montréal.

Reconstruction des mouvements du plasma dans une région active solaire à l'aide de données d'observation et d'une minimisation Lagrangienne

À ce jour, les différentes méthodes de reconstruction des mouvements du plasma à la surface du Soleil qui ont été proposées présupposent une MHD idéale (Welsch et al., 2007). Cependant, Chae & Sakurai (2008) ont montré l’existence d’une diffusivité magnétique turbulente à la photosphère. Nous introduisons une généralisation de la méthode du Minimum Energy Fit (MEF ; Longcope, 2004) pour les plasmas résistifs. Le Resistive Minimum Energy Fit (MEF-R ; Tremblay & Vincent, 2014) reconstruit les champs de vitesse du plasma et la diffusivité magnétique turbulente qui satisfont à l’équation d’induction magnétique résistive et qui minimisent une fonctionnelle analogue à l’énergie cinétique totale. Une séquence de magnétogrammes et de Dopplergrammes sur les régions actives AR 9077 et AR 12158 ayant chacune produit une éruption de classe X a été utilisée dans MEF-R pour reconstruire les mouvements du plasma à la surface du Soleil. Les séquences temporelles des vitesses et des diffusivités magnétiques turbulentes calculées par MEF-R sont comparées au flux en rayons X mous enregistré par le satellite GOES-15 avant, pendant et après l’éruption. Pour AR 12158, nous observons une corrélation entre les valeurs significatives de la diffusivité magnétique turbulente et de la vitesse microturbulente pour les champs magnétiques faibles.

Nutrient Dynamics in the EEZ of the West Coast of India with Special Reference to the Oxygen Minimum Zone and Denitrification

The present work aims at deciphering the processes that control the nutrient distribution along the EEZ (Exclusive Economic Zone of India) of the west coast of India and to bring out its linkage with primary and secondary productivity. This work assume utmost importance as very few studies have hitherto focused entirely on the EEZ of the west coast of India to address the biochemical responses brought about by monsoons. The present study examines the seasonal variations in physicochemical parameters and associated primary biological responses along the west coast of India. This study targets to measure and understand the shelf ocean exchange in a typical coastal upwelling region of the southeast Arabian Sea, and the influence of convective mixing along the northern part of the west coast of India. The study focuses more directly on coastal upwelling along the southwest coast of India, within the EEZ. The effects of coastal upwelling, eddy formation and the offshore advection are apparent in the present investigation. This has consequences to fisheries and climate, in energy transfer to the food chain and the increased sequestering of carbon in the ocean. The study also focuses on the Oxygen Minimum Zone (OMZ) and dentrification observed along the EEZ of the west coast of India on a seasonal scale. In the study, an attempt is also made to demarcate the geographical boundaries of the denitrification zone in the EEZ of India and on the nature and magnitude of these variations, on a seasonal and inter annual scales

Mixed layer characteristics and hydrography off the west and east coasts of India

In this thesis, a detailed attempt has been made to understand the general hydrography of the upper 300m of the water column, in the eastern Arabian Sea and the western Bay of Bengal, the two contrasting basins in the northern Indian Ocean, using recently collected data sets of Marine Research-Living Resources (MR-LR) assessment programme, funded by Department of Ocean Development, from various cruises, pertaining to different seasons. Initially it discuss the general hydrography of the west and east coasts of India are covered, in the context of mixed layer processes. The study describes the materials and methods . To compare the hydrography of the AS and BOB, a unique MLD(Mixed Layer Depth) definition for AS and BOB is essential, for which the 275 CTD profiles were used. A comparison has been made among the various MLD criteria with the actual MLD. The monthly evolution of MLD, barrier layer thickness and the role of atmospheric forcing on the dynamics of the mixed layer in the AS and BOB were studied. The general hydrography along the west coast of India is described. The upwelling/downwelling, winter cooling processes, in the context of chemical and biological parameters, are also addressed. Finally the general hydrography of the Bay of Bengal is covered. The most striking feature in the hydrography are the signature of an anticyclonic subtropical gyre during spring intermonsoon and a cold core eddy during winter monsoon. The TTS(Typical Tropical Structure) of the euphotic layer was also investigated.

Studies on the Effect of High Energy Ball Milling On the Structural, Electrical and Magnetic Properties of Some Normal Spinets in the Ultrafine Regime

The present work is an attempt to understand the characteristics of high energy ball milling on the structural, electrical and magnetic properties of some normal spinets in the ultra fine regime, Magnetism and magnetic materials have been a fascinating subject for the mankind ever since the discovery of lodestone. Since then, man has been applying this principle of magnetism to build devices for various applications. Magnetism can be classified broadly into five categories. They are diamagnetic, paramagnetic, ferromagnetic antiferromagnetic and ferrimagnetic. Of these, ferro and ferri magnetic materials assume great commercial importance due to their unique properties like appropriate magnetic characteristics, high resistivity and low eddy current losses. The emergence of nanoscience and nanotechnology during the last decade had its impact in the field of magnetism and magnetic materials too. Now, it is common knowledge that materials synthesized in the nanoregime exhibit novel and superlative properties with respect to their coarser sized counterparts in the micron regime. These studies reveal that dielectric properties can be varied appreciably by high-energy ball milling in nanosized zinc ferrites produced by coprecipitation method. A semi conducting behaviour was observed in these materials with the Oxygen vacancies acting as the main charge carrier for conduction, which was produced at the time of coprecipitation and milling. Thus through this study, it was possible to successfully investigate the finite size effects on the structural, electrical and magnetic properties of normal spinels in the ultra fine regime

Dynamics and Thermodynamics of the Arabian Sea Warm Pool

The present study examines the importance of low saline waters and resulting barrier layer in the dynamics of the ASWP using observational data.The oceanic general circulation models (OGCM) are very useful for exploring the processes responsible for the ASWP and their variability. The circulation and thermohaline structure stimulated by an OGCM changes a lot when the resolution is increased from mesoscale to macro scale. For a reasonable simulation of the ASWP, we must include the mesoscale turbulence in numerical models. Especially the SEAS is an eddy prominent region with a horizontal dimension of 100 to 500 km and vertical extent of hundred meters. These eddies may have an important role on the evolution of ASWP, which has not been explored so far.Most of the earlier studies in the SEAS showed that the heat buildup in the mixed layer during the pre-monsoon (March-May) is primarily driven by the surface heat flux through the ocean-atmosphere interface, while the 3-dimensional heat budget of the ML physical processes that are responsible for the formation of the ASWP are unknown. With this background the present thesis also examines the relative importance of mixed layer processes that lead to the formation of warm pool in the SEAS.

Drastic variation in the surface boundary layer parameters over Cochin during the annular solar eclipse: Analysis using sonic anemometer data

Atmospheric surface boundary layer parameters vary anomalously in response to the occurrence of annular solar eclipse on 15th January 2010 over Cochin. It was the longest annular solar eclipse occurred over South India with high intensity. As it occurred during the noon hours, it is considered to be much more significant because of its effects in all the regions of atmosphere including ionosphere. Since the insolation is the main driving factor responsible for the anomalous changes occurred in the surface layer due to annular solar eclipse, occurred on 15th January 2010, that played very important role in understanding dynamics of the atmosphere during the eclipse period because of its coincidence with the noon time. The Sonic anemometer is able to give data of zonal, meridional and vertical wind as well as the air temperature at a temporal resolution of 1 s. Different surface boundary layer parameters and turbulent fluxes were computed by the application of eddy correlation technique using the high resolution station data. The surface boundary layer parameters that are computed using the sonic anemometer data during the period are momentum flux, sensible heat flux, turbulent kinetic energy, frictional velocity (u*), variance of temperature, variances of u, v and w wind. In order to compare the results, a control run has been done using the data of previous day as well as next day. It is noted that over the specified time period of annular solar eclipse, all the above stated surface boundary layer parameters vary anomalously when compared with the control run. From the observations we could note that momentum flux was 0.1 Nm 2 instead of the mean value 0.2 Nm-2 when there was eclipse. Sensible heat flux anomalously decreases to 50 Nm 2 instead of the mean value 200 Nm 2 at the time of solar eclipse. The turbulent kinetic energy decreases to 0.2 m2s 2 from the mean value 1 m2s 2. The frictional velocity value decreases to 0.05 ms 1 instead of the mean value 0.2 ms 1. The present study aimed at understanding the dynamics of surface layer in response to the annular solar eclipse over a tropical coastal station, occurred during the noon hours. Key words: annular solar eclipse, surface boundary layer, sonic anemometer

Presupuestos objetivos para concretar el derecho colectivo a la moralidad administrativa en la contratación estatal. En ejercicio de la acción popular

Este trabajo de investigación presenta parámetros objetivos que permitan concretar en un caso la Moralidad Administrativa por vía de acción popular, como medio control a la moralidad de las personas jurídicas de derecho público