Os polimorfos de carbonato de cálcio: uma síntese fácil de aragonita

Aragonite is a metastable polymorph of calcium carbonate. The calcareous exoskeletons of some organisms like corals or molluscs consist essentially of aragonite. The questions of how, and why these organisms prefer the thermodynamically unstable aragonite for the construction of their hard shells are discussed. The importance of the biomineralization process for the development of new materials is outlined. In the experimental part, a very simple synthesis of polycrystalline aragonite is performed, using carbonated mineral water available at the market. The synthesized aragonite is easily identified by its infrared spectrum.

Evaluation of energy efficiency and best available techniques in pumping processes

The potential for enhancing the energy efficiency of industrial pumping processes is estimated to be in some cases up to 50 %. One way to define further this potential is to implement techniques in accordance to definition of best available techniques in pumping applications. These techniques are divided into three main categories: Design, control method & maintenance and distribution system. In the theory part of this thesis first the definition of best available techniques (BAT) and its applicability on pumping processes is issued. Next, the theory around pumping with different pump types is handled, the main stress being in centrifugal pumps. Other components needed in a pumping process are dealt by presenting different control methods, use of an electric motor, variable speed drive and the distribution system. Last part of the theory is about industrial pumping processes from water distribution, sewage water and power plant applications, some of which are used further on in the empirical part as example cases. For the empirical part of this study four case studies on typical pumping processes from older Master’s these were selected. Firstly the original results were analyzed by studying the distribution of energy consumption between different system components and using the definition of BAT in pumping, possible ways to improve energy efficiency were evaluated. The goal in this study was that by the achieved results it would be possible to identify the characteristic energy consumption of these and similar pumping processes. Through this data it would then be easier to focus energy efficiency actions where they might be the most applicable, both technically and economically.

Computer tools applied to analysis of solar water heaters

The simulation programs are important tools to analyze the different energetic alternatives, including the use of renewable energy. The objective of this study was to analyze comparatively the different computer tools available for modeling of solar water heaters. Among the main simulation software of solar thermal systems, there are: RETScreen International, EnergyPlus, TRNSYS, SolDesigner, SolarPro, e T*SOL. Among the tools mentioned, only EnergyPlus and RETScreen International are free, but they allow obtaining interesting results when applied together. The first one has a detailed module of energy analysis of solar water heaters, while the second one provides an detailed economic feasibility study and an assessment of emissions of greenhouse gases. RETScreen International and EnergyPlus programs are aimed at a diverse audience, including designers, researchers and energy planners.

Use of penetrometers in agriculture: a review

Soil physical quality can be easily and quickly evaluated by using simple equipment to identify levels of soil compaction. Hence, it is necessary to know the variables responsible for changes in the soil penetration resistance (SPR). The aim of this review is to identify the main factors related to the various equipment used for assessing SPR as a soil physical quality indicator in agriculture. This literature review describes the different types of equipment used and its relationship with SPR. A wide range of procedures, devices, and equipments are available. Much of variability in SPR results is related to the equipment model, cone angle and diameter, and penetration rate. Usually, restrictions to root growth are correlated with SPR values above 2-3 MPa. However, comparisons of SPR values obtained under different soil moisture regimes in the same soil type have provided conflicting results of difficult interpretation. In order to minimize these problems, there is a need for standardization of measurement procedures and interpretation, and/or correction of SPR values according to a soil water content of reference.

Energy-efficient control strategies for variable speed driven parallel pumping systems based on pump operation point monitoring with frequency converters

The pumping processes requiring wide range of flow are often equipped with parallelconnected centrifugal pumps. In parallel pumping systems, the use of variable speed control allows that the required output for the process can be delivered with a varying number of operated pump units and selected rotational speed references. However, the optimization of the parallel-connected rotational speed controlled pump units often requires adaptive modelling of both parallel pump characteristics and the surrounding system in varying operation conditions. The available information required for the system modelling in typical parallel pumping applications such as waste water treatment and various cooling and water delivery pumping tasks can be limited, and the lack of real-time operation point monitoring often sets limits for accurate energy efficiency optimization. Hence, alternatives for easily implementable control strategies which can be adopted with minimum system data are necessary. This doctoral thesis concentrates on the methods that allow the energy efficient use of variable speed controlled parallel pumps in system scenarios in which the parallel pump units consist of a centrifugal pump, an electric motor, and a frequency converter. Firstly, the suitable operation conditions for variable speed controlled parallel pumps are studied. Secondly, methods for determining the output of each parallel pump unit using characteristic curve-based operation point estimation with frequency converter are discussed. Thirdly, the implementation of the control strategy based on real-time pump operation point estimation and sub-optimization of each parallel pump unit is studied. The findings of the thesis support the idea that the energy efficiency of the pumping can be increased without the installation of new, more efficient components in the systems by simply adopting suitable control strategies. An easily implementable and adaptive control strategy for variable speed controlled parallel pumping systems can be created by utilizing the pump operation point estimation available in modern frequency converters. Hence, additional real-time flow metering, start-up measurements, and detailed system model are unnecessary, and the pumping task can be fulfilled by determining a speed reference for each parallel-pump unit which suggests the energy efficient operation of the pumping system.

Relationships between crown architecture and available irradiance in two cerrado species with different leaf phenologies

Structural differences between cerrado species with different leaf phenologies are linked to crown architecture, leaf production, and biomass allocation to shoots and leaves. The present study characterized crown structures and the patterns of biomass allocation to leaves and shoots in two woody cerrado species with contrasting leaf phenologies and quantified the irradiance reaching their leaves to determine the best period during the day for photosynthetic activity. The shoots and leaves of five individuals of both Annona coriacea (deciduous) and Hymenaea stigonocarpa (evergreen) were collected along a 50 m transect in a cerrado fragment within the urban perimeter of Catalão - GO, to determine their patterns of biomass allocation in their crowns. The evergreen H. stigonocarpa had significantly higher mean values of shoot inclination (SI), petiole length (PL), leaf area (LA), leaf display index (LDI), and individual leaf area per shoot (ILA), while the deciduous species A. coriacea had significantly higher leaf numbers (LN). The more complex crown of H. stigonocarpa had shoots in more erect positions (orthotropic), with intense self-shading within shoots; A. coriacea, on the other hand, had slanting (plagiotropic) shoots in the crown, allowing similar irradiance levels to all leaf surfaces. The production of plagiotropic shoots by the deciduous species (A. coriacea) is a strategy that enables its use of incident sunlight early in the morning and preventing excessive water loss or excessive irradiance. Hymenaea stigonocarpa (an evergreen), by contrast, had orthotropic shoots and uses intense self-shading as a strategy to avoid excessive irradiance, especially at midday. Differences in crown architectures between evergreen and deciduous species of cerrado sensu stricto can therefore be viewed as adaptations to the environmental light regime.

Spatial modeling techniques for mapping and characterization of acid sulfate soils

Acid sulfate (a.s.) soils constitute a major environmental issue. Severe ecological damage results from the considerable amounts of acidity and metals leached by these soils in the recipient watercourses. As even small hot spots may affect large areas of coastal waters, mapping represents a fundamental step in the management and mitigation of a.s. soil environmental risks (i.e. to target strategic areas). Traditional mapping in the field is time-consuming and therefore expensive. Additional more cost-effective techniques have, thus, to be developed in order to narrow down and define in detail the areas of interest. The primary aim of this thesis was to assess different spatial modeling techniques for a.s. soil mapping, and the characterization of soil properties relevant for a.s. soil environmental risk management, using all available data: soil and water samples, as well as datalayers (e.g. geological and geophysical). Different spatial modeling techniques were applied at catchment or regional scale. Two artificial neural networks were assessed on the Sirppujoki River catchment (c. 440 km2) located in southwestern Finland, while fuzzy logic was assessed on several areas along the Finnish coast. Quaternary geology, aerogeophysics and slope data (derived from a digital elevation model) were utilized as evidential datalayers. The methods also required the use of point datasets (i.e. soil profiles corresponding to known a.s. or non-a.s. soil occurrences) for training and/or validation within the modeling processes. Applying these methods, various maps were generated: probability maps for a.s. soil occurrence, as well as predictive maps for different soil properties (sulfur content, organic matter content and critical sulfide depth). The two assessed artificial neural networks (ANNs) demonstrated good classification abilities for a.s. soil probability mapping at catchment scale. Slightly better results were achieved using a Radial Basis Function (RBF) -based ANN than a Radial Basis Functional Link Net (RBFLN) method, narrowing down more accurately the most probable areas for a.s. soil occurrence and defining more properly the least probable areas. The RBF-based ANN also demonstrated promising results for the characterization of different soil properties in the most probable a.s. soil areas at catchment scale. Since a.s. soil areas constitute highly productive lands for agricultural purpose, the combination of a probability map with more specific soil property predictive maps offers a valuable toolset to more precisely target strategic areas for subsequent environmental risk management. Notably, the use of laser scanning (i.e. Light Detection And Ranging, LiDAR) data enabled a more precise definition of a.s. soil probability areas, as well as the soil property modeling classes for sulfur content and the critical sulfide depth. Given suitable training/validation points, ANNs can be trained to yield a more precise modeling of the occurrence of a.s. soils and their properties. By contrast, fuzzy logic represents a simple, fast and objective alternative to carry out preliminary surveys, at catchment or regional scale, in areas offering a limited amount of data. This method enables delimiting and prioritizing the most probable areas for a.s soil occurrence, which can be particularly useful in the field. Being easily transferable from area to area, fuzzy logic modeling can be carried out at regional scale. Mapping at this scale would be extremely time-consuming through manual assessment. The use of spatial modeling techniques enables the creation of valid and comparable maps, which represents an important development within the a.s. soil mapping process. The a.s. soil mapping was also assessed using water chemistry data for 24 different catchments along the Finnish coast (in all, covering c. 21,300 km2) which were mapped with different methods (i.e. conventional mapping, fuzzy logic and an artificial neural network). Two a.s. soil related indicators measured in the river water (sulfate content and sulfate/chloride ratio) were compared to the extent of the most probable areas for a.s. soils in the surveyed catchments. High sulfate contents and sulfate/chloride ratios measured in most of the rivers demonstrated the presence of a.s. soils in the corresponding catchments. The calculated extent of the most probable a.s. soil areas is supported by independent data on water chemistry, suggesting that the a.s. soil probability maps created with different methods are reliable and comparable.

Intensification of hemicellulose hot-water extraction from spruce wood by parameter tuning

The growing population on earth along with diminishing fossil deposits and the climate change debate calls out for a better utilization of renewable, bio-based materials. In a biorefinery perspective, the renewable biomass is converted into many different products such as fuels, chemicals, and materials, quite similar to the petroleum refinery industry. Since forests cover about one third of the land surface on earth, ligno-cellulosic biomass is the most abundant renewable resource available. The natural first step in a biorefinery is separation and isolation of the different compounds the biomass is comprised of. The major components in wood are cellulose, hemicellulose, and lignin, all of which can be made into various end-products. Today, focus normally lies on utilizing only one component, e.g., the cellulose in the Kraft pulping process. It would be highly desirable to utilize all the different compounds, both from an economical and environmental point of view. The separation process should therefore be optimized. Hemicelluloses can partly be extracted with hot-water prior to pulping. Depending in the severity of the extraction, the hemicelluloses are degraded to various degrees. In order to be able to choose from a variety of different end-products, the hemicelluloses should be as intact as possible after the extraction. The main focus of this work has been on preserving the hemicellulose molar mass throughout the extraction at a high yield by actively controlling the extraction pH at the high temperatures used. Since it has not been possible to measure pH during an extraction due to the high temperatures, the extraction pH has remained a “black box”. Therefore, a high-temperature in-line pH measuring system was developed, validated, and tested for hot-water wood extractions. One crucial step in the measurements is calibration, therefore extensive efforts was put on developing a reliable calibration procedure. Initial extractions with wood showed that the actual extraction pH was ~0.35 pH units higher than previously believed. The measuring system was also equipped with a controller connected to a pump. With this addition it was possible to control the extraction to any desired pH set point. When the pH dropped below the set point, the controller started pumping in alkali and by that the desired set point was maintained very accurately. Analyses of the extracted hemicelluloses showed that less hemicelluloses were extracted at higher pH but with a higher molar-mass. Monomer formation could, at a certain pH level, be completely inhibited. Increasing the temperature, but maintaining a specific pH set point, would speed up the extraction without degrading the molar-mass of the hemicelluloses and thereby intensifying the extraction. The diffusion of the dissolved hemicelluloses from the wood particle is a major part of the extraction process. Therefore, a particle size study ranging from 0.5 mm wood particles to industrial size wood chips was conducted to investigate the internal mass transfer of the hemicelluloses. Unsurprisingly, it showed that hemicelluloses were extracted faster from smaller wood particles than larger although it did not seem to have a substantial effect on the average molar mass of the extracted hemicelluloses. However, smaller particle sizes require more energy to manufacture and thus increases the economic cost. Since bark comprises 10 – 15 % of a tree, it is important to also consider it in a biorefinery concept. Spruce inner and outer bark was hot-water extracted separately to investigate the possibility to isolate the bark hemicelluloses. It was showed that the bark hemicelluloses comprised mostly of pectic material and differed considerably from the wood hemicelluloses. The bark hemicelluloses, or pectins, could be extracted at lower temperatures than the wood hemicelluloses. A chemical characterization, done separately on inner and outer bark, showed that inner bark contained over 10 % stilbene glucosides that could be extracted already at 100 °C with aqueous acetone.

Effects of intracutaneous injections of sterile water in patients with acute low back pain: a randomized, controlled, clinical trial

Intracutaneous sterile water injection (ISWI) is used for relief of low back pain during labor, acute attacks of urolithiasis, chronic neck and shoulder pain following whiplash injuries, and chronic myofascial pain syndrome. We conducted a randomized, double-blinded, placebo-controlled trial to evaluate the effect of ISWI for relief of acute low back pain (aLBP). A total of 68 patients (41 females and 27 males) between 18 and 55 years old experiencing aLBP with moderate to severe pain (scores ≥5 on an 11-point visual analogue scale [VAS]) were recruited and randomly assigned to receive either ISWIs (n=34) or intracutaneous isotonic saline injections (placebo treatment; n=34). The primary outcome was improvement in pain intensity using the VAS at 10, 45, and 90 min and 1 day after treatment. The secondary outcome was functional improvement, which was assessed using the Patient-Specific Functional Scale (PSFS) 1 day after treatment. The mean VAS score was significantly lower in the ISWI group than in the control group at 10, 45, and 90 min, and 1 day after injection (P<0.05, t-test). The mean increment in PSFS score of the ISWI group was 2.9±2.2 1 day after treatment, while that in the control group was 0.9±2.2. Our study showed that ISWI was effective for relieving pain and improving function in aLBP patients at short-term follow-up. ISWI might be an alternative treatment for aLBP patients, especially in areas where medications are not available, as well as in specific patients (e.g., those who are pregnant or have asthma), who are unable to receive medications or other forms of analgesia because of side effects.

Effect of sugar and water contents on non-expanded cassava flour extrudates

The effects of sucrose and water contents on cassava flour processed by extrusion at varied concentrations of sucrose (0-20% w/w) and water (28-42% w/w) were studied by applying response surface methodology. The extrusion of the mixtures was performed in a twin screw extruder fitted to a torque rheometer. The specific mechanical energy (SME) dissipated inside a conical twin-screw extruder was measured. Water absorption index (WAI), water solubility index (WSI) and paste viscosity readings (cold viscosity (CV), peak viscosity (PV), breakdown (BD) and set back (SB)) during a gelatinization-retrogradation cycle measured in a Rapid Visco Analyzer were determined on non-directly extruded products. The results indicated that SME and WSI decreased as a function of water and sucrose contents. WAI and pasting properties were influenced by water content. A non antiplasticizing effect of the sucrose content was observed on pasting properties, suggesting that sucrose did not reduce the availability of water available for gelatinizing cassava flour during the extrusion process. The nature of the optimum point was characterized as a saddle point for WAI, WSI, PV and BD, whereas SME showed a maximum and CV and SB a minimum. The results indicated to be valuable for the production of non-expanded cassava flour extrudates with desirable functional properties for specific end users.

Experimental results and modeling of poultry carcass cooling by water immersion

Poultry carcasses have to be chilled to reduce the central breast temperatures from approximately 40 to 4 °C, which is crucial to ensure safe products. This work investigated the cooling of poultry carcasses by water immersion. Poultry carcasses were taken directly from an industrial processing plant and cooled in a pilot chiller, which was built to investigate the influence of the method and the water stirring intensity on the carcasses cooling. A simplified empiric mathematical model was used to represent the experimental results. These results indicated clearly that the understanding and quantification of heat transfer between the carcass and the cooling water is crucial to improve processes and equipment. The proposed mathematical model is a useful tool to represent the dynamics of carcasses cooling, and it can be used to compare different chiller operational conditions in industrial plants. Therefore, this study reports data and a simple mathematical tool to handle an industrial problem with little information available in the literature.

Physicochemical and sensory characteristics of pan bread samples available in the Brazilian market

Pan bread samples available in the Brazilian market were evaluated for their physicochemical and sensory characteristics. Twelve pan breads, seven white and five whole grain breads, were evaluated. Moisture, water activity (Aw), firmness, and color (L*, a*, b*) of the crumb were evaluated on the first, fourth, seventh, and tenth days after purchasing the breads. Specific volume was evaluated on the first day of analysis with averages of 4.72 and 4.70 mL/g for the white and whole grain breads, respectively. The average results on the first day of analysis were: 37.03% and 41.23% moisture, 0.954 and 0.966 Aw, 276.27 and 267.83 gf firmness, 74.73 and 64.45 L* values, 0.37 and 3.85 a* values, and 15.51 and 18.98 b* values for the white and whole grain breads, respectively. The samples showed an increase in firmness, reduction in moisture and Aw, and no color changes over time. A survey conducted prior to the acceptance test showed that the three most important factors influencing purchase were taste (19.6%), tenderness (16.8%), and expiration date of the product (14.3%). The results showed that 37.2% of the panelists preferred white bread, 62.8% preferred bread with fibers, and 82.6% would probably or definitely buy white bread with fibers.

Draft News Release - Great Lakes Water Quality Agreement

A News Release draft to be sent to "100 newspapers, radio and television stations (virtually all those with offices within 20 miles of the Lakes), make them available to the Press Gallery, special interest groups, trade publication and Mayors etc. of Great Lake-side communities". The release discusses the need for an upgrade to "the 1972 Canada-U.S. Great Lakes Water Quality agreement". Within the document, O'Sullivan is quoted that the agreement "should be upgraded to become a treaty with the United States, so that after all the effort which has already been put into tyring to clean up the Great Lakes we the provision which provides for cancellation by either party giving twelve months (notice) to do so". The total report is 61 pages in length.

Mise au point de nanoparticules polymères pour l'administration parentérale d'agents anticancéreux hydrophobes

Plusieurs agents anticancéreux très puissants sont caractérisés par une solubilité aqueuse limitée et une toxicité systémique importante. Cette dernière serait liée d’une part à la solubilisation des agents anticancéreux à l’aide de surfactifs de bas poids moléculaire, connus pour leur toxicité intrinsèque, et d’autre part, par le manque de spécificité tissulaire des anticancéreux. Les vecteurs colloïdaux à base de polymères permettraient de résoudre certains défis liés à la formulation d’agents anticancéreux hydrophobes. D’abord, les polymères peuvent être sélectionnés afin de répondre à des critères précis de compatibilité, de dégradation et d’affinité pour le médicament à formuler. Ensuite, le fait d’encapsuler l’agent anticancéreux dans un vecteur peut améliorer son efficacité thérapeutique en favorisant son accumulation au niveau du tissu cible, i.e. la tumeur, et ainsi limiter sa distribution au niveau des tissus sains. Des travaux antérieurs menés au sein de notre laboratoire ont mené à la mise au point de micelles à base de poly(N-vinyl-pyrrolidone)-bloc-poly(D,L-lactide) (PVP-b-PDLLA) capables de solubiliser des agents anticancéreux faiblement hydrosolubles dont le PTX. Ce dernier est commercialisé sous le nom de Taxol® et formulé à l’aide du Crémophor EL (CrEL), un surfactif de bas poids moléculaire pouvant provoquer, entre autres, des réactions d’hypersensibilité sévères. Bien que les micelles de PVP-b-PDLLA chargées de PTX aient démontré une meilleure tolérance comparée au Taxol®, leur potentiel de ciblage tumoral et leur efficacité thérapeutique étaient similaires à la forme commerciale à doses égales. Ceci était possiblement dû au fait que les micelles étaient rapidement déstabilisées et ne pouvaient retenir leur cargo suite à leur administration intraveineuse. Nous avons donc décidé de poursuivre les travaux avec un autre type de vecteur, soit des nanoparticules, qui possèdent une stabilité intrinsèque supérieure aux micelles. L’objectif principal de cette thèse de doctorat était donc de mettre au point des nanoparticules polymères pour l’administration parentérale d’agents anticancéreux faiblement solubles dans l’eau. Les nanoparticules devaient permettre d’encapsuler des agents anticancéreux hydrophobes et de les libérer de manière contrôlée sur plusieurs jours. De plus, elles devaient démontrer un temps de circulation plasmatique prolongée afin de favoriser l’accumulation passive du médicament encapsulé au niveau de la tumeur. La première partie du travail visait à employer pour la première fois le copolymère amphiphile PVP-b-PDLLA comme émulsifiant dans la préparation de nanoparticules polymères. Ainsi, une méthode de fabrication des nanoparticules par émulsion huile-dans-eau a été appliquée afin de produire des nanoparticules à base de PDLLA de taille inférieure à 250 nm. Grâce aux propriétés lyoprotectrices de la couronne de PVP présente à la surface des nanoparticules, celles-ci pouvaient retrouver leur distribution de taille initiale après lyophilisation et redispersion en milieu aqueux. Deux anticancéreux hydrophobes, soit le PTX et l’étoposide (ETO), ont été encapsulés dans les nanoparticules et libérés de ces dernières de façon contrôlée sur plusieurs jours in vitro. Une procédure de « salting-out » a été appliquée afin d’améliorer le taux d’incorporation de l’ETO initialement faible étant donnée sa solubilité aqueuse légèrement supérieure à celle du PTX. Le second volet des travaux visait à comparer le PVP comme polymère de surface des nanoparticules au PEG, le polymère le plus fréquemment employé à cette fin en vectorisation. Par le biais d’études d’adsorption de protéines, de capture par les macrophages et de biodistribution chez le rat, nous avons établi une corrélation in vitro/in vivo démontrant que le PVP n’était pas un agent de surface aussi efficace que le PEG. Ainsi, malgré la présence du PVP à la surface des nanoparticules de PDLLA, ces dernières étaient rapidement éliminées de la circulation sanguine suite à leur capture par le système des phagocytes mononucléés. Par conséquent, dans le troisième volet de cette thèse, le PEG a été retenu comme agent de surface, tandis que différents polymères biodégradables de la famille des polyesters, certains synthétiques (PDLLA et copolymères d’acide lactique/acide glycolique), d’autres de source naturelle (poly(hydroxyalkanoates)(PHAs)), ont été investiguées comme matériaux formant le cœur des nanoparticules. Il en est ressorti que les propriétés physicochimiques des polyesters avaient un impact majeur sur l’efficacité d’encapsulation du PTX et son profil de libération des nanoparticules in vitro. Contrairement aux PHAs, les polymères synthétiques ont démontré des taux d’incorporation élevés ainsi qu’une libération contrôlée de leur cargo. Des études de pharmacocinétique et de biodistribution ont démontré que les nanoparticules de PDLLA dotées d’une couronne de PEG conféraient un temps de circulation plasmatique prolongé au PTX et favorisaient son accumulation tumorale. Les nanoparticules polymères représentent donc une alternative intéressante au Taxol®.

Studies on the Deep - Water Crab Charybdis (Goniohellenus ) Smithii Macleay From the Seas Around India

The present study deals with a general introduction which outlines the objective of the study providing an exhaustive review of works on crabs with particular reference to deep-sea forms. In the first section, Taxonomy and Geographical disribution of the crab are dealt with. The species is described in detail based on several male and female specimens obtained from the pelagic and bottom collections, and its identity in Indian waters is established. It is also distinguished from a closely allied species so far not reported from Indian waters. The second section comprises the biology of the species and it is dealt with under four subheading, namely Habit and Habitats, Reproduction, Food and feeding and Proximate composition. The different habitats occupied by juveniles, subadults and adults of the species have been described and discussed in the light of available information on differential distribution of other related species. The reproductive biology is described in various details touching on gross anatomy and histology of the reproductive systems, spermatogenesis, oogenesis, size at maturity, ovarian maturation process, fecundity, egg carriage and breeding. The food and feeding habits of the species have been studied with reference to the different life stages such as juveniles, subadults and adults during the different phases of life based on stomach content analysis. The percentage of meat recovery and protein, carbohydrate and lipid content of meat have been described in the section dealing with proximate composition. In section three the distribution and abundance of the crab for the entire Indian EEZ and some contiguous ares have been described and illustrated in detail separately for pelagic and benthic realms. The size frequency disrtibution, sex ratios, length weight relationship and relative abundance of breeding population in the experimental catches have been dealt with in detail and discussed.