Hydraulisen puomin avoimen piirin koordinaattiohjaus paine-ero-tilavuusvirta-approksimaation avulla

Diplomityön tavoitteena oli kehittää mahdollisimman hyvä koordinaattiohjaus. Sen tuli olla jälkiasennettavissa perinteisen ohjauksen rinnalle työkoneisiin, joissa on käytetty sähköohjattuja proportionaaliventtiileitä. Työssä keskityttiin tutkimaan suuntaventtiilin yli vallitsevasta paine-erosta saatavan tilavuusvirtatiedon hyödyntämistä ohjauksessa. Työn ensimmäisessä vaiheessa koordinaattiohjaus toteutettiin käyttäen 0-peittoisilla karoilla ja karan asematakaisinkytkennällä varustettuja suuntaventtiileitä. Hydrauliseen kuristukseen perustuen saatiin paine-erosta käyttökelpoista tilavuusvirtasignaalia ja koordinaattiohjauksen liikeradan seurannassa oli parhaimmillaan vain 3 cm:n virhe koenosturin työliikkeen pituudella. Toisessa vaiheessa käytettiin työkoneissa yleisesti esiintyvää positiivisin karapeitoin varustettua mobiiliventtiilistöä, jossa oli karakohtaiset painekompensaattorit. Painekompensaattoreiden takia ei paine-eron mittaaminen puhtaasti suuntaventtiilin karan yli ollut mahdollista, jonka takia tyydyttiin koordinaattiohjaus toteuttamaan ilman paineen mittausta luottaen painekompensaattoreiden toimintaan. Käytetyn venttiilistön kavitoinninestotoiminnon huomiointi ohjauksessa jäi ratkaisematta ja se ohitettiin vastusvastaventtiileiden avulla. Koordinaattiohjauksen tarkkuus mobiiliventtiileillä oli vaatimaton ja tulosten toistettavuus heikko. Tulosten perusteella todettiin avoimellakin koordinaattiohjauksella olevan mahdollista saavuttaa lupaava tarkkuus ammattikuljettajiin verrattuna. Mobiiliventtiilistöön liittyvät, työn aikana esiinnousseet epäkohdat olisi ratkaistava ennen käytettyjen menetelmien soveltamista käytännön kohteisiin.

Suljetun sähkönjakeluverkon regulaatio teollisuusympäristössä

Tässä työssä tutkitaan suljetun jakeluverkon regulaatiota yhden suomalaisen teollisuussähköverkon näkökulmasta ja sitä verrataan olemassa olevaan energiaviraston jakeluverkkoja koskevaan säätelymalliin. Työssä tutkitaan verkkoyhtiön kehittämän säätelymallin toimivuutta ja sitä kuinka se täyttää hyvän valvontamallin ominaispiirteet. Tässä työssä ei ole tarkoituksena esittää uutta valvontamallia, vaan tutkia ja arvioida olemassa olevia malleja. Työssä käydään läpi olemassa oleva kolmannen valvontajakson regulaatiomalli sekä muutokset, joita on esitetty tuleville valvontakausille. Työssä taustoitetaan valvontatoimintaa myös yleisen talousteorian ja valvontateorioiden avulla. Tämän taustoituksen avulla tarkastellaan teollisuussähköverkkojen erityisiä ominaisuuksia ja edelleen tutkitun teollisuussähköverkon korkeita käyttövaatimuksia ja syitä tällaisille vaatimuksille. Verkkoyhtiön käyttämä tariffimalli kuvataan myös sen liittyessä sääntelyyn saumattomasti. Työssä todistettiin mallin toimivuus tämän kaltaisessa toimintaympäristössä, jossa käyntivarmuusvaatimus on erittäin korkea. Havainnoissa myös korostuu mallin pitkäjänteisyys ja ennustettavuus. Laskentaesimerkkien avulla arvioidaan liittymähinnoittelun kohtuullisuutta asiakkaalle ja mallin toimivuutta yleensä. Näissä tarkasteluissa havaittiin, että yleisellä tasolla liittymähinnoittelu on kohtuullista asiakkaalle ja se mahdollistaa asiakkaan pääomien tehokkaamman käytön kuin ilman verkkoyhtiötä. Kehittämiskohteina tuodaan esille keskeytyksistä aiheutuvien haittojen käsittely ja se, ettei tällaiseen verkkoympäristöön ole tällä hetkellä toimivaa mittaria, jolla voitaisiin arvioida kuinka hyvin verkkoyhtiö toimii.

Growth and characterisation of certain organic crystals

The thesis presents the results of the investigations on the crystallisation ‘behaviour, detect structure end electrical properties of certain organic crystals---phthslic snhydride end potsssiun scid phthalate Hollow crystals of phthalic snhydride were grown from vapour. the norpholog of these hollow crystals were studied in detail and s. mechanism for their growth has been proposed. A closed crystal—vapour system was used to study the basal plane growth of the whiskers and the sequential growth, observed, confirmed the mechanism suggested for hollow crystals. The dendritic crystals of phthslic enhydride were grown, both iron the melt and solution. The observed morphologies of these dendrites ere described. Bpherulites of phthalic anhydride have been grown by the artificial initiation of nucleation, from melt and solution. The variation of the substructure oi’ these spherulites with the growth tenperature wee investigated. The spherulitic filll having ribbon substructure were etched to reveal dislocations. A mechanism for the formation of the observed etch pattern has been suggested. the slip occurring in these ribbons were studied and the results are presented

Effects of transformation processes in 'jubraka' agroforestry systems of the Nuba Mountains, Sudan, on nutrient fluxes

Intensification processes in homegardens of the Nuba Mountains, Sudan, raise concerns about strongly positive carbon (C) and nutrient balances which are expected to lead to substantial element losses from these agroecosystems, in particular via soil gaseous emissions. Therefore, this thesis aimed at the quantification of C, nitrogen (N), phosphorus (P) and potassium (K) input and output fluxes with a special focus on soil gaseous losses, and the calculation of respective element balances. A further focus in this thesis was rainfall, a valuable resource for rain-fed agriculture in the Nuba Mountains. To minimize negative consequences of the high variability of rainfall, risk reducing mechanisms were developed by rain-fed farmers that may lose their efficacy in the course of climate change effects predicted for East Africa. Therefore, the second objective of this study was to examine possible changes in rainfall amounts during the last 60 years and to provide reliable risk and probability statements of rainfall-induced events of agricultural importance to rain-fed farmers in the Nuba Mountains. Soil gaseous emissions of C (in form of CO2) and N (in form of NH3 and N2O) of two traditional and two intensified homegardens were determined with a portable dynamic closed chamber system. For C gaseous emission rates reached their peak at the onset of the rainy season (2,325 g CO2-C ha-1 h-1 in an intensified garden type) and for N during the rainy season (16 g NH3-N ha-1 h-1 and 11.3 g N2O-N ha-1 h-1, in a traditional garden type). Data indicated cumulative annual emissions of 5,893 kg CO2-C ha-1, 37 kg NH3-N ha-1, and 16 kg N2O-N ha-1. For the assessment of the long-term productivity of the two types of homegardens and the identification of pathways of substantial element losses, a C and nutrient budget approach was used. In three traditional and three intensified homegardens observation plots were selected. The following variables were quantified on each plot between June and December in 2010: soil amendments, irrigation, biomass removal, symbiotic N2 fixation, C fixation by photosynthesis, atmospheric wet and dry deposition, leaching and soil gaseous emissions. Annual balances for C and nutrients amounted to -21 kg C ha-1, -70 kg N ha-1, 9 kg P ha-1 and -117 kg K ha-1 in intensified homegardens and to -1,722 kg C ha-1, -167 kg N ha-1, -9 kg P ha-1 and -74 kg K ha-1 in traditional homegardens. For the analysis of rainfall data, the INSTAT+ software allowed to aggregate long-term daily rainfall records from the Kadugli and Rashad weather stations into daily, monthly and annual intervals and to calculate rainfall-induced events of agricultural importance. Subsequently, these calculated values and events were checked for possible monotonic trends by Mann-Kendall tests. Over the period from 1970 to 2009, annual rainfall did not change significantly for either station. However, during this period an increase of low rainfall events coinciding with a decline in the number of medium daily rainfall events was observed in Rashad. Furthermore, the availability of daily rainfall data enabled frequency and conditional probability calculations that showed either no statistically significant changes or trends resulting only in minor changes of probabilities.

Factores asociados a tratamiento quirúrgico en pacientes con obstrucción intestinal por adherencias

El manejo de la obstrucción intestinal por adherencias es un reto para cualquier especialista en Cirugía debido a que existe controversia sobre el alcance del manejo médico y el momento adecuado para llevar el paciente a cirugía para la resolución del cuadro clínico. En el presente trabajo se pretende, identificar los factores asociados a tratamiento quirúrgico en pacientes con obstrucción intestinal por adherencias. Metodología: Se realizó un estudio de casos y controles en una relación de 1:1, con una recolección de muestra estadística de 48 pacientes en cada grupo, entre mayo 2012 y mayo 2014 en el Hospital Universitario Mayor Mederi y en Barrios Unidos. Se consideraron casos los pacientes intervenidos quirúrgicamente por obstrucción intestinal por bridas y controles los pacientes manejados con tratamiento médico. Se evaluaron factores como edad, antecedentes personales patológicos y quirúrgicos, tiempo de evolución del cuadro clínico, hallazgos en imágenes y laboratorio entre otros. Resultados: Se recolectaron un total de 158 pacientes, (78 casos, 80 controles). Ambas poblaciones fueron comparables (p=0.13). Los factores asociados a tratamiento quirúrgico estadísticamente significativos fueron género masculino, presencia de fiebre al ingreso, el hallazgo de engrosamiento de la pared intestinal y de obstrucción de asa cerrada en imágenes diagnósticas (p<0,05). Discusión: Los principales factores asociados para que un paciente con obstrucción intestinal por bridas requiera de manejo quirúrgico son consistentes con literatura. Se requiere la socialización de los resultados para disminuir la morbimortalidad de nuestros pacientes.

Reconciling the electron counterstreaming and dropout occurrence rates with the heliospheric flux budget

Counterstreaming electrons (CSEs) are treated as signatures of closed magnetic flux, i.e., loops connected to the Sun at both ends. However, CSEs at 1 AU likely fade as the apex of a closed loop passes beyond some distance R, owing to scattering of the sunward beam along its continually increasing path length. The remaining antisunward beam at 1 AU would then give a false signature of open flux. Subsequent opening of a loop at the Sun by interchange reconnection with an open field line would produce an electron dropout (ED) at 1 AU, as if two open field lines were reconnecting to completely disconnect from the Sun. Thus EDs can be signatures of interchange reconnection as well as the commonly attributed disconnection. We incorporate CSE fadeout into a model that matches time-varying closed flux from interplanetary coronal mass ejections (ICMEs) to the solar cycle variation in heliospheric flux. Using the observed occurrence rate of CSEs at solar maximum, the model estimates R ∼ 8–10 AU. Hence we demonstrate that EDs should be much rarer than CSEs at 1 AU, as EDs can only be detected when the juncture points of reconnected field lines lie sunward of the detector, whereas CSEs continue to be detected in the legs of all loops that have expanded beyond the detector, out to R. We also demonstrate that if closed flux added to the heliosphere by ICMEs is instead balanced by disconnection elsewhere, then ED occurrence at 1 AU would still be rare, contrary to earlier expectations.

High bandwidth, large workspace haptic interaction: flying phantoms

It is well understood that for haptic interaction: free motion performance and closed-loop constrained motion performance have conflicting requirements. The difficulties for both conditions are compounded when increased workspace is required as most solutions result in a reduction of achievable impedance and bandwidth. A method of chaining devices together to increase workspace without adverse effect on performance is described and analysed. The method is then applied to a prototype, colloquially known as 'The Flying Phantom', and shown to provide high-bandwidth, low impedance interaction over the full range of horizontal movement across the front of a human user.

Switching curve control of functional electrical stimulation assisted rowing exercise in paraplegia

An indoor rowing machine has been modified for functional electrical stimulation (FES) assisted rowing exercise in paraplegia. To perform the rowing manoeuvre successfully, however, the voluntarily controlled upper body movements must be co-ordinated with the movements of the electrically stimulated paralysed legs. To achieve such co-ordination, an automatic FES controller was developed that employs two levels of hierarchy. At the upper level, a finite state controller identifies the state or phase of the rowing cycle and activates the appropriate lower-level controller, in which electrical stimulation to the paralysed leg muscles is applied with reference to switching curves representing the desired seat velocity as a function of the seat position. In a pilot study, the hierarchical control of FES rowing was shown to be intuitive, reliable and easy to use. Compared with open-loop control of stimulation, all three variants of the closed-loop switching curve controllers used less muscle stimulation per rowing cycle (73% of the open-loop control on average). Further, the closed-loop controller that used switching curves derived from normal rowing kinematics used the lowest muscle stimulation (65% of the open-loop control) and was the most convenient to use for the client.

An improved reliability Cuk based solar inverter with sliding mode control

Many photovoltaic inverter designs make use of a buck based switched mode power supply (SMPS) to produce a rectified sinusoidal waveform. This waveform is then unfolded by a low frequency switching structure to produce a fully sinusoidal waveform. The Cuk SMPS could offer advantages over the buck in such applications. Unfortunately the Cuk converter is considered to be difficult to control using classical methods. Correct closed loop design is essential for stable operation of Cuk converters. Due to these stability issues, Cuk converter based designs often require stiff low bandwidth control loops. In order to achieve this stable closed loop performance, traditional designs invariably need large, unreliable electrolytic capacitors. In this paper, an inverter with a sliding mode control approach is presented which enables the designer to make use of the Cuk converters advantages, while ameliorating control difficulties. This control method allows the selection of passive components based predominantly on ripple and reliability specifications while requiring only one state reference signal. This allows much smaller, more reliable non-electrolytic capacitors to be used. A prototype inverter has been constructed and results obtained which demonstrate the design flexibility of the Cuk topology when coupled with sliding mode control.

Development and experimental identification of a biomechanical model of the trunk for functional electrical stimulation control in paraplegia

Objectives. Theoretic modeling and experimental studies suggest that functional electrical stimulation (FES) can improve trunk balance in spinal cord injured subjects. This can have a positive impact on daily life, increasing the volume of bimanual workspace, improving sitting posture, and wheelchair propulsion. A closed loop controller for the stimulation is desirable, as it can potentially decrease muscle fatigue and offer better rejection to disturbances. This paper proposes a biomechanical model of the human trunk, and a procedure for its identification, to be used for the future development of FES controllers. The advantage over previous models resides in the simplicity of the solution proposed, which makes it possible to identify the model just before a stimulation session ( taking into account the variability of the muscle response to the FES). Materials and Methods. The structure of the model is based on previous research on FES and muscle physiology. Some details could not be inferred from previous studies, and were determined from experimental data. Experiments with a paraplegic volunteer were conducted in order to measure the moments exerted by the trunk-passive tissues and artificially stimulated muscles. Data for model identification and validation also were collected. Results. Using the proposed structure and identification procedure, the model could adequately reproduce the moments exerted during the experiments. The study reveals that the stimulated trunk extensors can exert maximal moment when the trunk is in the upright position. In contrast, previous studies show that able-bodied subjects can exert maximal trunk extension when flexed forward. Conclusions. The proposed model and identification procedure are a successful first step toward the development of a model-based controller for trunk FES. The model also gives information on the trunk in unique conditions, normally not observable in able-bodied subjects (ie, subject only to extensor muscles contraction).

Feedback dew-point sensor utilising optimally cut plastic optical fibres

A plastic optical fibre reflectance sensor that makes full use of the critical angle of the fibres is implemented to monitor dew formation on a Peltier-cooled reflector surface. The optical configuration permits isolation of optoelectronic components from the sensing head and better light coupling between the reflector and the detecting fibre, giving a better signal of the onset of dew formation on the reflector. Continuous monitoring of the rate of change in reflectance as well as the absolute reflectance signals, the use of a novel polymethyl-methacrylate-coated hydrophobic film reflector on the Peltier element and the application of feedback around the point of dew formation, further reduces the possibility of contamination of the sensor head. Under closed-loop operation, the sensor is capable of cycling around the point of dew formation at a frequency of 2.5 Hz.

H∞ robust control design for unsupported paraplegic standing: experimental evaluation

This paper is concerned with the design of robust feedback H~-control systems for the control of the upright posture of paraplegic persons standing. While the subject stands in a special apparatus, stabilising torque at the ankle joint is generated by electrical stimulation of the paralyzed calf muscles. Since the muscles acting as actuators in this setup show a significant degree of nonlinearity, a robust H~-control design is used. The design approach is implemented in experiments with a paraplegic subject. The results demonstrate good performance and closed loop stability over the whole range of operation.

Stable linearization using multilayer neural networks

The main limitation of linearization theory that prevents its application in practical problems is the need for an exact knowledge of the plant. This requirement is eliminated and it is shown that a multilayer network can synthesise the state feedback coefficients that linearize a nonlinear control affine plant. The stability of the linearizing closed loop can be guaranteed if the autonomous plant is asymptotically stable and the state feedback is bounded.

Prosthesis grasp reflex via peripheral nerve control: an in vitro study

Here we present an economical and versatile platform for developing motor control and sensory feedback of a prosthetic hand via in vitro mammalian peripheral nerve activity. In this study, closed-loop control of the grasp function of the prosthetic hand was achieved by stimulation of a peripheral nerve preparation in response to slip sensor data from a robotic hand, forming a rudimentary reflex action. The single degree of freedom grasp was triggered by single unit activity from motor and sensory fibers as a result of stimulation. The work presented here provides a novel, reproducible, economic, and robust platform for experimenting with neural control of prosthetic devices before attempting in vivo implementation.