Physical properties of sediment core AND-2A

Whole-core measurements of Wet Bulk Density (WBD), compressional (P)-wave velocity (Vp), and Magnetic Susceptibility were measured at a sampling interval of 1 or 2 centimetres (cm) throughout the AND-2A drill core for initial core characterisation and on-site correlation with seismic modeling to predict target-reflector depth. Measurements were made using a GEOTEK (Multi-Sensor-Core-Logger MSCL). Density and velocity standards were measured together with core runs of 3-6 metres (m) (and occasionally up to 18 m) throughout the entire depth range to monitor data quality. Drift of the magnetic susceptibility sensor was also monitored and corrected where necessary. These physical properties show a large range of values, reflecting the different nature of the various lithologies including extremely high velocity and density values in individual clasts, and the effects of cementation on porosity. A downcore increase in WBD and Vp occurs in the upper 200 m, however, no systematic trend exists at greater depths although large fluctuations on a m-decimetre- (dm) scale occur. Magnetic susceptibility is generally low (<100 x 10-5 SI), however, four intervals of high (>600 x 10-5 SI) susceptibility occur at 560, 800, 980 and 1 080 mbsf, indicating a relatively greater contribution of volcanic-derived material to the core site in the lower half of the AND-2A core.

Description of recent sediments of Nile Delta, Red Sea and Gulf of Aden (Table 1-3)

The study of textural, structural, chemical, and physical properties of fine-grained recent marine sediments leads to the conclusion that only a few compositional factors are responsible for significant changes in mass physical characteristics in the upper meters below sea bottom. Fossil-induced porosity increases water content and liquid limit. It also seems to have partially influenced the plastic limit and plasticity index of calcareous sandy silts from the Red Sea and the western Gulf of Aden so that they become similar to the montmorillonite rich prodelta clays from the Nile Delta. Diagrams based on liquid limit and plasticity loose their original meaning in these cases. Activity of sediments rich in microorganisms can be higher than that of montmorillonitic clay. The shear strength-depth relationship of normally consolidated sediments is surprisingly little influenced by changes in sand or clay content and clay mineralogy. Only high lime content, submarine erosion and beginning cementation increase the strength considerably. Erosional disconformities near the present surface can be deduced from the strength-depth curve when as little as 1 or 2 m sediment have been removed. Flat or irregular strength-depth curves indicate beginning cementation and probably discontinuous sedimentation, provided the composition of the material remains in some degree constant. In our samples diagenetic pyrite, but no recristallisation of carbonates could be detected under the microscope. Underconsolidation and excess pore-water pressure, factors which tend to foster submarine slides, mud lumps, and diapiric folding, seem to be restricted Varito areas with mainly rapidly deposited, homogeneous or layered sediments. But where an abundance of burrowing organisms increases the vertical permeability of the sediment, normal consolidation and stable deposits are to be expected, at least in the upper meters below the present surface. According to 14C-determinations on calcareous microorganisms the rate of deposition of the investigated sediments seems to range from 26 to 167 cm per 1000 years.

Petrophysical investigations on sediment core CRP-2A from the Ross Sea, Antarctica

A suite of petropysical measurements - velocity versus pressure, bulk density, porosity, matrix density, and magnetic susceptibility -was undertaken on 63 core plugs from CRP-2A. These data are used to calibrate neutron, resistivity, and magnetic susceptibility well logs. Agreement between core-plug magnetic susceptibility measurements and both well-log and whole-core data is excellent. Comparison of core-plug bulk densities with continious well-log density records shows very good agreement. Core-plug measurements of matrix density permit conversion of the well-log and whole-core density records to porosity. Sands and muds exhibit similar downhole compaction patterns, and both patterns are consistent with 250 ± 150 m of exhumation. Pervasive cementation, particularly in the lower half of the core, has affected many CRP-2A petrophysical parameters: (1) fractional porosities are reduced by about 0.05 - 0.10 in the lower part of the hole; (2) velocity and porosity rebound are much smaller than is usually observed for unconsolidated sediments with burial depths similar to CRP-2A; (3) velocities are unusually insensitive to pressure, suggesting that any exhumation-induced microcracks have been scaled subsequently; (4) the velocity/porosity relationship lacks the characteristic signature of exhumation-induced microcracks; (5) the velocity/porosity relationship changes with depth, indicating downhole increase in consolidation; (6) Vp/Vs ratios of the highest-porosity sediments are unusually low, implying enhancement of framework stiffness.

(Table 1, page 661) Average composition of fossil nodules from three localities studied in the Transdanubian Central Mountains of Hungary

Fossil manganese nodules and encrustations from seamount' and basin' localities in the Transdanubian Central Mountains of Hungary are lithologically, mineralogically and chemically similar to some modern marine ferromanganese oxide deposits, and show no evidence of postdepositional changes other than cementation. Five groups of deposits were encountered: Fe/Mn nodules, encrusted shells, pavements, stains, and Fe oxide encrusted intraclasts, the first three of which are specific to the 'seamount' environment and the last to the basins'. Optical and electron microprobe investigation of the samples shows them to exhibit many similarities with modern ferromanganese oxide deposits, and that many of the nodules are surrounded by a halo of dispersed ferromanganese oxides, strongly suggesting that they continued to accrete metals through the pore waters of unlithified sediments for a period after burial. By contrast, pavements which appear to have grown on hardgrounds at the sea floor show little or no evidence of derivation of metals from underlying sediments. Geochemical investigations on the deposits show the seamount' varieties to be closer in composition to most modern nodules and crusts than the basin' varieties, and that the latter are essentially manganese and trace-element-poor ferruginous deposits. Nevertheless, all can be more or less compositionally equated with modern ferromanganese oxide deposits forming in marginal Atlantic environments, which would be in accord with the proposed depositional environment of the Transdanubian Central Mountains based on other evidence.

Effects of rock properties on specific cutting energy in linear cutting of sandstones by picks

Specific cutting energy (SE) has been widely used to assess the rock cuttability for mechanical excavation purposes. Some prediction models were developed for SE through correlating rock properties with SE values. However, some of the textural and compositional rock parameters i.e. texture coefficient and feldspar, mafic, and felsic mineral contents were not considered. The present study is to investigate the effects of previously ignored rock parameters along with engineering rock properties on SE. Mineralogical and petrographic analyses, rock mechanics, and linear rock cutting tests were performed on sandstone samples taken from sites around Ankara, Turkey. Relationships between SE and rock properties were evaluated using bivariate correlation and linear regression analyses. The tests and subsequent analyses revealed that the texture coefficient and feldspar content of sandstones affected rock cuttability, evidenced by significant correlations between these parameters and SE at a 90% confidence level. Felsic and mafic mineral contents of sandstones did not exhibit any statistically significant correlation against SE. Cementation coefficient, effective porosity, and pore volume had good correlations against SE. Poisson's ratio, Brazilian tensile strength, Shore scleroscope hardness, Schmidt hammer hardness, dry density, and point load strength index showed very strong linear correlations against SE at confidence levels of 95% and above, all of which were also found suitable to be used in predicting SE individually, depending on the results of regression analysis, ANOVA, Student's t-tests, and R2 values. Poisson's ratio exhibited the highest correlation with SE and seemed to be the most reliable SE prediction tool in sandstones.