Analytical Evaluation of Squeeze Film Forces in a CMUT With Sealed Air-Filled Cavity

The presence of vacuum inside the cavity of a capacitive micromachined ultrasonic transducer (CMUT) causes the membrane of the device (which is the main vibrating structural component) to deflect towards the substrate, thereby causing a reduction in the effective gap height. This reduction causes a drastic decrease in the pull-in voltage of the device limiting the DC bias at which the device can be operated for maximum efficiency. In addition, this initial deflection of the membrane due to atmospheric pressure, causes significant stress stiffening of the the membrane, changing the natural frequency of the device significantly from the design value. To circumvent the deleterious effects of vacuum in the sealed cavity, we investigate the possibility of using sealed CMUT cavities with air inside at ambient pressure. In order to estimate the transducer loss due to the presence of air in the sealed cavity, we evaluate the resulting damping and determine the forces acting on the vibrating membrane resulting from the compression of the trapped air film. We take into account the flexure of the top vibrating membrane instead of assuming the motion to be parallel-plate like. Towards this end, we solve the linearized Reynolds equation using the appropriate boundary conditions and show that, for a sealed CMUT cavity, the presence of air does not cause any squeeze film damping.

QUANTITATIVE OH PLANAR LASER INDUCED FLUORESCENCE DIAGNOSTICS OF SYNGAS AND METHANE COMBUSTION IN A CAVITY COMBUSTOR

The current work reports quantitative OH species concentration in the cavity of a trapped vortex combustor (TVC) in the context of mixing and flame stabilization studies using both syngas and methane fuels. Planar laser induced fluorescence (PLIF) measurements of OH radical obtained using a Nd: YAG pumped dye laser are quantified using a flat flame McKenna burner. The momentum flux ratio (MFR), defined as the ratio of the cavity fuel jet momentum to that of the guide vane air stream, is observed to be a key governing parameter. At high MFRs similar to 4.5, the flame front is observed to form at the interface of the fuel jet and the air jet stream. This is substantiated by velocity vector field measurements. For syngas, as the MFR is lowered to similar to 0.3, the fuel-air mixing increases and a flame front is formed at the bottom and downstream edge of the cavity where a stratified charge is present. This trend is observed for different velocities at similar equivalence ratios. In case of methane combustion in the cavity, where the MFRs employed are extremely low at similar to 0.01, a different mechanism is observed. A fuel-rich mixture is now observed at the center of the cavity and this mixture undergoes combustion. On further increase of the cavity equivalence ratio, the rich mixture exceeds the flammability limit and forms a thin reaction zone at the interface with air stream. As a consequence, a shear layer flame at the top of the cavity interface with the mainstream is also observed. The equivalence ratio in the cavity also determines the combustion characteristics in the case of fuel-air mixtures that are formed as a result of the mixing. Overall, flame stabilization mechanisms have been proposed, which account for the wide range of MFRs and premixing in the mainstream as well.

Dynamic analysis of V-folded cavity for TEM00 operation of end-pumped solid-state laser

Based on graphic analysis design method of optical resonator, a simple design expression of V-folded cavity of end-pumped solid-state lasers with TEM00 operation is described, which satisfies two criterias of the resonator design. We give numerical simulation of spot size as a function of thermal focal length using this design approach whose advantages are validated experimentally.

An Impact Of Various Shroud Bleed Slot Configurations And Cavity Vanes On Compressor Map Width And The Inducer Flow Field

This paper describes an investigation of map width enhancement and a detailed analysis of the inducer flow field due to various bleed slot configurations and vanes in the annular cavity of a turbocharger centrifugal compressor. The compressor under investigation is used in a turbocharger application for a heavy duty diesel engine of approximately 400 hp. This investigation has been undertaken using a computational fluid dynamics (CFD) model of the full compressor stage, which includes a manual multiblock-structured grid generation method. The influence of the bleed slot flow on the inducer flow field at a range of operating conditions has been analyzed, highlighting the improvement in surge and choked flow capability. The impact of the bleed slot geometry variations and the inclusion of cavity vanes on the inlet incidence angle have been studied in detail by considering the swirl component introduced at the leading edge by the recirculating flow through the slot. Further, the overall stage efficiency and the nonuniform flow field at the inducer inlet have been also analyzed. The analysis revealed that increasing the slot width has increased the map width by about 17%. However, it has a small impact on the efficiency, due to the frictional and mixing losses. Moreover, adding vanes in the cavity improved the pressure ratio and compressor performance noticeably. A detail analysis of the compressor with cavity vanes has also been presented.

Educating the dental team:exploring perceptions of roles and identities

Interprofessional education (IPE) should help to promote a team-based approach to professional practice but there are barriers to its implementation including professional identity. The aim of this study was to use a qualitative research methodology to explore dental and dental care professional (DCP) students' perceptions of professional roles and identities in the dental team. Data were collected by means of focus groups from a purposive sample of dental and DCP students and were audio recorded, transcribed and analysed using an explanatory framework. Five common themes emerged around the issue of professional roles and identity in the dental team. The results indicate that professional identity was an important factor in team development and was determined by direct responsibility for patient care and by the amount of clinical experience acquired. Professional identity within a team context was perceived as different from professional identity per se. Dental students were found to lack confidence in their role as team leaders which was related to their lack of knowledge of team roles, responsibilities and experience. The role of the dental technician was perceived as 'outside' the dental team due to lack of patient interaction.

An analysis of the attitudes of dental patients attending general dental practice in Galway

AIM: To describe the patterns of dental attendance and attitudes towards tooth loss of general dental practice patients in Galway.

OBJECTIVES: 1. To determine the pattern of adult dental attendance in general practices in Galway; and, 2. To examine the oral health attitudes of these patients.

METHOD: Questionnaires were distributed to 311 consecutive adult patients in the waiting rooms of ten general dental practices in Galway, which were randomly selected from the telephone directory.

RESULTS: A total of 254 of the 311 questionnaires distributed were fully completed, returned and included in the results, giving a response rate of 81.7%. A total of 59% of dentate participants attended their dentist for annual or biannual examinations compared to 23% of edentate patients. Some 10.5% of medical card holders and 0.5% of non-medical card holders were edentulous.

CONCLUSIONS: The data from the survey indicated that medical card holders in Galway were more likely to be edentulous than nonmedical card holders. Edentate patients were less likely to be regular dental attenders than dentate patients.

A study of patient attitudes towards fasting prior to intravenous sedation for dental treatment in a dental hospital department

INTRODUCTION: Intravenous sedation is the most commonly used method of sedation for the provision of adult dental care. However, disparity exists in pre-operative fasting times in use for patients throughout the United Kingdom.

AIMS: The aims of the study were to obtain information on the effects of existing extended pre-operative fasting regimens, to canvas patient opinions on the fasting process, and to record their positive and negative experiences associated with it.

METHODS: A prospective cross-sectional descriptive study using survey methodology was conducted of adult patients attending a dental hospital for operative treatment under intravenous sedation. Sixty-four questionnaires were distributed over a four-month period, beginning 2nd October 2007.

RESULTS: The surveyed patient pool consisted of 38 females and 14 males with a mean age of 32.4 years. The response rate achieved was 81.2%. Seventy-one per cent of patients indicated that normally they consumed something for breakfast, the most common items being tea and toast. Fifty-one per cent of patients indicated that they would wish to eat the same as normal prior to their appointment and 59% wished to drink as normal. Only 19% of respondents reported that they did not wish to eat anything, with 8% preferring not to drink anything at all. Seventy-nine per cent of the patients reported that they had experienced at least one adverse symptom after fasting and 42% had experienced two or more such symptoms. In general, those patients with more experience of sedation found fasting less unpleasant than those attending for the first time (P<0.05). In addition, one-quarter of all patients indicated that the fasting process had made them feel more nervous about their sedation appointment.

CONCLUSIONS: The extended fasting regimen prior to intravenous sedation appeared to affect patients' wellbeing, as the majority reported adverse symptoms.

Proportioning variability in the dispensation of hand-mixed dental cements

Objectives: The purpose of this investigation was to determine for dispensed multiples (1 through 4) of powder (P) and liquid (L) in hand-mixed dental cement whether: (1) the mean (P/L) ratio (m/m) and (2) the maximum difference in (P/L) ratio is dependent on the number of multiples dispensed. The Null hypotheses were: (a) mean (P/L) ratio is independent of the number of multiples dispensed and (b) maximum difference in (P/L) ratio is independent of the number of multiples dispensed.
Methods: The materials investigated are listed in the Table. The masses of dispensed aliquots of powder and liquid were measured by a single operator (n=10, for multiples 1 through 4) on a 4-place analytical balance. All measurements were made independently and all possible (P/L) ratios calculated for each sample. The effect of multiple dispensations on (P/L) ratios and maximum (P/L) differences was by one-way ANOVA and linear regression, respectively, with the Tukey post-hoc correction for multiple comparisons.MULTIPLE DISPENSEDDISPENSED MU(x1)(x2)(x3)(x4)Zinc phosphateHeraeus12.271(0.691)a13.051(1.269)b13.215(0.824)b13.118(1.149)bFuji IXGC4.209(0.373)a4.085(0.275)b4.095(0.226)b4.095(0.217)bIRMDentsply7.933(0.767)a7.430(0.451)b7.977(0.729)a8.186(0.929)aKetac-Cem3M Espe9.6206(0.613)a9.714(0.523)a9.298(0.314)b9.321(0.292)bMean (SD) powder/liquid ratio (m/m). Superscript letters represent significances (α = 0.05) within each material
Results: Mean (SD) (P/L) ratios are presented in the Table. Null hypothesis (a) is rejected: either (x1) or (x2) dispensation yields a different (P/L) ratio to (x3) or (x4) (p < 0.05). Null hypothesis (b) is rejected: a negative correlation is observed in max (P/L) ratio difference with dispensed multiple for Ketac Cem (p = 0.029).
Conclusion: For hand-mixed dental cements: (1) more consistent (P/L) ratios may be observed with multiple dispensations of powder & liquid; (2) maximum differences in (P/L) ratio may be negatively correlated with dispensation multiple in some materials.

Will your article be found? Authors choose a confusing variety of words to describe dental survival analyses

OBJECTIVES: Identify the words and phrases that authors used to describe time-to-event outcomes of dental treatments in patients.

MATERIALS AND METHODS: A systematic handsearch of 50 dental journals with the highest Citation Index for 2008 identified articles reporting dental treatment with time-to-event statistics (included "case" articles, n = 95), without time-to-event statistics (active "control" articles, n = 91), and all other articles (passive "control" articles n = 6796). The included and active controls were read, identifying 43 English words across the title, aim and abstract, indicating that outcomes were studied over time. Once identified, these words were sought within the 6796 passive controls. Words were divided into six groups. Differences in use of words were analyzed with Pearson's chi-square across these six groups, and the three locations (title, aim, and abstract).

RESULTS: In the abstracts, included articles used group 1 (statistical technique) and group 2 (statistical terms) more frequently than the active and passive controls (group 1: 35%, 2%, 0.37%, P < 0.001 and group 2: 31%, 1%, 0.06%, P < 0.001). The included and active controls used group 3 (quasi-statistical) equally, but significantly more often than the passive controls (82%, 78%, 3.21%, P < 0.001). In the aims, use of target words was similar for included and active controls, but less frequent for groups 1-4 in the passive controls (P < 0.001). In the title, group 2 (statistical techniques) and groups 3-5 (outcomes) were similar for included and active controls, but groups 2 and 3 were less frequent in the passive controls (P < 0.001). Significantly more included articles used group 6 words (stating the study duration) (54%, 30%, P = 0.001).

CONCLUSION: All included articles used time-to-event analyses, but two-thirds did not include words to highlight this in the abstract. There is great variation in the words authors used to describe dental time-to-event outcomes. Electronic identification of such articles would be inconsistent, with low sensitivity and specificity. Authors should improve the reporting quality. Journals should allow sufficient space in abstracts to summarize research, and not impose unrealistic word limits. Readers should be mindful of these problems when searching for relevant articles. Additional research is required in this field.

Influência da espessura do substrato dental sobre a eficácia clareadora e citotoxicidade de diferentes protocolos de clareamento

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Production and Characterization of Endocylanase from Bacillus Pumilus Using Solidstate Fermentation and its Application in 'Paper Pulp Processing

In the present studies it is clear that Bacillus pumilus xylanase is having the characteristic suited for an industrial enzyme (xylanases that are active and stable at elevated temperatures and alkaline pH are needed). SSF production of xylanases and its application appears to be an innovative technology where the fermented substrate is the enzyme source that is used directly in the bleaching process without a prior downstream processing. The direct use of SSF enzymes in bleaching is a relatively new biobleaching approach. This can certainly benefit the bleaching process to lower the xylanase production costs and improve the economics and viability of the biobleaching technology. The application of enzymes to the bleaching process has been considered as an environmentally friendly approach that can reduce the negative impact on the environment exerted by the use of chlorine-based bleaching agents. It has been demonstrated that pretreatment of kraft pulp with xylanase prior to bleaching (biobleaching) can facilitate subsequent removal of lignin by bleaching chemicals, thereby, reducing the demand for elemental chlorine or improving final paper brightness. Using this xylanase pre-treatment, has resulted in an increased of brightness (8.5 Unit) when compared to non-enzymatic treated bleached pulp prepared using identical conditions. Reduction of the consumption of active chlorine can be achieved which results in a decrease in the toxicity, colour, chloride and absorbable organic halogen (AOX) levels of bleaching effluents. The xylanase treatment improves drainage, strength properties and the fragility of pulps, and also increases the brightness of pulps. This positive result shows that enzyme pre-treatment facilitates the removal of chromophore fragments of pulp there by making the process more environment friendly

Protocol for a feasibility study of a self help cognitive behavioural therapy resource for the reduction of dental anxiety in young people

Background Childhood dental anxiety is very common, with 10–20 % of children and young people reporting high levels of dental anxiety. It is distressing and has a negative impact on the quality of life of young people and their parents as well as being associated with poor oral health. Affected individuals may develop a lifelong reliance on general anaesthetic or sedation for necessary dental treatment thus requiring the support of specialist dental services. Children and young people with dental anxiety therefore require additional clinical time and can be costly to treat in the long term. The reduction of dental anxiety through the use of effective psychological techniques is, therefore, of high importance. However, there is a lack of high-quality research investigating the impact of cognitive behavioural therapy (CBT) approaches when applied to young people’s dental anxiety. Methods/design The first part of the study will develop a profile of dentally anxious young people using a prospective questionnaire sent to a consecutive sample of 100 young people referred to the Paediatric Dentistry Department, Charles Clifford Dental Hospital, in Sheffield. The second part will involve interviewing a purposive sample of 15–20 dental team members on their perceptions of a CBT self-help resource for dental anxiety, their opinions on whether they might use such a resource with patients, and their willingness to recruit participants to a future randomised controlled trial (RCT) to evaluate the resource. The third part of the study will investigate the most appropriate outcome measures to include in a trial, the acceptability of the resource, and retention and completion rates of treatment with a sample of 60 dentally anxious young people using the CBT resource. Discussion This study will provide information on the profile of dentally anxious young people who could potentially be helped by a guided self-help CBT resource. It will gain the perceptions of dental care team members of guided self-help CBT for dental anxiety in young people and their willingness to recruit participants to a trial. Acceptability of the resource to participants and retention and completion rates will also be investigated to inform a future RCT.

Microstructure and Mineral Composition of Dental Enamel of Permanent and Deciduous Teeth

Purpose: This study evaluated and compared in vitro the microstructure and mineral composition of permanent and deciduous teeth`s dental enamel. Methods: Sound third molars (n = 12) and second primary molars (n = 12) were selected and randomly assigned to the following groups, according to the analysis method performed (n = 4): Scanning electron microscopy (SEM), X-Ray diffraction (XRD) and Energy dispersive X-ray spectrometer (EDS). Qualitative and quantitative comparisons of the dental enamel were done. The microscopic findings were analyzed statistically by a nonparametric test (Kruskal-Wallis). The measurements of the prisms number and thickness were done in SEM photomicrographs. The relative amounts of calcium (Ca) and phosphorus (P) were determined by EDS investigation. Chemical phases present in both types of teeth were observed by the XRD analysis. Results: The mean thickness measurements observed in the deciduous teeth enamel was 1.14 mm and in the permanent teeth enamel was 2.58 mm. The mean rod head diameter in deciduous teeth was statistically similar to that of permanent teeth enamel, and a slightly decrease from the outer enamel surface to the region next to the enamel-dentine junction was assessed. The numerical density of enamel rods was higher in the deciduous teeth, mainly near EDJ, that showed statistically significant difference. The percentage of Ca and P was higher in the permanent teeth enamel. Conclusions: The primary enamel structure showed a lower level of Ca and P, thinner thickness and higher numerical density of rods. Microsc. Res. Tech. 73:572-577, 2010. (C) 2009 Wiley-Liss. Inc.

A Longitudinal Three-Center Study of Dental Arch Relationship in Patients With Bilateral Cleft Lip and Palate

Objective: To compare and evaluate longitudinally the dental arch relationships from 4.5 to 13.5 years of age with the Bauru-BCLP Yardstick in a large sample of patients with bilateral cleft lip and palate (BCLP). Design: Retrospective longitudinal intercenter outcome study. Patients: Dental casts of 204 consecutive patients with complete BCLP were evaluated at 6, 9, and 12 years of age. All models were identified only by random identification numbers. Setting: Three cleft palate centers with different treatment protocols. Main Outcome Measures: Dental arch relationships were categorized with the Bauru-BCLP yardstick. Increments for each interval (from 6 to 9 years, 6 to 12 years, and 9 to 12 years) were analyzed by logistic and linear regression models. Results: There were no significant differences in outcome measures between the centers at age 12 or at age 9. At age 6, center B showed significantly better results (p = .027), but this difference diminished as the yardstick score for this group increased over time (linear regression analysis), the difference with the reference category (center C, boys) for the intervals 6 to 12 and 9 to 12 years being 10.4% (p = .041) and 12.9% (p = .009), respectively. Conclusions: Despite different treatment protocols, dental arch relationships in the three centers were comparable in final scores at age 9 and 12 years. Delaying hard palate closure and employing infant orthopedics did not appear to be advantageous in the long run. Premaxillary osteotomy employed in center B appeared to be associated with less favorable development of the dental arch relationship between 9 and 12 years.

Evaluating microfossil content of dental calculus from Brazilian sambaquis

To date, limited numbers of dental calculus samples have been analyzed by researchers in diverse parts of the world. The combined analyses of these have provided some general guidelines for the analysis of calculus that is non-destructive to archaeological teeth. There is still a need for a quantitative study of large numbers of calculus samples to establish protocols, assess the level of contamination, evaluate the quantity of microfossils in dental calculus, and to compare analysis results with the literature concerning the biology of calculus formation. We analyzed dental calculus from 53 teeth from four Brazilian sambaquis. Sambaquis are the shell-mounds that were established prehistorically along the Brazilian coast. The analysis of sambaqui dental calculi shows that there are relatively high concentrations of microfossils (phytoliths and starch), mineral fragments, and charcoal in dental calculus. Mineral fragments and charcoal are possibly contaminants. The largest dental calculi have the lowest concentrations of microfossils. Biologically, this is explained by individual variation in calculus formation between people. Importantly, starch is ubiquitous in dental calculus. The starch and phytoliths show that certainly Dioscorea (yam) and Araucaria angustifolia (Parana pine) were eaten by sambaqui people. Araceae (arum family), Ipomoea batatas (sweet potato) and Zea mays (maize) were probably in their diet. (C) 2009 Elsevier Ltd. All rights reserved.